If you discover that material is missing or defective, contact our customer service department immediately:

Size: px
Start display at page:

Download "If you discover that material is missing or defective, contact our customer service department immediately:"

Transcription

1 General Information Open the pack list on the crate s exterior. Locate the shop drawings and installation instruction inside the box. Review contents and make sure all parts are present. For a rectangular installation, the pack list will include the number of modules and frame pieces. For odd-shaped installations, a drawing will be supplied identifying the module layout in numbered sequence. If you discover that material is missing or defective, contact our customer service department immediately: Important Notes - Do Not Overlook Prior to installation, ensure that the material is stored indoors and has acclimated to the environment s temperature for 24 hours. Assess the site condition prior to installation ensuring the recess is: Free of debris and moisture The correct depth throughout Smooth and flat High spots should be ground down. Low spots should be filled with a self-leveling grout. The side walls of the recess should also be checked for plumb and defects as this could affect the frame installation (if applicable). If these conditions have been met, you can begin the installation. Tools Required You will need a level, hammer, 5/16 and 3/8 masonry drill bits, 1/8 Allen wrench, flathead screwdriver, #2 Phillips-head screwdriver, tape measure, carpenter s pencil or marker, shop vacuum, PPE (gloves, glasses, ear protection, etc.) and a trowel. Installation Instructions 1 Each frame has welded tabs with holes for mounting. 2 Begin dry-fitting all frame pieces into the recess. 3 It may be necessary to use shims to set the frame flush with the finished floor.

2 4 The shims are available in different thicknesses and are stackable to achieve custom thicknesses. 5 Use a 5/32 masonry bit to drill into the substrate at each welded tab hole for the anchor. 6 Fasten the supplied masonry anchors into the pre-drilled holes to attach the frame. 7 To make the sub-floor level with the bottom frame leg, use non-shrink grout (Quikrete 1585 or similar) and trowel flush with the top of the bottom leg of the level base frame. The recess should be smooth and flat when 8 Use a rag to clean the excess grouting from the top of the frame leg. Allow 24 hours for the grout to dry before continuing with the installation. 9 Dry fit all grid modules into the area per the supplied shop drawings. 10 Each module is tagged identify a specific location per the drawing. 11 Adjust each module to ensure consistent spacing and alignment. 12 Once you have achieved perfect alignment, begin marking for the hidden lockdown locations.

3 13 A full-sized panel should include a total of 12 lockdowns: one in each corner, a row centered along the panel horizontally and two rows off-set 12 from each side of the panel s vertical centerline, as shown in Figure A. 14 For a smaller panel, a lockdown should be placed in each corner and along the vertical centerline of the panel, with any remaining lockdowns placed every 24, vertically and horizontally (if necessary) as shown in Figure B. 15 All perimeter lockdowns should be offset far enough from the edge to avoid drilling into the frame s bottom leg. 16 Use a tape measure to locate each lockdown location. 17 Mark two surface wires to identify the center of each hidden lockdown location on the grid panel. 18 Be sure to keep the lockdown locations consistently aligned across the module wires (reference photo on slide 17). 19 Continue marking each location and ensure that the marks align in both directions. 20 Centered between the two surface wires that were previously marked, transfer the mark to the substrate at each hidden lockdown location. 21 A 1/8 drill bit or center punch tool can be used.

4 22 Shown: center punch option. 23 Continue transferring the mark to the substrate at each hidden lockdown location. 24 Use small prying tools to lift the grid s edge. 25 Lift the first module to begin mounting the hidden lockdowns. 26 Stand grid on its edge and locate the two marks on the surface wires. 27 Insert a small tool between the marks to later identify the location. 28 On the opposite side, install the hidden lockdown with the small tool acting as the center. 29 Assemble hidden lockdown by inserting the screw through the clip s hole. 30 Install the lockwasher onto the screw on the clip s opposite side.

5 31 Push the assembled clip into the grid so that the clip s center is aligned with the small tool. 32 Use a screwdriver to seat the hook of the clip around the support bar. 33 This is what an installed clip should look like on each side of the grid. 34 It is time to begin drilling the lockdown holes into the substrate. The lead shield and setting tool are shown here. Note: the shield s cone installs into the hole first. 35 At each location where the hole was transferred, drill a 3/8 hole, 5/8 deep into the substrate. 36 Install the lead shield and lock with the setting tool. 37 After all hidden lockdowns and lead shields have been installed, you are ready to install the module. 38 Align every screw into every lead shield. 39 Beginning in the center and working your way out to the edges, start the screws with a 1/8 Allen wrench.

6 40 Go back to the center and lightly draw down the screws, working your way out to the edges. 41 Go back to the center and tighten the screws, working your way out to the edge. Repeat this process for the remaining modules. 42 If building construction is to continue, protect the grid with plywood sheathing. 43 Care & Maintenance: Once the installation is complete, use denatured alcohol to remove the marks on the grids and clean with a mop.

VYTEX PREMIUM SLIDING GLASS DOOR. Table of Contents. Precautions and Safety 2. Tools Required...3. Inspect and Prepare Door...4

VYTEX PREMIUM SLIDING GLASS DOOR. Table of Contents. Precautions and Safety 2. Tools Required...3. Inspect and Prepare Door...4 VYTEX PREMIUM SLIDING GLASS DOOR Table of Contents Precautions and Safety 2 Tools Required...3 Inspect and Prepare Door...4 Hardware and Parts Check List....4 Master Frame Assembly 5 Master Frame Installation..7

More information

STACKING MULTI-SLIDE DOOR SYSTEM INSTALLATION INSTRUCTIONS

STACKING MULTI-SLIDE DOOR SYSTEM INSTALLATION INSTRUCTIONS STACKING MULTI-SLIDE DOOR SYSTEM INSTALLATION INSTRUCTIONS 1290363 Revision 1 12/16 Page 1 Weather Shield Mfg., Inc. NOTICE CAUTION! Failure to install and maintain our product according to these instructions

More information

Two Panel Frameless Bypass Door

Two Panel Frameless Bypass Door INSTALLATION INSTRUCTIONS Two Frameless Bypass Door Series 00 Please Record Model Number From Carton Label Here Please read these instructions carefully to familiarize yourself with the required tools,

More information

P a r k c o n s o l e s i n k a s s e m b l y i n s t r u c t i o n s

P a r k c o n s o l e s i n k a s s e m b l y i n s t r u c t i o n s P a r k c o n s o l e s i n k a s s e m b l y i n s t r u c t i o n s Before You Begin: Professional installation by two-person crew is required for this fixture. Install water supply and drain piping

More information

WALL MOUNT LOCKER ASSEMBLY. 208 Chestnut St, Reading, PA (610)

WALL MOUNT LOCKER ASSEMBLY. 208 Chestnut St, Reading, PA (610) WALL MOUNT LOCKER ASSEMBLY 208 Chestnut St, Reading, PA 19602 (610)376-2666 Locker Assembly Wall Mount: locker Installation Introduction: Before beginning, check to ensure the floor is level, and the wall

More information

PFW Installation Guide Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d Installation, Installatie gids

PFW Installation Guide Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d Installation, Installatie gids Maximum Flat Panel Weight: 100 lb. / 45.35 kg. Included Components Wall Mount (Qty 1) Extension Bracket (Qty 1 Pair) Bracket (Qty 1 Pair) 5/16 Flat Washers (Qty 4) Universal Spacers (Qty 8) M5 Allen Driver

More information

Frameless Fixed Panel Slider

Frameless Fixed Panel Slider INSTALLATION INSTRUCTIONS Frameless Fixed Panel Slider QCI-5279 SINGLE ROLLER WITH ANTI-JUMP DOUBLE ROLLERS QCI5279 Rev Page Certified 08/09/6 Tools: To install your New Shower Enclosure, you may need

More information

Installation Instructions. Oakmont Folding Doors

Installation Instructions. Oakmont Folding Doors Before You Start For quick and easy installation of your Oakmont folding door, read these instructions thoroughly. A few minutes of prior planning will make the job easier and ensure years of trouble-free

More information

Installing flat panels on the MPL15 wall mount

Installing flat panels on the MPL15 wall mount Installing flat panels on the MPL15 wall mount The MPL15 (DS-VW775) is a full-service video wall mount that can accommodate tiled LCD panels with up to a 400 x 400 mm VESA pattern in portrait and landscape

More information

Independent Containment System (ICS)

Independent Containment System (ICS) Installing the Independent Containment System (ICS) Complete these instructions to install the Independent Containment System (ICS). Prerequisites This installation requires a team of at least two people.

More information

ESA-100 Fixed Sidelite/Non Breakout

ESA-100 Fixed Sidelite/Non Breakout /Non Breakout Exterior View Installation Instructions For use with ESA II Controller 1 Tools Required: Suggested Fasteners Required - (Not supplied) Screwdrivers Small Straight (FlatBlade) - for Terminal

More information

BASIC TOOLS AND MATERIALS NEEDED. Introduction HOW TO CARE FOR YOUR DOOR

BASIC TOOLS AND MATERIALS NEEDED. Introduction HOW TO CARE FOR YOUR DOOR DO IT RIGHT! Use a Kohler Certified Installer, (KCI), for the installation of your Kohler Shower Door. Contact your Kohler Distributor/Showroom or call Kohler at 1-800-4-KOHLER for the KCI nearest you.

More information

Installation Instruction

Installation Instruction Tools Needed for Assembly Stud finder (for wood stud wall) Pencil Mark Electric drill Wood Stud Wall Installation Step 1. Locate the Wood Studs Installation Instruction Drill bit (for wood stud wall) Masonry

More information

Laminate Cabinet Installation Instructions

Laminate Cabinet Installation Instructions Laminate Cabinet Installation Instructions www.easygaragestorage.com/installation How To Use These Instructions Thank you for your purchase! Please read each step of this manual thoroughly to ensure proper

More information

TrendWall Floor-To-Ceiling Panels Installation Instruction

TrendWall Floor-To-Ceiling Panels Installation Instruction TrendWall Floor-To-Ceiling Panels Installation Instruction TrendWall Components Covered by this Instruction: Crown (and accessories) Floor Plate Solid Panel Filler Panel Wall Channel Door Section Pilaster

More information

K ARICA ROUND SHOWER ENCLOSURE

K ARICA ROUND SHOWER ENCLOSURE K-7050 ARICA ROUND SHOWER ENCLOSURE 1. BEFORE YOU BEGIN HOW TO USE THESE INSTRUCTIONS Please read these instructions carefully to familiarize yourself with the required tools, materials, and installation

More information

PFW 6875 Installation Guide Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d Installation, Installatie gids

PFW 6875 Installation Guide Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d Installation, Installatie gids Maximum Flat Panel Weight: 160 lb. / 72.57 kg. Included Components Wall Mount (Qty 1) Extension Brackets (Qty 2) Bracket (Qty 1 Pair) 5/16 Flat Washers (Qty 4) Universal Spacers (Qty 8) M5 Allen Driver

More information

TRUE TECHNICAL SERVICE MANUAL - ALL MODELS. DOORS/DRAWERS/LIDS

TRUE TECHNICAL SERVICE MANUAL - ALL MODELS.  DOORS/DRAWERS/LIDS DOORS/DRAWERS/LIDS 55 56 NOTES DOORS/DRAWERS/LIDS Swing s 73 74 NOTES INSTALLATION OF A GDM-SWING DOOR Phillips Head Screwdriver (2) - 1/8" Drift Punches (forged) Top Bracket NOTE: It may be necessary

More information

ESA-300 Full Breakout

ESA-300 Full Breakout Interior View 0 Installation Instructions For use with ESA II Controler DORMA AUTOMATICS, Inc. 94 Sherwood Drive Toll-Free: 877-67-6 DL844-00 Lake Bluff, IL 60044 Fax: 877-4-7999 Rev. /07 Tools Required:

More information

Installation Manual for Metal Emperor Lockers

Installation Manual for Metal Emperor Lockers P a g e 1 Table of Contents Page General Notes and Tools Required 2-3 Assemble Shelves with Coat Hooks/Coat Rods 4 Fastening Chart 5 Knock Down Locker Assembly (Banks of Three) 6-12 Appendix A: Dress End

More information

3-LITE PATIO DOOR INSTALLATION INSTRUCTIONS

3-LITE PATIO DOOR INSTALLATION INSTRUCTIONS 3-LITE PATIO DOOR INSTALLATION INSTRUCTIONS IMPORTANT: Read the instructions and familiarize yourself with the door parts and pieces before beginning assembly and installation. TOOLS NEEDED: Tape Measure

More information

Series 7650 Installation Instructions Sliding Glass Door

Series 7650 Installation Instructions Sliding Glass Door Series 7650 Installation Instructions Sliding Glass Door Things to Know Before You Start Things to Know Before You Start Removal of Old Fenestration Products Ensure any old fenestration products are removed

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS A CSW Industrials Company FGLP with Cast-In Frames FGLP-A, FGLP-C, FGLP-D IMPORTANT The following instructions are very important. Read them carefully, and be sure you understand

More information

4-lite Patio Door. Installation Instructions

4-lite Patio Door. Installation Instructions 4-lite Patio Door Installation Instructions IMPORTANT: Read the instructions and familiarize yourself with the door parts and pieces before beginning assembly and installation. Note: Only the 5-0 x 6-8

More information

ESA-200 Fixed Sidelite

ESA-200 Fixed Sidelite Exterior View Installation Instructions For use with ESA II Controller 1 Tools Required: Suggested Fasteners Required - (Not supplied) Screwdrivers Small Straight (FlatBlade) - for Terminal Block wiring

More information

Dura-Lock Roof System

Dura-Lock Roof System DLR-14 Dura-Lock Roof System Assembly and Installation Instructions Read the instructions before starting the job. They explain the steps required to produce a finished product that will meet factory specifications.

More information

x2 1/4 (6mm) Floor Anchor

x2 1/4 (6mm) Floor Anchor INSTALLATION GUIDE Main Components x1 Rail x5 Wall Spacer x2 Anti-jump Block x2 Straight Strap x1 Right Stopper x1 Left Stopper x5 5/16 (8mm x 60mm) Carriage Bolt x5 5/16 (8mm x25mm) Anchor x5 5/16 (8mm

More information

BioPrism Solid Surface

BioPrism Solid Surface Please read all instructions before installing products. These instructions are intended for use with InPro s standard toilet partitions, which include 58 high doors and wall panels, when deviating from

More information

INSTALLATION AND CARE INSTRUCTIONS

INSTALLATION AND CARE INSTRUCTIONS INSTALLATION AND CARE INSTRUCTIONS Skylight Manually Operated Honeycomb Shades 20 C8-10-1806 2/15 1 INTRODUCTION Thank you for purchasing our product. Your new shade has been custom built for you from

More information

C-Series & S-Series Classic Frame with Transom (Single or Pair)

C-Series & S-Series Classic Frame with Transom (Single or Pair) 1. TOOLS REQUIRED Tape measure 6' magnetic level 3' magnetic level Safety Glasses Screw gun #2 Screwdriver tip #3 Screwdriver tip Philips Head screwdriver (Used to move frame on wall using oval slots on

More information

MOTORIZED STANDARD SHADE WITH CABLES Installation Instructions

MOTORIZED STANDARD SHADE WITH CABLES Installation Instructions Tools Needed Drill Measuring Tape Pencil 2 Level Plumb Line ¼ Masonry Drill Bit Hammer Linesmans Pliers Cable Cutters Phillips & Flat-Head Screw Driver 11/32 Socket or Open End Wrench 5/32 Allen Wrench

More information

Setup. The Faraday Cage is available in two types of configurations. Cage for mounting to a full perimeter enclosure on series tables.

Setup. The Faraday Cage is available in two types of configurations. Cage for mounting to a full perimeter enclosure on series tables. Faraday CageSetup, 2017 Setup The Faraday Cage is available in two types of configurations. Cage for mounting to a full perimeter enclosure on 63-500 series tables. Cage with a base plate for use on a

More information

Installation Manual MODEL NE-42

Installation Manual MODEL NE-42 Installation Manual MODEL NE-42 GET TO KNOW YOUR UNIT 1 1. CROSS BRACES - Stud Finder - 12-14 Level - Tape Measure - Small Flathead Screwdriver Tools Needed: - Electric Drill (with 1/4 & 1/8 drill bit)

More information

How To Measure Your Finished Opening

How To Measure Your Finished Opening 3000 Series Bifold Doors How To Measure Your Finished Opening MEASURE FROM RIGHT TO LEFT 2 PLACES (WIDTH) MEASURE FROM TOP TO BOTTOM 2 PLACES (HEIGHT) Tools Required for Assembly: Tools Needed: Phillips

More information

LAN Locker Adjustable Shelves

LAN Locker Adjustable Shelves Adjustable Shelves LAN LOCKER ADJUSTABLE SHELVES * Adjustable Shelves are available for LAN LOCKER widths: 24, 30, 48, 60, and 72. * When installing more than one Adjustable Shelf, it is recommended that

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS SOLID PHENOLIC TOILET PARTITIONS 1080 DuraLine Series 1180 DuraLine Series Class-A Fire Rated IMPORTANT: Review these instructions thoroughly prior to installation. FLOOR ANCHORED

More information

Steel Solutions USA 602 E. Walnut Street Watseka, IL p: (888) f: (815)

Steel Solutions USA 602 E. Walnut Street Watseka, IL p: (888) f: (815) Steel Solutions USA 602 E. Walnut Street Watseka, IL 60970 p: (888) 875-5004 f: (815) 432-3364 sales@steelsolutionsusa.com Published February 2011 2011 Steel Solutions USA. All rights reserved. version

More information

ASSEMBLY AND INSTALLATION INSTRUCTIONS for Premium Aluminum and Premium Atlantic Aluminum Sliding Patio Doors (JII020)

ASSEMBLY AND INSTALLATION INSTRUCTIONS for Premium Aluminum and Premium Atlantic Aluminum Sliding Patio Doors (JII020) for Premium Aluminum and Premium Atlantic Aluminum Sliding Patio Doors (JII020) Thank you for selecting jeld-wen products. Attached are jeld-wen s recommended installation instructions for Premium Aluminum

More information

INOVO 2-LITE SLIDING PATIO DOOR

INOVO 2-LITE SLIDING PATIO DOOR INOVO 2-LITE SLIDING PATIO DOOR ASSEMBLY AND INSTALLATION INSTRUCTIONS IMPORTANT: READ THE INSTRUCTIONS AND FAMILIARIZE YOURSELF WITH THE DOOR PARTS AND PIECES BEFORE BEGINNING ASSEMBLY AND INSTALLATION.

More information

Frameless Inline Door With Return QCI5263

Frameless Inline Door With Return QCI5263 INSTALLATION INSTRUCTIONS Frameless Inline Door With Return QCI5263 WALL MOUNT HINGES FRAMELESS DOOR / PANEL / RETURN PANEL QCI5263 REV. 0 Page 1 Certified 06/17/2016 Parts List with wall mount hinges

More information

Display Shelving Installation Instructions

Display Shelving Installation Instructions Display Shelving Installation Instructions Top Rail (R-T) Back (BE) (R-C) Splicer Rail (R-S) 78 H to 120 H only Uprite (U) Uprite End Trim (UET) Shelf Back (BE) Base End Trim (BET) (R-C) 96 H to 120 H

More information

Frameless Inline Door QCI5254

Frameless Inline Door QCI5254 INSTALLATION INSTRUCTIONS Frameless Inline Door QCI5254 FRAMELESS DOOR / PANEL QCI5254 REV. 0 Page 1 Cer fied 06/16/2016 Parts List with wall mount hinges *Quanes may vary QCI5254 REV. 0 Page 2 Cer fied

More information

Installation and Assembly: Flat Video Wall Mount For 40" to 65" Flat Panel Displays

Installation and Assembly: Flat Video Wall Mount For 40 to 65 Flat Panel Displays Installation and Assembly: Flat Video Wall Mount For 40" to 65" Flat Panel Displays Model: DS-VW665 Maximum Load Capacity: 125 lb (57 kg) 1 of 11 ISSUED: 03-22-12 SHEET #: 125-9288-4 06-25-13 NOTE: Read

More information

ICU TRACKLESS SLIDING DOOR

ICU TRACKLESS SLIDING DOOR Interior View 0 Installation Instructions Tools Required: Screwdrivers Small Straight (Flat Blade) - for Terminal Block wiring # Phillips (Crosspoint) - for various #8, #0, and #4 screws Wrenches / Sockets

More information

Introduction. Depending on your kennel project, you may have some or all of the following hardware: Part # Description Part # Description 1468

Introduction. Depending on your kennel project, you may have some or all of the following hardware: Part # Description Part # Description 1468 Introduction Thank you very much for your investment in Mason kennels. We take great pride in providing our customers with the highest quality animal enclosures combined with an enjoyable ordering experience.

More information

PLEATED SHADE ARCH INSIDE MOUNT GETTING STARTED. A few simple tools are required: STANDARD HARDWARE

PLEATED SHADE ARCH INSIDE MOUNT GETTING STARTED. A few simple tools are required: STANDARD HARDWARE HONEYCOMB AND PLEATED SHADE ARCH GETTING STARTED INSIDE MOUNT A few simple tools are required: HALF ARCH INSTALLATION Your half arch has been shipped in the closed osition. When fanned, the rails will

More information

Assembly and Installation Guide

Assembly and Installation Guide The Easy Hang Closet Solution SM Install Your elfa In An Instant. Enjoy The Benefits For A Lifetime. Basic Tools For elfa Assembly and Installation Level Hand or Power Drill Drill Bits 1/8", 3/8", 5/16"

More information

INSTALLATION INSTRUCTIONS FOR PLASCORE F5075 FRAME WALL

INSTALLATION INSTRUCTIONS FOR PLASCORE F5075 FRAME WALL INSTALLATION INSTRUCTIONS FOR PLASCORE F5075 FRAME WALL The following information is provided by Plascore, Inc., as a general guideline for the installation of the F5075 Frame Wall System. This information

More information

Installation Manual for Metal Toilet Partitions Standard Series

Installation Manual for Metal Toilet Partitions Standard Series For Video instructions http://www.hadrian-inc.com/tech-data/installation/toilet-partitions.aspx P a g e 1 Table of Contents Page General Notes and Tools Required 3 STEP 1: Establish Floor Bracket Locations

More information

southpaw enterprises, inc.

southpaw enterprises, inc. southpaw enterprises, inc. Store these instructions with the enclosed maintenance checklist in a safe place. You may also access them on our website. Instruction Sheet Convertible Climbing Wall - Block/Brick

More information

#11179 Wellington ARBOR

#11179 Wellington ARBOR #11179 Wellington ARBOR Assembly INSTRUCTIONS TOOLS NEEDED Tape Measure Variable Speed Drill with #2 Phillips Bit (recommended) or Phillips Screwdriver Hammer or Mallet ARBOR SIDE PANEL ASSEMBLY (Refer

More information

IMPORTANT: One Corner Entry Shower Door requires two cartons.

IMPORTANT: One Corner Entry Shower Door requires two cartons. IMPORTANT: You should check with your local plumbing or building code agency about this product for compliance before it is installed. IMPORTANT: One Entry Shower Door requires two cartons. 95302-2-AB

More information

Equilibrium. Conference Table. Installation Instruction. Revision B 11/07/16

Equilibrium. Conference Table. Installation Instruction. Revision B 11/07/16 Equilibrium Conference Table Installation Instruction Revision B 11/07/16 Equilibrium End User Agreement Enwork Equilibrium table bases must be installed directly onto a four inch minimum thickness concrete

More information

FRAMELESS DOOR / PANEL WITH WALL MOUNT HINGES QCI5274

FRAMELESS DOOR / PANEL WITH WALL MOUNT HINGES QCI5274 FRAMELESS DOOR / PANEL WITH WALL MOUNT HINGES QCI5274 QCI0274 QCI5274 REV. Rev. 1 0 Page Page 1 1 Date Certified: Certified 06/16/2016 10/01/10 Parts List with wall mount hinges ITEM NO. Part # DESCRIPTION

More information

PFW 6870 Installation Guide Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d Installation, Installatie gids

PFW 6870 Installation Guide Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d Installation, Installatie gids Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d Installation, Installatie gids Max: 72kg/160lbs MOUIN_PFW6870_V01 Included Components Wall Mount (Qty 1) Bracket (Qty 1 Pair)

More information

GRID PANEL SYSTEM Installation Instructions

GRID PANEL SYSTEM Installation Instructions Ceiling Top Edge Trim Shim GRID PANEL SYSTEM Installation Instructions Installation is simple & fast using Ambienta Grid Horizontal Reveal Option for Horizontal Reveals & Edge Trim to be punched with slotted

More information

Jenny Legs Assembly Instructions

Jenny Legs Assembly Instructions Jenny Legs Assembly Instructions R EXTENDED PHILLIPS BIT MM ALLEN WRENCH 6MM HEX DRIVE /" 007 Steelcase Inc. Grand Rapids, MI 90 U.S.A. Printed in U.S.A. Page of 6 88000 Rev F Jenny Club Instructions:

More information

Replacement Guide. For Handle Side Z-bar on Fullview Doors with Laminated Glass and Multi-Point Locking System RECOMMENDED TOOLS:

Replacement Guide. For Handle Side Z-bar on Fullview Doors with Laminated Glass and Multi-Point Locking System RECOMMENDED TOOLS: Replacement Guide For Handle Side Z-bar on Fullview Doors with Laminated Glass and Multi-Point Locking System IMPORTANT: READ ENTIRE GUIDE BEFORE BEGINNING INSTALLATION. PLEASE NOTE: Proper assembly, installation

More information

Installation Instructions

Installation Instructions Installation Instructions For Models: Model Number / Description File Name 1540 Classic Series P-Lam Toilet Partitions 1540.pdf 1 INSTALLATION INSTRUCTIONS LAMINATED PLASTIC TOILET PARTITIONS 1540 Classic

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS SOLID PHENOLIC TOILET PARTITIONS 1080 DuraLineSeries Class-A Fire Rated Includes Institutional Hardware Option.67 IMPORTANT: Storage and Handling Information on last page. Review

More information

A-935 RODA WALL MOUNT HINGES

A-935 RODA WALL MOUNT HINGES INSTALLATION INSTRUCTIONS A-935 RODA WALL MOUNT HINGES NEED INSTALLATION HELP? Call 1-800-45-BASCO (452-2726) Monday - Friday 8:00 A.M. - 4:30 P.M. Eastern Time FRAMELESS DOOR / PANEL CELESTA QCI0274 REV.

More information

METAL BLINDS. Deluxe GETTING STARTED OPTIONAL HARDWARE. A few simple tools are required: STANDARD HARDWARE

METAL BLINDS. Deluxe GETTING STARTED OPTIONAL HARDWARE. A few simple tools are required: STANDARD HARDWARE METAL BLINDS Deluxe GETTING STARTED OPTIONAL HARDWARE A few simple tools are required: Steel Tape Measure Pencil Level Hold Down Brackets with Screws Extension Bracket Power Drill and Drill Bits Flathead

More information

3/16 FRAMELESS SERIES BY-PASS TUB AND SHOWER ENCLOSURES #3344, 3345, 3037

3/16 FRAMELESS SERIES BY-PASS TUB AND SHOWER ENCLOSURES #3344, 3345, 3037 / FRAMELESS SERIES BY-PASS #, 5, 07 PLEASE READ THOROUGHLY BEFORE STARTING INSTALLATION Item 5 7 8 9 0 5 7 8 Part # 09/050 0 05 A05 8 0 0 0 70 0 09 5 5 0 0 7 0 Description Tub Header Stay Clean Sill Tub

More information

ICU TRACK SLIDING DOOR

ICU TRACK SLIDING DOOR Interior View 0 Installation Instructions Tools Required: Screwdrivers Small Straight (Flat Blade) - for Terminal Block wiring # Phillips (Crosspoint) - for various #8, #0, and # screws Wrenches / Sockets

More information

Cardo DOOR & RETURN SHOWER ENCLOSURE INSTALLATION PLEASE READ THESE INSTRUCTIONS CAREFULLY.

Cardo DOOR & RETURN SHOWER ENCLOSURE INSTALLATION PLEASE READ THESE INSTRUCTIONS CAREFULLY. Cardo DOOR & RETURN SHOWER ENCLOSURE INSTALLATION PLEASE READ THESE INSTRUCTIONS CAREFULLY. IT IS RECOMMENDED TO USE A TRAINED SHOWER INSTALLER FOR THIS SHOWER TO OBTAIN THE BEST INSTALLATION. D Square

More information

PL-91. Frameless Door with Panel. 202 Anderson Ave., Belvue, KS Phone: Fax:

PL-91. Frameless Door with Panel. 202 Anderson Ave., Belvue, KS Phone: Fax: 202 Anderson Ave., Belvue, KS 66407 Phone: 800-669-9867 Fax: 800-393-6699 www.onyxcollection.com 800-643-1514 www.alumaxshowerdoor.com PL-91 Frameless Door with Panel Full Showers Bench Seat Showers PL91-0318

More information

GRAMERCY POWDER WASHSTAND ASSEMBLY INSTRUCTIONS. 1. Storage. 1. Keep marble top in its crate until installation.

GRAMERCY POWDER WASHSTAND ASSEMBLY INSTRUCTIONS. 1. Storage. 1. Keep marble top in its crate until installation. 1. Storage 1. Keep marble top in its crate until installation. 2. Store crate vertically in a place safe from being hit or knocked over. 3. Do not stack anything on top of the crate. 2. Opening crate 1.

More information

s t o r a g e & i n s t a l l a t i o n o f y o u r m a r b l e t o p

s t o r a g e & i n s t a l l a t i o n o f y o u r m a r b l e t o p s t o r a g e & i n s t a l l a t i o n o f y o u r m a r b l e t o p 1. Storage 1. Keep marble top in it s crate until installation. 2. Store crate vertically in a place safe from being hit or knocked

More information

compile system INSTALLATION GUIDE Updated January 2019

compile system INSTALLATION GUIDE Updated January 2019 INSTALLATION GUIDE Updated January 09 compile system Table of Contents Panels 0 Quick Connect Clips 0 Lock Clips 0 Panel Trims 0 Privacy Glass 0 Post Base Covers 04 Electrical 04 Power Distribution Harness

More information

Series 7600 Installation Instructions Aluminum Multi-Slide Door (Pocketing)

Series 7600 Installation Instructions Aluminum Multi-Slide Door (Pocketing) Series 7600 Installation Instructions Aluminum Multi-Slide Door (Pocketing) Things to Know Before You Start Things to Know Before You Start Removal of Old Fenestration Products Ensure any old fenestration

More information

GETTING STARTED. Instructions IMPORTANT PS B PS B. Record the serial number from the tag on the door front.

GETTING STARTED. Instructions IMPORTANT PS B PS B. Record the serial number from the tag on the door front. PS-15-20-B IMPORTANT Instructions Record the serial number from the tag on the door front. Keep keys in a secure place away from children. DO NOT STORE KEYS INSIDE SAFE GETTING STARTED When you first receive

More information

Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens

Installation and Assembly - Universal Articulating Swivel Double-Arm for 42 - 60 Plasma Screens Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens Models: PLAV 70-UNL, PLAV 70-UNL-S PLAV 70-UNLP, PLAV 70-UNLP-S R This product is UL Listed. It must be

More information

LCD LIFT Flat Panel Display System Installation Manual. Table of Contents

LCD LIFT Flat Panel Display System Installation Manual. Table of Contents LCD LIFT Flat Panel Display System Installation Manual Table of Contents Page Installation Overview... 2 Trim Ring Installation... 3 LCD Lift Installation....4 Actuator Switch Installation.5 Top Plate

More information

Extra Wide Heavy Duty Plastic Lockers Series Locker Installation Instructions

Extra Wide Heavy Duty Plastic Lockers Series Locker Installation Instructions Locker Installation Instructions Thank you for selecting Extra Wide Heavy Duty Plastic Lockers. We are confident that the quality and construction of the lockers will prove to be a good investment. These

More information

Installation Instructions

Installation Instructions FORD 20K Industry Standard Rail Custom Mounting Kit #2738 Gross Trailer Weight (Maximum)...20,000 lbs. Vertical Load Weight (Max. Pin Weight)...5,000 lbs. SYSTEM TOW CAPACITY Please note, in order to determine

More information

Track Rack. * Track Racks are not lockable

Track Rack. * Track Racks are not lockable The Track Rack s unique staggered, sliding hook design creates the greatest parking efficiency while still providing easy access to any particular bike. When adding or removing a bike to the rack, simply

More information

SHOWERGLIDE 600B, 690B, 692B, SERIES

SHOWERGLIDE 600B, 690B, 692B, SERIES Installation Instructions SHOWERGLIDE SERIES 600B, 60B, 6B, 6B, 65B, 67B IMPORTANT: You should check with your local plumbing or building code agency about this product for compliance before it is installed.

More information

WINDOW REPLACEMENT INSTRUCTIONS FOR CASEMENT, DOUBLE-HUNG AND CLAD FRAME WINDOWS USING FRAME SCREWS

WINDOW REPLACEMENT INSTRUCTIONS FOR CASEMENT, DOUBLE-HUNG AND CLAD FRAME WINDOWS USING FRAME SCREWS WINDOW REPLACEMENT INSTRUCTIONS FOR CASEMENT, DOUBLE-HUNG AND CLAD FRAME WINDOWS USING FRAME SCREWS These instructions were tested developed for replacing windows in wood-frame wall construction systems

More information

Installing the Profile Privacy Panel. Assemble top mounting bracket. Prerequisites. Tools

Installing the Profile Privacy Panel. Assemble top mounting bracket. Prerequisites. Tools Installing the Profile Privacy Panel Complete these instructions to install the Profile Privacy Panel. Privacy panels are available in various heights to match tiers and include mounting hardware for slat

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS HIGH PRESSUE LAMINATE (HPL) TOILET PARTITIONS 1030 TrimLineSeries 1040 DesignerSeries Includes continuous hardware option.65. IMPORTANT: Storage and Handling Information on last

More information

INSTALLATION INSTRUCTION

INSTALLATION INSTRUCTION INSTALLATION INSTRUCTION Plastic Laminate Series contents page 1030 TrimLineSeries...2-21 1040 DesigerSeries...2-21 Urinal Screens, Benches, Shower Seats...22-31 2030 TrimLineSeries Maximum Privacy...32-47

More information

INOVO 4-LITE SLIDING PATIO DOOR ASSEMBLY AND INSTALLATION INSTRUCTIONS

INOVO 4-LITE SLIDING PATIO DOOR ASSEMBLY AND INSTALLATION INSTRUCTIONS INOVO 4-LITE SLIDING PATIO DOOR ASSEMBLY AND INSTALLATION INSTRUCTIONS IMPORTANT: READ THE INSTRUCTIONS AND FAMILIARIZE YOURSELF WITH THE DOOR PARTS AND PIECES BEFORE BEGINNING ASSEMBLY AND INSTALLATION.

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS LAMINATED P LASTIC TOILET PArTITIONS 1540 ClassicSeries with Options IMPORTANT: Storage and Handling Information on last page. For faster, easier installation, please review these

More information

Frameless Bypass Slider

Frameless Bypass Slider INSTALLATION INSTRUCTIONS Frameless Bypass Slider QCI-5301 Heavy Glass Bypass Slider with Exposed Rollers QCI5301 Rev 0 Page 1 Certified 11/1/2016 Tools: To install your New Shower Enclosure, you may need

More information

BARN DOOR HARDWARE KIT

BARN DOOR HARDWARE KIT INSTALLATION GUIDE Main Components x1 Rail x5 Wall Spacer x2 Anti-jump Block x2 Bent Strap x1 Right Stopper x1 Left Stopper x5 5/16 (8mm x 60mm) Carriage Bolt x5 5/16 (8mm x25mm) Anchor x5 5/16 (8mm x

More information

Shop Style Miter Saw Stand Kit

Shop Style Miter Saw Stand Kit Quality Power Tool Accessories OWNER S MANUAL Assembled Unit Shown Without Shelves & Wings Assembled With Shelves & Wings Shop Style Miter Saw Stand Kit Model 2850 IMPORTANT Read and understand all safety

More information

Installation Instructions for Vista Air Vertically Folding Walls

Installation Instructions for Vista Air Vertically Folding Walls Installation Instructions for Vista Air Vertically Folding Walls Use these instructions in conjunction with your shop drawings to see the specifics that are particular to the model you are installing.

More information

PLAYLAND 72 SPIRAL SLIDE 3.5 Posts, 3.5 Posts / 48 Grid and 5 Posts

PLAYLAND 72 SPIRAL SLIDE 3.5 Posts, 3.5 Posts / 48 Grid and 5 Posts PLAYLAND 72 SPIRAL SLIDE 3.5 Posts, 3.5 Posts / 48 Grid and 5 Posts USER GROUP: 2-12 RECOMMENDED CREW: 2 people TOOLS REQUIRED: T-30 TORX tool (supplied by manufacturer) T-45 TORX tool (supplied by manufacturer)

More information

PORCH-LOC INSTALLATION INSTRUCTIONS

PORCH-LOC INSTALLATION INSTRUCTIONS PORCH-LOC INSTALLATION INSTRUCTIONS 2017 HB&G Building Products, Inc. Porch-Loc Installation Instructions NOTE: DISCARD THE INSTALLATION INSTRUCTIONS AND HARDWARE THAT CAME IN YOUR PERMAPOST PACKAGING

More information

Ready To Go SimpleSpec tm. Installation Manual. For more information, please visit 3-form.com or call

Ready To Go SimpleSpec tm. Installation Manual. For more information, please visit 3-form.com or call Contents Overview ( 1) 3/8" Varia Panel = Cable Tensioner with Cover Plate KIT Stainless Steel: 3-15-1636-K Black Oxide: 3-15-2005-K Cable Tensioner with Cover Plate SS: 3-15-1636 BO: 3-15-2005 + M8 Thread

More information

Installation Instructions

Installation Instructions CHEVY / GMC 20K Industry Standard Rail Custom Mounting Kit #2724 Gross Trailer Weight (Maximum)...20,000 lbs. Vertical Load Weight (Max. Pin Weight)...5,000 lbs. SYSTEM TOW CAPACITY Please note, in order

More information

INSTALLATION GUIDE StreamLine Linear Drain

INSTALLATION GUIDE StreamLine Linear Drain INSTALLATION GUIDE StreamLine Linear Drain TM With Full Mortar Bed Adapter Kit Supply Drainage Support www.siouxchief.com TM StreamLine Linear Drain With Full Mortar Bed Adapter Kit When using Full Mortar

More information

Fold-A-Way Patio Door ASSEMBLY & INSTALLATION GUIDE

Fold-A-Way Patio Door ASSEMBLY & INSTALLATION GUIDE Fold-A-Way Patio Door ASSEMBLY & INSTALLATION GUIDE This instruction guide provides the minimum recommended procedures to correctly prepare the rough opening, install a fold-a-way patio door unit and apply

More information

Mount to the Wall INSTALLATION MANUAL

Mount to the Wall INSTALLATION MANUAL Mount to the Wall 15 Locate the Wooden Studs This step applies to wooden stud wall installation only. Determine and mark the exact locations of two stud centers on the wall. Wooden studs should be spaced

More information

InStallatIon InStruCtIonS for vinyl 2-lIte PatIo door assembled

InStallatIon InStruCtIonS for vinyl 2-lIte PatIo door assembled InStallatIon InStruCtIonS for vinyl -lite PatIo door assembled tools & materials you Will need: Measuring Tape Pencil Shims Square Hammer or Mallet Level Drill & Drill bits: 6", 8", 5 6", 7 6" Utility

More information

REVIVAL ACCESSORIES BEFORE YOU BEGIN A. HOW TO USE THESE INSTRUCTIONS B. PRODUCT NOTES C. ORDERING INFORMATION D. REQUIRED TOOLS AND MATERIALS

REVIVAL ACCESSORIES BEFORE YOU BEGIN A. HOW TO USE THESE INSTRUCTIONS B. PRODUCT NOTES C. ORDERING INFORMATION D. REQUIRED TOOLS AND MATERIALS REVIVAL ACCESSORIES BEFORE YOU BEGIN A. HOW TO USE THESE INSTRUCTIONS Please read these instructions carefully to familiarize yourself with the required tools, materials, and installation sequences. Follow

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS For Wallbed models: Do-It-Yourself BOOKLET #C90 WARNING! ALL MURPY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION

More information

Series----SP3600A SHOWER DOOR

Series----SP3600A SHOWER DOOR Series----SP3600A SHOWER DOOR INSTALLATION INSTRUCTIONS Please read these instructions carefully to familiarize yourself with the required tools, materials, and installation sequences. The Exploded Diagram

More information

Chapter 1. Beam and Sill Plates

Chapter 1. Beam and Sill Plates Chapter 1. Beam and Sill Plates 1.1 ESTABLISHING SQUARE SILL PLATE CHALK LINES 1.2 INSTALLING TREATED SILL PLATES 1.3 INSTALLING LAMINATE BEAM Tools needed by volunteers: Hammer Nail apron Tape measure

More information

All Terrain Flares 2014 Chevy Silverado

All Terrain Flares 2014 Chevy Silverado Page 1/8 Components: 1. Front Flares (2) 2. Rear Flares (2) Tools required: - Utility knife - #2 Phillips driver - Socket wrench - 13 mm Socket - 6 mm Allen Wrench - T-15 Torx bit - Trim Removal Tool -

More information