The Camden Privacy Screen

Transcription

1 ASSEMBLY INSTRUCTIONS The Camden Privacy Screen 0 5/8 in (66 cm) 7 / in (8 cm) 6 / in (6.5 cm) 90 in (9 cm) Post 66 in (68 cm) 78 in (98 cm) Please read through before starting assembly. IMPORTANT: CHECK THE INSIDE OF YOUR POSTS FOR ALL MATERIALS. Check Box for These Contents In the event of missing or defective parts please call our customer service department (Mon. to Fri. 8:00 AM to :00 PM EST). (UK Tel: () Mon. to Fri. :00 PM to 0:00 PM GMT).. Post Caps () 08. Decorative Beam End Caps () 005. Post Trim Caps () Horizontal Rails () 08 - x / x 79 / (5 x 9 x 0 cm) 5. Vertical Spindles () 09-7/8 x / x 65 / ( x.8 x 67 cm) 6. Horizontal Spindles () 0 - / x / x 79 / (.8 x.8 x 0 cm) 7. Posts () 0 - x x 90 - (0 x 0 x 9 cm) 8. Beams () 0 - / x 5 / x 88 /8 (.8 x x cm) 9. / (6mm) Self-Auguring Screws () Tube of vinyl glue () 0000 Material You Will Need x x 6 (0x0x8 cm) Pressure-treated wood post (cut in two - 6 (9 cm) lengths). Tools You Will Need Cordless Drill Hammer Tape Measure Level Shovel 9 0 Not to Scale in (8 cm) 80 in (0 cm) in (0.5 cm) 8 General Information Read Instructions through carefully before beginning assembly. When assembling components, place on a non-abrasive surface (i.e. shipping box) to avoid scratching. We recommend an area approx 5 x 8 (.5m x.m) for unobstructed assembling. You should not need to use excessive force when assembling component. V./0097

2 STEP ONE Privacy Screen Assembly Layout the horizontal spindles with all the routed holes inline as shown and insert the vertical spindles through them. Insert the two horizontal rails onto the vertical spindles as shown. Excessive force should not be used. Finish the assembly by inserting the two posts onto the rail ends as shown. Note the tabs on the horizontal spindles; once inserted, the spindles will lock into place. Fasten the posts onto the horizontal rails using a total of eight screws through the pre-drilled holes on the post. The Camden Privacy Screen

3 S TEP T W O Slide the two post trim caps down the post as shown, followed by the two post caps. The trim caps can sit on the horizontal rail for now and the post cap pressure-fits into place. Apply a small amount of glue to the inside of the end cap as shown and insert onto the beam. Allow 0 seconds for the glue to set and a few more minutes to cure. Repeat for second beam. With a helper, align one of the beam against the posts as shown. The top of the beam should be at the same level as the bottom of the post caps and the overhang should be equal on both ends. Equal Overhang Equal Overhang The Camden Privacy Screen

4 STEP THREE Fasten the beam onto the posts using eight screws as shown (four at each post). Repeat steps for the second beam. Apply a small amount of glue around the post approximately inch (.5 cm) below the beams as shown. Slide the post trim caps against the beam and hold for 0 seconds until the glue sets. The Camden Privacy Screen

5 S TEP FOUR Wooden Posts Installation Insert the two xx6 (0 x0 x 9 cm) pressure treated wood posts into the bottom of the vinyl post until it bottoms out against the horizontal rail. Fasten with two screws each (not included). S TEP FIVE Install Privacy Screen into Ground Dig two, 8 (0 cm) Diameter x (60 cm) Deep holes on 76 (9 cm) Centers 8 in Dia. (0 cm) 76 in (9 cm) in (60 cm) The Camden Privacy Screen 5

6 S TEP FIVE With a helper, place the privacy screen posts into the holes and level it both vertically and horizontally. Note: for asthestics purposes, the screws on the posts should be facing away. To prevent the privacy screen from sinking, place a few blocks of wood below the bottom horizontal rail. The bottom horizontal rail should be (0.5 cm) off the ground. Backfill the holes with cement and allow it to set and cure. Screws on posts should face away Level (0.5 cm) Wood Blocks North America Toll Free Phone: United Kingdom Tel: ()