#11178 Providence ARBOR
|
|
- Colin Patrick
- 5 years ago
- Views:
Transcription
1 #11178 Providence ARBOR ASSEMBLY INSTRUCTIONS TOOLS NEEDED Drill with #2 Phillips Bit (recommended) or Phillips Screwdriver Ruler Hammer or Mallet ARBOR TOP ASSEMBLY (Refer to Drawing 1) (Make 2) On clean flat surface lay one 2 x 2 x 84 left post and one 2 x 2 x 84 right post with pilot holes for screws facing up and the routed holes for ⅞ x 1½ x 22 cross rails facing inward. Starting at the bottom insert one of the top/bottom rails in the first routed slot. Continue by inserting eight of the ⅞ x 1½ x 22 center rails. Slide the other post onto the opposite end of the cross rails (do not fasten at this time). Insert the ¼ x 1½ x 59½ vertical slats through the ⅞ x 1½ x 22 cross rails. When both vertical slats are in place, gently spread the end of the panel and press the other top/bottom rail onto the vertical slats. Firmly press cross rails between posts to ensure that the cross rails are completely inserted into each post. Fasten the posts to the cross rails using the 1¼ screws, snap the screw caps over the screw heads. ARBOR TOP ASSEMBLY (Refer to Drawing 2) With the screw caps on the side panels facing the outside of the arbor, set both side panels on there edge approximately 42" apart. Insert one of the ⅞ x 1 ½ x 16 corner brace pieces into the bottom side of the 1 ½ x 4 x 64 top rail. Working with the side closest to you, slide the 1 ½ x 4 x 64 top rail into the 4" slot on the top of the post. As you slide the top rail into its hole in the post, insert the corner brace into the ⅞ x 1 ½ hole routed in the post. Do the same procedure for opposite end of 64" rail. Flip arbor over and repeat for other 64" rail. The measurement from the longest peak of top rail to the outside of the 2 x 2 leg should be 9. Make sure measurement of top rail is correct on both sides. Using 1 ¼ screws fasten corner braces, top rail and side panels together, snap screw caps over screw heads. Lay the ⅞ x 1 ½ x 28 top cross rails into place on top of the top rails, using the pilot holes for screws as your guide. Fasten each top cross rails using 1 ¼ screws and snap screw caps over screw heads. FINISHING TOUCHES Apply glue to the inside edges of the 5 ⅜ end caps and push them onto the ends of the 64" rails; do not slide from ends. Apply glue to inside edges of the 2 x 2 post caps for arbor posts and the ⅞ x 1 ½ end caps for top cross rails on arbor top. Arbor is now ready for installation (See Ground Anchor Hardware Bag). If you encounter missing or defective parts, please contact manufacturer direct at toll free # below. Dura-Trel, Inc. ~ PO Box 122, Sheboygan Falls, WI ~ Toll Free
2
3
4 PACKING LIST #11178 Providence Arbor PARTS CONTAINED: QTY. PART NO. PART DESCRIPTION L 2 x 2 x 84 LEFT POST R 2 x 2 x 84 RIGHT POST ⅞ x 1½ x 22 TOP/BOTTOM RAIL ⅞ x 1½ x 22 CENTER RAIL ¼ x 1½ x 59½ SLAT ½ x 4 x 64 ARBOR TOP RAIL ⅞ x 1½ x 28 TOP CROSS RAIL ⅞ x 1½ x 16 CORNER BRACE 4 5ECAP ⅞ x 1½ x 5⅜ END CAP 1 HWBAG-22GAA GROUND ANCHOR HARDWARE BAG 1 7GLUE-2OZCN PVC GLUE Hardware Bags Includes: 4 7CAPS-0202P 2 x 2 POST CAP 14 7CAPS-7815E ⅞ x 1½ END CAP 38 7HDWR-K8125 1¼ KAPPET SCREW 38 7HDWR-K8000 KAPPET SCREW CAP 1 PROVIDENCE ARBOR INSTRUCTIONS NOTE: Some parts may be packed inside of others. If you encounter missing or defective parts, please contact manufacturer direct at toll free # below. Dura-Trel, Inc. ~ PO Box 122, Sheboygan Falls, WI ~ Toll Free
5 2 sq. post arbor ground anchor Assembly & installation Instructions Parts List: Description Qty 16 L-channel Ground Anchor 4 1 Self-tapping White-head Screws 8 Option 1 (soft ground) Slide one 16 steel L-channel ground anchor into bottom of each post. Slide ground anchor up to bottom cross rail. Using two 1 selftapping white-head screws per post, screw post to ground anchor (figure 1). When fastening, use one screw per side where ground anchor meets post. For added support fasten screws with at least two inches vertically between them. Option 2 (hard ground) Measure distances between posts and mark ground accordingly. Pound 16 steel L-channel ground anchors into ground according to measurements and basic layout (figure 2), leaving about 4 inches of ground anchor exposed. When pounding into ground, use block of wood to prevent ground anchor from bending. Slide arbor over ground anchors. Using two 1 self-tapping white-head screws per post screw post to ground anchor (figure 1). When fastening, use one screw per side where ground anchor meets post. For added support fasten screws with at least two inches vertically between them. Option 3 (permanent installation) FIGURE 1 Ground Anchor Assembly FIGURE 2 Ground Anchor Basic Installation Layout Measure distances between posts and mark ground accordingly. Dig holes 12 deep according to measurements and basic layout (figure 2). Fill with cement and place 16 steel L-channel ground anchors in wet cement. Be sure that ground anchors are straight and in accordance with measurements of arbor posts. Allow cement to dry. NOTE: There is very little room for error with this installation method. Slide arbor over ground anchors. Using two 1 self-tapping white-head screws per post screw post to ground anchor (figure 1). When fastening, use one screw per side where ground anchor meets post. For added support fasten screws with at least two inches vertically between them.
6
#11179 Wellington ARBOR
#11179 Wellington ARBOR Assembly INSTRUCTIONS TOOLS NEEDED Tape Measure Variable Speed Drill with #2 Phillips Bit (recommended) or Phillips Screwdriver Hammer or Mallet ARBOR SIDE PANEL ASSEMBLY (Refer
More information#11179 Wellington ARBOR
#11179 Wellington ARBOR Assembly INSTRUCTIONS TOOLS NEEDED Tape Measure Variable Speed Drill with #2 Phillips Bit (recommended) or Phillips Screwdriver Hammer or Mallet ARBOR SIDE PANEL ASSEMBLY (Refer
More informationWindsor Arbor. Parts List: General Information: Tools required: Assembly & installation Instructions
Windsor Arbor Assembly & installation Instructions Parts List: General Information:» Read through carefully before beginning assembly.» When assembling components, place on a clean, flat, non-abrasive
More informationQueensbrook Pergola. General Information. Tools Required. Model# Assembly Instructions. Qty
Queensbrook Pergola Model# 11301 Assembly Instructions General Information PLEASE READ THROUGH BEFORE BEGINNING ASSEMBLY. IMPORTANT: Check boxes for Contents Listed Check inside of parts as some parts
More informationThe Nantucket Legacy Arbor
SSEMLY INSTRUTIONS The Nantucket Legacy rbor Please read through before starting assembly. IMPORTNT: HEK THE INSIDE OF YOUR POSTS FOR LL MTERILS. heck ox for These ontents In. the Keystone event of missing
More information10x10 Trellis Pergola
0x0 Trellis Pergola ASSEMBLY GUIDE Ver.-007 Table of Contents PAGE 0x0 Trellis Pergola Introduction & Overview...................................................... Pergola Materials Overview..............................................................
More informationThe Newport Arbor ASSEMBLY INSTRUCTIONS. Material You Will Need (Not Included) 4 in x 4 in x 4 ft Pressure Treated Lumber (4)
ASSEMBLY INSTRUCTIONS in in / in / in 0 in in in in Please read through before starting assembly. IMPORTANT: CHECK THE INSIDE OF YOUR POSTS FOR ALL MATERIALS. Check Box for These Contents In the event
More informationCABINETRY Assembly Instructions
www.hdicabinetry.com Assembly Instructions TABLE OF CONTENTS Category Page(s) Section 1: Framed Series Base Cabinet Instructions Wall Cabinet Instructions Easy Reach Cabinet Instructions 1.01-1.04 1.05-1.06
More informationSECTION 19: Endwood Fusion Welded Gate Installation Guide
SECTION 19: Endwood Fusion Welded Gate Installation Guide ASSEMBLY AND INSTALLATION FOR: Fusion Welded Gates Gate Frame with Full Size Pickets Privacy & Board on Board California & Shadowbox Gate width
More informationLaminate Cabinet Installation Instructions
Laminate Cabinet Installation Instructions www.easygaragestorage.com/installation How To Use These Instructions Thank you for your purchase! Please read each step of this manual thoroughly to ensure proper
More information10x10 Trellis Pergola
0x0 Trellis Pergola ASSEMBLY GUIDE Ver.0-7 Table of Contents PAGE Introduction & Overview...................................................... Pergola Materials Overview..............................................................
More informationCottage Picket Gate. 6 in in in in
S S E M LY I N S T R U T I O N S www.newenglandarbors.com ottage Picket Gate 1.875 in 6 in 43.75 in 22.5 in 2 48.5 in Please read through before starting assembly. heck ox for These ontents (1 ox) In the
More informationL.L.Bean. Wooden Slat Bed
L.L.Bean Wooden Slat Bed Thank you for purchasing our Slat Bed. Assembly of this product requires A Phillips head screwdriver. We have found it helpful to have a second person present in at least one step
More informationThe Devonshire Arbor 85 in
ASSEMBLY INSTRUCTIONS in in in in in Please read through before starting assembly.. in IMPORTANT: CHECK THE INSIDE OF YOUR POSTS FOR ALL MATERIALS. Check Box for These Contents In the event of missing
More informationEASY-IN POOL STEP SYSTEM NE132
EASY-IN POOL STEP SYSTEM NE132 This instruction manual features multiple guides for the step unit components. 7939 EASY POOL STEP (NE113) FOR USE WITH: EASY-IN POOL STEP (NE126) 6492 PARTS & HARDWARE FOR
More informationHow To Measure Your Finished Opening
3000 Series Bifold Doors How To Measure Your Finished Opening MEASURE FROM RIGHT TO LEFT 2 PLACES (WIDTH) MEASURE FROM TOP TO BOTTOM 2 PLACES (HEIGHT) Tools Required for Assembly: Tools Needed: Phillips
More informationFigure 1. RAILING INSTALLATION The following instructions describe the installation of three types of railing sections: Line, Stair, and Angled
Veranda Railing System Veranda railing systems are designed to work with a number of different decking materials and surfaces. Before initiating any project, obtain a copy of your local building codes
More informationROCKWELL. Two Panel Door. Half X Door. Double X Door. Z Combination Door
ROCKWELL 4 in 1 DOOR Choose between four door styles with this Door Kit. Our versatile Rockwell Door Kit is very easy to assemble. All materials and hardware needed to assemble any of the four styles are
More informationThe Nantucket Legacy Arbor
ASSEMBLY INSTRUCTIONS 0. in 9 in 0. in 68 in 7 in in *Nantucket Legacy with Trim Kit Shown Above. Please read through before starting assembly. in 60 in 0 in 8 in IMPORTANT: CHECK THE INSIDE OF YOUR POSTS
More informationFive Column Half Height Rack Base Rack. (Shown with Tabletop)
Five Column Half Height Rack Base Rack (Shown with Tabletop) Congratulations! You have purchased the finest wine racking available anywhere. Properly assembled, these Vigilant wine racks will outlast even
More informationWine Rack Assembly Instructions. Ten Column Display Rack
Wine Rack Assembly Instructions Ten Column Display Rack Congratulations! You have purchased the finest wine racking available anywhere. Properly assembled, these Vigilant wine racks will outlast even your
More informationPlayground Assembly Instructions
Before You Begin Playground Assembly Instructions Locate the playground set on firm, level ground. Assemble the playground on or close to its permanent location Two people are recommended to assemble the
More informationWalk-in Configurations
Walk-in Configurations Includes Wall-to-Open, Corners, and Corner Rounder Bars INSTALLATION INSTRUCTIONS Tools needed: Tape measure, level, pencil, #2 Phillips head screw driver or power drill with a 6"
More informationRockwell 4-in-1 Sliding Door
Rockwell 4-in-1 Sliding Door ASSEMBLY INSTRUCTIONS ROCKWELL 4-IN-1 SLIDING DOOR Recommended Tools Drill with Phillips Bit Socket Wrench with 7/16 Socket Rubber Mallet Adjustable Square ROCKWELL 4-IN-1
More informationPVC Fencing Install Instructions
PVC Fencing Install Instructions Step 1-Pounding the Galvanized Steel Posts Call your local area utility company to come mark underground lines before any digging or pounding any posts into the ground.
More informationThe Westchester Arbor
A S S E M B LY I N S T R U C T I O N S 9. in 90 in. in 0 in in 0 in in Please read through before starting assembly. Check Box for These Contents In the event of missing or defective parts please call
More informationThe Camden Privacy Screen
ASSEMBLY INSTRUCTIONS The Camden Privacy Screen 0 5/8 in (66 cm) 7 / in (8 cm) 6 / in (6.5 cm) 90 in (9 cm) Post 66 in (68 cm) 78 in (98 cm) Please read through before starting assembly. IMPORTANT: CHECK
More informationO-Sullivan King 4 Poster Bed O-Sullivan Queen 4 Poster Bed Parts and Hardware List
Parts and Hardware List A. Left Headboard Post 1 pc B. Right Headboard Post 1 pc C. Left Footboard Post 1 pc D. Right Footboard Post 1 pc E. Headboard Panel 1 pc F. Footboard Rail 1 pc. Spindles 4 pcs
More informationHow to Install Custom Real Wood and Faux Wood Blinds
Before you begin your installation: READ ALL INSTALLATION INSTRUCTIONS! Make sure that you have all tools and hardware needed for installation. Check the installation surface (wall, ceiling, or window
More informationBeadboard Curved Bed Queen Size
Beadboard Curved Bed Queen Size PRE- ASSEMBLY: Remove all parts and hardware from the box, and lay them out on a carpeted or scratch-free work surface. The shipping box provides an ideal work surface,
More informationL.L.Bean. Platform Bed
L.L.Bean Platform Bed Thank you for purchasing our Platform Bed. Assembly of this product requires a Phillips head and a flat head screwdriver. We have found it helpful to have a second person present
More informationMount to the Wall INSTALLATION MANUAL
Mount to the Wall 15 Locate the Wooden Studs This step applies to wooden stud wall installation only. Determine and mark the exact locations of two stud centers on the wall. Wooden studs should be spaced
More informationFigure A. Figure B. Figure C. Figure D
Xsite 1 Power/Data Tile and Components Tools Required Tape Measure Cordless Drill/Driver #2 Phillips Screw driver bit Rubber Mallet Flat Blade Screwdriver Figure A Hardware Required Provided as shown Installation
More informationCottage Picket Gate A S S E M B LY I N S T R U C T I O N S
S S E M LY I N S T R U T I O N S ottage Picket Gate 1 7/8 6 43 3/4 22 1/2 48 1/2 Please read through before starting assembly. heck ox for These ontents (1 ox) In the event of missing or defective parts
More informationFor Wallbed models: KING SIZE INSTRUCTION BOOKLET #C1 Watch step by step installation instructions at: https://www.wallbedsbywilding.com/wallbed-installation-studio-series/ WARNING! ALL MURPHY/WALLBED
More informationAssembly Instructions
Unite Panel System Hinge Door July 2016 #12 x / slotted hex washer head bolt Figure 1 threshold bracket frame Detail F threshold bracket threshold bracket (installed) #12 x / slotted hex washer head bolt
More informationEquilibrium. Conference Table. Installation Instruction. Revision B 11/07/16
Equilibrium Conference Table Installation Instruction Revision B 11/07/16 Equilibrium End User Agreement Enwork Equilibrium table bases must be installed directly onto a four inch minimum thickness concrete
More informationINSTRUCTION BOOKLET #C20
INSTRUCTION BOOKLET #C0 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION PROCESS COULD RESULT IN SEVERE PERSONAL INJURY TO
More informationINSTRUCTION BOOKLET #C10 Watch step by step installation instructions at: https://www.wallbedsbywilding.com/wallbed-installation-studio-series/ WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY.
More informationInstallation Instructions for. Handrail Component System
Handrail STEP-BY-STEP Installation Instructions for Handrail Component System Rise in Inches Run in Inches 8 8.5 9 9.5 10 10.5 11 11.5 12 12.5 13 13.5 14 14.5 15 8.5 47 45 43 42 40 39 38 36 35 34 33 32
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS TOOLS REQUIRED Rechargeable, variable speed drill 3/8 diameter drill bit 3 Robertson bits #0, #1 and #2 Slot screwdriver Non marring hammer with 1 head Level Caulk or sealant
More informationDowntown Rack. Custom logo option available
Custom logo option available Downtown Rack The Downtown Rack uses thick, square-tube construction that can t be cut with a pipe cutter. The extended width of the Downtown Rack makes for easy bike parking
More informationTIP FOR GETTING STARTED
Tip for getting started TIP FOR GETTING STARTED Be careful not to drill into any electrical wires, ductwork, plumbing or other damagable components. If you have any questions on the locations of these
More informationINSTRUCTION BOOKLET #C21. For Wallbed models: KING SIZE
For Wallbed models: KING SIZE INSTRUCTION BOOKLET #C1 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION PROCESS COULD RESULT
More informationAssembly and Installation Guide
The Easy Hang Closet Solution SM Install Your elfa In An Instant. Enjoy The Benefits For A Lifetime. Basic Tools For elfa Assembly and Installation Level Hand or Power Drill Drill Bits 1/8", 3/8", 5/16"
More informationSwerve Rack CUSTOM RACKS AVAILABLE
CUSTOM RACKS AVAILABLE Swerve Rack The design of the Swerve mirrors the bike frame, thus providing superior bike support while making it easy to secure both the bike frame and wheel with a standard u-lock.
More informationOceanside Outdoor Vinyl Shower Kit (3 x 3 Enclosure)
Oceanside Outdoor Vinyl Shower Kit ( x Enclosure) A B ASSEMBLY GUIDE REQUIRED FOR INSTALLATION (A) Zippity Post Extension for In-Ground Installation (Sold as 4-Packs) (B) Zippity Galvanized Steel Surface
More informationQueen Wingback Bed King Wingback Bed
Parts and Hardware List A. Side Rails with Attachment Hooks 2 pcs B. Foot Rail 1 pc C. Head Rail 1 pc D. Center Support Slat 1 pc E. Leg Supports 3 pcs F. Support Slats 4 pcs G. Flat Washers 8 pcs H. Lock
More informationhttps://www.wallbedsbywilding.com/wallbed-installation-studio-series/
For Wallbed models: KING SIZE INSTRUCTION BOOKLET #C1 Watch step by step installation instructions at: https://www.wallbedsbywilding.com/wallbed-installation-studio-series/ WARNING! ALL MURPHY/WALLBED
More informationIMPORTANT: CHECK THE INSIDE OF THE LARGER PIECES IN YOUR BOX FOR OTHER MATERIALS PACKED INSIDE.
ASSEMBLY GUIDE Newport Vinyl Picket Fence with Post and No-Dig Steel Pipe Anchor Kit (6 H x 7 W) 68 / in /6 in 6 in / in 7/8 in 8 / in 6 in in Ground 4 in This fence can easily be trimmed down horizontally
More informationMISCELLANEOUS CABINET REPAIRS
MISCELLANEOUS CABINET REPAIRS 167 168 NOTES MISCELLANEOUS CABINET REPAIRS Cabinet Panel Repairs 175 SIDE PANEL REPLACEMENT - GDM SERIES INSTALLATION INSTRUCTIONS Tools Required 1/8" drill Rivet Tool Silicone
More informationSide Mount INSTRUCTION BOOKLET #C122 BED STYLE: PARK CITY
Side Mount BED STYLE: PARK CITY INSTRUCTION BOOKLET #C1 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION PROCESS COULD RESULT
More informationROCKWELL 4-IN-1 DOOR. Two Panel Door. Half X Door. Z Combination Door. Double X Door
ROCKWE 4-IN-1 DOOR Two Panel Door Half X Door Double X Door Z Combination Door Choose between four door styles with this Door Kit. Our versatile Rockwell Door Kit is very easy to assemble. All materials
More informationUNIVERSAL PANEL AND GATE
PVC Fencing / Residential Style UNIVERSAL PANEL AND GATE INSTALLATION INSTRUCTIONS Fencing Without Boundaries TM 1 BEFORE YOU START, IT S IMPORTANT TO CHECK......That fence footings do not exceed legally
More informationINSTRUCTION BOOKLET #C0 Watch step by step installation instructions at: https://www.wallbedsbywilding.com/wallbed-installation-studio-series/ WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY.
More informationO W N E R ' S M A N U A L
TABLE TENNIS TABLE MODEL NOS. T861 T861B O W N E R ' S M A N U A L 1. Read this manual carefully before starting assembly. Read each step completely before beginning each step.. Some smaller parts may
More informationAFCO-Rail Post INSTALLATION INSTRUCTIONS AFCO-RAIL POST
AFCO-Rail Post INSTALLATION INSTRUCTIONS TOOLS REQUIRED: Drill Bits (for the appropriate fastener) Drill (with adjustable clutch, recommended) Level String Line Tape Measure Tools to install fasteners
More informationResidential & Industrial Fence
Page Residential & Industrial Fence Assembly Instructions Congratulations on the purchase of your new Fence System. Your fence has been designed to give you years of trouble free service with only minimal
More informationMAINSTREET 36 INCH TABLE SOCCER
Mainstreet 36 Inch Table Soccer MAINSTREET 36 INCH TABLE SOCCER Replacement Parts Order direct at or call our Customer Service department at (800) 5-7593 8 am to 4:30 pm Central Standard Time September
More informationPLEATED SHADE ARCH INSIDE MOUNT GETTING STARTED. A few simple tools are required: STANDARD HARDWARE
HONEYCOMB AND PLEATED SHADE ARCH GETTING STARTED INSIDE MOUNT A few simple tools are required: HALF ARCH INSTALLATION Your half arch has been shipped in the closed osition. When fanned, the rails will
More informationBaby Grande with Crank, Housing, and Side Rails Installation Instructions
Baby Grande with Crank, Housing, and Side Rails Installation Instructions Tools Needed Hardware Provided (per shade) Hardware Needed Drill 3/8 Metal Drill Bit ¼ Masonry Drill Bit Measuring Tape Pencil
More informationClearview Railing System Installation Instructions
Clearview Railing System Installation Instructions Disclaimer: AGS Stainless, Inc. has its Clearview Railing Systems designed by a professional engineer to meet the requirements of the latest national
More informationCOCKPIT CORNER UNIT WARNING. Illustration 1. Read all instructions and review illustrations before installing. Tools required for assembly:
Illustration 1 Illustration 2 Right side of Illustration 3 Right brace Right brace Read all instructions and review illustrations before installing. Tools required for assembly: Phillips screwdriver Rubber
More informationMotorized or Crank Operated Fortress Zipper Track Shade with Housing and Side Track Installation Instructions
Motorized or Crank Operated Fortress Zipper Track Shade with Housing and Side Track Installation Instructions Tools Needed Drill 3/8 Metal Drill Bit ¼ Masonry Drill Bit Measuring Tape Pencil 4 Level Phillips
More informationCABLE COVER ORGANIZER KIT USER GUIDE AND INSTALLATION INSTRUCTIONS
CABLE COVER ORGANIZER KIT USER GUIDE AND INSTALLATION INSTRUCTIONS TOPIC PAGE Applications, Specifications, Warnings and Cautions 2 Kit Contents 3 Installation Instructions Painting. 4 Layout Preparation...
More informationAssembly Instructions
RoomScape Furniture System March 2013 - Bed Styles bed deck board bed deck board top cap top cap base glide middle side rail frame frame stacking device frame middle lower reinforcement side rail Single
More informationThe Cambridge Raised Planter Extension Kit
ASSEMBLY INSTRUCTIONS The Cambridge Raised Planter Extension Kit www.newenglandarbors.com www.newenglandarbors.co.uk in (0 cm) 8 in ( cm). in (90 cm). in (8 cm). in (8 cm) 8. in ( cm) 9 in ( cm) Please
More informationArtisan Vinyl Pergola
Artisan Vinyl Pergola Assembly Manual Thank you for your purchase of this Pergola. Beefy Vinyl Pergola Assembly Manual This manual is designed to simplify the assembly process, however we recommend having
More informationThe Vienna Trellis. Tools You Will Need. General Information
A S S E M B LY I N S T R U C T I O N S www.newenglandarbors.com 8.7 in 9 in 6 in in Please read through before starting assembly. in 9 in IMPORTANT: CHECK THE INSIDE OF YOUR POSTS FOR ALL MATERIALS. Check
More informationSAVE THESE INSTRUCTIONS
SAVE THESE INSTRUCTIONS DEALER/INSTALLER: GIVE TO HOMEOWNER OCEAN BLUE GRAND ENTRANCE POOL STEPS ASSEMBLY AND INSTALLATION MANUAL ABOVE GROUND FOUR TREAD MODEL Part No. 400700 IN GROUND THREE TREAD MODEL
More informationRemoving and Replacing the Y-truck
Service Documentation Removing and Replacing the Y-truck To remove and replace the Y-truck you will need the following tools: 4mm Allen wrench 12mm stamped flat wrench #2 Phillips screwdriver (magnetic
More informationPROTECT-A-POOL INGROUND REMOVABLE SAFETY FENCE
PROTECT-A-POOL INGROUND REMOVABLE SAFETY FENCE I N S T A L L A T I O N I N S T R U C T I O N S INSTALLATION TOOLS The following tools are required for installation. Chalk Pencil Utility Knife Tape Measure
More informationFLEX 48 x 72 / 60 x 72
FLEX 48 x 72 / 60 x 72 SHOWER DOOR INSTALLATION INSTRUCTIONS IMPORTANT DreamLine reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical
More informationBuilding Your Faith Chest
Building Your Faith Chest You will need the following tools: 1 Phillips screwdriver Hammer Wood Glue (optional) Sanding Block (optional) Tape Measure (optional) Step 1: Step 2: Step 3: Step 4: Step 5:
More informationHOW TO INSTALL HORIZONTAL ROD RAILING TREX SIGNATURE STANDARD
HOW TO INSTALL HORIZONTAL ROD RAILING NOTES:» Adjust drill power to lowest setting that will drive screw. DO NOT OVER TORQUE 6 STAINLESS STEEL STAINLESS FASTENERS.» NEVER use impact tools on 6 Stainless
More informationSLIM TRIM MOULDING INSTALLATION METHODS
Slim Trim as a reducer Use SlimTrack (Metal Track) for up to 4 mm floors. Up to 4 mm Floors 3/8 *If the flooring manufacturer suggests/permits the use of underlayments you may need to shim the track to
More informationGREENHOUSE 6'x8' ASSEMBLY INSTRUCTIONS. (Internal Dimensions) Overall Dimensions (Approx.) L 193 W 200 H cms 97.5" L 76" W 78.
ASSEMBLY INSTRUCTIONS GREENHOUSE 'x8' (Internal Dimensions) Overall Dimensions (Approx.) 7. L 9 W 00 H cms 97." L 7" W 78.8" H 0 IMPORTANT You must read these instructions carefully before you start to
More informationPRO-RIB FENCE PANELS INSTALLATION GUIDELINES. Virtually Maintenance Free Available in 24 Colors Custom Heights Available by the Inch
PRO-RIB FENCE PANELS INSTALLATION GUIDELINES Virtually Maintenance Free Available in 24 Colors Custom Heights Available by the Inch www.midwestmanufacturing.com Page 2 TOOLS NEEDED Measuring Tape Drill
More informationAssembly Instructions
18' W x 10' H or 12' H Peak Style Frame Assembly Assembly Instructions Before you start: 2+ individuals recommended for assembly, approximate time 3 hours. Recommended tools: Power Drill, Safety Glasses,
More informationTREX REVEAL RAILING Installation Instructions
TREX REVEAL RAILING BRACKET HARDWARE STAIR APPLICATIONS (INCLUDING STAIR SWIVEL BRACKETS, STAIR CROSSOVER BRACKET, AND COMPOUND SWIVEL BRACKETS) FIXED BRACKET Stair HARDWARE AA. Bottom Stair Bracket and
More informationResidential & Industrial Fence
Residential & Industrial Fence Assembly Instructions CONTENTS 02: OVERVIEW & CONTENTS 03: PRODUCT SPECIFICATIONS 04: GETTING STARTED 05: WALL ATTACHMENT & LINE POST ASSEMBLY 06: CORNER POST ASSEMBLY 07:
More informationGambrel Barn Construction Manual 8x8 through 16x24 Units
Gambrel Barn Construction Manual 8x8 through 16x24 Units Tools Needed: Cordless drill (12V or higher) #2 square drive bit Hammer 6 step ladder Tape measure Square utility knife w/ blade & hook blade Little
More informationWARM SHAKER / NORFOLK / LEXINGTON TV MEDIA STAND
SIMP II H O M E L I F E Y D E S I GN WARM SHAKER / NORFOLK / LEXINGTON TV MEDIA STAND 1/21 FOR REPLACEMENT PARTS OR HELP WITH ASSEMLY PLEASE CONTACT US AT: simpli-home.com/customer-support PLEASE ENSURE
More informationInstallation Instructions for. Before You Begin TOOLS REQUIRED
Composite Railing System STEP-BY-STEP Installation Instructions for Spectrum Composite Railing Virtually maintenance free 20-year warranty EverNew Spectrum Railing system is designed to work with a number
More informationRAILING R A IL ING 51
RAILING RAILING 5 TREX TRANSCEND RAILING NOTES:» TREX TRANSCEND RAILINGS ARE DESIGNED TO BE INSTALLED OVER THE DECKING FRAME OR ON INSIDE OF RIM JOIST. NOTCHING OF PRESSURE-TREATED POSTS OR POSTS INSTALLED
More informationALL SEASON PATIO COVER
ALL SEASON PATIO COVER 61 Where the All Season Patio Cover is to be attached to the home, create a level line showing where the top of the mounting rail is to be located. Install each section with the
More informationSentinel Series Cigar Humidor End Tables
Sentinel Series Cigar Humidor End Tables Assembly Instructions Models: Sentinel 500, 1000 and 1500 Style: Contemporary SENTINEL ASSEMBLY INSTRUCTIONS Congratulations! You have purchased a superior cigar
More informationUnder Seat Storage Drawer Installation Instructions
Under Seat Storage Drawer Installation Instructions Parts List: 1) Drawer Assembly 8) Self Tapping Screws 1) Instructions 1) Template Tools Needed: Drill and/or Bit Driver Tape Measure Jigsaw or metal
More informationThe Festival Assembly Instructions
The Festival Assembly Instructions Toll Free: 866.768.8465 Hours: 9-5 Monday-Friday EST www.homeplacestructures.com Package ships as shown CONTACT INFORMATION: HomePlace Structures 301 Commerce Drive New
More informationInstallation Instructions
Installation Instructions For Models: Model Number / Description File Name 1540 Classic Series P-Lam Toilet Partitions 1540.pdf 1 INSTALLATION INSTRUCTIONS LAMINATED PLASTIC TOILET PARTITIONS 1540 Classic
More informationGROWING BETTER THROUGH DESIGN. 6ft Lean-To LEAN-TO. Assembly Instructions 04/02
GROWING BETTER THROUGH DESIGN 6ft Lean-To LEAN-TO Assembly Instructions 04/02 6ft Lean-To Greenhouse Base Plan Introduction/Tools/Contents / / Contents This is a copy of our Lean-To greenhouse base plan.
More informationOWNER S MANUAL Table Tennis Table Patent Pending
OWNER S MANUAL Table Tennis Table Patent Pending Be sure to write your model number and serial number here for future reference. You can find these numbers printed on the bottom of the table. MODEL # T8266
More informationRipple Hanger ASSEMBLY INSTRUCTIONS
Ripple Hanger ASSEMBLY INSTRUCTIONS RIPPLE HANGER Recommended Tools Drill with 1/8, 1/4, and 1/2 Drill Bits, 1-1/8 Forstner Bit or 1-1/8 Spade Bit, and Phillips Bit 9/16 and 5/8 Combination Wrench Socket
More informationSHADOWBOX INSTALLATION FOR: Standard 6 H x 8 W Shadowbox Fence 5 x 5 Routed Posts Dog Ear or Straight-Edge Pickets 1.75 x 3.5 Rail
SHADOWBOX INSTALLATION FOR: Standard 6 H x 8 W Shadowbox Fence 5 x 5 Routed Posts Dog Ear or Straight-Edge Pickets 1.75 x 3.5 Rail Storage and Handling Fence Preparation and Layout Locate and Set Posts
More informationSTACKING MULTI-SLIDE DOOR SYSTEM INSTALLATION INSTRUCTIONS
STACKING MULTI-SLIDE DOOR SYSTEM INSTALLATION INSTRUCTIONS 1290363 Revision 1 12/16 Page 1 Weather Shield Mfg., Inc. NOTICE CAUTION! Failure to install and maintain our product according to these instructions
More informationTREX REVEAL RAILING Installation Instructions
TREX REVEAL RAILING NoteS:» Reveal railings are designed to be attached with posts installed at a clear span of 6' (.8 m) or 8' (.44 m).» If installing at exact span lengths of 6' (.8 m) or 8' (.44 m),
More informationTrack Rack. * Track Racks are not lockable
The Track Rack s unique staggered, sliding hook design creates the greatest parking efficiency while still providing easy access to any particular bike. When adding or removing a bike to the rack, simply
More information3 D Printer Enclosure Assembly Instructions
3 D Printer Enclosure Assembly Instructions Tools Required: 2.5 mm Allen wrench (included) Phillips screwdriver Adjustable Wrench Parts Included: Plexiglas Back with fan and filters installed (29.5 x 35.5
More informationTHE PODIUM MUSIC STAND
THE PODIUM MUSIC STAND 1 Set Assembly Instructions Wooden Parts: a. 1 Column b. 2 Long Slide Pieces c. 2 Slide Spacers (1 long & 1 short) d. 4 Feet e. 2 Fork Pieces f. 1 Fork Spacer g. 2 Long Desk Frame
More informationAssembly Instructions COMO Double Bed
Assembly Instructions COMO Double Bed VER 1.2 WARNING NG FAILURE TO FOLLOW THESE BASIC STEPS CAN LEAD TO DAMAGE THAT IS NOT COVERED BY YOUR WARRANTY 2 Read Instructions carefully. Check no parts are missing.
More information