installation guide ICON classic benching

Size: px
Start display at page:

Download "installation guide ICON classic benching"

Transcription

1 installation guide ICON classic benching

2 Index ICON Installation Guide Single Run Frame Assembly... Worksurfaces and Electrical... Attaching Worksurfaces to Frame...6 Installing optional accessories...7 Installing Screens...8 Jumpers...9 Power Pole...0 Double Run Frame Assembly... Worksurfaces and Electrical... Attaching Worksurfaces to Frame... Installing optional accessories... Installing Screens and Remaining Worksurfaces...6 Jumpers...7 Power Pole...8 Modesty Panel...9 P

3 ICON installation guide SINGLE RUN P

4 Phase Frame Assembly ICON Single Run Installation Guide Screw the outer-to-inner horizontal beams (H-bar) to the top of each outside leg (O-Leg) using the M8* screws. Then screw the outer-to-inner H-bars to the bottom of each O-Leg using the M6*0 screws. Adjust the glides to level the frame as needed. We suggest using a leveling glide for best accuracy. Rest the outer-to-inner H-bars on the top of the inner legs (U-Leg). Then rest the inner-to-inner H-bars on top the U-legs. Screw the horizontal beam connectors and H-bars to the frame using the M6*0 screws. Bottom screws should be installed first on all frame bars. NOTE: For 60 or 7 ICON frame bars the bars should be aligned so that the large oval hole is located on the inside of the bench to accommodate future returns. P

5 Phase Assembling Worksurfaces and Electrical ICON Single Run Installation Guide Lay the worksurfaces face down in a row. Screw the troughs onto all the worksurfaces using lath screws. It is recommended that troughs be placed in the center inches from the back edge of the worksurface. Snap duplexes into each of the junction blocks. Clip H-brackets to each of the junction blocks. Then snap the junction blocks into each of the trough cut outs. Screw the H-brackets directly into the troughs and worksurfaces using self-tappers. Place in center, from the back edge of the worksurface. P

6 Phase Attaching Worksurfaces to Frame ICON Single Run Installation Guide Rest the completed worksurfaces on top of the frame, starting from the outer worksurfaces working towards the center. Use a clamp to temporarily hold the worksurfaces together until they are ready to be permanently screwed to the frame. If needed, adjust the frame width to open or close the gap between the worksurfaces using a rubber mallet. 6 Screw all worksurfaces to the H-bars along the center of the frame using counter-sunk screws. Screw the worksurfaces together using a mending plate using counter-sunk screws. 6 Once everything is properly aligned, screw the outer worksurfaces to the frame using the counter-sunk screws. Make sure worksurfaces are evenly flush to the frame. P6

7 Phase Installing Optional Accessories ICON Single Run Installation Guide Power Box: Take the Power Box and place it on the desired location on the back edge of the worksurface. Secure to worksurface using tightening bolt. Monitor Arm Installation: We recommend to install a monitor arm equipped with clamp mount along the back edge of the worksurface. Please follow the recommended manufacturer instructions provided with your monitor arm. P7

8 Phase Installing Screens ICON Single Run Installation Guide STOP If you are installing a glass screen skip Step and continue on to Step. Take the fabric screens and measure the desired location of the screen clips and tighten using tightening screws. Be sure to use leveling guide to make sure the clips are leveled on each side. Make adjustments as needed. Skip Step and continue on to Step. * Clip kit includes fit-sleeve for glass screen. Insert glass fit-sleeve into the screen clips. Attach the clips to the glass screen with the tightening screws. Slide the screen clips onto the worksurface. Tighten to the worksurface using the hand-knob screw. To tighten screens, tighten the inside screw using an allen wrench. Fabric Screen Glass Screen P8

9 Phase 6 Installing Jumpers ICON Single Run Installation Guide Connect junction blocks to jumpers. Screw conduit mounting brackets to the worksurfaces using the counter-sunk screws STOP The remaining installation of electrical must be installed by a professional electrician. If you are installing a Power Pole continue on to Phase 7. P9

10 Phase 7 Installing a Power Pole ICON Single Run Installation Guide Make sure ceiling is prepped for the power pole location. You can use the ceilng cover as a guide to determine how big a cut out you need. Screw the power pole (pp) brackets to the top and bottom of the O-leg using self-tappers. Lay your pp on the floor and feed the ceiling feed through the bottom cutout of the pp. Loose wires should be at the top. Place the ceiling cover on the top of the pp. Lift the pp up and screw into pp brackets. Connect jumper to ceiling feed. Use the ceiling cover to secure pp to the ceiling. STOP The remaining installation of electrical must be installed by a professional electrician. * Use ceiling cover to secure pole to the ceiling. * Use self-tapping screw for attaching pole to leg beams. P0

11 Phase Frame Assembly ICON Single Run Installation Guide ICON installation guide DOUBLE RUN P

12 Phase Frame Assembly ICON Double Run Installation Guide Screw the outer-to-inner horizontal beams (H-bar) to the top of each outside leg (O-Leg) using the M8* screws. Then screw the outer-to-inner H-bars to the bottom of each O-Leg using the M6*0 screws. Rest the outer-to-inner H-bars on the top of the inner legs (U-Leg). Then rest the inner-to-inner H-bars on top the U-legs. Screw the horizontal beam connectors and H-bars to the frame using the M6*0 screws. Screw in the H-bar brackets to the U-legs using the M6* screws. Screw the round supports to the O-legs using the M6*0 screws. Adjust the glides to level the frame as needed. We suggest using a leveling glide for better accuracy. Bottom screws should be installed first on all frame bars. NOTE: For 60 or 7 ICON frame bars the bars should be aligned so that the large oval hole is located on the inside of the bench to accommodate future returns. P

13 Phase Assembling Worksurfaces and Electrical ICON Double Run Installation Guide Lay the worksurfaces face down in equal rows. Screw the troughs onto all the worksurfaces using lath screws. It is recommended that troughs be placed in the center inches from the back edge of the worksurface. Snap duplexes into each of the junction blocks. Clip H-brackets to each of the junction blocks. Then snap the junction blocks into each of the trough cut outs. Screw the H-brackets directly into the troughs and worksurfaces using self-tappers. P

14 Phase Attaching Worksurfaces to Frame ICON Double Run Installation Guide Rest the completed worksurfaces on top of one side of the frame, starting from the outer worksurfaces working towards the center. Use a clamp to temporarily hold the worksurfaces together until they are ready to be permanently screwed to the frame. If needed, adjust the frame width to open or close the gap between the worksurfaces using a rubber mallet. 6 7 Screw all worksurfaces to the H-bars along the center of the frame using counter-sunck screws. Screw the worksurfaces together using a mending plate using counter-sunk screws. Screw the worksurfaces to the H-braket located on the U-legs using the counter-sunk screws. 6 Once everything is properly aligned, screw the outer worksurfaces to the frame using the counter-sunk screws. Make sure worksurfaces are evenly flush to the frame. 7 Tip: Make sure H-bracket is inches from the back edge of the center worksurface to help ensure that the frame is straight. P

15 Phase Installing Optional Accessories ICON Double Run Installation Guide Power Box:Take the Power Box and place it on the desired location on the back edge of the worksurface. Secure to worksurface using tightening bolt. Monitor Arm Installation: We recommend to install a monitor arm equipped with clamp mount along the back edge of the workurface. Please follow the recommended manufacturer instructions provided with your monitor arm. P

16 Phase Installing Screens and Remaining Worksurfaces ICON Double Run Installation Guide STOP If you are installing a glass screen skip Step and continue on to Step. * Clip kit includes fit-sleeve for Glass screen. Take the fabric screens and measure the desired location of the screen clips and tighten using tightening screws. Be sure to use leveling guide to make sure the clips are leveled on each side. Make adjustments as needed. Skip Step and continue on to Step. Insert glass fit-sleeve into the screen clips. Attach the clips to the glass screen with the tightening screws. Slide the screen clips onto the worksurface. Tighten to the worksurface using the hand-knob screw. To tighten screens, tighten the inside screw using an allen wrench. Repeat Phase ; Steps -7 for installation of remaining worksurfaces. Fabric Screen Glass Screen P6

17 Phase 6 Installing Jumpers ICON Double Run Installation Guide Connect junction blocks to jumpers, looping the last jumper at the end of the run to connect to opposite side and continue. Screw conduit mounting brackets to the worksurfaces using the counter-sunk screws STOP The remaining installation of electrical must be installed by a professional electrician. If you are installing a Power Pole continue on to Phase 7. P7

18 Phase 7 Installing a Power Pole ICON Double Run Installation Guide Make sure ceiling is prepped for the power pole location. You can use the ceiling cover as a guide to determine how big a cut out you need. Screw the power pole (pp) brackets to the top and bottom of the O-leg using self-tappers. Lift the pp up and screw into pp brackets. STOP The remaining installation of electrical must be installed by a professional electrician. Lay your pp on the floor and feed the ceiling feed through the bottom cutout of the pp. Loose wires should be at the top. Place the ceiling cover on the top of the pp. Connect jumper to ceiling feed. Use the ceiling cover to secure pp to the ceiling. * Use ceiling cover to secure pole to the ceiling. * Use self-tapping screw for attaching pole to leg beams. P8

19 Phase ICON Modesty Panel Installation Guide Locate the four pilot holes on the board and attach four brackets using M wood screws. Place the assembly from previous step inside the leg s opened profile. Mx0 Self tapping screw x Using M self-tapping screws, attach the assembly onto the leg frame. Connector x pcs Mx Wood screw x Isle Side Leg side P9

20 Day Open Plan we provide exceptional experiences with reliable, easy interactions and successfully fulfilled orders in only days 9 Walsh Avenue / Santa Clara, CA 900 (877) amqsolutions.com

Footer & Base Plate Assembly. installation guide. ILINE power/data beam

Footer & Base Plate Assembly. installation guide. ILINE power/data beam Phase Footer & Base Plate Assembly installation guide ILINE power/data beam Phase Materials and Tools. ILINE Postsleeve Components Top Cap Data Face Plate Post Sleeve Post Sleeves shipped with orders after

More information

installation guide Footer & Base Plate Assembly KINEX Installation Guide SINGLE RUN

installation guide Footer & Base Plate Assembly KINEX Installation Guide SINGLE RUN Phase Footer & Base Plate Assembly KINEX Installation Guide SINGLE RUN KINEXbenching installation guide Please contact cc@amqsolutions.com if you are missing any parts, have difficulty with assembly, or

More information

KINEX benching Installation Guide

KINEX benching Installation Guide KINEX benching Installation Guide Index KINEX Installation Guide SINGLE RUN SINGLE RUN Assembly Components... Assembly Outline...5 DOUBLE RUN Assembly Components...8 Assembly Outline...9 Assembly Instructions

More information

compile system INSTALLATION GUIDE Updated January 2019

compile system INSTALLATION GUIDE Updated January 2019 INSTALLATION GUIDE Updated January 09 compile system Table of Contents Panels 0 Quick Connect Clips 0 Lock Clips 0 Panel Trims 0 Privacy Glass 0 Post Base Covers 04 Electrical 04 Power Distribution Harness

More information

OXYGEN INSTALLATION. Revision date

OXYGEN INSTALLATION. Revision date 12345 1 Hardware List 12345 Flat head wood screw #9 x 7/8 long with #2 Phillips drive, silver Used to attach surfaces and end panels Hex set screw ½-13 x 2 long with 1/4 hex drive, black Used on Legs Hex

More information

Assembly Instructions

Assembly Instructions InTandem Table System November 20 InTandem Table System - Worksurface #4 x/" 4 wood screw power beam Tools Provided T-0 Extended Torx Driver T-25 Torx Driver Additional Tools Required Soft protective

More information

Assembly Instructions & General Overview

Assembly Instructions & General Overview Assembly Instructions & General Overview 1. General Overview & Assembly Order...Page 3 2. Assembling the Structural Components Page 4-11 3. Power, Data, Power Poles and Cable Floor Boxes.Page 12-17 4.

More information

bridges Installation Manual

bridges Installation Manual bridges Installation Manual 0 OHSAS 800:007 CGSB #0HS-009 ISO 900:008 CGSB #96- ISO 00:00 CGSB #EMS-00 Global Contract Inc. 6 Petrolia Road North York, Ontario, MJ X8 Visit us on the Internet at globalcontract.com

More information

STAKS BENCHING ASSEMBLY INSTRUCTIONS

STAKS BENCHING ASSEMBLY INSTRUCTIONS STAKS BENCHING ASSEMBLY INSTRUCTIONS TABLE OF CONTENTS BASE ASSEMBLY 3 ORGANIZER INSTALLATION 4-5 PRIVACY SCREEN INSTALLATION 6 WORKSURFACE INSTALLATION 7 TOP STRAP INSTALLATION 8-9 POWER INSTALLATION

More information

13MM FLAT WRENCH FOR LEVELING THE GLIDES OF STRUCTURE 6MM ALLEN KEY FOR ROOF CLIPS PHILLIPS HEAD BIT FOR SCREWS FOR DOOR FRAME

13MM FLAT WRENCH FOR LEVELING THE GLIDES OF STRUCTURE 6MM ALLEN KEY FOR ROOF CLIPS PHILLIPS HEAD BIT FOR SCREWS FOR DOOR FRAME 1 TOOLS REQUIRED: MOVING CART/DOLLY FOR TRANSPORTING PANELS, ROOF, AND POSTS TWO 9 FT. STEP LADDERS FOR INSTALLING ROOF & PANELS REVERSIBLE RATCHET 1/4 DRIVE FOR CORNER SCREWS ON TOP TRAVERSE BEAMS ALTERNATIVE

More information

TOOLS REQUIRED: HARDWARE INCLUDED: 13MM FLAT WRENCH FOR LEVELING THE STRUCTURE RATCHET WITH 5MM HEX BIT FOR CORNER SCREWS ON TOP TRAVERSE BEAMS

TOOLS REQUIRED: HARDWARE INCLUDED: 13MM FLAT WRENCH FOR LEVELING THE STRUCTURE RATCHET WITH 5MM HEX BIT FOR CORNER SCREWS ON TOP TRAVERSE BEAMS 1 TOOLS REQUIRED: RATCHET WITH 5MM HEX BIT FOR CORNER SCREWS ON TOP TRAVERSE BEAMS 13MM FLAT WRENCH FOR LEVELING THE STRUCTURE RUBBER MALLET FOR INSERTING PANELS 8MM HEX BIT WITH EXTENSION FOR HEX BOLT

More information

6MM ALLEN KEY FOR ROOF CLIPS PHILLIPS HEAD BIT FOR SCREWS FOR DOOR FRAME SPIRIT/LASER LEVEL TO LEVEL THE UNIT

6MM ALLEN KEY FOR ROOF CLIPS PHILLIPS HEAD BIT FOR SCREWS FOR DOOR FRAME SPIRIT/LASER LEVEL TO LEVEL THE UNIT 1 TOOLS REQUIRED: MOVING CART/DOLLY FOR TRANSPORTING PANELS, ROOF, AND POSTS TWO 9 FT. STEP LADDERS FOR INSTALLING ROOF & PANELS MINI REVERSIBLE RATCHET 1/4 DRIVE FOR CORNER SCREWS ON TOP TRAVERSE BEAMS

More information

INSTALLATION MANUAL VERITY. friant.com/verity

INSTALLATION MANUAL VERITY. friant.com/verity INSTLLTION MNUL VERITY friant.com/verity 2 VERITY INSTLLTION MNUL General Information... 4 Safety & Support... 5 Installation Tools... 6 Staging & Installation... 7 Stand lone Units Single-Sided Structure...

More information

Bridges II Installation Guide. Effective June 2017 DESIGN GUIDE

Bridges II Installation Guide. Effective June 2017 DESIGN GUIDE Bridges II Installation Guide Effective June 07 DESIGN GUIDE Structure and Worksurfaces Beam Applications Supporting Structure Legs and Beams Telescopic Beam 0 Leg Storage Table Beam Sliding Return Round

More information

Figure A. Figure B. Figure C. Figure D

Figure A. Figure B. Figure C. Figure D Xsite 1 Power/Data Tile and Components Tools Required Tape Measure Cordless Drill/Driver #2 Phillips Screw driver bit Rubber Mallet Flat Blade Screwdriver Figure A Hardware Required Provided as shown Installation

More information

ELEVEN COLLABORATIVE. CONFERENCE TOPS Assembly Instructions

ELEVEN COLLABORATIVE. CONFERENCE TOPS Assembly Instructions ELEVEN COLLABORATIVE Table of Contents SUPPORT BRACE ASSEMBLY.... 3 TABLE BASE FRAME ASSEMBLY.... 4 LEG ATTACHMENT.... 5 TOP JOINING PLATE ASSEMBLY... 6 TOP CLAMP/TOP SPACER INSTALLATION.... 7 TOP PLACEMENT

More information

IMPULSE G2/PULSE STATIC BRIDGE & RETURN MODULE. Drill. Desk Connecting. Outside by fastening the supplied wood screws from the HK-67 kit through the

IMPULSE G2/PULSE STATIC BRIDGE & RETURN MODULE. Drill. Desk Connecting. Outside by fastening the supplied wood screws from the HK-67 kit through the PART # 1608990 STATIC BRIDGE & RETURN MODULE 1. This sheet covers the steps to install a static bridge or return module with the FX no hinged access panel back option to a height adjustable freestanding

More information

RANGE DIGITAL HANDSET OPERATION. 1. Panel. 2. Initialization Procedure. 3. Move Up & Down. 4. Set Memory Positions. 5. Move to the Memorized Positions

RANGE DIGITAL HANDSET OPERATION. 1. Panel. 2. Initialization Procedure. 3. Move Up & Down. 4. Set Memory Positions. 5. Move to the Memorized Positions INSTRUCTION SHEET #2577INS PART #1730534 DIGITAL HANDSET OPERATION OPERATION INSTRUCTIONS 1. Panel 1 Button: Preset 1 2 Button: Preset 2 3 Button: Preset 3 S Button: Select Display: Reads in 1 / 2 " Increments

More information

Range height adjustable assembly

Range height adjustable assembly Table of contents Digital handset operation 3 Height adjustable bench kit 4-5 Cable carrier 6 Ganging tray and ganging rail 7 Height adjustable return frame kit 8 Cable entry pole 9 24 and 30 d worksurfaces

More information

Compile Installation Manual

Compile Installation Manual Compile Installation Manual 07 OHSAS 800:007 ISO 900:05 ISO 400:05 Global Contract Inc. 565 Petrolia Road REVISED: FALL 07 North York, Ontario, MJ X8 Visit us on the Internet at globalcontract.com (46)

More information

a.k.a. casegoods instructions

a.k.a. casegoods instructions a.k.a. casegoods instructions a a.k.a. workwall installation IMPORTANT NOTES Failure to install product according to installation instruction will result in loss of warranty. Tools required for assembly

More information

Hover. Installation Instructions. Raised Panel. Version

Hover. Installation Instructions. Raised Panel. Version Installation Instructions Version 8-2-17 Raised Panel Table of Contents Page Raised Panel Trough 3-13 Platform Trough 14-20 Platform 120 Degree Trough 21-24 Electrical 25-28 Type A Electric Bases 29-31

More information

INSTALLATION MANUAL DASH. friant.com/dash

INSTALLATION MANUAL DASH. friant.com/dash INSTALLATION MANUAL DASH friant.com/dash 2 DASH INSTALLATION MANUAL General Information... 4 Safety & Support... 5 Installation Tools... 6 Staging & Installation... 7 Tabletops Freestanding Tabletops...

More information

Interra Installation Manual

Interra Installation Manual Interra Installation Manual Instructions to install the Friant Interra panel system Friant & Associates, LLC Table of Contents Getting Started Introduction... 3 General Tools, Staging & Safety... 4 Before

More information

MantelMount. TM1A Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS

MantelMount. TM1A Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS MantelMount TMA Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS TM Thank you for choosing the MantelMount television wall mount. Please read this entire manual before

More information

ROS-APT Caucus Plinth Table with Trough Note: Details apply, however the actual configuration of your table may vary from what is depicted here.

ROS-APT Caucus Plinth Table with Trough Note: Details apply, however the actual configuration of your table may vary from what is depicted here. ROS-APT Caucus Plinth Table with Trough Note: Details apply, however the actual configuration of your table may vary from what is depicted here. Parts List - Tables Tops, Top Insert Panels and Base panels

More information

Assembly Instructions. Table of Contents

Assembly Instructions. Table of Contents HQ Little Foot Assembly Instructions Back of Handi Quilter, Inc. 501 North 400 West North Salt Lake, UT 84054 1-877-697-8458 Front of 2015 Handi Quilter, Inc. www.handiquilter.com Printed in the United

More information

TrendWall Floor-To-Ceiling Panels Installation Instruction

TrendWall Floor-To-Ceiling Panels Installation Instruction TrendWall Floor-To-Ceiling Panels Installation Instruction TrendWall Components Covered by this Instruction: Crown (and accessories) Floor Plate Solid Panel Filler Panel Wall Channel Door Section Pilaster

More information

Topo Freestanding Applications - Private Office

Topo Freestanding Applications - Private Office 4 3 2 Topo Freestanding Applications - Private Office Combo Wrench If you have a problem, question, or request, call your local dealer, or Coalesse at 1.800.627.6770 Or visit our website: www.coalesse.com

More information

STAKS. Crossover Casegoods ASSEMBLY INSTRUCTIONS

STAKS. Crossover Casegoods ASSEMBLY INSTRUCTIONS STAKS Crossover Casegoods ASSEMBLY INSTRUCTIONS Installation Sequence 1. Wall Panels a. Connector Kit Part Identification 3 b. T - 3 Panel Connection Preparation 4 c. X Panel Connection Preparation 5 d.

More information

Castle Frame Assembly Table AT-8. Diagnostics Manual. Castle, Inc. Petaluma, CA

Castle Frame Assembly Table AT-8. Diagnostics Manual. Castle, Inc. Petaluma, CA Castle Frame Assembly Table AT-8 Diagnostics Manual Castle, Inc. Petaluma, CA 800-282-8338 Solutions Index Adjusting the Tabletop.. 8.01 Adjusting the Fence... 8.02 Aligning the Arm... 8.10 Adjusting Bracket..

More information

ACTIV Pro3 height adjustable base Installation Guide

ACTIV Pro3 height adjustable base Installation Guide ACTIV Pro height adjustable base Installation Guide Components ACTIV-Pro Installation Guide Hard ware cable clips x 8mm 5mm 4mm allen keys screw caps x 8 center leg x center leg bracket x end leg x foot

More information

Privacy Wall & Glass Selections Pivot-Hinged Door (For products manufactured after September 14, 2009)

Privacy Wall & Glass Selections Pivot-Hinged Door (For products manufactured after September 14, 2009) Privacy Wall & Glass Selections Pivot-Hinged Door (For products manufactured after September 14, 2009) 3/16" HEX BIT #2 ACR BIT 3/8" HEX SOCKET Full-Height (No Switch) Transom (No Switch) Full-Height (With

More information

IMPULSE G2/PULSE STATIC BRIDGE & RETURN MODULE. Drill. Desk Connecting. Outside by fastening the supplied wood screws from the HK-67 kit through the

IMPULSE G2/PULSE STATIC BRIDGE & RETURN MODULE. Drill. Desk Connecting. Outside by fastening the supplied wood screws from the HK-67 kit through the PART # 1608990 STATIC BRIDGE & RETURN MODULE 1. This sheet covers the steps to install a static bridge or return module with the FX no hinged access panel back option to a height adjustable freestanding

More information

MAG-CONV Basic, 48, 48R & Midline Front Mount

MAG-CONV Basic, 48, 48R & Midline Front Mount Parts Required: Tools Used: Mag Wheels Brakes Brake Rods Mounting Bracket Anti Tippers 7/16" Wrench Screw Driver Rubber Mallet 5/8 Wrench 5mm Allen Wrench Step Execution Figures 1 Remove front 5" total

More information

User Instructions Multiline Otter Scoreboard Caddy Assembly

User Instructions Multiline Otter Scoreboard Caddy Assembly List of parts: User Instructions Multiline Otter Scoreboard Caddy Assembly Single Caddy Double Caddy 1 1 Base assembly with attached wheels 2 4 1 1 2 4 4 8 10 20 12 Uprights (60 or 74 aluminum extrusion)

More information

This instruction manual is an in-depth look and explanation of how to assemble and install the Murphy Bed properly and efficiently.

This instruction manual is an in-depth look and explanation of how to assemble and install the Murphy Bed properly and efficiently. This instruction manual is an in-depth look and explanation of how to assemble and install the Murphy Bed properly and efficiently. Don t be put off by the size of the instruction manual as the large diagrams

More information

INSTALLATION: D1-NOTCH DRYWALL TRIM FLANGE

INSTALLATION: D1-NOTCH DRYWALL TRIM FLANGE T F W 604.549.979 604.549.9555 fluxwerx.com INSTALLATION: D1-NOTCH DRYWALL TRIM FLANGE fixture housing endcap kit optic kit join kit notch 2 cross section notch 4 cross section 4 4" 4-11/2" 4 /8 (111)

More information

Workbench Instructions for Assembly

Workbench Instructions for Assembly Workbench Instructions for Assembly Technical Electronic Workstations and Industrial Workbenches Includes: Cabinets Privacy Panels Stringers Bottom Shelves Table of Contents Tools Required for Assembly...

More information

Series 4 HV Single Monitor Lift Assembly Instructions

Series 4 HV Single Monitor Lift Assembly Instructions 6703 Zinser Street Schofield, WI 54476 6/13/17 Series 4 HV Single Monitor Lift Assembly Instructions Read all the instructions before beginning. Hardware Pack # 53368 Page1 OF 6 Tools Required for Assembly:

More information

Continuum Frame Assembly Instructions

Continuum Frame Assembly Instructions Continuum Frame Assembly Instructions Copyright January 1, 2017 Jim M. Bagley, GraceWood, Inc (Reproduction Prohibited) Version 2.2 Table of Contents Continuum Frame Table of Contents... i Warranty...ii

More information

Video Wall Installation Instructions 2W X 3H, 3W X 3H

Video Wall Installation Instructions 2W X 3H, 3W X 3H Video Wall Installation Instructions 2W X 3H, 3W X 3H www.microndisplaysolutions.com Table of Contents Important Safety Instructions... 3 Configuration... 4 Package Contents, included and optional items...

More information

Angled Side Flush with Panel Face

Angled Side Flush with Panel Face Identify and sort panels by like sizes, fabrics, surface type (tackable vs hard), and NON- POWERED vs POW- ERED. Non-powered panels ship without a powerway. Powered panels include a powerway. See below.

More information

Showpiece Cabinet Integrated Stand For 32" - 52" LCD HDTV

Showpiece Cabinet Integrated Stand For 32 - 52 LCD HDTV Showpiece Cabinet Integrated Stand For 32" - 52" LCD HDTV Installation and Assembly Instructions 2009 Incredible Technologies Inc. Version 0109 Showpiece Cabinet Integrated Stand for 32" - 52" LCD HDTV

More information

Lead Screw Cover Installation

Lead Screw Cover Installation The premier source of tooling, parts, and accessories for bench top machinists. Lead Screw Cover Installation These instructions cover two products: 5201 Telescoping Lead Screw Cover, 7x10, 7x12 5202 Telescoping

More information

Art Rack Assembly Instructions:

Art Rack Assembly Instructions: Art Rack Assembly Instructions: ** PIECES ARE POWDER COATED Do not lay pieces on top of each other or on a hard, rough surface if possible. All bolts will pass from outside towards inside of the cage.

More information

PROFILE Flat Panel Console System Installation Manual

PROFILE Flat Panel Console System Installation Manual PROFILE Flat Panel Console System Installation Manual Table of Contents Page Introduction... 2 Important Safety Information...3, 4 Installation Overview... 4, 5, 6 Single Sided/Single Unit... 7 Double

More information

Mounting Accessories. Installation Guide. VIVOTEK SD83XXE Speed Dome

Mounting Accessories. Installation Guide. VIVOTEK SD83XXE Speed Dome VIVOTEK SD83XXE Speed Dome Mounting Accessories AM-116/117 Pendant Pipe AM-118 Pendant Head AM-221 Gooseneck AM-231 Parapet Mount AM-519 Pendant Adaptor Installation Guide Corresponding part numbers: AM-116:

More information

Pergola Installation Instructions

Pergola Installation Instructions Pergola Installation Instructions TOOLS REQUIRED HAMMER DRILL 1/2 MASONRY BIT PENCIL DRILL 3/16 DRILL BIT LEVEL SQUARE LADDER WRATCHET & SOCKETS RUBBER MALLET 2 TAPE MEASURE Column/Post Placement Table

More information

Glass Front Sauna Room Assembly Manual

Glass Front Sauna Room Assembly Manual Glass Front Sauna Room Assembly Manual Classic Bench Version: 1.3 Note: Above images are for illustrative reference only and may differ from actual item. Parts List Exterior *For room with full glass wall

More information

MM540 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS

MM540 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS MM50 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS Please read this entire manual before you begin. Do not unpack any contents until you verify all requirements on PAGE.

More information

Equilibrium. Conference Table. Installation Instruction. Revision B 11/07/16

Equilibrium. Conference Table. Installation Instruction. Revision B 11/07/16 Equilibrium Conference Table Installation Instruction Revision B 11/07/16 Equilibrium End User Agreement Enwork Equilibrium table bases must be installed directly onto a four inch minimum thickness concrete

More information

FlexFrame - Storage Components and Skins

FlexFrame - Storage Components and Skins FlexFrame - Storage Components and Skins 1/4 Square Drive Ball-Point Hex-Bit Socket 1/8 Short Hex, 1-1/2 Overall Length McMaster Part # 54075A44 Table of Contents Topic Page Storage Components 2 General

More information

Ford Pick Up Rear leaf Spring Kit Installation Instructions

Ford Pick Up Rear leaf Spring Kit Installation Instructions 1948-1956 Ford Pick Up Rear leaf Spring Kit Installation Instructions 1-800-984-6259 www.totalcostinvolved.com Parts 48 inch leaf (2) springs (4) U-bolts 3/8-24 x l 1/4bolts (16) & nuts (2) 1/2-20 x 4

More information

ZAPF PANEL SYSTEM ASSEMBLY INSTRUCTIONS. It is recommended that the components be installed in the sequence of this assembly manual.

ZAPF PANEL SYSTEM ASSEMBLY INSTRUCTIONS. It is recommended that the components be installed in the sequence of this assembly manual. ZAPF PANEL SYSTEM It is recommended that the components be installed in the sequence of this assembly manual. ASSEMBLY INSTRUCTIONS OFFICE FURNITURE FOR THE INFORMATION AGE Table of Contents INSTALLATION

More information

Important Loading Information. Tools Required. Meridian Lateral Files Instructions

Important Loading Information. Tools Required. Meridian Lateral Files Instructions Y Meridian Lateral Files Instructions! WARNING Failure to observe stated capacities below will result in unsafe usage conditions, causing possible product damage or personal injury. Important Loading Information

More information

Revised

Revised Indentify Non-powered panels and separate from Powered panels. Non-powered panel shown at left.. Powered panel shown at left has powerway mounted at factory. Also separate panels by surface type, width

More information

INSIDE PANEL NOT SHOWN TO DETAIL ANCHORING SYSTEM

INSIDE PANEL NOT SHOWN TO DETAIL ANCHORING SYSTEM SIX INCH ALPHA MODULE INSTALLATION KEWAUNEE SCIENTIFIC CORPORATION SIX INCH ALPHA MODULE ANCHORING SYSTEM After Alpha module has been set in desired location. Adjust the four adjustment bolts until the

More information

Parts List. U-DS92ST Ashley Creative Center With Padded Stool Assembly Instructions. [15] - Plastic Thick Washer (2 - pieces) [22] - Wrench (1 piece)

Parts List. U-DS92ST Ashley Creative Center With Padded Stool Assembly Instructions. [15] - Plastic Thick Washer (2 - pieces) [22] - Wrench (1 piece) [1] - 23.5 x 35.5 Top [8] - Drawer Support Rods Parts List [15] - Plastic Thick Washer (2 - pieces) [22] - Wrench [2] - Upper Base left End (1 pieces) [9] - Media Supports (1 pieces) [16] - loor Guides

More information

Boat Lift Canopy Frame Assembly Instructions

Boat Lift Canopy Frame Assembly Instructions Patriot Docks Boat Lift Canopy Frame Assembly Instructions Helpful Tips: Assembling and installing the canopy frame and cover is a two person job. Additional help makes installation easier and is recommended.

More information

EPPA2-KIT DUAL MONITOR ARM CONVERSION

EPPA2-KIT DUAL MONITOR ARM CONVERSION EPPA2-KIT DUAL MONITOR ARM CONVERSION EPPA2-KIT Rev A 10/17 Model EPPA2-KIT-XXX ASSEMBLY AND ADJUSTMENT EPPA2-KIT PARTS AND TOOLS PLEASE REVIEW these instructions before beginning the assembly and adjustment

More information

Deck Mount Installation with Bench

Deck Mount Installation with Bench Deck Mount Installation with Bench 1. Mark track with square. 2. Cut tracks with saw. 3. Drill ¼ hole (if needed.) 4. Countersink track. 5. Countersink all track 6. File all track ends. ends. 7. Lay out

More information

Setup. The Faraday Cage is available in two types of configurations. Cage for mounting to a full perimeter enclosure on series tables.

Setup. The Faraday Cage is available in two types of configurations. Cage for mounting to a full perimeter enclosure on series tables. Faraday CageSetup, 2017 Setup The Faraday Cage is available in two types of configurations. Cage for mounting to a full perimeter enclosure on 63-500 series tables. Cage with a base plate for use on a

More information

DeckRail A Product of DeckRite LLC 3912 East Progress North Little Rock, AR Phone: (501) Fax: (501)

DeckRail A Product of DeckRite LLC 3912 East Progress North Little Rock, AR Phone: (501) Fax: (501) Disclaimer: Deck Rail Glass Railing Installation Guide This guide is not intended to replace a trained professional installer. The drawings and instructions contained within are for demonstration purposes

More information

Commercial Wine & Liquor Display. Double Displays

Commercial Wine & Liquor Display. Double Displays Commercial Wine & Liquor Display Double Displays Congratulations! You have purchased a superior commercial wine rack kit. These commercial kits have been specifically designed to properly store and display

More information

Assembly Instructions

Assembly Instructions Seminar Tables May 2014 Seminar Tables - Floor Anchor Specifications Floor Anchor Specifications 3 3/ 4 5 / 16 (4)½ diameter holes 3 1 / 4 2 4 8 #12.7503.KIT4 1 5 / 4 Hilti KH-EZ x 2 / 8 Max. Torque: 18

More information

Note: This assembly instruction will cover all configurations of Alloy adjustable height double bases.

Note: This assembly instruction will cover all configurations of Alloy adjustable height double bases. Note: This assembly instruction will cover all configurations of adjustable height double bases. 1 Screw in the provided adjustable glides into each leg as shown in Figure A. Two glides per leg. Figure

More information

TIP FOR GETTING STARTED

TIP FOR GETTING STARTED Tip for getting started TIP FOR GETTING STARTED Be careful not to drill into any electrical wires, ductwork, plumbing or other damagable components. If you have any questions on the locations of these

More information

LEGENDS RETRACTABLE DOOR SCREENS

LEGENDS RETRACTABLE DOOR SCREENS I N S T A L L A T I O N I N S T R U C T I O N S 1 MOUNTING OPTIONS Recess : Mount the Screen Cassette using Recess Mounting Clips Recess within the door jamb area. Recess installations are the most typically

More information

The Phoenix. Professional Quilting Frame. Copyright January 1, 2016 Jim M. Bagley, GraceWood, Inc (Reproduction Prohibited) Version 2.

The Phoenix. Professional Quilting Frame. Copyright January 1, 2016 Jim M. Bagley, GraceWood, Inc (Reproduction Prohibited) Version 2. The Phoenix Professional Quilting Frame Copyright January 1, 2016 Jim M. Bagley, GraceWood, Inc (Reproduction Prohibited) Version 2.1 1 The Phoenix Professional Quilting Frame Parts List Box 1...3 Box

More information

Shetland Stalls Installation Instructions

Shetland Stalls Installation Instructions Shetland Stalls Installation Instructions RAMM Horse Fencing and Stalls 13150 Airport Hwy. Swanton, OH 43558-9615 1-800-434-8456 Rev. 1/9/18 Before you start Kit can accommodate up to 12 wide stall front

More information

Height Adjustable Benching End Panel and Utility Pole

Height Adjustable Benching End Panel and Utility Pole Height Adjustable Benching End Panel and Utility Pole Tools required: END PANEL Jig Saw Power Drill END PANEL WITH UTILITY POLE Bit Holder Long #2 Square Drive Bit 5mm Hex Drive Bit UTILITY POLE Level

More information

HQ Studio Frame Two-Foot Section Assembly Instructions From Twelve-Foot to Ten-Foot

HQ Studio Frame Two-Foot Section Assembly Instructions From Twelve-Foot to Ten-Foot HQ Studio Frame Two-Foot Section Assembly Instructions From Twelve-Foot to Ten-Foot HQ Studio Frame Two-Foot Includes: Includes one (1) two-foot table frame with plastic top, two (2) two-foot track supports,

More information

CABINETRY Assembly Instructions

CABINETRY  Assembly Instructions www.hdicabinetry.com Assembly Instructions TABLE OF CONTENTS Category Page(s) Section 1: Framed Series Base Cabinet Instructions Wall Cabinet Instructions Easy Reach Cabinet Instructions 1.01-1.04 1.05-1.06

More information

LEGENDS RETRACTABLE DOOR SCREENS

LEGENDS RETRACTABLE DOOR SCREENS LEGENDS RETRACTABLE DOOR SCREENS MAGNETIC LATCHING DESIGN SYSTEM 42 I N S T A L L A T I O N I N S T R U C T I O N S 1 MOUNTING OPTIONS Recess : Mount the Screen Cassette using Recess Mounting Clips Recess

More information

RBP-1215B-RX DODGE RAM QUAD CAB RX3

RBP-1215B-RX DODGE RAM QUAD CAB RX3 RBP-1215B-RX3 2002-2017 DODGE RAM 15-3500 QUAD CAB RX3 Passenger side RX-3 Side Step Drill Template Passenger side rear Modular Bracket (6) L Support Brackets Driver side rear Modular Bracket Driver side

More information

Qwik-Fence Installation Instructions

Qwik-Fence Installation Instructions Qwik-Fence Installation Instructions 1 Tools Required The following installation instructions should be used as a guide for installing Folding Guard Qwik-Fence Partitions. Good common sense and appropriate

More information

Replacing the Reciprocator on an SWF Multi-head.

Replacing the Reciprocator on an SWF Multi-head. Replacing the Reciprocator on an SWF Multi-head. Follow the instructions below to replace the reciprocator in the SWF multi-head machines. The tools required are found in the tool kit that came with the

More information

INSTALLATION INSTRUCTIONS FOR HAND OPERATED MODELS: 170, 171-R, 171-N, 172, 260

INSTALLATION INSTRUCTIONS FOR HAND OPERATED MODELS: 170, 171-R, 171-N, 172, 260 INSTALLATION INSTRUCTIONS FOR HAND OPERATED MODELS: 170, 171-R, 171-N, 172, 260 I. SUSPENDED INSTALLATIONS NOTE: MODEL 260 FENSTEEL TRACK IS ASSEMBLED IN THE SAME MANNER AS DESCRIBED BELOW WITH THE EXCEPTION

More information

Assembly Instructions

Assembly Instructions Unite Panel System Hinge Door July 2016 #12 x / slotted hex washer head bolt Figure 1 threshold bracket frame Detail F threshold bracket threshold bracket (installed) #12 x / slotted hex washer head bolt

More information

Hollywood Swing Away 2 and 4 Bike Racks Assembly and Installation Guide

Hollywood Swing Away 2 and 4 Bike Racks Assembly and Installation Guide Hollywood Swing Away 2 and 4 Bike Racks Assembly and Installation Guide Tools Required: two adjustable wrenches, pliers, ¾ socket wrench recommended Note: please do assembly near your vehicle as you Can

More information

The Festival Assembly Instructions

The Festival Assembly Instructions The Festival Assembly Instructions Toll Free: 866.768.8465 Hours: 9-5 Monday-Friday EST www.homeplacestructures.com Package ships as shown CONTACT INFORMATION: HomePlace Structures 301 Commerce Drive New

More information

Replacing the Reciprocator on the SWF Compact Series Machine (601C and 1201C)

Replacing the Reciprocator on the SWF Compact Series Machine (601C and 1201C) Follow the instructions below to replace the reciprocator in the SWF Compact series machines. The tools required can be found in the tool kit that came with the machine. Preparation 1. First, place the

More information

ESA-200 Fixed Sidelite

ESA-200 Fixed Sidelite Exterior View Installation Instructions For use with ESA II Controller 1 Tools Required: Suggested Fasteners Required - (Not supplied) Screwdrivers Small Straight (FlatBlade) - for Terminal Block wiring

More information

Series Adjustable Height Tables

Series Adjustable Height Tables Series 7.2 - Adjustable Height Tables Tools required: Power Drill #2 SQUARE DRIVE BIT If you have a problem, question, or request, call your local dealer, or Steelcase Line 1 at 888.STEELCASE (888.783.3522)

More information

CONTENTS TOOL LIST U P S I D E I N N O V A T I O N S, L L C RAMP AND STEP SYSTEM ASSEMBLY INSTRUCTIONS. Revised: June 2013

CONTENTS TOOL LIST U P S I D E I N N O V A T I O N S, L L C RAMP AND STEP SYSTEM ASSEMBLY INSTRUCTIONS. Revised: June 2013 U P S I D E I N N O V A T I O N S, L L C RAMP AND STEP SYSTEM ASSEMBLY INSTRUCTIONS TOOL LIST Required Tools: - Reciprocating Saw with Metal Cutting Blade - Drill - 7/16 Drill Bit for Metal Drilling -

More information

Spring Loaded All Season Roll-Up Doors

Spring Loaded All Season Roll-Up Doors Spring Loaded All Season Roll-Up Doors STAND-OFF MOUNTING METHOD INSTALLATION INSTRUCTIONS READ THIS FIRST Carefully examine the crate(s) for damage before opening. If the carton is damaged, immediately

More information

Multiples EM_ 1.4. Install 1X1/1X2/1X3/1X4 Housings. Installation Instructions for. This product is suitable for indoor locations.

Multiples EM_ 1.4. Install 1X1/1X2/1X3/1X4 Housings. Installation Instructions for. This product is suitable for indoor locations. Installation Instructions for 90EMULTI Multiples EM_. GENERAL PRODUCT I NFORMATION: This product is suitable for indoor locations. This product can be dimmed with a standard electronic dimmer or a 0-0V

More information

LIGHT FIXTURES MUST BE COMPLETELY INSTALLED PRIOR TO CEILING CONSTRUCTION

LIGHT FIXTURES MUST BE COMPLETELY INSTALLED PRIOR TO CEILING CONSTRUCTION CAUTION: BEFORE BEGINNING INSTALLATION REVIEW LAYOUT DRAWINGS, AND SHIPMENT. MAKE SURE ALL LIGHT S AND MATERIALS ARE ON SITE AND READILY ACCESSIBLE. IF ANY ICON MATERIALS ARE MISSING, CONTACT ICON INTERNATIONAL

More information

Installing the Profile Privacy Panel. Assemble top mounting bracket. Prerequisites. Tools

Installing the Profile Privacy Panel. Assemble top mounting bracket. Prerequisites. Tools Installing the Profile Privacy Panel Complete these instructions to install the Profile Privacy Panel. Privacy panels are available in various heights to match tiers and include mounting hardware for slat

More information

HQ Pole Upgrade Kit for HQ Adjustable Table and HQ QuilTable Assembly Instructions 1

HQ Pole Upgrade Kit for HQ Adjustable Table and HQ QuilTable Assembly Instructions 1 HQ Pole Upgrade Kit for HQ Adjustable Table and HQ QuilTable Assembly Instructions QF09775 The pole upgrade kit can be used with or without the QF09700 HQ Precison-Glide track upgrade kit. What s Included

More information

GroundControl. Follow instructions contained in this manual. Incorrect installation could result in serious injury or damage to property.

GroundControl. Follow instructions contained in this manual. Incorrect installation could result in serious injury or damage to property. GroundControl TM use supplied hardware Use only hardware supplied in your GroundControl kit or supplied by an authorized YAKIMA dealer. Use of unauthorized parts in the GroundControl system could result

More information

Heavy Duty Ceiling Tilt Mount Installation Manual

Heavy Duty Ceiling Tilt Mount Installation Manual HD-CTM-5580 Heavy Duty Ceiling Tilt Mount Installation Manual *This Installation requires a minimum of two people. For your safety: Read the complete instruction manual before starting an installation

More information

#916 CLASSIC 16 GUN CABINET ASSEMBLY INSTRUCTIONS

#916 CLASSIC 16 GUN CABINET ASSEMBLY INSTRUCTIONS Thank you for purchasing this quality product. A list of PARTS and INSTRUCTIONS is included to assist you. Unpack and identify all parts included on the Parts List and Hardware List. If parts are missing,

More information

Linear Hook- on Worksurfaces

Linear Hook- on Worksurfaces Linear Hook- on Worksurfaces Linear Hook-On Worksurfaces come in three depths and seven lengths. Different worksurfaces have different reqirements for installation that are outlined below. 27 inch deep

More information

SawStop. T-GlideTM. Fence System- Professional Series II OWNER S MANUAL

SawStop. T-GlideTM. Fence System- Professional Series II OWNER S MANUAL SawStop T-GlideTM Fence System- Professional Series II OWNER S MANUAL Warranty SawStop warrants to the original retail purchaser of a new T-Glide Fence System - Professional Series II from an authorized

More information

END FEED INSTALLATION

END FEED INSTALLATION STARLINE PLUG-IN RACEWAY END FEED INSTALLATION The Universal End Feed (product numbers beginning with URPF, URDF, or MRPF, MRDF) provides the installer a provision to connect supply power to the Plug-In

More information

INSTALLATION INSTRUCTIONS FOR HAND OPERATED SILENT STEEL ADC HEAVY DUTY CURTAIN TRACK MODELS: 280, 281, 282, 280-A, 283-N, 283-R

INSTALLATION INSTRUCTIONS FOR HAND OPERATED SILENT STEEL ADC HEAVY DUTY CURTAIN TRACK MODELS: 280, 281, 282, 280-A, 283-N, 283-R INSTALLATION INSTRUCTIONS FOR HAND OPERATED SILENT STEEL ADC HEAVY DUTY CURTAIN TRACK MODELS: 280, 281, 282, 280-A, 283-N, 283-R I. SUSPENDED INSTALLATIONS 1. Lay the two track halves on the floor with

More information

model tsa-sa48 Sliding Crosscut Table installation guide

model tsa-sa48 Sliding Crosscut Table installation guide model tsa-sa48 Sliding Crosscut Table installation guide A Note About Color Variations Among Anodized Aluminum Components Congratulations on the purchase of this SawStop Sliding Crosscut Table. We at SawStop

More information

Answer Power Beam and Boundary Screen

Answer Power Beam and Boundary Screen Answer Power Beam and Boundary Screen 5/16 MAGNETIC 3/8 If you have a problem, question, or request, call your local dealer, or Steelcase Line 1 at 888.STEELCASE (888.783.3522) for immediate action by

More information