Tour Worksurfaces and Supports
|
|
- Anne Newman
- 5 years ago
- Views:
Transcription
1 R Tour Worksurfaces and Supports Table of Contents Topic Page COLUMN SUPPT SUPPT FRAME TIE BRACKET TO COUNTER Worksurface to Shelf Attachment 2 Worksurface to Counter Attachment Bracket 3 Worksurface Tied to End of Counter 4 Floating Worksurface Z Bracket Attachment Myfile Attachment to Worksurface 5 6 TO SHELF BRACKET NOTE: Use all the fasteners supplied with the supports. All floor supports have pilot holes for alignment. POST LEG LAMINATE PANEL SUPPT END OF COUNTER TO BRACKET T-27 TX POST LEG TAPERED LEG (SHOWN) POST LEG (SHOWN) TAPERED LEG TAPERED LEG MYFILE PEDESTAL FLOATING Z BRACKET COLUMN SUPPT 2008 Steelcase Inc. Grand Rapids, MI 4950 U.S.A. Printed in U.S.A. Page of 6
2 Worksurface to Shelf Attachment. Position two (2) worksurface to shelf brackets to be approximately from edge of worksurface being mounted (a). Attach worksurface to shelf bracket(s) to shelf using three (3) screws each (b). Top View a b 2. Position worksurface onto worksurface to shelf brackets (2a) and attach each bracket to worksurface using three (3) screws each (2b). TO SHELF BRACKET 2b SHELF 2-/4" NOTE: Position brackets from the edge of the worksurface. Distance between the two brackets will vary depending on the worksurface width. 2a A single worksurface can also be mounted to two (2) counters. b 2a NOTE: Use three (3) brackets for full length. Page 2 of 6
3 Worksurface to Counter Attachment Bracket. Position brackets to be approximately from the edge of worksurface being mounted (a). If possible, use supplied holes underneath counter for mounting the brackets and place brackets over holes and attach each bracket using two (2) /4-20 nuts and two (2) /4-20 screws (b). /4-20 NUT TIE BRACKET TO COUNTER b a Top View 2. Place worksurface onto brackets (2a) and attach each bracket to the worksurface using two (2) screws each (2b). COUNTER -5/6" 2b NOTE: Use three (3) brackets for full length. 2a /4-20 NUT A single worksurface can also be mounted to two (2) counters. TIE BRACKET TO COUNTER Page 3 of 6
4 Worksurface Tied to End of Counter. Remove each frame corner trim as shown. 2. Break each piece of trim in half along die cut. 3. Reposition both partial pieces of trim back on frame as shown. /2 FRAME CNER TRIM 4 FLAT HEAD TX DRIVE END OF COUNTER TO BRACKET 4. Position end of counter to worksurface bracket to end of counter and attach using two (2) screws. 3 FRAME CNER TRIM NOTE: Worksurface needs to be fully supported. This tie bracket is to be used as a tie to the counter, not a support. 5. Set worksurface onto end of counter to worksurface bracket and attach using two (2) screws. 2 DISCARD THIS PIECE 5 SAVE THIS PIECE Page 4 of 6
5 Floating Worksurface Z Bracket Attachment. The host table and the round worksurface must be supported by one () column base or two (2) post or tapered legs per the application guidelines. 2. The floating worksurface Z bracket is to be centered on the round worksurface and 8" maximum from the host table. POST TAPERED LEGS POST TAPERED LEGS POST TAPERED LEGS 36" ROUND MAX. POST TAPERED LEGS C L C L 36" ROUND MAX. Z BRACKET Z BRACKET Z BRACKET 8" MAX. 8" MAX. 8" MAX Page 5 of 6
6 Myfile Attachment to Worksurface. Fully extend drawer and push in on the side tabs on the suspension, as shown, to remove the drawer. 2. Place worksurface over the pedestal. Locate the worksurface flush to the side of the pedestal and flush to the rear of the pedestal as shown. Secure the worksurface to the pedestal with two (2) screws supplied. NOTE: Drilling /8" pilot holes will ease the attachment of the screws. 3. Reinstall drawer and level worksurface with glides provided on the bottom of the pedestal. 3 S 2 FLUSH FLUSH Page 6 of 6
Opus Standard Corner Trim Unit
Opus Standard Corner Trim Unit If you have a problem, question, or request, call your local dealer, or Steelcase Line 1 at 888.STEELCASE (888.783.3522) for immediate action by people who want to help you.
More informationJenny Legs Assembly Instructions
Jenny Legs Assembly Instructions R EXTENDED PHILLIPS BIT MM ALLEN WRENCH 6MM HEX DRIVE /" 007 Steelcase Inc. Grand Rapids, MI 90 U.S.A. Printed in U.S.A. Page of 6 88000 Rev F Jenny Club Instructions:
More informationTopo Freestanding Applications - Private Office
4 3 2 Topo Freestanding Applications - Private Office Combo Wrench If you have a problem, question, or request, call your local dealer, or Coalesse at 1.800.627.6770 Or visit our website: www.coalesse.com
More informationUniversal Storage 1-Hi and 1.5-Hi Lateral File Counterweight Package
Universal Storage 1-Hi and 1.5-Hi Lateral File Counterweight Package 1-Hi 18" & 24 Deep Cabinets (pages 2-4) 1.5-Hi 18" & 24 Deep Cabinets Drawer/Drawer or Open/Drawer (pages 5-7) CAUTION Please refer
More informationAssembly Instructions Above Worksurface Riser Shelf Systems and Back / End Stops
Assembly Instructions Above Riser Shelf Systems and Back / End Stops Back Stops and End Stops Adjustable Riser Shelves Instrument Riser Shelves Stationary Riser Shelves IMPORTANT PLEASE READ THESE INSTRUCTIONS
More informationGroupwork Tables. Table of Contents. Page Topic. Page 1 of Rev G
Table of Contents Page Topic 2-13 T-Legs & s Installation 14 Typical Table Configurations 15 Wire Manager Installation Groupwork Tables To ensure stability and prevent possible injury, standing height
More informationWorkbench Instructions for Assembly
Workbench Instructions for Assembly Technical Electronic Workstations and Industrial Workbenches Includes: Cabinets Privacy Panels Stringers Bottom Shelves Table of Contents Tools Required for Assembly...
More informationFitWork Walkstation Series 7 AdjusTables
FitWork Walkstation Tools Required: #2 Phillips Bit with Extension Page 1 of 20 A7TG660606H A7TR663232H FitWork Walkstation 4mm Hex Head Bit A7TG660632H A7TR383030H www.details-worktools.com A7TG663206H
More informationIMPULSE G2/PULSE STATIC BRIDGE & RETURN MODULE. Drill. Desk Connecting. Outside by fastening the supplied wood screws from the HK-67 kit through the
PART # 1608990 STATIC BRIDGE & RETURN MODULE 1. This sheet covers the steps to install a static bridge or return module with the FX no hinged access panel back option to a height adjustable freestanding
More informationLF Series Assembly Instructions
LF Series Assembly Instructions 1998760 Revision A-10 Complete Series Master Packet 2010 Kimball International, Inc. T 800.482.1818 F 812.482.8300 Footprint Storage and Metal Filing Systems Assembly Instructions
More informationArlink 7000 Workstation
Arlink 7000 Workstation Instructions for Assembly Basic Bench Assembly Undersurface Accessories Above Surface Accessories VSI Mounting Instructions Making Workspace Work is a trademark of Lista International
More information487 Cachet Swivel - Base Chair Replace Front Seat Support or Seat
487 Cachet Swivel - Base Chair Replace Front Seat Support or Seat SPECIAL ALLEN WRENCH PROVIDED If you have a problem, question, or request, call your local dealer, or Steelcase Line 1 at 888.STEELCASE
More informationWorkbench Instructions for Assembly
Workbench Instructions for Assembly FlexWorks is a trademark of Lista International Corporation. Making Workspace Work is a trademark of Lista International Corporation. Document Number: MD002A3 Print
More informationcompile system INSTALLATION GUIDE Updated January 2019
INSTALLATION GUIDE Updated January 09 compile system Table of Contents Panels 0 Quick Connect Clips 0 Lock Clips 0 Panel Trims 0 Privacy Glass 0 Post Base Covers 04 Electrical 04 Power Distribution Harness
More informationExtra Wide Designer Lockers Series Installation Instructions
Extra Wide Designer Lockers 20000 Series Thank you for selecting the 20000 Series Extra Wide Designer Lockers. We are confident that the quality and construction of the lockers will prove to be a good
More informationASSEMBLY INSTRUCTIONS FOR DESK & CREDENZA PRODUCTS
ASSEMBLY INSTRUCTIONS FOR DESK & CREDENZA PRODUCTS (1) COMPONENT LIST FOR DESK & CREDENZA PRODUCTS NOTE: Please count and inspect all pieces before disposing of any carton or packing materials. 24" x 72"
More informationLarge Case Storage - Counterweights
Large Case Storage - Counterweights Lateral File/Combo Cabinet CAUTION Please refer to the Steelcase Specification Guide for Storage for additional guidance on determining the correct counterweight package.
More informationSeries 7 AdjusTable Height Tables
Series 7 AdjusTable Height Tables Tools required: #2 Phillips Bit with Extension #2 Square Drive Bit 4mm Hex Drive Bit #3 Phillips Bit If you have a problem, question, or request, call your local dealer,
More informationSeries 7 - Adjustable Height Tables
Page 1 of 22 Series 7 - Adjustable Height Tables Installation Instructions Tools required: #2 Phillips Bit with Extension #2 Square Drive Bit 4mm Hex Drive Bit Series 7 - Adjustable Height Tables Installation
More informationASSEMBLY INSTRUCTIONS RIGHT & LEFT HAND "J" TABLE
ASSEMBLY INSTRUCTIONS RIGHT & LEFT HAND "J" TABLE (1) COMPONENT LIST FOR RIGHT & LEFT HAND "J" TABLE NOTE: Please count and inspect all pieces before disposing of any carton or packing materials. 24" x
More informationCOACT MEDIA UNIT ASSEMBLY WITH X9 OPEN SHELF STORAGE OPTION PART # INSTALLATION INSTRUCTIONS
PART # 1609103 MEDIA UNIT ASSEMBLY WITH X9 OPEN SHELF STORAGE OPTION 1. Begin by placing the back panel on a flat non-marring surface, making sure the pre-drilled holes are facing up. Next, position the
More informationFlexFrame - Storage Components and Skins
FlexFrame - Storage Components and Skins 1/4 Square Drive Ball-Point Hex-Bit Socket 1/8 Short Hex, 1-1/2 Overall Length McMaster Part # 54075A44 Table of Contents Topic Page Storage Components 2 General
More informationKai Installation Instructions
Kai Installation Instructions Before Beginning Installation Read through the entire instruction thoroughly A minimum of 2 people are required for this assembly These instructions reflect typical assemblies;
More informationSeries 9000 Panel Door; In-Line, Corner and Permanent Wall Application
Series 9000 Panel Door; In-Line, Corner and Permanent Wall Application 5/32" Drill Bit In-Line Corner Permanent Wall 3/16" Allen Wrench If you have a problem, question, or request, call your local dealer,
More informationArlink 7000 Workstation
Arlink 7000 Workstation Instructions for Assembly Basic Bench Assembly Undersurface Accessories Above Surface Accessories Making Workspace Work is a trademark of Lista International Corporation. Creation
More informationArlink 8000 Workstation
Arlink 8000 Workstation Instructions for Assembly Introduction Basic Frame Assembly Worksurface Assembly Drawer and Power Beam Assembly Light Fixture and Shelves Worksurface Grounding Instructions Wrist
More informationTechBench Installation Manual
Manual Table of Contents TechBench Overview....2 Bench Assembly Linear,36 (914,4mm) Wide 96 (2438,4mm) Wide 3,4,5,6,7 Bench Assembly Linear,24 (609,6mm) Wide 30 (762mm) Wide..8,9 Bench Assembly Corner
More information434 Cobi Chair - Seat Shell Replacement
434 Cobi Chair - Seat Shell Replacement PROFILE OF HARDWARE FOR CLARITY #8-18 x 1/2" Pan Head Tapping Screw Magnetic Bit Holder M6 x 45mm Wafer Head Screw T-30 Large flat-bladed screwdriver If you have
More informationAssembly Instructions & General Overview
Assembly Instructions & General Overview 1. General Overview & Assembly Order...Page 3 2. Assembling the Structural Components Page 4-11 3. Power, Data, Power Poles and Cable Floor Boxes.Page 12-17 4.
More informationFootprint Mobile Assembly Instructions
Footprint Mobile Assembly Instructions 1998754 Revision -1 Complete Series Master Packet If you have any questions concerning these instructions, please call Kimball Office Customer Service. 20 Kimball
More informationIMPULSE G2/PULSE STATIC BRIDGE & RETURN MODULE. Drill. Desk Connecting. Outside by fastening the supplied wood screws from the HK-67 kit through the
PART # 1608990 STATIC BRIDGE & RETURN MODULE 1. This sheet covers the steps to install a static bridge or return module with the FX no hinged access panel back option to a height adjustable freestanding
More informationBSM, GSM & GSS. Joint Kit Instruction. (Modified for IMPACT) (NSF Certified) Curved Glass Fresh Meat Delicatessen and Seafood Merchandisers
BSM, GSM & GSS Joint Kit Instruction (Modified for IMPACT) (NSF Certified) Curved Glass Fresh Meat Delicatessen and Seafood Merchandisers February, 1999 JOINT ASSEMBLY PARTS LIST Item Quantity Description
More informationTechnical Environment Systems INSTALLATION MANUAL
Technical Environment Systems INSTALLATION MANUAL Technical Environment Systems INSTALLATION MANUAL Table of Contents INTRODUCTION Full Frame, Open Frame & Upright Assembly...A Foundations...B Mobile &
More informationCABINETRY Assembly Instructions
www.hdicabinetry.com Assembly Instructions TABLE OF CONTENTS Category Page(s) Section 1: Framed Series Base Cabinet Instructions Wall Cabinet Instructions Easy Reach Cabinet Instructions 1.01-1.04 1.05-1.06
More informationAssembly Instructions
Laminate/Phenolic & 1 Pc Butcherblock Tops Before you begin, please make sure all parts and proper quantities are included. (See on next page) Any parts damaged during shipment must be reported within
More informationSeries Adjustable Height Tables
Series 7.2 - Adjustable Height Tables Tools required: Power Drill #2 SQUARE DRIVE BIT If you have a problem, question, or request, call your local dealer, or Steelcase Line 1 at 888.STEELCASE (888.783.3522)
More informationAssembly Instructions
Selling Station Assembly Instructions View from above without top A B C D Rounded finished corners on A & D Square unfinished 3-sides on B & C Selling Station Components (2) 2' x 6' Side s Have a channel
More informationLCD LIFT Flat Panel Display System Installation Manual. Table of Contents
LCD LIFT Flat Panel Display System Installation Manual Table of Contents Page Installation Overview... 2 Trim Ring Installation... 3 LCD Lift Installation....4 Actuator Switch Installation.5 Top Plate
More informationTIP FOR GETTING STARTED
Tip for getting started TIP FOR GETTING STARTED Be careful not to drill into any electrical wires, ductwork, plumbing or other damagable components. If you have any questions on the locations of these
More informationPreference Collection and Treatment Console INSTALLATION GUIDE
Preference Collection 5580.69 and 5580.96 Treatment Console INSTALLATION GUIDE WARNING Failure to install the 5580 as described in this installation guide may cause the unit to collapse, resulting in serious
More informationFootprint Worksurface Assembly Instructions
Footprint Worksurface Assembly Instructions 1998756 Revision E-13 Complete Series Master Packet If you have any questions concerning these instructions, please call Kimball Office Customer Service. 2013
More informationTop Closure Kit Accessory for Music Library System
Assembly Instructions Top Closure Kit Accessory for Music Library System Contents Required Tools.....................................2 Installation Requirements............................2 Fasteners -
More informationHover. Installation Instructions. Raised Panel. Version
Installation Instructions Version 8-2-17 Raised Panel Table of Contents Page Raised Panel Trough 3-13 Platform Trough 14-20 Platform 120 Degree Trough 21-24 Electrical 25-28 Type A Electric Bases 29-31
More informationInstalling Electronic Media Storage Components into Lateral File Cabinets
Steelcase, Inc. Grand Rapids, MI 49501 U.S.A. 1-888-783-3522 Installing Electronic Media Storage Components into Lateral File Cabinets 830-CH-9 830-CH-12 830-CH15 836-CH-9 836-CH-12 836-CH-15 842-CH-9
More informationINSTRUCTION SHEET U19
U19 All Refrigerator and All Freezer Trim Kit Installation Product Line: U19 All Refrigerator and All Freezer Models Parts Included in Kit TRIMKITEZ1 (Part# 297333500): Single Trim Kit Components Single
More informationInstallation Instructions Evolve Cabinets
Installation Instructions Evolve Cabinets Follow these installation instructions for Evolve upper, base, tall, and scope cabinets with AireCore or wood composite construction. Tools needed: Flat head screwdriver
More informationSingle Sided Height Adjustable Benching
Single Sided Height Adjustable Benching Bit Holder Power Drill Long # Square Drive Bit 5mm Hex Drive Bit T-30 Torx Drive Bit Hex Key -.5mm (Provided) SERIES 5 Hex Key - 3mm Socket Adaptor (or) If you have
More informationPremium Whiteboard and Tackboard Mounting
Premium Whiteboard and Tackboard Mounting #2 BIT If you have a problem, question, or request, call your local dealer, or Steelcase Line 1 at 888.STEELCASE (888.783.3522) for immediate action by people
More informationWalk-in Configurations
Walk-in Configurations Includes Wall-to-Open, Corners, and Corner Rounder Bars INSTALLATION INSTRUCTIONS Tools needed: Tape measure, level, pencil, #2 Phillips head screw driver or power drill with a 6"
More informationOXYGEN INSTALLATION. Revision date
12345 1 Hardware List 12345 Flat head wood screw #9 x 7/8 long with #2 Phillips drive, silver Used to attach surfaces and end panels Hex set screw ½-13 x 2 long with 1/4 hex drive, black Used on Legs Hex
More informationc:scape Shared Tables - Freestanding and Tethered
c:scape Shared Tables - Freestanding and Tethered Furniture should be installed in sequence shown below. 1 2 3 4 5 6 BEAM MID STORAGE DESKING POWER LOW STORAGE PRIVACY THIS INSTALLATION SEQUENCE IS HERE.
More informationHeight Adjustable Benching End Panel and Utility Pole
Height Adjustable Benching End Panel and Utility Pole Tools required: END PANEL Jig Saw Power Drill END PANEL WITH UTILITY POLE Bit Holder Long #2 Square Drive Bit 5mm Hex Drive Bit UTILITY POLE Level
More informationSelect Lab Adjustable Height Workstation
Assembly Instructions Select Lab Adjustable Height Workstation Mobile version is shown. Also available without casters. Contents Important User Information.............................. 2 Safety Precautions....................................
More informationOpus Base Unit Assembly
Opus Base Unit Assembly 5/16" NOTE: All cam locks need to be rechecked to confirm they are tight before installation. Gaps could result if not completely tightened and effect assembly. 2 Foot Scrap Board
More informationStance 6085 Treatment Tables Assembly Instructions
Stance 6085 Treatment Tables Assembly Instructions Model #ST6085 Treatment Table only Model #ST6085-SH Treatment Table with Shelf Model #ST6085-DW Treatment Table with Shelf and Two Drawer Cabinet Your
More informationINSTRUCTIONS FOR ASSEMBLY 2355mm x 3125mm Workshop
Manufacturer of Christie Glasshouses and Sheds INSTRUCTIONS FOR ASSEMBLY 2355mm x 3125mm Workshop 1 Thomas Burns Street, Dunedin Phone (03) 477 7909 www.allans.co.nz Congratulations on your purchase of
More information110 and 555 Markerboard, Chalkboard and Tackboard Mounting
0 and 555, Chalkboard and Tackboard Mounting 0 # BIT 0 Splined 0 and 555 Tackboard POWER GRIPS 555 If you have a problem, question, or request, call your local dealer, or Steelcase Line at 888.STEELCASE
More informationAngled Side Flush with Panel Face
Identify and sort panels by like sizes, fabrics, surface type (tackable vs hard), and NON- POWERED vs POW- ERED. Non-powered panels ship without a powerway. Powered panels include a powerway. See below.
More informationInstallation Manual for Metal Emperor Lockers
P a g e 1 Table of Contents Page General Notes and Tools Required 2-3 Assemble Shelves with Coat Hooks/Coat Rods 4 Fastening Chart 5 Knock Down Locker Assembly (Banks of Three) 6-12 Appendix A: Dress End
More informationY1160A EIA Rack Sliding Shelf Installation Note
Y1160A EIA Rack Sliding Shelf Installation Note This installation note contains procedures for mounting L4400 Series LXI instruments in EIA rack cabinets using the Y1160A sliding shelf rack mount kit.
More informationDuraRac Shelving System
GM Full Size Van Assembly Installation Instructions Sheet 1 of 13 BEFORE YOU START! IMPORTANT INSTALLATION STEPS ARE DENOTED USING A STOP SIGN. THESE STEPS MUST BE PERFORMED IN THE SPECIFIED ORDER TO ENSURE
More informationRiverside. Oakmont Queen Storage Bed Assembly Instructions
Queen Storage Bed Page 1 of 7 8 pcs. 8 pcs. 1 pc. 1 pc. 8 pcs. 8 pcs. 8 pcs. 8 pcs. 1 pc. 1 pc. 20270 --5/0 Sleigh Headboard 20274 --5/0-6/6 Bed Rails 20273 -- 5/0 Storage Footboard, Panels, Slats Queen
More informationBUTCHER BLOCK MICROWAVE OVEN STAND
BUTCHER BLOCK MICROWAVE OVEN STAND 828 The butcher block has fallen out of favor in recent years, replaced by the countertop cutting board in an attempt to save space. This design, however, makes the butcher
More informationINSTRUCTIONS FOR ASSEMBLY 2355mm x 4665mm Workshop
Manufacturer of Christie Glasshouses and Sheds INSTRUCTIONS FOR ASSEMBLY 2355mm x 4665mm Workshop 1 Thomas Burns Street, Dunedin Phone (03) 477 7909 www.allans.co.nz Congratulations on your purchase of
More informationSetup. The Faraday Cage is available in two types of configurations. Cage for mounting to a full perimeter enclosure on series tables.
Faraday CageSetup, 2017 Setup The Faraday Cage is available in two types of configurations. Cage for mounting to a full perimeter enclosure on 63-500 series tables. Cage with a base plate for use on a
More informationFORD INTERCEPTOR SEDAN READY BUCKLE
INSTALLATION MANUAL FORD INTERCEPTOR SEDAN READY BUCKLE PART# FT3501RB We recommend you read through the installation guide prior to installation, if you have any questions please call us at 800-516-2322
More informationModular Furniture LMS. Technical environment systems Installation manual
Modular Furniture LMS Technical environment systems Installation manual Technical Environment Systems INSTALLATION MANUAL Table of Contents INTRODUCTION Full Frame, Open Frame & Upright Assembly...A Foundations...B
More informationBEN'S COUNTRY WOODSHOP SMALL MISSION TABLE Version 2
BEN'S COUNTRY WOODSHOP SMALL MISSION TABLE Version 2 Cutting & Drilling Cut 2 top rails out of 1 x 3s. Each will be 8 1/2 long. Drill 1 pocket hole on the inside bottom center. This will connect the center
More informationTIGER MOTH 120 ASSEMBLY INSTRUCTIONS
TIGER MOTH 120 ASSEMBLY INSTRUCTIONS SPECIFICATIONS Wing Span: Length: Radio: Flying Weight: 1920mm 1580mm 4 channel with 6 servos 4200g AILERON ASSEMBLY 1 Start by removing the servo cover from the bottom
More informationINSTALLATION MANUAL. All Recessed Wall-Mount Modules Front-Loading, Rear-Loading, Parcel-Only, Collection Box, Trash/Recycling Bin
INSTALLATION MANUAL All Recessed Wall-Mount Modules Front-Loading, Rear-Loading, Parcel-Only, Collection Box, Trash/Recycling Bin TABLE OF CONTENTS GENERAL INFORMATION AND ADVISORIES 3 USPS INSTALLATION
More informationSelect Lab Fixed Height Workstation
Assembly Instructions Select Lab Fixed Height Workstation Contents Important User Information.............................. 2 Safety Precautions.................................... 3 Required Tools........................................
More informationSeries 4 HV Single Monitor Lift Assembly Instructions
6703 Zinser Street Schofield, WI 54476 6/13/17 Series 4 HV Single Monitor Lift Assembly Instructions Read all the instructions before beginning. Hardware Pack # 53368 Page1 OF 6 Tools Required for Assembly:
More informationROS-APT Caucus Plinth Table with Trough Note: Details apply, however the actual configuration of your table may vary from what is depicted here.
ROS-APT Caucus Plinth Table with Trough Note: Details apply, however the actual configuration of your table may vary from what is depicted here. Parts List - Tables Tops, Top Insert Panels and Base panels
More information488 Brody Disassembly Direction
488 Brody Disassembly Direction Lighting (see page 8) Screens (see page ) Backrest (see page 4) " and " BIT HOLDERS Side Surface (see page ) T0, T0, T40 TORX Personal worksurface (see page 6) Caddy (see
More informationINSTRUCTION MANUAL MANUAL DE INSTRUCCIONES
INSTRUCTION MANUAL MANUAL DE INSTRUCCIONES Model Number/ No. de Modelo: WDB101 CLOTHES DRYER STACKING BRACKET CAUTION: BEFORE USE, PLEASE READ AND FOLLOW ALL SAFETY RULES AND OPERATING INSTRUCTIONS. Avanti
More informationAssembly Instructions
RoomScape Furniture System March 2013 - Bed Styles bed deck board bed deck board top cap top cap base glide middle side rail frame frame stacking device frame middle lower reinforcement side rail Single
More informationLinear Hook- on Worksurfaces
Linear Hook- on Worksurfaces Linear Hook-On Worksurfaces come in three depths and seven lengths. Different worksurfaces have different reqirements for installation that are outlined below. 27 inch deep
More informationCompile Installation Manual
Compile Installation Manual 07 OHSAS 800:007 ISO 900:05 ISO 400:05 Global Contract Inc. 565 Petrolia Road REVISED: FALL 07 North York, Ontario, MJ X8 Visit us on the Internet at globalcontract.com (46)
More informationInstallation Manual MODEL ANE-42
Installation Manual MODEL ANE-42 GET TO KNOW YOUR UNIT 1 2 1. CROSS BRACES 2. SIDE BRACKETS - Stud Finder - 12-14 Level - Tape Measure - Small Flathead Screwdriver Tools Needed: - Electric Drill (with
More informationAssembly Instructions
InTandem Table System November 20 InTandem Table System - Worksurface #4 x/" 4 wood screw power beam Tools Provided T-0 Extended Torx Driver T-25 Torx Driver Additional Tools Required Soft protective
More informationRange height adjustable assembly
Table of contents Digital handset operation 3 Height adjustable bench kit 4-5 Cable carrier 6 Ganging tray and ganging rail 7 Height adjustable return frame kit 8 Cable entry pole 9 24 and 30 d worksurfaces
More informationCloset System Installation Manual
Closet System Manual Thank you For choosing our Custom Closet Collection to fit all your needs Closets come fully assembled to make your project an enjoyable and satisfying experience. With quality Custom
More informationProduct must be installed as shown using the screws and brackets provided. Use of incorrect hardware could result in damage to the product.
General Notes These installation instructions are intended to be comprehensive for a typical Keyeira/Presto configuration. Your configuration may differ. If you have questions contact Geiger Customer Service
More informationNote: This assembly instruction will cover all configurations of Alloy adjustable height double bases.
Note: This assembly instruction will cover all configurations of adjustable height double bases. 1 Screw in the provided adjustable glides into each leg as shown in Figure A. Two glides per leg. Figure
More informationImportant Loading Information. Tools Required. Meridian Lateral Files Instructions
Y Meridian Lateral Files Instructions! WARNING Failure to observe stated capacities below will result in unsafe usage conditions, causing possible product damage or personal injury. Important Loading Information
More informationSTAKS. Crossover Casegoods ASSEMBLY INSTRUCTIONS
STAKS Crossover Casegoods ASSEMBLY INSTRUCTIONS Installation Sequence 1. Wall Panels a. Connector Kit Part Identification 3 b. T - 3 Panel Connection Preparation 4 c. X Panel Connection Preparation 5 d.
More informationTherma-Tru Door Gallery Setup Instructions Swing Unit with Hardware Kit - Hardware Part # MADGSWU15 (Swing Unit) Part # MADGHKSU10 (Hardware Kit)
Swing Unit with Hardware Kit - Hardware Tools Included: 4mm Allen Wrench, 6mm Allen Wrench, 8mm T-Handle Allen Wrench (1) 3/4" Drill Bit, (1) 7/32" Drill Bit and Hole Template Guide Tools Required: Phillips
More informationOctagon Greenhouse Manual
Tools Needed: -Cordless Drill (12V or higher) -#2 Square Drive Bit -Hammer -6 Step Ladder -Tape Measure -Utility knife w/ blade & hook blade -Speed Square -5/16 Wood Drill bit Little Cottage Co. PO Box
More informationv1.0 ASSEMBLY GUIDE Mia Wide Bookcase
v1.0 ASSEMBLY GUIDE Mia Wide Bookcase Components Upon unpacking your bookcase from it s delivery box, you should have the pieces shown. Follow the steps on the next pages to assemble your new bookcase.
More informationInstalling the Profile Privacy Panel. Assemble top mounting bracket. Prerequisites. Tools
Installing the Profile Privacy Panel Complete these instructions to install the Profile Privacy Panel. Privacy panels are available in various heights to match tiers and include mounting hardware for slat
More informationLocker Pedestal Installation Instructions
Locker Pedestal Installation Instructions LK-PED-INST-0314r1 Parts List Single Pedestal Back to Back Pedestal Horizontal Support Tube TS-169 Post Flange TS-190 Post Cap Fasteners Provided: #8 x ¾ round
More informationIMPORTANT: WILL NOT FIT COUNTRYMAN MODELS
Part #1410-0102-07 2 3 1 IMPORTANT: WILL NOT FIT COUNTRYMAN MODELS Apply masking tape around the bottom grille opening and across the bottom of the upper facto ry grille.. Open the hood and remove the
More informationStuff-Your-Stuff Platform Bed (Twin and Full)
Stuff-Your-Stuff Platform Bed (Twin and Full) Pre-Assembly: Please read all instructions before beginning assembly. Assembly by two people is a must. Save all packing materials until assembly is complete
More informationmedia:scape HDVC Wall Mount
Dual Shroud media:scape HDVC Wall Mount Single Shroud CAUTION Quad Shroud FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN PROPERTY DAMAGE OR PERSONAL INJURY. Triple Shroud Read the entire Assembly
More informationi f c o L INC. COMPLETE MOTORIZED GLIDE OUT ADJUSTMENTS PROCEDURE MANUAL #400011
i f c o L INC. 24076 Reedy Dr. Elkhart, IN 46514 (574)-266-5551 (Office) (574)-206-9296 (Fax) COMPLETE MOTORIZED GLIDE OUT ADJUSTMENTS PROCEDURE MANUAL #400011 The following procedures are used to acquire
More informationINSTALLATION INSTRUCTIONS SIDE BAR FORD ESCAPE & MAZDA TRIBUTE PART #
INSTALLATION INSTRUCTIONS SIDE BAR 2008-2010 FORD ESCAPE & MAZDA TRIBUTE PART # 50136 50137 PARTS LIST: 1 Driver/Left Sidebar 2 10-1.50mm x 35mm Bolt Plate 1 Passenger/Right Sidebar 2 10-1.50mm x 30mm
More informationAIR MASTER SYSTEMS INSTALLATION GUIDE TABLE OF CONTENTS
AIR MASTER SYSTEMS INSTALLATION GUIDE TABLE OF CONTENTS GENERAL INFORMATION...1 Freight Damage... 1 Repairing Paint Scratches...1 BASE CABINETS... 2 Drawer Removal and Reinstallation...2 Replacing Drawer
More informationASSEMBLY GUIDE. Mia Narrow Bookcase
ASSEMBLY GUIDE Mia Narrow Bookcase Components: Upon unpacking your bookcase from it s delivery box, you should have the pieces shown. Follow the steps on the next pages to assemble your new bookcase. Step
More informationIAC INDUSTRIES 895 BEACON STREET BREA, CA Phone (714) Fax (714) Workmaster Assembly Instructions
INDUSTRIES WORKMASTER SERIES Part #1 REV. (022011) IAC INDUSTRIES 895 BEACON STREET BREA, CA 92821-2926 Phone (714) 990-8997 Fax (714) 990-0557 www.iacindustries.com Workmaster Assembly Instructions Table
More informationWARNING: Prior to installation, turn the power off to the vending machine and unplug it from its power source. Also, make sure to level the machine.
Installation of Gum and Mint Tray for National 147, 157, 167 Important Note: Please read all instructions thoroughly before continuing with installation of kit. If you are having problems installing the
More information