Series 9000 Panel Door; In-Line, Corner and Permanent Wall Application

Transcription

1 Series 9000 Panel Door; In-Line, Corner and Permanent Wall Application 5/32" Drill Bit In-Line Corner Permanent Wall 3/16" Allen Wrench If you have a problem, question, or request, call your local dealer, or Steelcase Line 1 at 888.STEELCASE ( ) for immediate action by people who want to help you. (Outside the U.S.A., Canada, Mexico, Puerto Rico, and the U.S. Virgin Islands, call: ) Or visit our website: Steelcase Inc. Grand Rapids, MI U.S.A. Printed in U.S.A. Page 1 of 11

2 Installation of a In-Line Panel Door 1. Stick (2) strips of tape to bottom of threshold. Lift panel and place cupped area under glide of panel, both sides of threshold must be done. This will determine the correct panel spacing for doorway. NOTE: Use velcro tape on carpet and double back tape on hard surface floors. You may remove threshold cover to run cables. Cover is held on by (3) flat head screws. 2. Install sight-sound barriers on edge of end covers opposite of door swing. Remove existing end cover by first removing top trim which lifts straight up. Back off socket head screw until assembly moves approximately 1/2". This disengages cover from inner upright tabs, now lift end cover up and away from panel. NOTE: Place one sight-sound barrier on both end covers. Use same steps for both end covers. Cupped Area Velcro or Double Back Tape Threshold Cover Cover Screw Tabs Sight-Sound Barrier Slot Cover Glide Threshold Top Trim Socket Head Screw Slots Page 2 of 11

3 Set Screw Flush With Upright To Engage Cover 3. Place new end cover onto panel, lift end cover so that all slots intersect with inner upright tabs. Exert pressure downward to interlock. To complete interlock, tighten socket head screw until top of end cover is level with top of upright. NOTE: When using E9000 panels in an in-line application you will need to modify the base trim, on the hinge side, by removing a 5/16" x 2" piece as shown to create a clearance for the hinge. Then deburr. 4. Install latch plate onto proper end cover with (2) #6 x 3/8" flat head screws and install (2) hinges onto proper end cover, use (2) #10 x 1/2" flat head screws for each hinge. Top of base trim 2" 5/16" Hinge Hinge End Plate Shim Latch Page 3 of 11

4 Pin 5. Assemble cams and pin. NOTE: s are identical except for being made of different materials, make sure to use one of each for each hinge. 6. Insert cams and pin assembly between the door hinges and end cover hinges. Hang panel door, making sure that it is level and flush with top trim of the hinged panel and recessed into the side of panel. If it is not, the door is upside down. Remove and re-install correctly. Adjust latch plate with shims if necessary. Place cap plugs into ends of hinges after installation is complete. NOTE: For cleaning instruction see Directions for Series 9000 Panel Basic ( ). MARKED CAM (WITH RIB) PLAIN CAM s & Pin Hinge Cap Hinge Caps Page 4 of 11

5 Tabs Top Trim Sight-Sound Barrier Installation of a Corner Panel Door Slot Cover Socket Head Screw 1. Install sight-sound barrier on edge of end cover and corner post, opposite of door swing. Remove existing end covers from panels on each side of doorway and install new latch end cover. First, remove top trim by lifting straight up. Then back-off socket head screw until assembly moves approximately 1/2". This disengages cover from inner upright tabs. Lift end cover up and away from panel. NOTE: Place one sight-sound barrier on end cover and one on corner post. 2. Place new end cover or corner post onto panel, lift cover or post so that all slots intersect with inner upright tabs. Exert pressure downward to interlock. To complete interlock tighten socket head screw until top of end cover or corner post is level with top of upright. Slots Set Screw Flush With Upright To Engage Cover Page 5 of 11

6 Corner Post Threshold Cover 3. Stick (2) strips of tape to bottom of threshold. Lift panel, and place cupped area under glide of panel, place other end of threshold under glide of corner post. This will determine the correct panel spacing for doorway. NOTE: Use velcro tape on carpet and double back tape on hard surface floors. 4. Install latch plate onto end cover with (2) #6 x 3/8" flat head screws. Drill (6) 5/32" Dia. holes inside of corner post per dimensions shown on page 8. Install (2) hinges onto corner post. Use (3) #10 x 1/2" flat head screws per hinge. Cupped Area Velcro Or Double Back Tape Cover Screw Threshold Hinge Glide Corner Post Shim Latch Page 6 of 11

7 Pin 5. Assemble cams and Pin. NOTE: s are identical except for being made of different materials, make sure to use one of each for each hinge. 6. Insert cams and pin assembly between the door hinges and corner post hinges. Hang panel door making sure that it is level and flush with top trim of the hinged panel and recessed into the side of the panel. If it is not, the door is upside down. Remove and re-install correctly. Adjust latch plate with shims if necessary. Place cap plugs into ends of hinges after installation is complete. NOTE: For cleaning instruction see Directions for Series 9000 Panel Basic ( ). & Pins Hinge Cap Corner Post MARKED CAM (WITH RIB) PLAIN CAM Hinge Caps Page 7 of 11

8 15/32" 21/32" Installation of a Panel Door to a Permanent Wall 1. Install wall support assembly as shown in Directions Drill (6) 5/32" Dia. holes in corner post. NOTE: Drill on side opposite end cover assembly. Inside Of Door 1" 9-3/32" 2" 1" 2" 2-13/16" Page 8 of 11

9 Tabs Top Trim Sight-Sound Barrier 3. Install sight-sound barrier on edge of end cover and corner post, opposite of door swing. Remove existing end covers from panels on each side of doorway and install new latch end cover. First, remove top trim by lifting straight up. Then back-off socket head screw until assembly moves approximately 1/2". This disengages cover from inner upright tabs. Lift end cover up and away from panel. NOTE: Place one sight-sound barrier on end cover and one on corner post. 4. Place new end cover or corner post onto panel, lift cover of post so that all slots intersect with inner upright tabs. Exert pressure downward to interlock. To complete interlock, tighten socket head screw until top of end cover or corner post is level with top of upright. Slot Cover Slots Socket Head Screw Set Screw Flush With Upright To Engage Cover Page 9 of 11

10 Corner Post Threshold Cover Glide 5. Stick (2) strips of tape to bottom of threshold. Lift panel and place cupped area under glide of panel. Place other end of threshold under glide of corner post. This will determine the correct panel spacing for doorway NOTE: Use velcro tape on carpet and double back tape on hard surface floors. 6. Install latch plate onto end cover with (2) #6 x 3/8" flat head screws. Install (2) hinges onto corner post. Use (3) #10 x 1/2" flat head screws per hinge. Cupped Area Velcro Or Double Back Tape Cover Screw Threshold Hinge Corner Post Shim Latch Page 10 of 11

11 Pin 7. Assemble cams and pin. NOTE: s are identical except for being made of different materials, make sure to use one of each for each hinge assembly. 8. Insert cams and pin assembly between the door hinges and corner post hinges. Hang panel door making sure that it is level, flush with top trim of the hinged panel and recessed into the side of the panel. If it is not, the door is upside down. Remove and re-install correctly. Adjust latch plate with shims if necessary. Place cap plugs into ends of hinges after installation is complete. NOTE: For cleaning instructions see Directions for Series 9000 Panel Basic ( ). & Pins Hinge Cap Corner Post MARKED CAM (WITH RIB) PLAIN CAM Hinge Caps Page 11 of 11