Topo Freestanding Applications - Private Office

Size: px

Start display at page:

Download "Topo Freestanding Applications - Private Office"

Phyllis Cross
5 years ago
Views:

1 4 3 2 Topo Freestanding Applications - Private Office Combo Wrench If you have a problem, question, or request, call your local dealer, or Coalesse at Or visit our website: Coalesse San Francisco, California U.S.A. Printed in U.S.A. 3/8" Diameter Page 1 of 12

2 Prepare Tower Pedestal 1. Determine if you have a left hand or right hand application. 2. Attach (1) upper bracket as shown. 3. Attach (2) lower brackets as shown. (2) screws, 1/4-20 x 1/2" button head 2 Locate brackets on end of pedestal opposite tower. Rear side of pedestal 3 CAUTION: DO NOT TIP PEDESTAL ONTO TWO LEGS TO MOVE AS IT COULD CAUSE DAMAGE TO THE UNIT. (2) screws per bracket, 1/4-20 x 1/2" button head Page 2 of 12

3 4. Remove ALL drawer(s) as shown, if required. 5. Drill 3/8" diameter holes through top in desired location on LH or RH side. NOTE: PILOT HOLES ARE PROVIDED ON THE INSIDE OF THE TOP. 6. Carefully lift tower into position, aligning through holes in pedestal top with threaded inserts in bottom panel of tower. 7. Secure with hardware as shown. 8. Reinstall drawer(s), if required. Install tower flush with back of pedestal 1/2" (12.7 mm) from edge of pedestal TOP VIEW (4) 1/4" washer (4) 1/4-20 x 50 mm hex head Lift drawer box up to disengage slides from mounting brackets. FRONT VIEW (with drawer removed) Page 3 of 12

4 Desk Loop Assembly 1. Loosen set screws (4 ) places and remove top horizontal loop. 2. Slide full-panel infill up and out of center track and retain Full-Panel Infill Page 4 of 12

5 3. Remove backer from double-sided tape on sill assembly, then attach onto desk-loop fence track. Make sure mating surfaces are clean. 4. Install table source PVD module and wire manager per Wiremold installation instruction No (optional). PVD Module Wire Manager 4 Locate PVD module 9" from front edge of sill 3 Fit sill extrusion into fence track Sill Assembly Double-sided Tape Fence END VIEW Page 5 of 12

6 5. Replace full-panel infill into center tracks. 6. Prep desk loop sliding panel. Install infill in center track Sliding Panel Page 6 of 12

7 7. Remove forward corner casting of top loop. 8. Slide panel into forward track. END VIEW 7 Sliding Panel 8 (3) preinstalled infill extrusions (3) Rollers with panel Page 7 of 12

8 9. Reassemble and install top horizontal loop (with sliding panel, if applicable). 10. Preassemble (2) pedestal connection brackets. Loosely preassemble T-nut and bolt Loosely install bracket assemblies in bottom track of desk loop. Hint: Preassemble T-nut to bolt loosely to ease alignment to the fence channel. 9 (1) screw, 1/4-20 x 5/8" button head (2) screws, 1/4-20 x 1/2" button head Tighten screws after completing step 11 T-Nut SIDE VIEW showing T-nut and bolt loosely preassembled T-Nut will fit in channel Page 8 of 12

9 Install Desktop to Desk Loop NOTE: TETHER BRACKETS AND HYPER-GLIDE ARE PACKED WITH THE ADJUSTABLE HEIGHT COLUMN. (2) BRACKETS ARE REQUIRED FOR 6' AND 7' LOOPS, (3) BRACKETS FOR 8' LOOP. 1. Loosely preassemble the tether table brackets to the fence in the approximate locations shown. 2. Adjust tether brackets and adjustable column leg to desired height. 1a 7' Desk Loop shown here Loosen screw to adjust column 1b 1c 1d Adjustable Column Leg 2 T-Nut Tether Clip 1/4-20 X 1/2" Screw Page 9 of 12

10 3. Attach telescoping hyper-glide to underside of desktop. 4. Position desktop on center relative to desk loop. 5. Tighten tether brackets to fence. 3 (4) wood screws, #10 x 3/4" 6. Secure desktop to adjustable column leg. Underside of desktop Worksurface (2) screws per bracket #10-10 x 1-1/16" (6) wood screws #12 x 1" pan head #3 Page 10 of 12

11 Freestanding Desktop and Desk Loop Application In a freestanding application, align desktop with desk loop. Do not flex desktop relative to desk loop in a freestanding application. Page 11 of 12

12 Install Pedestal to Desk-Loop Assembly 1. Determine amount of pedestal flex relative to desk-loop, based on application. 2. Move pedestal into position under desktop. Note: Make sure pedestal and desk-loop are level before tightening brackets. SIDE VIEW showing T-nut and bolt loosely preassembled T-Nut (1) screw, 1/4-20 x 1/2" button head 4 Bottom of fence 3. Secure loop-to-ped brackets to lower brackets on bottom rear of pedestal. 4. Fasten top loop-to-ped bracket in track on bottom of fence Bottom view showing loop-to-ped brackets attached to lower brackets on pedestal. Page 12 of 12

13 Topo Biplane Assembly Instructions CAUTION: Before moving this product, make sure to disconnect at storage unit. Failure to do so may cause personal injury or property damage. 5/32" BALL TIP 1/8" If you have a problem, question, or request, call your local dealer, or Coalesse at Or visit our website: Coalesse San Francisco, California U.S.A. Printed in U.S.A. 7/16" SOCKET Page 1 of Rev D

14 1. Pull drawer forward from the pedestal (1a). Push tab on each side of the drawer rail (1b). Remove file drawer completely then remove box drawer. Push slide rails back into pedestal. 2. Remove inner screws and loosen outer screws on trim piece (2a) then remove trim piece from pedestal (2b) and save screws. NOTE: Depending on your installation, you will need to clarify which trim piece to remove (left or right hand). LOOSEN SCREW 2a REMOVE SCREW REMOVE SCREW LOOSEN SCREW PEDESTAL FILE DRAWER DEPRESS QUICK- RELEASE TAB 2b 1b 1a TRIM PIECE Page 2 of Rev D

15 3. Insert the pedestal attachment bracket where the trim piece was (3a). Use the same screws that held the trim piece to secure the new pedestal attachment bracket (3b). Place drawers back into pedestal. 4. Turn the worksurface upside down. TIP: Place the notched end of the worksurface near the pedestal as shown. 4 3a NOTCHED END FACING TOWARD PEDESTAL PEDESTAL ATTACHMENT BRACKET 3b SCREWS SAVED FROM ORIGINAL TRIM REMOVAL Page 3 of Rev D

16 5. Attach the base (5a) and hyperglide (5b). Install cams to the correct depth by pushing the cam to the bottom of the hole (there are two different depths) and in the correct orientation (with arrow pointing in the direction of the corresponding hole) (5c). Attach modesty panel (if you have one) (5d) and the PVD box (5e). You will not be able to use the fasteners that attach to the backsplash at this point. PVD BOX BASE 5d 5e 5a HYPERGLIDE 5b MODESTY PANEL 5c Page 4 of Rev D

17 NOTE: Adjust hyperglide to contact the top of the storage unit. a SLOT SLOT b a 6. Place the t-nuts onto the pedestal attachment bracket loosely and orient as shown (6a). Flip workstation onto pedestal attachment bracket (6b). The tube ends of the clamp and t-nuts should fit into the slots in the rails: A to A and B to B (6c). Slide pedestal along rails to desired location. Lift and turn t-nuts 90 then tighten. 6c b b a b a PEDESTAL 6a PEDESTAL ATTACHMENT BRACKET 6b a b T-NUT Page 5 of Rev D

18 NOTE: If a power strip has been ordered, install per the installation instructions with the power strip before step Insert dowels (lightly hammer into place) and pins into holes on backsplash (7a). Align the backsplash with rear of worksurface (7b). Locate cams underneath back of worksurface and turn each about a 1/2 turn clockwise to secure backsplash to worksurface (7c). 8. Drive remaining screw for PVD box into backsplash. TIP: Remaining screw may require the use of a hand phillips screwdriver to tighten. BACKSPLASH VIEW LOOKING UNDERNEATH REAR OF WORKSURFACE 7a DOWEL 7b PIN BACKSPLASH 7c CAM 8 Page 6 of Rev D

19 TOP VIEW OF DESK 9. Slide PVD shelf into fixed shelf assembly (9a). Align entire shelf assembly with worksurface and feed bolts through (9b). Check height of PVD shelf relative to the fixed shelf. If uneven, loosen bolts on bushings, make appropriate adjustments to the height and retighten bolts (9c). Secure bolts to the fixed shelf assembly from underneath worksurface using two (2) hex flange nuts (9d). Locate PVD shelf relative to fixed shelf by aligning front (9e) and secure remaining bolts to the PVD shelf from underneath worksurface using two (2) hex flange nuts (9f). Do not over tighten. Reach under PVD top and place provided bumpers on PVD shelf bracket as shown (9g). NOTE: You may need to adjust workstation to its longest length in order to access the hex flange nuts. FIXED SHELF ASSEMBLY 9b 9a PVD SHELF 9e FIXED SHELF ASSEMBLY ALIGN ALIGN PVD SHELF REDUCE GAP BOLTS TO LOOSEN 9g VIEW LOOKING UNDERNEATH REAR WORKSURFACE 9c 9f 9d HEX FLANGE NUT Page 7 of Rev D

20 10a 10b 10. Adjust table to desired height by locating each clamp on the pedestal attachment bracket and performing steps 10a through 10d. Place level onto worksurface (10e). Lift table and spin leg clockwise to extend or counter-clockwise to retract. Repeat on extension. 10c 10d 10e Page 8 of Rev D

21 Attaching the Worksurface Extension BASE MOUNTING BRACKET 1. Turn the extension worksurface upside down. TIP: Place the extension worksurface near the base with the counterbored holes towards the worksurface as shown. 2. Attach the base. 3. Attach the mounting bracket to the underside of the workstation as shown. 4. Turn the extension worksurface assembly upright and install the tite-joint fasteners per the hardware manufacturer's instructions. 2 3 WORKSTATION 5. Attach the extension worksurface into position by inserting two (2) screws through the mounting bracket and into the pilot holes on the underside of the extension worksurface. EXTENSION WORKSURFACE WORKSTATION EXTENSION WORKSURFACE 5 Page 9 of Rev D

22 2 MOUNTING BRACKET Attaching the Storage Extension Worksurface 1. Turn the storage extension worksurface upside down. TIP: Place the storage extension worksurface near the base with the counterbored holes towards the worksurface as shown. 2. Attach the mounting bracket to the underside of the workstation as shown. 3. Turn the storage extension worksurface assembly upright and install the tite-joint fasteners per the hardware manufacturer's instructions. 1 WORKSTATION 4. Attach the storage extension worksurface into position by inserting two (2) screws through the mounting bracket and into the pilot holes on the underside of the storage extension worksurface. STORAGE EXTENSION WORKSURFACE STORAGE EXTENSION WORKSURFACE WORKSTATION Page 10 of Rev D

Workbench Instructions for Assembly

Workbench Instructions for Assembly Technical Electronic Workstations and Industrial Workbenches Includes: Cabinets Privacy Panels Stringers Bottom Shelves Table of Contents Tools Required for Assembly...