InFrame TM Interior Framing System

Transcription

1 JANUARY, 2017 InFrame TM Interior Framing System FEATURES 1 Features x 6" sightline, interior partition framing Flush glazed, center plane glass application Screw spline fabrication 1/8", 1/4", and 3/8" infill options Permanodic TM anodized finishes in seven choices Painted finishes in standard and custom choices Product Applications Interior framing system Integrated entrance framing allowing Kawneer standard entrances or other specialty entrances to be incorporated For specific product applications, Consult your Kawneer representative.

2 2 InFrame TM Interior Framing System JANUARY, 2017 BLANK PAGE

3 JANUARY, 2017 InFrame TM Interior Framing System INDEX 3 Architects - Most extrusion and window types illustrated in this catalog are standard products for Kawneer. These concepts have been expanded and modified to afford you design freedom. Some miscellaneous details are non-standard and are intended to demonstrate how the system can be modified to expand design flexibility. Please contact your Kawneer representative for further assistance. BASIC FRAMING MEMBERS... 4 ENTRANCE FRAMING MISCELLANEOUS FRAMING... 7 LAWS AND BUILDING AND SAFETY CODES GOVERNING THE DESIGN AND USE OF GLAZED ENTRANCE, WINDOW, AND CURTAIN WALL PRODUCTS VARY WIDELY. KAWNEER DOES NOT CONTROL THE SELECTION OF PRODUCT CONFIGURATIONS, OPERATING HARDWARE, OR GLAZING MATERIALS, AND ASSUMES NO RESPONSIBILITY THEREFOR. Metric (SI) conversion figures are included throughout these details for reference. Numbers in parentheses ( ) are millimeters unless otherwise noted. The following metric (SI ) units are found in these details: m meter cm centimeter mm millimeter s second Pa pascal MPa megapascal

4 4 InFrame TM Interior Framing System JANUARY, 2017 BASIC FRAMING DETAILS SCALE 3" = 1'-0" 4 4 Note: snap-in stop with gasket can be mitered at these corners. 19/ /8" (9.5) 1" (25.4) OPP. ELEVATION IS NUMBER KEYED TO DETAILS ' FRAMING MAX. HEIGHT /3 4 HEAD 1 JAMB 17/3 7 PARTITION SILL /3 1" 1-1/8" (25.4) (28.6) 3/8" (9.5) 1/4" (6.4) INTERMEDIATE VERTICAL /4" (6.4) 5 INTERMEDIATE HORIZONTAL 6 STANDARD SILL 3 STACK INTERMEDIATE VERTICAL 17/3 19/3

5 JANUARY, 2017 InFrame TM Interior Framing System ENTRANCE FRAMING DETAILS 5 SCALE 3" = 1'-0" A 1 OPP. 7 9 ELEVATIONS ARE NUMBER KEYED TO DETAILS Note: snap-in stop with gasket can be mitered at these corners ' FRAMING MAX. HEIGHT. SEE DOOR SECTIONS FOR MAX HEIGHT 17/3 10 HEAD AT DOOR /3 1-1/16" (27) 5/16" (7.9) /3 8 DOOR JAMB 5/16" (7.9) 1-1/16" (27) 8A DOOR JAMB 17/3 9 DOOR JAMB

6 6 InFrame TM Interior Framing System JANUARY, 2017 ENTRANCE FRAMING DETAILS 19/3 SCALE 3" = 1'-0" OPP A 15B OPP. ELEVATION IS NUMBER KEYED TO DETAILS 5/16" (7.9) 1-1/16" (27) 12' FRAMING MAX. HEIGHT. SEE DOOR SECTIONS FOR MAX HEIGHT Note: snap-in stop with gasket can be mitered at these corners. 1-1/4" (31.8) 1-1/4" (31.8) 17/ /3 14 HEAD / TRANSOM AT COMMON STRIKE JAMB 1" (25.4) 3/8" (9.5) 17/3 1-1/4" (31.8) 13 TRANSOM JAMB 12 COMMON STRIKE JAMB ABOVE TRANSOM 11 COMMON STRIKE JAMB (OFFSET PIVOT ONLY) TRANSOM BAR WITH C.O.C. OR STD. SURFACE CLOSER 15A ALTERNATE BAR WITH C.O.C. FOR L.C.N. CLOSER 15B ALTERNATE TRANSOM BAR WITH C.O.C. FOR STD. KAWNEER CLOSER

7 JANUARY, 2017 InFrame TM Interior Framing System MISCELLANEAOUS FRAMING " (101.6) 1/4" (6.4) ALTERNATE HEIGHT SILL

8 8 InFrame TM Interior Framing System JANUARY, 2017 BLANK PAGE