EMC test report AU01+E04

Transcription

1 Customer: Altuflevskoye shosse,h.48,bld.1pr.1,room39 Moscow, Russia EMC test report AU01+E04 This test report may not be copied or published in a part without the written authorization of the accreditation agency and/or

2 Tel.: Fax: Accreditation: Location of Testing: The technical accuracy is guaranteed through the quality management of the AU01+E04 Page 2 of 24

3 Table of contents 1. Test regulation Equipment under test Test configuration and mode of operation Measurement of radiated emission Electrostatic discharge immunity test Radiated, radio-frequency, electromagnetic field immunity test Measurement uncertainty Summary AU01+E04 Page 3 of 24

4 1. Test regulation Emission EN 55011:2009 +A1:2010 Group 1 Group 2 Class A Class B: Industrial, scientific and medical (ISM) radio-frequency - Radio disturbance characteristics - Limits and methods of measurement Group 1 contains all ISM equipment in which there is intentionally generated and/or used conductively coupled radiofrequency energy which is necessary for the internal functioning of the equipment itself. Group 2 contains all ISM equipment in which radio-frequency energy is intentionally generated and/or used in the form of electromagnetic radiation for the treatment of material, and spark erosion equipment. Class A equipment is equipment suitable for use in all establishments other than domestic and those directly connected to a low voltage power supply network which supplies buildings used for domestic purposes. Class B equipment is equipment suitable for use in domestic establishments and in establishments directly connected to a low voltage power supply network which supplies buildings used for domestic purposes AU01+E04 Page 4 of 24

5 Includes the following tests: EN 55011:2009 +A1:2010 Measurement of the conducted disturbance at mains ports in a frequency range from 150 khz to 30 MHz. Measurement of radiated disturbance in a frequency range from 30 MHz to 1 GHz. Emission in the frequency range of 2 khz: EN :2006 EN : A1:2001 Harmonic current emissions (equipment input current 16 A per phase) Limitation of voltage fluctuations and flicker in lowvoltage supply systems for equipment with rated current 16 A Deviation of regulations and standards: No AU01+E04 Page 5 of 24

6 Susceptibility EN :2006 Electrical equipment for measurement, control and laboratory use- EMC requirements - Part 1: General requirements. Includes Basic EMC Publications: EN : A1: A2:2001 Testing and measurement techniques - Electrostatic discharge immunity test. EN :2002 Testing and measurement techniques - Radiated, radio frequency, immunity test. EN :2004 Testing and measurement techniques - Electrical fast transient (EFT)/burst immunity test. EN : A1:2001 EN : A1:2001 EN : A1:2001 Testing and measurement techniques - Surge immunity test. Testing and measurement techniques - Immunity to conducted disturbances, induced by radio-frequency fields. Testing and measurement techniques - Power frequency magnetic field immunity test. EN :2004 Testing and measurement techniques - Voltage dips, short interruptions and voltage variations immunity tests. Deviation of Regulation and Standards: No AU01+E04 Page 6 of 24

7 Not applied tests: EN 55011:2009 +A1:2010 EN :2006 EN : A1:2001 Measurement of the conducted disturbance at mains ports in a frequency range from 150 khz to 30 MHz. Harmonic current emissions (equipment input current 16 A per phase) Limitation of voltage fluctuations and flicker in lowvoltage supply systems for equipment with rated current 16 A EN :2004 Testing and measurement techniques - Electrical fast transient (EFT)/burst immunity test. EN : A1:2001 EN : A1:2001 Testing and measurement techniques - Surge immunity test. Testing and measurement techniques - Immunity to conducted disturbances, induced by radio-frequency fields. EN :2004 Testing and measurement techniques - Voltage dips, short interruptions and voltage variations immunity tests. Remark: EN : A1:2001 Remark: The EUT is battery powered. Testing and measurement techniques - Power frequency magnetic field immunity test. Only for equipment containing devices susceptible to magnetic fields AU01+E04 Page 7 of 24

8 2. Equipment under test Product type: Model name: Serial number: Manufacturer: AU01+E04 Page 8 of 24

9 Photo documentation Picture 1: Equipment under test AU01+E04 Page 9 of 24

10 3. Test configuration and mode of operation Test configuration Device Model: S/N radiation & nitrate measuring device Mode of operation The EUT was tested in the following mode of operation: Settings: Applied Software: measuring None Failure criterion for test of immunity from disturbances: It was observed whether the EUT is influenced in any form or program interruptions occurred AU01+E04 Page 10 of 24

11 4. Measurement of radiated emission according to EN Group 1 Class B Procedure of radiated emission measurement: Scan with max-peak detector in 3 m CDC Final CISPR measurement with quasi peak detector on 10m open area test site Location of measurement Description Manufacturer Inventory No. CDC Albatross Projects E00026 Open area test site E00354 Measurement equipment Description Manufacturer Inventory No. ESCI (CDC) Rohde & Schwarz E00001 ESU26 Rohde & Schwarz W00002 ESCS 30 (OATS) Rohde & Schwarz E00003 VULB 9160 (CDC) Schwarzbeck E00011 VULB 9163 (OATS) Schwarzbeck E00012 Test related measurement inaccuracies have to be taken into consideration when evaluating the test results. All used test instrument as well as the test accessories are calibrated at regular intervals AU01+E04 Page 11 of 24

12 60 50 [dbµv/m] Interference Radiation Test X vertical 0 horizontal REGULATIONS: EN Group 1 Class B PEAK / CISPR TEST EQUIPMENT: R&S ESCS30 (E00003) VULB 9163 (E00013) ORDER NO.: AU01+E04 EUT: SOEKS Limited Liability Company radiation & nitrate measuring device OPERATION MODE: measuring TEST FACILITY: DATE / TIME: :58:40 2,7 C, 100%, 101kPa TEST ENGINEER: Martin Müller Frequenz [MHz] AU01+E04 OATS.E10 Picture 2: Measurement report of radiated emission AU01+E04 Page 12 of 24

13 Photo documentation Picture 3: Test setup radiated emission AU01+E04 Page 13 of 24

14 Test result The requirements according to EN Group 1 Class B are Kept Not kept Information about measurement uncertainty is on page AU01+E04 Page 14 of 24

15 5. Electrostatic discharge immunity test according to EN Location of measurement Description Manufacturer Inventory No. Shielded chamber Siemens - Matsushita E00107 Measurement equipment Description Manufacturer Inventory No. ESD 3000 EMC Partner E00040 NSG 435 Teseq E00412 VCP E00047 HCP E00048 Test related measurement inaccuracies have to be taken into consideration when evaluating the test results. All used test instrument as well as the test accessories are calibrated at regular intervals AU01+E04 Page 15 of 24

16 Test conditions Air discharge Test voltage: 2 kv test level 1 4 kv test level 2 8 kv test level 3 15 kv test level 4 kv test level x Polarity: Discharges: Discharging points: positive negative 10 discharges per polarity screws, housing slots no discharges Contact discharge Test voltage: 2 kv test level 1 4 kv test level 2 6 kv test level 3 8 kv test level 4 kv test level x Polarity: Discharges: positive negative 10 discharges per polarity Discharging points: direct: USB shield, measuring probe no discharges indirect: HCP, VCP Climatic conditions: Ambient temp.: 21,9 C Relative humidity.: 32,2 % Barometric pressure: 97 kpa AU01+E04 Page 16 of 24

17 Photo documentation Picture 4: Test setup ESD AU01+E04 Page 17 of 24

18 Test result The requirements according to EN are Kept Not kept Information about measurement uncertainty is on page 23. Operating conditions during test: Criterion A B C The equipment shall continue to operate as intended without operator intervention. No degradation of performance or loss of function is allowed below performance level specified by the manufacturer when the equipment is used as intended. The performance level may be replaced by a permissible loss of performance. If the minimum performance level or the permissible performance loss is not specified by the manufacturer, then either of these may be derived from the product description and documentation, and by what the user may reasonably expect from the equipment if used as intended. After the test, the equipment shall continue to operate as intended without operator invention. No degradation of performance or loss of function is allowed, after the application of the phenomena below a performance level specified by the manufacturer, when the equipment is used as intended. The performance level may be replaced by a permissible loss of performance. During the test, degradation of performance is allowed. However, no change of operating state or stored data is allowed to persist after the test. If the minimum performance level (or the permissible performance loss) is not specified by the manufacturer, then either of these may be derived from the product description and documentation, and by what the user may reasonably expect from the equipment if used as intended. Loss of function is allowed, provided the function is self-recoverable, or can be restored by the operation of the controls by the user in accordance with the manufacturer s instructions. Functions, and/or information stored in non-volatile memory, or protected by a battery backup, shall not be lost. Comments: During the test the function of the EUT was observed. Influences in any form or program interruptions did not occur AU01+E04 Page 18 of 24

19 6. Radiated, radio-frequency, electromagnetic field immunity test according to EN Location of measurement Description Manufacturer Inventory No. Anechoic chamber E00100 Measurement equipment Model Description Manufacturer Inventory VULB 9163 Antenna MHz Schwarzbeck E00013 BBHA 9120E Antenne MHz Schwarzbeck E00018 SMT06 Signal Generator Rohde & Schwarz E00036 COSF 3312 Power Switching Unit Conformitas E00037 NRVD Power Meter Rohde & Schwarz E00038 AS /30 Amplifier 1-4GHz Milmega E00070 BTA W Amplifier 9 khz-220 MHz Bonn E00071 BLWA W Amplifier MHz Bonn E00072 NRV-Z51 Power Measuring Head Rohde & Schwarz E00075 NRV-Z51 Power Measuring Head Rohde & Schwarz E00076 Test related measurement inaccuracies have to be taken into consideration when evaluating the test results. All used test instrument as well as the test accessories are calibrated at regular intervals AU01+E04 Page 19 of 24

20 Test Conditions Frequency range: 80 MHz MHz with test level MHz MHz with test level MHz MHz with test level 1 Step size: 1 % of output frequency 4 % of output frequency Field strength: 1 V/m test level 1 3 V/m test level 2 10 V/m test level 3 V/m test level x Modulation: Kind of Modulation: AM Modulation factor: 80 % Modulation frequency: 1 khz Dwell time: 3 seconds X seconds Antenna polarization: Test distance: EUT position: Observation of EUT: vertical horizontal 1 m 3 m front side rear side left side right side top bottom Via video camera Climatic conditions: Ambient temp.: 21,9 C Relative humidity.: 32,2 % Barometric pressure: 97 kpa AU01+E04 Page 20 of 24

21 Photo documentation Picture 5: Test setup radiated immunity test AU01+E04 Page 21 of 24

22 Test result The requirements according to EN are Kept Not kept Information about measurement uncertainty is on page 23. Operating conditions during test: Criterion A B C The equipment shall continue to operate as intended without operator intervention. No degradation of performance or loss of function is allowed below performance level specified by the manufacturer when the equipment is used as intended. The performance level may be replaced by a permissible loss of performance. If the minimum performance level or the permissible performance loss is not specified by the manufacturer, then either of these may be derived from the product description and documentation, and by what the user may reasonably expect from the equipment if used as intended. After the test, the equipment shall continue to operate as intended without operator invention. No degradation of performance or loss of function is allowed, after the application of the phenomena below a performance level specified by the manufacturer, when the equipment is used as intended. The performance level may be replaced by a permissible loss of performance. During the test, degradation of performance is allowed. However, no change of operating state or stored data is allowed to persist after the test. If the minimum performance level (or the permissible performance loss) is not specified by the manufacturer, then either of these may be derived from the product description and documentation, and by what the user may reasonably expect from the equipment if used as intended. Loss of function is allowed, provided the function is self-recoverable, or can be restored by the operation of the controls by the user in accordance with the manufacturer s instructions. Functions, and/or information stored in non-volatile memory, or protected by a battery backup, shall not be lost. Comments: During the test the function of the EUT was observed. Influences in any form or program interruptions did not occur AU01+E04 Page 22 of 24

23 7. Measurement uncertainty Standard Description Max. deviation k= EN EN Conducted emission AMN (150kHz to 30 MHz) Radiated emission open field (30 MHz to 300 MHz) (300MHz to 1 GHz) +/- 4,1 db 2 +/- 5,4 db +/- 4,7 db EN ESD inside specification * 2 EN Radiated immunity +/- 1,8 db a.) 1,64 EN Burst inside specification * EN Surge inside specification * EN EN Conducted immunity with CDN (150 khz to 230 MHz) Conducted immunity with BCI (150 khz to 230 MHz) +/- 2,4 db b.) 1,64 +/- 2,4 db c.) 1,64 EN Magnetic field +/- 0,9 db 2 EN Dips inside specification * 2 EN Harmonic currents +/- 0,2 % d.) 1 EN Flicker annotation e.) Comment: The uncertainty stated is the expanded uncertainty obtained by multiplying the standard uncertainty by the coverage factor k. If k=2 the value of the measurands lies within the assigned range of values with a probability of 95 %. * The specific requirements regarding to the standard was kept a.) To maintain the claimed test level with a probability of 90 % an additional test level of 38 % percent must be added. b.) To maintain the claimed test level with a probability of 90 % an additional test level of 35 % percent must be added. c.) To maintain the claimed test level with a probability of 90 % an additional test level of 39 % percent must be added. d.) Measuring uncertainty (current): +/- 0,2% (fundamental oscillation), +/- 0,2% (rated current), voltage metering +/- 0,2% of the reading. Impacts on the measuring system by the EUT are not included. e.) Measuring uncertainty (flicker): dc and dmax +/- 5%, Pst +/- 8%. Impacts on the measuring system by the EUT are not included AU01+E04 Page 23 of 24

24 8. Summary The EMC regulations according to the marked specifications are Kept The Equipment under Test fulfills the general approval requirements mentioned. Not kept The Equipment under Test does not fulfill the general approval requirements mentioned. Straubing, January 21 st, 2014 Martin Müller Test engineer Christian Kiermeier Technical executive AU01+E04 Page 24 of 24