ETSI EN V2.2.0 ( ) ETSI EN V2.1.1 ( ) TEST REPORT. United GULF GATE Co.

Transcription

1 ETSI EN V2.2.0 ( ) ETSI EN V2.1.1 ( ) TEST REPORT For United GULF GATE Co. Aladel Tower,F21,Fahad Al Salem St., State of KUWAIT Model: XT-10P Report Type: Amended Report Product Type: IP Video Intercom Report Number: RXM A1 Report Date: Reviewed By: Test Laboratory: Jerry Zhang EMC Manager Bay Area Compliance Laboratories Corp. (Dongguan) No.69 Pulongcun, Puxinhu Industry Area, Tangxia, Dongguan, Guangdong, China Tel: Fax: Note: This test report is prepared for the customer shown above and for the device described herein. It may not be duplicated or used in part without prior written consent from Bay Area Compliance Laboratories Corp. (Dongguan).

2 TABLE OF CONTENTS DOCUMENT REVISION HISTORY... 3 GENERAL INFORMATION... 4 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT)... 4 OBJECTIVE... 4 TEST METHODOLOGY... 4 SYSTEM TEST CONFIGURATION... 5 DESCRIPTION OF TEST CONFIGURATION... 5 EQUIPMENT MODIFICATIONS... 5 EUT EXERCISE SOFTWARE... 5 BLOCK DIAGRAM OF TEST SETUP... 5 SUPPORT EQUIPMENT LIST AND DETAILS... 7 SUPPORT CABLE LIST AND DETAILS... 7 TEST EQUIPMENT LIST... 8 ENVIRONMENTAL CONDITIONS... 8 SUMMARY OF TEST RESULTS ENCLOSURE OF ANCILLARY EQUIPMENT MEASURED ON A STAND ALONE BASIS MEASUREMENT UNCERTAINTY TEST SYSTEM SETUP EMI TEST RECEIVER SETUP TEST PROCEDURE CORRECTED AMPLITUDE & MARGIN CALCULATION TEST DATA RADIO FREQUENCY ELECTROMAGNETIC FIELDS (80 MHZ TO MHZ) TEST SYSTEM SETUP TEST LEVEL PERFORMANCE CRITERION: A TEST PROCEDURE TEST DATA ELECTROSTATIC DISCHARGES TEST SYSTEM SETUP TEST LEVEL PERFORMANCE CRITERION: B TEST PROCEDURE TEST DATA EXHIBIT A EUT PHOTOGRAPHS EXHIBIT B TEST SETUP PHOTOGRAPHS BELOW IS THE ORIGINAL REPORT ETSI EN &3 Page 2 of 36

3 DOCUMENT REVISION HISTORY Revision Number Report Number Description of Revision Date of Revision 0 RXM Original Report RXM A1 Amended Report Note: This is the amended report application basing on the original report. The differences between them as following: 1) Changed the applicant to : United GULF GATE Co. (Address: Aladel Tower,F21,Fahad Al Salem St., State of KUWAIT). 2) Changed the product name to: IP Video Intercom. 3) Changed the model name to: XT-10P. 4) Changed the trade name to: Xontel. 5) For the appearance, changed the silk-screen of trade name and the label. The changes between the original device and the current one are stated and guaranteed by the applicant, the differences between them will affect the test results. We will update the related test results, test photos and EUT photos. ETSI EN &3 Page 3 of 36

4 GENERAL INFORMATION Product Description for Equipment under Test (EUT) EUT Name: IP Video Intercom EUT Model: XT-10P Rated Input Voltage: DC 12V or PoE External Dimension: 102mm (L)*161.5mm (W)*38mm (H) Serial Number: EUT Received Date: Objective This report is prepared on behalf of United GULF GATE Co. in accordance with ETSI EN V2.2.0 ( ) ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 1: Common technical requirements; Harmonised Standard covering the essential requirements of article 3.1(b) of Directive 2014/53/EU and the essential requirements of article 6 of Directive 2014/30/EU; ETSI EN V2.1.1 ( ) ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 3: Specific conditions for Short-Range Devices (SRD) operating on frequencies between 9 khz and 246 GHz. The objective is to determine the compliance of EUT with: ETSI EN V2.2.0 ( ) ETSI EN V2.1.1 ( ) Test Methodology All measurements contained in this report were conducted with ETSI EN V2.2.0 ( ) ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 1: Common technical requirements; Harmonised Standard covering the essential requirements of article 3.1(b) of Directive 2014/53/EU and the essential requirements of article 6 of Directive 2014/30/EU. ETSI EN &3 Page 4 of 36

5 SYSTEM TEST CONFIGURATION Description of Test Configuration Test Mode M1 M2 Adapter supply & talking PoE supply & talking Equipment Modifications No modification was made to the EUT. EUT Exercise Software No EUT software for testing. Block Diagram of Test Setup M1: 1.0 Meter ETSI EN &3 Page 5 of 36

6 M2: 1.0 Meter ETSI EN &3 Page 6 of 36

7 Support Equipment List and Details Manufacturer Description Model Serial Number TOTOLINK PoE G POE100 N/A TP-LINK Exchanger TL-SF1008P 114A Schneider Relay RXM2LB2BD N/A AKUVOX Door Phone C313 N/A Gouldin Switch Button N/A N/A CWT Adapter 2ABB018F N/A Support Cable List and Details Cable Description Shielding Type Ferrite Core Length (m) From RJ45 Cable No No 5 RJ45 Port of EUT Door Phone Signal Cable No No 5 Door Port of EUT Switch Button Signal Cable No No 5 RS485 Port of EUT Exchanger Signal Cable No No 5 Relay Port of EUT Relay Power Cable No No 1.4 Power Port of EUT Adapter RJ45 Cable No No 1 RJ45 Port of EUT PoE RJ45 Cable No No 5 RJ45 Port of PoE Door Phone To ETSI EN &3 Page 7 of 36

8 Test Equipment List Manufacturer Description Model Serial Number Calibration Date Calibration Due Date Sunol Sciences Antenna JB3 A R&S EMI Test Receiver ESCI HP Amplifier 8447D 2727A N/A Coaxial Cable C-NJNJ-50 C N/A Coaxial Cable C-NJNJ-50 C N/A Coaxial Cable C-NJNJ-50 C ETS-Lindgren Horn Antenna Agilent Spectrum Analyzer E4440A SG N/A Coaxial Cable C-SJSJ-50 C MITEQ Amplifier AFS S Farad Test Software EZ-EMC V N/A N/A HP Signal Generator 8665B 3438a Sunol Sciences Antenna JB3 A AR Power Amplifier 100W1000M N/A N/A AR Power Amplifier 60S1G N/A N/A SCHAFFNER ESD Tester NSG * Statement of Traceability: Bay Area Compliance Laboratories Corp. (Dongguan) attests that all calibrations have been performed, traceable to National Primary Standards and International System of Units (SI). Environmental Conditions Temperature: 25.1~25.9 o C Relative Humidity: 49~59%* ATM Pressure: Tester: 100.7~101kPa Redick Zhang Test Date: ~ Note: *The relative humidity of ESD test environment is 53%. ETSI EN &3 Page 8 of 36

9 SUMMARY OF TEST RESULTS SN Rule and Clause Description of Test Test Result EN Clause 8.2 EN Clause 8.3 EN Clause 8.4 EN Clause 8.5 EN Clause 8.6 EN Clause 8.7 EN Clause 9.2 EN Clause 9.3 EN Clause 9.4 EN Clause 9.5 EN Clause 9.6 EN Clause 9.7 EN Clause 9.8 Enclosure of ancillary equipment measured on a stand alone basis DC power input/output ports AC mains power input/output ports Harmonic current emissions (AC mains input port) Voltage fluctuations and flicker (AC mains input port) Wired network ports Radio frequency electromagnetic fields (80 MHz to MHz) Electrostatic discharges Fast transients, common mode Radio frequency, common mode Transients and surges in the vehicular environment Voltage dips and short interruptions Surges Note: Not applicable*: Test voltage is AC 230V/50Hz. Not applicable**: EUT power is less than 75w. Not applicable***: EUT is not equipment intended for vehicular use. Compliance*:Please refer to the report No.RDG Compliance Not applicable* Compliance* Not applicable** Compliance* Compliance* Compliance Compliance Compliance* Compliance* Not applicable*** Compliance* Compliance* ETSI EN &3 Page 9 of 36

10 1 ENCLOSURE OF ANCILLARY EQUIPMENT MEASURED ON A STAND ALONE BASIS Measurement Uncertainty Compliance or non- compliance with a disturbance limit shall be determined in the following manner: If U lab is less than or equal to U cispr of Table 1, then: compliance is deemed to occur if no measured disturbance level exceeds the disturbance limit; non - compliance is deemed to occur if any measured disturbance level exceeds the disturbance limit. If U lab is greater than U cispr of Table 1, then: compliance is deemed to occur if no measured disturbance level, increased by (U lab U cispr ), exceeds the disturbance limit; non - compliance is deemed to occur if any measured disturbance level, increased by (U lab U cispr ), exceeds the disturbance limit. Based on CISPR : 2011, measurement uncertainty of radiated emission at a distance of 10m at Bay Area Compliance Laboratories Corp. (Dongguan) is:30m~200mhz: 4.55 db for Horizontal, 4.57 db for Vertical; 200M~1GHz: 4.66 db for Horizontal, 4.56 db for Vertical; measurement uncertainty of radiated emission at a distance of 3m at Bay Area Compliance Laboratories Corp. (Dongguan) is:30m~200mhz: 4.58 db for Horizontal, 4.59 db for Vertical; 200M~1GHz: 4.83 db for Horizontal, 5.85 db for Vertical; 1G~6GHz: 4.45 db, 6G~18GHz: 5.23 db Table 1 Values of U cispr Measurement Radiated disturbance (electric field strength at an OATS or in a SAC) (30 MHz to 1000 MHz) Radiated disturbance (electric field strength in a FAR) (1 GHz to 6 GHz) Radiated disturbance (electric field strength in a FAR) (6 GHz to 18 GHz) U cispr 6.3 db 5.2 db 5.5 db Test System Setup Below 1GHz: ETSI EN &3 Page 10 of 36

11 Above 1GHz: The radiated emission tests below 1GHz were performed in 10 meters, above 1GHz were performed in the 3 meters. The specification used was EN Class B limits. The external I/O cables were draped along the test table and formed a bundle 30 to 40 cm long in the middle. The spacing between the peripherals was 10 cm. EMI Test Receiver Setup The system was investigated from 30 MHz to 6 GHz. During the radiated emission test, the EMI test receiver Setup was set with the following configurations: Frequency Range RBW Video B/W IF B/W Detector 30 MHz 1000 MHz 120 khz 300 khz 120 khz QP 1MHz 3 MHz / Peak Above 1 GHz 1MHz 10Hz / Peak ETSI EN &3 Page 11 of 36

12 Test Procedure Maximizing procedure was performed on the highest emissions to ensure that the EUT complied with all installation combinations. All data was recorded in the Quasi-peak detection mode from 30MHz to 1GHz, Peak and average detection mode above 1 GHz. Corrected Amplitude & Margin Calculation The basic equation is as follows: Result = Meter Reading+ Corrected Note: Corrected = Antenna Factor + Cable Loss - Amplifier Gain or Corrected = Antenna Factor + Cable Loss + Insertion loss of attenuator - Amplifier Gain The Margin column of the following data tables indicates the degree of compliance with the applicable limit. For example, a margin of 7dB means the emission is 7dB below the limit. The equation for margin calculation is as follows: Margin = Limit Result ETSI EN &3 Page 12 of 36

13 Test Data Please refer to following table and plots: Condition: EN Polarization: Horizontal EUT: IP Video Intercom Power: AC 230V/50Hz Model: XT-10P Distance: 10m Test Mode: M1 Note: No. Frequency Reading Detector Corrected Result Limit Margin (MHz) (dbμv) db/m (dbμv/m) (dbμv/m) (db) QP QP QP QP QP QP ETSI EN &3 Page 13 of 36

14 Condition: EN Polarization: Vertical EUT: IP Video Intercom Power: AC 230V/50Hz Model: XT-10P Distance: 10m Test Mode: M1 Note: No. Frequency Reading Detector Corrected Result Limit Margin (MHz) (dbμv) db/m (dbμv/m) (dbμv/m) (db) QP QP QP QP QP QP ETSI EN &3 Page 14 of 36

15 Condition: EN Polarization: Vertical EUT: IP Video Intercom Power: AC 230V/50Hz Model: XT-10P Distance: 10m Test Mode: M2 Note: No. Frequency Reading Detector Corrected Result Limit Margin (MHz) (dbμv) db/m (dbμv/m) (dbμv/m) (db) QP QP QP QP QP QP ETSI EN &3 Page 15 of 36

16 Condition: EN Polarization: Horizontal EUT: IP Video Intercom Power: AC 230V/50Hz Model: XT-10P Distance: 10m Test Mode: M2 Note: No. Frequency Reading Detector Corrected Result Limit Margin (MHz) (dbμv) db/m (dbμv/m) (dbμv/m) (db) QP QP QP QP QP QP ETSI EN &3 Page 16 of 36

17 Condition: EN Class B(PeaK) Polarization: Horizontal EUT: IP Video Intercom Power: AC 230V/50Hz Model: XT-10P Distance: 3m Test Mode: M1 Note: No. Frequency Reading Detector Corrected Result Limit Margin (MHz) (dbμv) db/m (dbμv/m) (dbμv/m) (db) peak AVG peak AVG peak AVG ETSI EN &3 Page 17 of 36

18 Condition: EN Class B(PeaK) Polarization: Vertical EUT: IP Video Intercom Power: AC 230V/50Hz Model: XT-10P Distance: 3m Test Mode: M1 Note: No. Frequency Reading Detector Corrected Result Limit Margin (MHz) (dbμv) db/m (dbμv/m) (dbμv/m) (db) peak AVG peak AVG peak AVG ETSI EN &3 Page 18 of 36

19 Condition: EN Class B(PeaK) Polarization: Horizontal EUT: IP Video Intercom Power: AC 230V/50Hz Model: XT-10P Distance: 3m Test Mode: M2 Note: No. Frequency Reading Detector Corrected Result Limit Margin (MHz) (dbμv) db/m (dbμv/m) (dbμv/m) (db) peak AVG peak AVG peak AVG ETSI EN &3 Page 19 of 36

20 Condition: EN Class B(PeaK) Polarization: Vertical EUT: IP Video Intercom Power: AC 230V/50Hz Model: XT-10P Distance: 3m Test Mode: M2 Note: No. Frequency Reading Detector Corrected Result Limit Margin (MHz) (dbμv) db/m (dbμv/m) (dbμv/m) (db) peak AVG peak AVG peak AVG ETSI EN &3 Page 20 of 36

21 7 RADIO FREQUENCY ELECTROMAGNETIC FIELDS (80 MHZ TO MHZ) Test System Setup Anechoic Chamber d EUT System Wooden table 80 cm Power Amplifier Signal Generator Note:d=3m(below 1G)/1m(above 1G); Test Level Level Field Strength V/m X. Special Performance Criterion: A Test Procedure The EUT and its simulators are placed on a turn table which is 0.8 meter above the ground. The EUT is set 3 meters away from the Receiving antenna which is mounted on an antenna tower. Both horizontal and vertical polarizations of the antenna are set on test. Each of the four sides of EUT must be faced this Receiving antenna and measured individually. In order to judge the EUT performance, a CCD camera and C313 were used to monitor the EUT. ETSI EN &3 Page 21 of 36

22 Test Data Please refer to following tables: Test Mode: Note: M1,M2 Condition of Test Field Strength 3 V/m (Test Level 2) RF Signal 1 khz, 80% AM, sine wave Sweep Frequency Step 1%, logarithmic Dwell Time 1 Sec Remarks Frequency Range (MHz) Front Side Rear Side Left Side Right Side VERT HORI VERT HORI VERT HORI VERT HORI A A A A A A A A A A A A A A A A Test Setup Photo-M1 ETSI EN &3 Page 22 of 36

23 Test Setup Photo-M2 ETSI EN &3 Page 23 of 36

24 8 ELECTROSTATIC DISCHARGES Test System Setup Adapter EUT System ESD Tester AC Mains Wooden Table 80 Remark: is the tip of the electrode EN specifies that a tabletop EUT shall be placed on a non-conducting table which is 80 centimeters above a ground reference plane and that floor mounted equipment shall be placed on a insulating support approximately 10 centimeters above a ground plane. During the tests, the EUT is positioned over a ground reference plane in conformance with this requirement. For tabletop equipment, a 1.6 by 0.8-meter metal sheet (HCP) is placed on the table and connected to the ground plane via a metal strap with two 470 k Ohms resistors in series. The EUT and attached cables are isolated from this metal sheet by 0.5-millimeter thick insulating material. A Vertical Coupling Plane (VCP) grounded on the ground plane through the same configuration as in the HCP is used. Test Level Level Test Voltage Contact Discharge (±kv) Test Voltage Air Discharge (±kv) X. Special Special Test Level 3 for Air Discharge at ±8 kv Test Level 2 for Direct Discharge at ±4 kv Performance criterion: B ETSI EN &3 Page 24 of 36

25 Test Procedure Air Discharge: This test is done on a non-conductive surface. The round discharge tip of the discharge electrode shall be approached as fast as possible to touch the EUT. After each discharge, the discharge electrode shall be removed from the EUT. The generator is then re-triggered for a new single discharge and repeated 10 times for each pre-selected test point. This procedure shall be repeated until all the air discharge completed. Contact Discharge: All the procedure shall be same as Section of EN , except that the tip of the discharge electrode shall touch the EUT before the discharge switch is operated. Indirect discharge for horizontal coupling plane At least 50 single discharges shall be applied to the horizontal coupling plane, at points on each side of the EUT. The discharge electrode positions vertically at a distance of 0.1m from the EUT and with the discharge electrode touching the coupling plane. Indirect discharge for vertical coupling plane At least 50 single discharges shall be applied to the center of one vertical edge of the coupling plane. The coupling plane, of dimensions 0.5m X 0.5m, is placed parallel to, and positioned at a distance of 0.1m from the EUT. Discharges shall be applied to the coupling plane, with this plane in sufficient different positions that the four faces of the EUT are completely illuminated. ETSI EN &3 Page 25 of 36

26 Test Data Please refer to following tables: Test Mode: Note: M1,M2 Table 1: Electrostatic Discharge Immunity (Air Discharge) Test Points Location Test Levels -2 kv +2 kv -4 kv +4 kv -8 kv +8 kv -15 kv +15 kv Plastic Shell A A A A A A / / Port A A A A A A / / Seam A A A A A A / / Camera A A A A A A / / Table 2: Electrostatic Discharge Immunity (Direct Contact) Test Points Location Test Levels -2 kv +2 kv -4 kv +4 kv -6 kv +6 kv -8 kv +8 kv Screw A A A A Button A A A A Metal Shell A A A A / / / / RJ45 Port A A A A / / / / Table 3: Electrostatic Discharge Immunity (Indirect Contact HCP) Test Points Location Test Levels -2 kv +2 kv -4 kv +4 kv -6 kv +6 kv -8 kv +8 kv Front Side A A A A / / / / Back Side A A A A / / / / Left Side A A A A / / / / Right Side A A A A / / / / Table 4: Electrostatic Discharge Immunity (Indirect Contact VCP) Test Points Location Test Levels -2 kv +2 kv -4 kv +4 kv -6 kv +6 kv -8 kv +8 kv Front Side A A A A / / / / Back Side A A A A / / / / Left Side A A A A / / / / Right Side A A A A / / / / ETSI EN &3 Page 26 of 36

27 ESD Location Photo Air Discharge: Direct Contact: ETSI EN &3 Page 27 of 36

28 M1 Test Setup Photo M2 Test Setup Photo ETSI EN &3 Page 28 of 36

29 EXHIBIT A EUT PHOTOGRAPHS EUT All View EUT Bottom View ETSI EN &3 Page 29 of 36

30 EUT Side View EUT Label View ETSI EN &3 Page 30 of 36

31 EUT Port View ETSI EN &3 Page 31 of 36

32 EXHIBIT B TEST SETUP PHOTOGRAPHS RE Below 1G Front-M1 View RE Below 1G Rear-M1 View ETSI EN &3 Page 32 of 36

33 RE Below 1G Front-M2 View RE Below 1G Rear-M2 View ETSI EN &3 Page 33 of 36

34 RE Above 1G Front-M1 View RE Above 1G Rear-M1 View ETSI EN &3 Page 34 of 36

35 RE Above 1G Front-M2 View RE Above 1G Rear-M2 View ETSI EN &3 Page 35 of 36

36 BELOW IS THE ORIGINAL REPORT ETSI EN &3 Page 36 of 36