EMC Test Report. Report No.: AGC EE01 : VR 6600PRO, VR 6610, VR 6700, VRP 6000, VRP 6800 : VERO GLOBAL COMMUNICATION CO.

Transcription

1 Page 1 of 38 EMC Test Report PRODUCT DESIGNATION BRAND NAME MODEL NAME CLIENT : Dual Band Mobile Radio : VGC : VR 6600PRO, VR 6610, VR 6700, VRP 6000, VRP 6800 : VERO GLOBAL COMMUNICATION CO.,LTD DATE OF ISSUE : Apr.24, 2015 STANDARD(S) : REPORT VERSION : V1.0 ETSI EN V1.9.2 ( ) ETSI EN V1.2.1 ( ) Attestation of Global Compliance (Shenzhen) Co., Ltd CAUTION: This report shall not be reproduced except in full without the written permission of the test laboratory and shall not be quoted out of context.

2 Report Revise Record Page 2 of 38 Report Version Revise Time Issued Date Valid Version Notes V1.0 / Apr.24, 2015 Valid Original Report

3 TABLE OF CONTENTS Page 3 of GENERAL INFORMATION EUT DESCRIPTION TEST METHODOLOGY UNIT OF MEASUREMENT ANTENNA DECISION OF TEST MODE INSTRUMENT AND CALIBRATION MEASURING INSTRUMENT CALIBRATION FACILITIES AND ACCREDITATIONS FACILITIES EQUIPMENT SETUP OF EQUIPMENT UNDER TEST SETUP CONFIGURATION OF EUT SUPPORT EQUIPMENT TEST SETUP ETSI EN /-5 REQUIREMENTS DC MAINS LINE CONDUCTED EMISSION RADIATED EMISSION RF ELECTROMAGNETIC FIELD TRANSIENTS AND SURGES IN THE VEHICULAR ENVIRONMENT DC MAINS RF COMMON MODE APPENDIX PHOTOGRAPHS OF TEST SETUP APPENDIX PHOTOGRPHS OF EUT... 23

4 1. GENERAL INFORMATION Page 4 of 38 Applicant: Manufacturer: Product Designation: Brand Name: Model Name: Series Model Difference description VERO GLOBAL COMMUNICATION CO.,LTD No.3 Chongxiang St, Quanzhou Economic & Technological Development Zone, Fujian, P.R.C VERO GLOBAL COMMUNICATION CO.,LTD No.3 Chongxiang St, Quanzhou Economic & Technological Development Zone, Fujian, P.R.C Dual Band Mobile Radio VGC VR-6600PRO VR-6610, VR-6700, VRP-6000, VRP-6800 All the same except for the model name. Date of Test: Apr.17, 2015 to Apr.23, 2015 APPLICABLE STANDARDS STANDARD ETSI EN V1.9.2 ( ) ETSI EN V1.2.1 ( ) TEST RESULT Compliance The above equipment was tested by Attestation Of Global Compliance (Shenzhen) Co., Ltd. for compliance with the requirements set forth in ETSI EN and ETSI EN The results of testing in this report apply only to the product/system, which was tested. Other similar equipment will not necessarily produce the same results due to production tolerance and measurement uncertainties. Tested by Steven Zhou Apr.24, 2015 Checked By Kidd Yang Apr.24, 2015 Authorized By Solger Zhang Apr.24, 2015

5 2. EUT DESCRIPTION Product Designation Brand Name Model Name Hardware Version: Software Version: Operation Frequency Modulation type Operation Mode Channel Separation Antenna Designation Antenna type Antenna gain Dual Band Mobile Radio VGC VR-6600PRO N/A N/A VHF: 144~146MHz UHF: 430~440MHz F3E Push to talk 12.5 KHz, 25KHz Detachable External antenna 0dBi Page 5 of 38 Power Supply DC 13.8V Note: For more details, refer to the user s manual of the EUT.

6 3. TEST METHODOLOGY Page 6 of 38 All tests were performed in accordance with the procedure documented in ETSI EN V1.9.2 ( ) as referenced in ETSI EN V1.2.1 ( ). 3.1 UNIT OF MEASUREMENT Measurements of radiated interference are reported in terms of db(uv/m) at a specified distance. The indicated readings on the Spectrum analyzers were converted to db (uv/m) by use of appropriate conversion factors. Measurements of conducted interference are reported in terms of db(uv). The field strength is calculated by adding the Antenna Factor and Cable Factors and subtracting the Amplifier Gain from the measured reading. The following is a sample calculation: FS = RA + AF + CF - AG Where FS = Field Strength RA = Receiver Amplitude AF = Antenna Factor CF = Cable Attenuation Factor AG = Amplifier Gain Assume a receiver reading of 52.5 dbuv is obtained. The Antenna Factor of 7.4dB/m and a Cable Factor of 1.1dB are added. The Amplifier Gain of 29 db is subtracted, giving field strength of 32 dbuv/m. The 32-dBuV/m values was mathematically converted to its corresponding level in uv/m. FS = = 32 dbuv/m Note: Level in uv/m = Common Antilogarithm [(32 dbuv/m)/20] = 39.8 uv/m 3.2 ANTENNA The calibrated antennas used to sample the radiated field strength are mounted on a non-conductive, motorized antenna mast 3 meters from the leading edge of the turntable. 3.3 DECISION OF TEST MODE Mode 1 Standby Mode + (Charging) Mode 2 Operation In VHF(Transmitting +Receiving) Mode 3 Operation In UHF(Transmitting +Receiving) Note: All the modes had been test, but only the worst data was recorded in the report.

7 4. INSTRUMENT AND CALIBRATION Page 7 of MEASURING INSTRUMENT CALIBRATION The measuring equipment, which was utilized in performing the tests documented herein, has been calibrated in accordance with the manufacturer's recommendations for utilizing calibration equipment, which is traceable to recognized national standards. The uncertainty is calculated using the methods suggested in the Guide to the Expression of Uncertainty in Measurement (GUM) published by ISO. - Uncertainty of Conducted Emission, Uc = ±2.75dB - Uncertainty of Radiated Emission, Uc = ±3.2dB

8 5. FACILITIES AND ACCREDITATIONS 5.1 FACILITIES Page 8 of 38 Site Location Attestation of Global Compliance (Shenzhen) Co., Ltd B112-B113 Building 12, Baoan Building Materials Center, No.1 of Xixiang Inner Ring Road, Baoan District, Shenzhen, Guangdong, P.R.China 5.2 EQUIPMENT Radiated emissions are measured with one or more of the following types of linearly polarized antennas: tuned dipole, biconical, log periodic, bi-log, and/or ridged waveguide, horn. Spectrum analyzers with preselectors and quasi-peak detectors are used to perform radiated measurements. Conducted emissions are measured with Line Impedance Stabilization Networks and EMI Test Receivers. Calibrated wideband preamplifiers, coaxial cables, and coaxial attenuators are also used for making measurements. All receiving equipment conforms to CISPR Publication 16-1, Radio Interference Measuring Apparatus and Measurement Methods.

9 6. SETUP OF EQUIPMENT UNDER TEST Page 9 of SETUP CONFIGURATION OF EUT See test photographs attached in Appendix 1 for the actual connections between EUT and support equipment. 6.2 SUPPORT EQUIPMENT No. Device Type Brand Model FCC ID Series No. Data Cable Power Cord Notes: 1. All the equipment/cables were placed in the worst-case configuration to maximize the emission during the test. 2. Grounding was established in accordance with the manufacturer s requirements and conditions for the intended use. 6.3 TEST SETUP The equipment under test was configured and operated in a manner of normal operation. EUT tended to maximize its emission characteristics in a typical application for conducted and radiated emission measurement. The RF module plus ancillary (standalone unit) was evaluated as per table 2 of clause 7.1 of ETSI EN Operating System -- File Name -- Program Sequence -- RF Management Software -- Software Used During the Test Remark: During the test, no modification is made to the EUT to comply with Class B limit levels.

10 7. ETSI EN /-5 REQUIREMENTS Page 10 of DC MAINS LINE CONDUCTED EMISSION Please refer to ETSI EN Clause 8.4.3, Table 8 and EN Clause 5, Table 2, Class B MEASUREMENT EQUIPMENT USED Conducted Emission Test Site # 3 Name of Manufacturer Model Serial Number Calibration Date Calibration Due Equipment EMI Test Receiver R&S ESCI LISN R&S ESH3-Z Remark: Each piece of equipment is scheduled for calibration once a year. TEST CONFIGURATION Vert. reference plane EMI receiver EUT LISN Reference ground plane TEST PROCEDURE Please refer to ETSI EN Clause and EN Clause 5 for the measurement methods. TEST RESULTS (OPERATE IN MODE 2-TX)

11 Page 11 of 38 CONDUCTED EMISSION TEST LINE 1 (+12V)

12 CONDUCTED EMISSION TEST LINE 2 (-12V) Page 12 of 38

13 7.2 RADIATED EMISSION Page 13 of 38 LIMIT Please refer to EN55022 Standard. MEASUREMENT EQUIPMENT USED Radiated Emission Test Site # 4 Name of Equipment Manufacturer Model Serial Number Calibration Due EMI TEST RECEIVER RS ESCI AMPLIFIER HP HP8447D 2944A ANTENNA SCHWARZBECK VULB POSITIONING CONTROLLER MF MF-7802 MF Remark: Each piece of equipment is scheduled for calibration once a year. TEST CONFIGURATION Turntable 1m ~ 4m Power Cable EUT 0.8 m Coax ial Cable F Filter To Power 3m 1m Filter EMI Receiver Ground Plane

14 TEST PROCEDURE Please refer to EN55022 for the measurement methods. Page 14 of 38 TEST RESULTS This test is not applicable for the equipment.

15 7.3 RF ELECTROMAGNETIC FIELD Page 15 of 38 LIMIT Please refer to EN MEASUREMENT EQUIPMENT USED Radiated Electromagnetic Field immunity Measurement ( ) Name of Equipment Manufacturer Model Serial Number Calibration Due SIGNAL GENERATOR R&S E4421B ANTENNA SCHWARZBECK VULB POWER SENSOR R&S URV5-Z POWER METER R&S NRVD / POWER AMPLIFIER KALMUS 7100C N/A RF AMPLIFIER Milmega AS _ HORN ANTENNA ETS LINDGREN 3117 N/A Audio Analyzer HP 8920B 3104A Remark: Each piece of equipment is scheduled for calibration once a year. Test Configuration

16 Page 16 of 38 Ambient Condition of the Test Site Temperature 22 C EUT AC Voltage Rating N/A Humidity 50%RH EUT DC Voltage Rating DC13.8V Pressure 990 mbar Ground Bond Resistance 0.2 Ω Tested by Steven Test Condition Sweep Step: 1% Dwell Times: 3 Seconds Modulation: 400Hz/80% AM Wanted input signal 1KHZ, 60% deviation TEST PROCEDURE Please refer to ETSI EN Clause 9.2.2, ETSI EN Clause and EN for the measurement methods. TEST RESULTS During the assessment of CT and CR, the audio quality was monitored by a audio analyzer 8920B located outside the test environment. An audio generator has been used to provide necessary modulation for CT test and for CR evaluation, an RF Generator has been used to provide source. EUT Working Mode Antenna Polarity Frequency (MHz) Field Strength (V/m) Audio Distortion Observation Conclusion Operating Mode Receiving Mode H/V % CT Pass H/V % CT Pass H/V % CR Pass H/V % CR Pass Note: There was not any unintentional transmission discovered in standby mode

17 Page 17 of TRANSIENTS AND SURGES IN THE VEHICULAR ENVIRONMENT LIMIT Please refer to ISO [15] MEASUREMENT EQUIPMENT USED AC MAINS SURGES (EN ) Name of Equipment Manufacturer Model Serial Number Calibration Due Load Dump Generator EM Test LD Voltage Drop Simulator EM Test VDS Electrical Fast Transient Generator Electrical Fast Transient Generator EM Test EFT EM Test MPG Remark: Each piece of equipment is scheduled for calibration once a year. Test Configuration To DC Source Surge Immunity Test EUT & Support Units 0.8m Controller Computer Ambient Condition of the Test Site Temperature 24 C EUT AC Voltage Rating N/A Humidity 51%RH EUT DC Voltage Rating DC13.8V Pressure 990 mbar Ground Bond Resistance 0.2 Ω Tested by Steven TEST PROCEDURE

18 Page 18 of 38 Please refer to ISO [8] for the measurement methods. TEST RESULTS Results of Final Tests (Operate in Mode 3-TX+RX) Pulse Type Level Criteria Phenomenon Result(Pass/Fail) 1 III TT/TR See Note Pass 2a III TT/TR See Note Pass 2b III TT/TR See Note Pass 3a III CT/CR See Note Pass 3b III CT/CR See Note Pass 4 III TT/TR See Note Pass Note: During test, the EUT hasn t loss of function and no unintended RF-Transmission, and no loss of primary user functions. After test, the EUT can operate as intended with no loss of primary and secondary user functions, and the communication link has been maintained.

19 7.5 DC MAINS RF COMMON MODE Page 19 of 38 LIMIT Please refer to EN MEASUREMENT EQUIPMENT USED AC MAINS RF COMMON MODE (EN ) Name of Equipment Manufacturer Model Serial Number Calibration Due Power Amplifier AR 75A250A CDN Schaffner M dB attenuator JWF 50FHC N/A Power Sensor R&S URV5-Z Power Meter R&S NRVD / Signal Generator R&S SML Audio Analyzer HP 8920B 3104A Remark: Each piece of equipment is scheduled for calibration once a year. Test Configuration 10 cm isolation supporter 0.1m< L <0.3m EUT and Support units CDN Power Amplifier PC Controller Ground Reference Plane Ambient Condition of the Test Site Temperature 25 C EUT AC Voltage Rating N/A Humidity 52%RH EUT DC Voltage Rating DC13.8V Pressure 990 mbar Ground Bond Resistance 0.2 Ω Tested by Steven

20 Page 20 of 38 TEST PROCEDURE Please refer to ETSI EN Clause and EN for the measurement methods, during the assessment of CT and CR, the audio quality was monitored by the audio analyzer connect to the equipment. TEST RESULTS Results of Final Tests (OPERATE IN MODE 2) Frequency Range: 0.15MHz~80MHz Frequency Step: 1% of fundamental Dwell time: 3 Sec. Wanted input signal 1KHZ, 60% deviation 80% A.M., 400 Hz Sine wave (Voltage: 3 V) Coupling type: CDN / RF Current Probe EUT Working Mode Transmitting Mode Field Frequency Audio Test Point Strength Observation Conclusion (MHz) Distortion (Vrms) dc. port % CT Pass Receiving Mode dc. port % CR Pass Note: There was not any unintentional transmission in Standby mode

21 APPENDIX 1 PHOTOGRAPHS OF TEST SETUP CONDUCTED EMISSION TEST SETUP Page 21 of 38 CS TEST SETUP

22 TRANSIENT IMMUNITY TEST SETUP Page 22 of 38 RS IMMUNITY TEST SETUP

23 Page 23 of 38 APPENDIX 2 PHOTOGRPHS OF EUT TOTAL VIEW OF EUT TOP VIEW OF EUT

24 BOTTOM VIEW OF EUT Page 24 of 38 FRONT VIEW OF EUT

25 BACK VIEW OF EUT Page 25 of 38 LEFT VIEW OF EUT

26 RIGHT VIEW OF EUT Page 26 of 38 TOP VIEW OF ANCILLARY EQUIPMENT

27 BOTTOM VIEW OF ANCILLARY EQUIPMENT Page 27 of 38 FRONT VIEW OF ANCILLARY EQUIPMENT

28 BACK VIEW OF ANCILLARY EQUIPMENT Page 28 of 38 LEFT VIEW OF ANCILLARY EQUIPMENT

29 RIGHT VIEW OF ANCILLARY EQUIPMENT Page 29 of 38 OPEN VIEW-1 OF EUT

30 Page 30 of 38 OPEN VIEW-2 OF EUT OPEN VIEW-3 OF EUT

31 INTERNAL VIEW-1 OF EUT Page 31 of 38 INTERNAL VIEW-2 OF EUT

32 Page 32 of 38 INTERNAL VIEW-3 OF EUT INTERNAL VIEW-4 OF EUT

33 INTERNAL VIEW-5 OF EUT Page 33 of 38 INTERNAL VIEW-6 OF EUT

34 INTERNAL VIEW-7 OF EUT Page 34 of 38 INTERNAL VIEW-8 OF EUT

35 INTERNAL VIEW-9 OF EUT Page 35 of 38 INTERNAL VIEW-10 OF EUT

36 INTERNAL VIEW-11 OF EUT Page 36 of 38 INTERNAL VIEW-12 OF EUT

37 INTERNAL VIEW-13 OF EUT Page 37 of 38 INTERNAL VIEW-14 OF EUT

38 INTERNAL VIEW-15 OF EUT Page 38 of END OF REPORT---