EMC TEST REPORT for Repel-it. REPEL-IT ULTRASONIC PEST REPELLER Model No. : REPEL-IT/UPR/AN-B019

Transcription

1 Page 1 of 22 Report No E EMC TEST REPORT for Repel-it REPEL-IT ULTRASONIC PEST REPELLER Model No. : REPEL-IT/UPR/AN-B019 Applicant : Repel-it Address 168 Logan Road, Woolloongabba, Brisbane, Australia, 4102 Tel: Prepared By : Address : 1/F., Building 1, SEC Industrial Park, No.0409 Qianhai Road, Nanshan District, Shenzhen, Guangdong, China Tel: (86) Fax: (86) Report Number : E Date of Test : Nov. 12~20, 2013 Date of Report : Nov. 21, 2013

2 Page 2 of 22 Report No E TABLE OF CONTENTS Description Page Test Report Verification 1. GENERAL INFORMATION Description of Device (EUT) Description of Test Facility Measurement Uncertainty Test Summary CONDUCTED EMISSION TEST Block Diagram of Test Setup Measuring Standard Power Line Conducted Emission Limits EUT Configuration on Measurement Operating Condition of EUT Test Procedure Test Equipment Measuring Results DISTURBANCE POWER TEST Block Diagram of Test Setup Measuring Standard Disturbance Power Limits EUT Configuration on Measurement Operating Condition of EUT Test Procedure Test Equipment Disturbance Power Test Results RADIATED EMISSION TEST Block Diagram of Test Measuring Standard Radiated Emission Limits EUT Configuration on Test Operating Condition of EUT Test Procedure Test Equipment Measuring Results PHOTOGRAPH Photo of Power Line Conducted Emission Test Photo of Disturbance Power Test Photo of Radiated Emission Test...18 APPENDIX I (Photos of EUT) (3 pages)

3

4 Page 4 of 22 Report No E 1. GENERAL INFORMATION 1.1. Description of Device (EUT) EUT Model Number : REPEL-IT ULTRASONIC PEST REPELLER : REPEL-IT/UPR/AN-B019 Test Power Supply : AC240V, 50Hz Applicant : Repel-it Address 168 Logan Road, Woolloongabba, Brisbane, Australia, 4102 Manufacturer : Repel-it Address : 168 Logan Road, Woolloongabba, Brisbane, Australia, 4102 Date of receipt : Nov. 12, 2013 Date of Test : Nov. 12~20, 2013

5 Page 5 of 22 Report No E 1.2.Description of Test Facility The test facility is recognized, certified, or accredited by the following organizations: CNAS - LAB Code: L3503., Laboratory has been assessed and in compliance with CNAS/CL01: 2006 accreditation criteria for testing laboratories (identical to ISO/IEC 17025:2005 General Requirements) for the Competence of Testing Laboratories. FCC-Registration No.: , EMC Laboratory has been registered and fully described in a report filed with the (FCC) Federal Communications Commission. The acceptance letter from the FCC is maintained in our files. Registration , July 10, 2013 IC-Registration No.: 8058A-1., EMC Laboratory has been registered and fully described in a report filed with the (IC) Industry Canada. The acceptance letter from the IC is maintained in our files. Registration 8058A-1, February 22, 2013 Test Location All Emissions tests were performed:. at 1/F., Building 1, SEC Industrial Park, No.0409 Qianhai Road, Nanshan District, Shenzhen, Guangdong, China 1.3. Measurement Uncertainty Radiation Uncertainty : Ur = 4.3 db Conduction Uncertainty : Uc =3.4 db Disturbance Uncertainty : Ud = 2.6 db 1.4. Test Summary For the EUT described above. The standards used were AS/NZS CISPR 14.1: 2003 Tests Carried Out Under AS/NZS CISPR 14.1: 2003 Standard Test Items Status AS/NZS CISPR 14.1: 2013 Power Line Conducted Emission Test (150kHz To 30MHz) AS/NZS CISPR 14.1: 2013 Power disturbance(30mhz To 300MHz) AS/NZS CISPR 14.1: 2013 Radiated Emission Test (30MHz To 1000MHz) x Indicates that the test is applicable Indicates that the test is not applicable

6 Page 6 of 22 Report No E 2. CONDUCTED EMISSION TEST 2.1. Block Diagram of Test Setup Block diagram of connection between the EUT and simulators Test Receiver AC mains L.I.S.N EUT (EUT: REPEL-IT ULTRASONIC PEST REPELLER) 2.2. Measuring Standard AS/NZS CISPR 14.1: Power Line Conducted Emission Limits AS/NZS CISPR 14.1: 2013 Frequency Limit (db V) (MHz) Quasi-peak Level Average Level 0.15 ~ ~ 56.0 * 59.0 ~ 46.0 * 0.50 ~ ~ NOTE1-The lower limit shall apply at the transition frequencies. NOTE2-The limit decreases linearly with the logarithm of the frequency in the range 0.15MHz to 0.50MHz EUT Configuration on Measurement The following equipments are installed on Conducted Emission Measurement to meet AS/NZS CISPR 14.1: 2013 requirements and operating in a manner which tends to maximize its emission characteristics in a normal application REPEL-IT ULTRASONIC PEST REPELLER Model Number: REPEL-IT/UPR/AN-B019 Serial Number: N.A. Applicant : Beauty Gallery Ltd

7 Page 7 of 22 Report No E 2.5. Operating Condition of EUT Setup the EUT as shown on Section Turn on the power of all equipments Let the EUT work in measuring mode (On) and measure it Test Procedure The EUT is put on the plane 0.8m high above the ground by insulating support and connected to the AC mains through Line Impedance Stability Network (L.I.S.N). This provided a 50ohm coupling impedance for the tested equipments. Both sides of AC line are investigated to find out the maximum conducted emission according to the AS/NZS CISPR 14.1 regulations during conducted emission measurement. The bandwidth of the field strength meter (R&S Test Receiver ESCI) is set at 9kHz in 150kHz~30MHz. The frequency range from 150kHz to 30MHz is investigated for AC mains. The test results are listed in Section Test Equipment The following test equipments are used during the power line conducted emission measurement: Item Equipment Manufacturer Model No. Serial No. Last Cal. Cal. Interval 1. Two-Line Rohde & Schwarz ENV Apr. 23, Year V-network 2. EMI Test Receiver Rohde & Schwarz ESCI Apr. 23, Year 3. Compliance RF Switching Unit RSU-M Apr. 23, Year Direction 2.8. Measuring Results PASS. The frequency range 150kHz to 30MHz is investigated. The test curves are shown in the following pages.

8 Page 8 of 22 Report No E AS/NZS CISPR 14.1 CONDUCTED EMISSION TEST DATA EUT: REPEL-IT ULTRASONIC PEST REPELLER M/N: REPEL-IT/UPR/AN-B019 Operating Condition: On Test Site: 1# Shielded Room Operator: Bevan Zhang Test Specification: 264V~, 50Hz Comment: L Tem:25 Hum:50%

9 Page 9 of 22 Report No E AS/NZS CISPR 14.1 CONDUCTED EMISSION TEST DATA EUT: REPEL-IT ULTRASONIC PEST REPELLER M/N: REPEL-IT/UPR/AN-B019 Operating Condition: On Test Site: 1# Shielded Room Operator: Bevan Zhang Test Specification: 264V~, 50Hz Comment: N Tem:25 Hum:50%

10 Page 10 of 22 Report No E 3. DISTURBANCE POWER TEST 3.1. Block Diagram of Test Setup Block diagram of connection between the EUT and simulators Test Receiver AC Mains Clamp EUT (EUT: REPEL-IT ULTRASONIC PEST REPELLER) 3.2. Measuring Standard AS/NZS CISPR 14.1: Disturbance Power Limits All emanations from devices or system including any network of conductors and apparatus connected thereto, shall not exceed the level of field strengths specified below: Frequency Limits db(pw) MHz Quasi-peak Value Average Value 30 ~ Increasing Linearly with Frequency to Increasing Linearly with Frequency to EUT Configuration on Measurement The AS/NZS CISPR 14.1 Regulations test method must be used to find the maximum emission during radiated emission measurement. The configuration of the EUT is the same as used in conducted emission measurement Operating Condition of EUT Setup the EUT and simulators as shown in Section Turn on the power of all equipments Let the EUT work in test mode (On) and test it.

11 Page 11 of 22 Report No E 3.6. Test Procedure The EUT is placed on the table and away from other metallic surface at least 0.8m. It is connected to the power mains through an extension cord of 6m min. The absorber clamp clamps the cord and moves from the far end to the EUT to measure the disturbing energy emitted from the cord. The bandwidth of the test receiver(r&s ESCI) is set at 120kHz. All the test results are listed in Section Test Equipment The following test equipments are used during the disturbance power measurement: Item Equipment Manufacturer Model No. Serial No. Last Cal. Cal. Interval 1. F M Absorbing Clamp FCC Apr. 24, Year M 2. EMI Test Receiver Rohde & Schwarz ESCI Apr. 23, Year 3. Compliance RF Switching Unit RSU-M Apr. 23, Year Direction 3.8. Disturbance Power Test Results PASS. The frequency spectrum from 30 MHz to 300 MHz is investigated. Test data see the following pages.

12 Page 12 of 22 Report No E Power disturbance AS/NZS CISPR 14-1 EUT: REPEL-IT ULTRASONIC PEST REPELLER M/N:REPEL-IT/UPR/AN-B019 Operating Condition: On Test Site: 1# Shielded Room Operator: Bevan Zhang Test Specification: AC 264V 50Hz Comment: AC LINE Temp.=22.2 Hum.=60%

13 Page 13 of 22 Report No E 4. RADIATED EMISSION TEST 4.1. Block Diagram of Test Block diagram of connection between the EUT and simulators AC Mains EUT (EUT: REPEL-IT ULTRASONIC PEST REPELLER) Block diagram of test setup (In chamber) ANTENNA ELEVATION VARIES FROM 1 TO 4 METERS 3 METERS EUT System 0.8 METER GROUND PLANE (EUT: REPEL-IT ULTRASONIC PEST REPELLER) 4.2. Measuring Standard AS/NZS CISPR 14.1: Radiated Emission Limits AS/NZS CISPR 14.1: 2013 Radiated Emission Limits All emanations from a class B device or system, including any network of conductors and apparatus connected thereto, shall not exceed the level of field strengths specified below: FREQUENCY DISTANCE FIELD STRENGTHS LIMIT (MHz) (Meters) (db V/m) 30 ~

14 Page 14 of 22 Report No E 230 ~ Note: (1) The smaller limit shall apply at the combination point between two frequency bands. (2) Distance refers to the distance in meters between the measuring instrument antenna and the closed point of any part of the EUT EUT Configuration on Test The AS/NZS CISPR 14.1: 2013 regulations test method must be used to find the maximum emission during radiated emission measurement Operating Condition of EUT Turn on the power Let the EUT work in test mode (On) and measure it Test Procedure The EUT is placed on a turn table which is 0.8 meter high above the ground. The turn table can rotate 360 degrees to determine the position of the maximum emission level. The EUT is set 3 meters away from the receiving antenna which is mounted on a antenna tower. The antenna can be moved up and down from 1 to 4 meters to find out the maximum emission level. Bilog antenna (calibrated by Dipole Antenna) is used as a receiving antenna. Both horizontal and vertical polarization of the antenna are set on test. The bandwidth of the Receiver (ESCI) is set at 120kHz. The EUT is tested in 9*6*6 Chamber. The test results are listed in Section Test Equipment The following test equipments are used during the radiated emission measurement: Item Equipment Manufacturer Model No. Serial No. Last Cal. Cal. Interval 7 EMI Test Receiver Rohde & Schwarz ESPI Apr. 23, Year 8 Bilog Broadband VULB Schwarzbeck VULB9163 May 14, Year Antenna Pre-amplifier SONOMA 310N Aug. 09, Year 4.8. Measuring Results PASS. The frequency range from 30MHz to 1000MHz is investigated. Test data see the following pages.

15 Page 15 of 22 Report No E Job No.: AT E Polarziation: Vertical Standard: (RE)AS/NZS CISPR 14-1_3m Power Source: 264V~, 50Hz Test item: Radiation Test Date: 2013/11/14 Temp.( )/Hum.(%RH): 24.3( )/55%RH Time: 14:11:18 EUT: REPEL-IT ULTRASONIC PEST REPELLER Test By: Kebo Zhang Model: REPEL-IT/UPR/AN-B019 Distance: 3m Note: On

16 Page 16 of 22 Report No E Job No.: AT E Polarziation: Horizontal Standard: (RE)AS/NZS CISPR 14-1_3m Power Source: 264V~, 50Hz Test item: Radiation Test Date: 2013/11/14 Temp.( )/Hum.(%RH): 24.3( )/55%RH Time: 14:15:10 EUT: REPEL-IT ULTRASONIC PEST REPELLER Test By: Kebo Zhang Model: REPEL-IT/UPR/AN-B019 Distance: 3m Note: On

17 Page 17 of 22 Report No E 5. PHOTOGRAPH 5.1. Photo of Power Line Conducted Emission Test 5.2. Photo of Disturbance Power Test

18 Page 18 of 22 Report No E 5.3. Photo of Radiated Emission Test

19 Page 19 of 22 Report No E APPENDIX I (Photos of EUT)

20 Page 20 of 22 Report No E Figure 1 The EUT-Front View Figure 2 The EUT-Back View

21 Page 21 of 22 Report No E Figure 3 The EUT-Side View Figure 4 The EUT-Inside View

22 Page 22 of 22 Report No E Figure 5 PCB of The EUT- Front View Figure 6 PCB of The EUT- Back View