Damage Appraisal Guide for Heavy Vehicles and Equipment Heavy Vehicles and Equipment Paint Material Allowance Table June 1 st, 2017

Transcription

1 Damage Appraisal Guide for Heavy Vehicles and Equipment Heavy Vehicles and Equipment Paint Material Allowance Table June 1 st, 2017 N.B. The allowances for polyurethane paint factor in the paint materials used (polyurethane-base, varnish, primer coat, thinners, masking products, paint preparation systems (PPS), etc.). They do not take into account the cost of the infrastructure or equipment, such as paint booths, ventilation and filtrations systems, spray guns, etc. Paint Material Allowance Table. SEE Information Bulletin ATE G HOURLY RATES - POLYURETHANE PAINT CATEGORIES POLYURETHANE NO CLEAR (Single stage) POLYURETHANE WITH CLEAR (Base coat, clear coat) COLOUR GROUPS REGULAR SINGLE STAGE EA $45.66 EAH $51.12 EAM $61.66 EAW $80.10 REGULAR TWO-STAGE EB $54.02 EBH $58.00 EBM $65.49 EBW $79.08 INDUSTRIAL (Frame, tipper, heavy machinery, cistern, container, etc.) Coated part $67.13 Uncoated part (bare) $93.37 STRIPPING $38.54 SPECIAL FEATURES N.B. The appraiser must enter the vehicle colour code and colour group in the appraisal. Note 1 For the same appraisal, make a separate manual entry for each paint rate that is different, and enter the total amount, including material and labour. Also, state the number of paint hours. Example: (20hrs paint x hourly shop rate) + (20hrs x hourly paint rate $) = $ total material and labour Note 2 In addition to the regular methods used to obtain the colour group, appraisers can also check out this web site (*) : Member login: ajusteurs Steps to follow / Axalta Password: quebec (*) GAA assumes no responsibility for the web site s content. Contact the site webmaster in case of technical difficulty. Revised May 12, 2017

2

3 Paint Material Allowance Table Updated October 25, 2017 IMPORTANT The allowances for water-based paint factor in the paint materials used (paint, distilled water, clear coat, primer coat, thinners, masking products, paint preparation systems (PPS), etc.). They do not take into account the cost of the infrastructure or equipment, such as paint booths, ventilation and filtrations systems, spray guns, etc. HOURLY RATES PAINT TWO-STAGE THREE-STAGE STRIPPING $44.37 $47.73 $38.54 PAINT COMPLETE VEHICLE MAXIMUM ALLOWANCES INCLUDING BUMPERS TYPES OF VEHICLES AND LABOUR TWO-STAGE THREE-STAGE STRIPPING INTERMEDIATE OR LARGE Two-door h Four-door h Station wagon h LIGHT-DUTY TRUCKS Van no roof : deduct 4.0 h h Van with windows : add 1.0 h h Small PICKUP, shell interior not included h Large PICKUP, shell interior not included h COMPACTS Two-door h Four-door h Station wagon h SOUS-COMPACTS Two-door h Four-door h Station wagon h $1 442 $1 670 $789 $1 375 $1 599 $711 $1 309 $651 METHOD FIRST PANEL ADDITIONAL LABOUR TIME CLEAR COAT APPLICATION (*) MAJOR PANELS AND BUMPERS PARTS NOT INCLUDED IN MAJOR PANELS LIST AND SMALL PARTS WHEN THEY HAVE TO BE REPAINTED EACH ADDITIONAL PANEL MAXIMUM OPERATION INVOLVING MORE THAN ONE PART **TAKE INTO ACCOUNT OVERLAP TIME IN SOFTWARE PAINT TIME FOR THE TWO-STAGE THREE-STAGE PART TWO-STAGE (*) ADD 0.5 h ADD 0.3 h 2.5 h **1.4 h and less ADD 0.1 h ADD 0.2 h THREE-STAGE (*) ADD 1.5 h ADD 0.9 h 5.0 h **1.5 h and more ADD 0.3 h ADD 0.9 h TWO-TONE REFINISH ADD 1.0 h ADD 0.3 h 2.5 h OPERATION INVOLVING ONLY ONE PART Note 1 If a bumper can be painted separately from the car, do not consider its refinish as a second tone. Note 2 No overlap time should be considered for bumpers. Example ALLOWANCE DETAIL FOR CLEAR COAT APPLICATION TWO STAGE THREE STAGE FRONT BUMPER 0.5 h 1.5 h FRONT LEFT FENDER First part without overlap 0.5 h 1.5 h FRONT LEFT DOOR Apply overlap 0.3 h 0.9 h REAR BUMPER Do not apply overlap 0.5 h 1.5 h TOTAL CLEAR COAT APPLICATION ALLOWANCE 1.8 h 5.4 h MAXIMUM 2.5 h 5.0 h REGARDLESS OF PAINT TIME ADD 0.5 ADD 1.5 NON-MAJOR PARTS Welded radiator support Windshield pillar Roof edge Rocker panel moulding, etc. EXAMPLES SMALL PARTS (when they have to be repainted) Mouldings Mirrors Handles, etc. Revised September 8, 2017 SPECIAL FEATURES 1. BODY SIDE MOULDINGS If, given the damage, it is not necessary to refinish the lower part of the body side mouldings... deduct 2.0 h 2. FLAT BLACK REFINISH Labour allowance only. No allowance for additional material. Bumper covers excluded. Do not consider FLAT BLACK as a second tone.

4

5 Two-stage colour matching Example Audatex software 2013 KIA OptimaEX 4 DR Sedan Colour matching Paint 2.0 h Paint Software time Total: 3.1 h (1) Colour matching 1.1 h Software time Clear coat 0.3 h 0.5 h Total: 0.8 h (2) Total: 3.9 h NOTES 1. Total paint and colour matching hours must not exceed the maximum for the category. Ex.: Intermediate or Large 4DR h. 2. For each additional panel, add 0.3 h for applying the clear coat application without exceeding the maximum of 2.5 h. Revised July 20, 2015