Early Mustang & Cougar cowl repair

Size: px
Start display at page:

Download "Early Mustang & Cougar cowl repair"

Transcription

1 Early Mustang & Cougar cowl repair Okay, I m no expert but Bob suggested that I describe my experiences in replacing a rusty cowl in my 68 Mustang fastback I thought the cowl was good when I bought this Mustang, as I poured water down it and there were now leaks inside the car. Well a few years later and I m back to work on it and with some more examination I found out that it s not so good after all. Poking around with a screwdriver on the bottom of the lower cowl panel produced some small holes in it. Since the upper cowl panel is welded on the Mustangs and Cougars it s not really easy to repair, but with some work it is fixable. Since my Mustang is completely stripped to a bare shell it wasn t that big a deal like it would be with a nice running car. First off its not a small job, as the items to be removed include, the front fenders, windshield, heater box, rear fender apron to cowl extensions etc, but like I said with my car already stripped it wasn t that much more work to get at. The upper panel has to be removed and has a million (so it seems) spot welds in it. There are spot welds all around the perimeter of the upper cowl panel and another row at the top of the panel below the windshield molding. I started drilling spot welds with a special spot weld cutter - the common type with a removable cutting bit. It works pretty good on flat surfaces but not so good when the surface is uneven. I got about 2/3rds the weld cut when I started breaking the cutters and since I found out the upper cowl panel is now being reproduced I got mad and took the air chisel to the cowl side of the panel and got- er-done. Maybe one of the higher dollar spot-weld cutters that Eastwood Co. sells would be better to use, especially if you plan on trying to save and reuse your upper panel. At $150 plus shipping on the new panel it might be worth trying. Here is the upper panel I cut off. You can see the 2 rows of holes in the upper part of it. The upper holes are where it was welded to the back of the dash to make up the windshield frame and the holes just below it are where it was welded to the lower cowl panel.

2 Here is what it looks like with the upper panel removed. Notice the rusty lower panel. This was not one of Ford s better ideas and was before Quality is job 1 as from what I understand this lower panel didn t receive paint from the factory. This particular car was rust proofed when new so it did receive some coating which saved it for a long time but not forever. This closer view shows the rust holes that will wet your feet and carpet when it rains. Okay, I should have pointed out before now that you have 2 options at this time as how this is repaired properly; A left and right side repair panel that you weld in after cutting the bad sections out or a complete lower cowl panel. The two separate repair panels list for $49.95 each and the complete lower panel list for $ from CJ Pony Parts. I chose to do the two repair panels for a couple of reasons. Yes, the cost is less, but my lower cowl was solid in the center and the complete lower panel is not drilled for the wiper mounting and seemed like more work in the long run. Once the upper panel is off the next step is to cut out the bad parts of the lower cowl panel. I marked out the cutout spots by measuring off the new replacement panels. I then ground through the spot-welds on the outer edges with a 4 ½ angle grinder followed by a 3 air powered cutoff wheel to cut the rest out. Since I had planned on doing a lot of sandblasting on the cars firewall, door jams and rockers this was the time to do it since the rest of the remaining lower cowl could be sandblasted clean. Here is the sandblasted firewall and the lower cowl with the removed bad parts.

3 If you notice the drivers side windshield wiper mount still in place that s because I had not yet decided if I wanted to remove that section. I did decide later to remove it and use the whole repair panel but made sure to measure the distance center to center from the pass side mounting to make sure all lined up properly later. I found it to be less work to drill the mounting points in the repair panel then to do all the extra fitting and welding required to save the original mount. This photo shows the 2 mounting locations of the upper cowl panel, the back of the dash and the top of the lower cowl panel. The picture on the left was taken before the whole sandblasting job was done. It was cleaned up more thoroughly the next day. Once it was all blasted I sprayed the bare areas with a self-etching primer (right picture). It s now time to fit and weld in the repair panels. Here the passenger side has been welded and the welds ground down. The driver s side has been fitted and clamped in place ready to be welded in.

4 Once the mounting spot for the windshield wiper was carefully measured and the center hole made with a hole saw, I cut out a section of the original panel and bolted it in place to use as a template to drill the 3, ¼ holes needed to mount the wiper. I then removed the template and bolted 3, ¼ bolts though the holes then welded the nuts to the panel. After all welding, grinding and cleaning was done I sprayed the whole lower panel with self-etching primer. Notice the nuts welded for windshield wiper mounting.

5 After several conversations with some local body men and some consultation from our own Jan Ove I decided that the new upper panel would be secured with a body panel adhesive instead of welding it back on. This will give me a better weather tight seal and has less 'after work'. (No grinding welds down later!) The lower panel then had all the attaching points ground down to smooth bare metal and then those areas were then masked off. It was then sealed with Dupont Velvaseal and then painted with semi gloss enamel. The new upper panel was then prepped in the same manner. Note the SEM adhesive gun used to apply the body panel adhesive. The new upper panel was test fitted beforehand and a couple of screws used to locate it onto the assembly. The next step was to actually glue the panel in place. The adhesive I used was a slow setting type that bought me time to get it all in place and clamped down. It was spread out with a acid brush to make sure all bare metal was covered for corrosion resistance. Plenty of clamps were used with care taken to not clamp down too tight as per manufactures recommendations.

6 Screws were used from the underside to clamp the lower panel to the upper panel where using clamps were not possible. This is an area that I was not comfortable in getting sealed up good if it were to be welded. I feel more comfortable that it s sealed up from the elements this way. The screws would be ground off from the topside later and body filler would be use over this area later. I let this set overnight then removed the clamps and ground down any adhesive that squished out. The rear fender apron extensions (new from CJ Pony parts, another hard to save when removing item) were then welded on and the upper clamp screws ground off and body filler applied. Well here it is, primed, sanded, ready to go AND non-leaking. I think that this is a very good place to use the body panel adhesives as it saves a lot of work plug welding and grinding all the welds down when you are through.

7

Included in Hardware Kit. Jeep Cut-Out Fender Flare Set of 4 Set Part # Rev STEP 1 PRIOR TO INSTALLATION

Included in Hardware Kit. Jeep Cut-Out Fender Flare Set of 4 Set Part # Rev STEP 1 PRIOR TO INSTALLATION Jeep Cut-Out Fender Flare Set of 4 Set Part #10926-07 Rev-01 09-11-12 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the flares according to these written instructions with the hardware

More information

Part # Ford Mustang Stalker Front Bumper

Part # Ford Mustang Stalker Front Bumper Rev. 6/12 Page 1 Part # 3354 2010-2012 Ford Mustang Stalker Front Bumper Notice: Pre-fit before painting! Install new, unpainted parts according to these instructions! Then remove parts, paint them and

More information

1104. Clean up the door striker plates with a hand grinder using a wire brush and WD-40.

1104. Clean up the door striker plates with a hand grinder using a wire brush and WD-40. Chapter 31 - Misc. Putting VW Back Together (Video Clip 31) 1104. Clean up the door striker plates with a hand grinder using a wire brush and WD-40. 1105. Install both door striker plates on the VW body

More information

Body Repair. Collision Repair. Specification. Fastener Specifications Fastener Specifications. Blind Rivet. Flow Drill Screw (FDS) Torque FDS

Body Repair. Collision Repair. Specification. Fastener Specifications Fastener Specifications. Blind Rivet. Flow Drill Screw (FDS) Torque FDS Body Repair Collision Repair Specifications Fastener Specifications Fastener Specifications Application Specification Metric English Cross-Car Brace Mounting Bolts 25 Y 18 lb ft Windshield Frame Mounting

More information

Jeep. Cut-Out Fender Flares Set of 4. Included in Hardware Kit: Set Part # Rev-8 06/29/16 STEP 1 PRIOR TO INSTALLATION

Jeep. Cut-Out Fender Flares Set of 4. Included in Hardware Kit: Set Part # Rev-8 06/29/16 STEP 1 PRIOR TO INSTALLATION STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the flares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions

More information

Competition Engineering 8 Point Roll Bar (94-04 Mustang)

Competition Engineering 8 Point Roll Bar (94-04 Mustang) Competition Engineering 8 Point Roll Bar (94-04 Mustang) Required tools: Socket set / Hand tools Welder of choice Welding blankets Welding safety gear Heat gun Putty knife Bar notching tool Adjustable

More information

Cut-Out Fender Flares Rear Pair. Jeep. Included in Hardware Kit:

Cut-Out Fender Flares Rear Pair. Jeep. Included in Hardware Kit: Jeep Cut-Out Fender Flares Rear Pair STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure

More information

BMW E46 Coupe 3dr MP Bolt in (BMW Race Days Only) Roll Cage (B045) Fitting Instructions

BMW E46 Coupe 3dr MP Bolt in (BMW Race Days Only) Roll Cage (B045) Fitting Instructions BMW E46 Coupe 3dr MP Bolt in (BMW Race Days Only) Roll Cage (B045) Fitting Instructions Unwrap the mounting points/ends of the roll cage and unpack the individual fitting kits. Try to leave wrapping on

More information

MGB Sill Replacement

MGB Sill Replacement MGB Sill Replacement Monocoque structure The MGB does not have separate chassis but is designed on the monocoque principle and the sill sections are a vital part of the bodyshell structure. Because of

More information

Rust Repair Patches Made Easy

Rust Repair Patches Made Easy Rust Repair Patches Made Easy Automotive bodies have a common ailment, we all know as rust! This booklet provides you with complete and comprehensive information on how to repair rust permanently on any

More information

Mallet Painting equipment Pop rivet gun

Mallet Painting equipment Pop rivet gun RotorWay International Page A Body Check, Paint, and Interior Liners Procedures covered in this section: Assemble body apart from airframe and check overall fit; remove tail boom; fit and install eyebrow

More information

JK Crusher Corners. *Includes ONE of the Hardware Kits (not both)

JK Crusher Corners. *Includes ONE of the Hardware Kits (not both) INSTALLATION INSTRUCTIONS INST-18-05-020_A JK Crusher Corners IMPORTANT: Thank you for purchasing this Poison Spyder product. Please read through this entire document before proceeding with installation.

More information

69-70 Floor Pan Fixes

69-70 Floor Pan Fixes Approx Time Needed For Completion: Approx 20 hrs Equipment Needed: - Work stand or table for initial cutting, welding and working - Cooper scraps for backing during welding (prevents blow through when

More information

Jeep. Flat Style Fender Flares Front Pair. Included in Hardware Kit:

Jeep. Flat Style Fender Flares Front Pair. Included in Hardware Kit: Jeep Flat Style Fender Flares Front Pair STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure

More information

67-72 GM SHORT FLEETSIDE STEEL FLOOR TO WOOD FLOOR CONVERSION PART LIST: REQUIRED FOR CONVERSION DESCRIPTION

67-72 GM SHORT FLEETSIDE STEEL FLOOR TO WOOD FLOOR CONVERSION PART LIST: REQUIRED FOR CONVERSION DESCRIPTION JAZ:instructions\instruct\67-72conv.pm6 pg 1 67-72 GM SHORT FLEETSIDE STEEL FLOOR TO WOOD FLOOR CONVERSION PART LIST: REQUIRED FOR CONVERSION QTY DESCRIPTION 1 Set Bed Strips 1 Set Bed Wood 1 Each Bed

More information

SAFETY. Read and understand all safety precautions and instructions before installing this product.

SAFETY. Read and understand all safety precautions and instructions before installing this product. SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions

More information

Interior CHAPTER 21. Phantom Roadster Instruction Manual 273

Interior CHAPTER 21. Phantom Roadster Instruction Manual 273 CHAPTER 21 Interior When you get to this chapter you are now starting on the finish that will make your car one that will be complete your hard work. This chapter will cover the installation of the door

More information

Chevy Pickup / Suburban / Blazer Set Part # Rev B 5-04

Chevy Pickup / Suburban / Blazer Set Part # Rev B 5-04 Chevy Pickup 81-91 / Suburban / Blazer Set Part # 40019 Rev B 5-04 Step 1: Prior to Installation: A) Fit: Verify the fit of the flares to vehicle. (Some filing, sanding, or cutting may be necessary to

More information

Written By Phil (T90) for Team MudRhino

Written By Phil (T90) for Team MudRhino Rock Sliders Written By Phil (T90) for Team MudRhino WWW.MUDRHINO.COM.AU The most vulnerable cosmetic part of any vehicle while off-roading is the door sills (rocker panels), located just under the doors.

More information

Installation for Full Size Polaris Ranger Crew Doors

Installation for Full Size Polaris Ranger Crew Doors Installation for Full Size Polaris Ranger Crew Doors Order of Installation: Heater Doors Wiper on to Windshield Windshield Top & Back Panel Note: Most of the steps in these instructions need to be repeated

More information

BMW X5 OEM RUNNING BOARD PART#SBBW

BMW X5 OEM RUNNING BOARD PART#SBBW INSTALLATION INSTRUCTIONS 2014-2016 BMW X5 OEM RUNNING BOARD PART#SBBW-146-74 QTY HARDWARE 1 Driver Side OEM Running Board 1 Passenger Side OEM Running Board 8 Rivet Pin 1 Page Step 1: Verify all parts

More information

Toyota FJ Cruiser 2006-Up Set Part # Revision A

Toyota FJ Cruiser 2006-Up Set Part # Revision A Toyota FJ Cruiser 2006-Up Set Part # 31924 Revision A 03-31-08 Step 1: Prior to Installation: A) Fit: Verify the fit of the flares to vehicle. (Some filing, sanding, or cutting may be necessary to ensure

More information

Toyota Tacoma Extended Cab/Standard Cab Set Part # Rev

Toyota Tacoma Extended Cab/Standard Cab Set Part # Rev Toyota Tacoma Extended Cab/Standard Cab Set Part # 31919 Rev-7 06-23-10 Step 1: Prior to Installation: A) Bushwacker only approves installing the flares according to these written instructions with the

More information

Elite Series Fender Flares

Elite Series Fender Flares Page 1 of 8 Installation Instructions I - Sheet Number I606RPG Rev.B Important Safety Information Tools Required Contents Elite Series Fender Flares Preparation Before Painting / Installation NOTE Actual

More information

TUBULAR FRONT END KIT INSTALLATION INSTRUCTIONS MUSTANG

TUBULAR FRONT END KIT INSTALLATION INSTRUCTIONS MUSTANG TUBULAR FRONT END KIT INSTALLATION INSTRUCTIONS 1979 2004 MUSTANG Pre-Installation Notes & Recommendations: Before disassembly, remove anything within the engine bay that can be removed; this will give

More information

Ford Super Duty 4x4 CB Antenna Installation 2004 F250 4x4 XLT Sport Back to 2004 F250 Main Page

Ford Super Duty 4x4 CB Antenna Installation 2004 F250 4x4 XLT Sport Back to 2004 F250 Main Page Ford Super Duty 4x4 CB Antenna Installation 2004 F250 4x4 XLT Sport Back to 2004 F250 Main Page I wanted to install a CB in my truck but I didn't particularly like any of the typical antenna installation

More information

CUT OUT FLARES INSTALLATION INSTRUCTIONS FOR 20017, 20018, F100-F150 F250-F350 P.U. & BRONCO CUT OUTS

CUT OUT FLARES INSTALLATION INSTRUCTIONS FOR 20017, 20018, F100-F150 F250-F350 P.U. & BRONCO CUT OUTS 20017 04/22/03 REV-A CUT OUT FLARES INSTALLATION INSTRUCTIONS FOR 20017, 20018, F100-F150 F250-F350 P.U. & BRONCO CUT OUTS Tools Required for Installation: (A) 3/16 Drill Bit (B) Pop-Rivet Gun (C) Air

More information

BN6-BN7 Hardtop Restoration

BN6-BN7 Hardtop Restoration BN6-BN7 Hardtop Restoration By John Homonek Here is how I restored mine: I disassembled the hardtop - but did this with a camera in hand. Take many pictures and take way more pictures than you think you

More information

Jeep Cherokee Door XJ Set Part # Revision J

Jeep Cherokee Door XJ Set Part # Revision J Jeep Cherokee 84-96 4 Door XJ Set Part # 10911 Revision J 6-5-06 Step 1: Prior to Installation: A) Fit: Verify the fit of the flares to vehicle. (Some filing, sanding, or cutting may be necessary to ensure

More information

How to use a Touch Up Bottle & Brush

How to use a Touch Up Bottle & Brush How to use a Touch Up Bottle & Brush Tech Tips General Definitions Base Color (Basecoat): A color coat requiring a clear coat. Base Color provides color and appearance, while the clear coat provides gloss

More information

RangerWare Fiberglass Door System Installation Instructions P/N

RangerWare Fiberglass Door System Installation Instructions P/N Page 1 of 9 RangerWare Fiberglass Door System Installation Instructions P/N 2878016 ORDER OF INSTALLATION Note: To assure proper order, read all Accessory Installation Instructions before beginning. 1.

More information

Jeep Cherokee 4-Door XJ Set Part # Rev

Jeep Cherokee 4-Door XJ Set Part # Rev Jeep Cherokee 4-Door XJ Set Part # 10911 Rev-14 04-05-10 Step 1: Prior to Installation: A) Bushwacker only approves installing the flares according to these written instructions with the hardware provided.

More information

6625 WEST WILSHIRE BLVD. OKLAHOMA CITY, OK (405) FAX (405)

6625 WEST WILSHIRE BLVD. OKLAHOMA CITY, OK (405) FAX (405) INSTALLATION INSTRUCTIONS FOR BEDSIDE INNER REPAIR PANELS 67-72 GM FLEETSIDES This instruction illustrates the removal and replacement of the often rusted and damaged lower inner flanges on the 1967-1972

More information

Toyota Cut-Out TM Fender Flares Set of 4

Toyota Cut-Out TM Fender Flares Set of 4 Toyota Cut-Out TM Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure

More information

Balustrade Systems / Installation Instructions

Balustrade Systems / Installation Instructions A. PARTS AND SUPPLIES NEEDED FOR INSTALLATION Hardware included for each 10 section of rail: 2 3 x 1-1/2 L-brackets 4 1-3/4 x 3/16 Blue hex-head screws for anchoring the L-brackets to the newel cap, column

More information

1/4 Rubber Spacer, 26 pcs. M5-.8 Machine Screw, 26 pcs 13. Female Wire Connector, 4 pcs

1/4 Rubber Spacer, 26 pcs. M5-.8 Machine Screw, 26 pcs 13. Female Wire Connector, 4 pcs 97-06 Jeep Wrangler TJ Set Part #10920-07 Rev-3 12-15-08 A) B) C) D) E) F) G) STEP 1 - PRIOR TO INSTALLATION Bushwacker only approves installing the fl ares according to these written instructions with

More information

I m going to say that Rob coerced me to take part in the club Shell 4000 theme build. He promised me an engine free Tamiya kit. This is what I got

I m going to say that Rob coerced me to take part in the club Shell 4000 theme build. He promised me an engine free Tamiya kit. This is what I got I m going to say that Rob coerced me to take part in the club Shell 4000 theme build. He promised me an engine free Tamiya kit. This is what I got instead. Looks like it s an older Fujimi kit and it does

More information

gently pry up all your door switches.. disconnect them.. same with the mirror control on the drivers side..

gently pry up all your door switches.. disconnect them.. same with the mirror control on the drivers side.. How To Recover Door Panels By: Crispy SUPPLY/TOOL LIST NEEDED Dremel with drill cutter attachment (or drill with drill bit) contact cement 1/2 inch self tapping screws Carpet/Headliner spray on glue Phillips

More information

Refurbishing Your Lincoln Mark VII Dew Wipes

Refurbishing Your Lincoln Mark VII Dew Wipes By Rick One_Way Eckenrode Refurbishing Your Lincoln Mark VII Dew Wipes A common flaw among Lincoln Mark VII s can be found at the top of both doors. The dew wipes (rubber weatherstrip that rests against

More information

INSTALLATION INSTRUCTIONS Stillen Front Fascia P/N: KB NISSAN ALTIMA SEDAN

INSTALLATION INSTRUCTIONS Stillen Front Fascia P/N: KB NISSAN ALTIMA SEDAN Materials supplied: 1. (2pc) Front Fascia 2. 2 Double-sided Tape 3. (8) ¼-20 x ¾ Bolts 4. (10) ¼-20 Nuts 5. (20) Washers 6. (2) ¼-20 x 1 Bolts 7. (1) Mesh Grill Insert, Upper 8. (10) No.6 Screws 9. (10)

More information

Written by Administrator Monday, 29 November :54 - Last Updated Thursday, 02 December :00

Written by Administrator Monday, 29 November :54 - Last Updated Thursday, 02 December :00 Security Screen Doors One of the most important decisions you will make in acquiring your door will the selection of the finish for your door. Two similar doors will seem very different depending on the

More information

INSTALLATION INSTRUCTIONS 3"/4 BENT END SIDEBARS FORD F-150 SUPERCREW PART # DZ /DZ

INSTALLATION INSTRUCTIONS 3/4 BENT END SIDEBARS FORD F-150 SUPERCREW PART # DZ /DZ INSTALLATION INSTRUCTIONS 09-12 FORD F-150 SUPERCREW PART # DZ 372697/DZ 372699 PARTS LIST: 1 Driver/Left Sidebar 4 1/2 Lock Washers 1 Sidebar 4 12mm x 32mm OD x 3mm Flat Washers 1 Driver/Left Mounting

More information

GENERATION II FENDERS

GENERATION II FENDERS INSTALLATION INSTRUCTIONS FOR 97-06 JEEP TJ GENERATION II FENDERS *Thank you for your purchase of our Generation II Fenders! We hope that you will love the new look and function of your Jeep with the addition

More information

MGB V8 Roadster restoration project Report 72

MGB V8 Roadster restoration project Report 72 8th September 2016. I thought it would be useful to try this product and report how I got on with it. Reading the instructions it all seemed quite easy. You push the tube down into the box section. Press

More information

Congratulations on your purchase of our new reproduced 1969 Mercury Cougar Stainless Steel Rocker Moldings

Congratulations on your purchase of our new reproduced 1969 Mercury Cougar Stainless Steel Rocker Moldings Congratulations on your purchase of our new reproduced 1969 Mercury Cougar Stainless Steel Rocker Moldings Before starting installation, we recommend that you read these instructions a couple of times

More information

Jeep. Flat Style Fender Flares Set of 4. Included in Hardware Kit: STEP 1 PRIOR TO INSTALLATION. Set Part # Rev-3 1/11/2016

Jeep. Flat Style Fender Flares Set of 4. Included in Hardware Kit: STEP 1 PRIOR TO INSTALLATION. Set Part # Rev-3 1/11/2016 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions

More information

DIY RUSTIC HALL TREE

DIY RUSTIC HALL TREE DIY RUSTIC HALL TREE *Before beginning this project, please read through all of the plans as well as the blog post associated with this project. Always use safety precautions whenever using power tools

More information

FENDER FLARE INSTALLATION

FENDER FLARE INSTALLATION TG-FF8T4178: Fit 2014-UP Toyota Tundra PRIOR TO INSTALLATION IMPORTANT Tyger only approves the installation according to our instructions with the hardware provided. WARNING Failure to complete the installation

More information

MM Strut Tower Brace, GT (MMSTB-5.1)

MM Strut Tower Brace, GT (MMSTB-5.1) 3430 Sacramento Dr., Unit D San Luis Obispo, CA 93401 Telephone: 805/544-8748 Fax: 805/544-8645 www.maximummotorsports.com MM Strut Tower Brace, 1996-97 GT (MMSTB-5.1) MMSTB-5.1 is for 1996-97 GT s with

More information

INSTALLATION INSTRUCTIONS KK-K9-C12-K CHEVY IMPALA

INSTALLATION INSTRUCTIONS KK-K9-C12-K CHEVY IMPALA INSTALLATION INSTRUCTIONS KK-K9-C12-K 2000-2005 CHEVY IMPALA READ ALL INSTRUCTIONS PRIOR TO INSTALLATION TOOLS REQUIRED: Power Drill Drill bits1/4 and 5/32 7/l6 wrench and socket 15,18 and\or 19mm socket

More information

BPF Toyota Tundra Mesh Installation Guide

BPF Toyota Tundra Mesh Installation Guide BPF 2007-2009 Toyota Tundra Mesh Installation Guide www.bpfabricating.com Tools Required Philips Screw Driver Flat Head Screw Driver Dremel or Rotary Tool Hand Saw or Multi Max Adjustable Square Tape Measure

More information

Renault Scenic Grand Scenic 2 II Drivers Side Front Windscreen Wiper Arm Repair Kit Bearings Installation Instruction Guide

Renault Scenic Grand Scenic 2 II Drivers Side Front Windscreen Wiper Arm Repair Kit Bearings Installation Instruction Guide Renault Scenic Grand Scenic 2 II Drivers Side Front Windscreen Wiper Arm Repair Kit Bearings Installation Instruction Guide by x8rltd on July 24, 2015 Intro: Renault Scenic Grand Scenic 2 II Drivers Side

More information

STYLE BAR & TONNEAU COVER INSTALLATION

STYLE BAR & TONNEAU COVER INSTALLATION STYLE BAR & TONNEAU COVER INSTALLATION INSTALLATION MANUAL: 2005 to '09 Mustang P/N: 10-8002-C12071B Saleen Performance, Inc. 1225 East Maple Rd., MI 48083 800-888-8945 www.saleen.com 1 IF YOU ARE NOT

More information

Flat Style Fender Flares Rear Pair. Jeep. Included in Hardware Kit:

Flat Style Fender Flares Rear Pair. Jeep. Included in Hardware Kit: Jeep Flat Style Fender Flares Rear Pair STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure

More information

5/16 Hex Head Bolt, 16 pcs. Plastic Push Retainer, 6 pcs. Alcohol Wipe, 2 pcs. Side Refl ex Reflector, 2 pcs

5/16 Hex Head Bolt, 16 pcs. Plastic Push Retainer, 6 pcs. Alcohol Wipe, 2 pcs. Side Refl ex Reflector, 2 pcs STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions

More information

Flat Style Fender Flares Front Pair. Jeep. Included in Hardware Kit:

Flat Style Fender Flares Front Pair. Jeep. Included in Hardware Kit: Jeep Flat Style Fender Flares Front Pair STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure

More information

Rubber Grommet, 36 pcs. 3/4 Screw, 10 pcs. Nut, 10 pcs

Rubber Grommet, 36 pcs. 3/4 Screw, 10 pcs. Nut, 10 pcs Jeep Cherokee ZJ Set Part #10916-07 Rev-2 03-11-10 THESE INSTRUCTIONS INVOLVE CUTTING THE FENDERS OF THE VEHICLE. IT IS IMPORTANT TO READ ALL INSTRUCTIONS PRIOR TO THE CUTTING AND INSTALLATION OF THESE

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS NOTE: Bolts should remain hand tight until all bolts are installed. STEP 1 Installing the door base (both sides). 1. Locate the outer, roll cage, mounting bolt (passenger side is shown in the illustration).

More information

FENDER FLARE. KIT CONTAINS Qty Part Description Qty Part Description

FENDER FLARE. KIT CONTAINS Qty Part Description Qty Part Description ` FENDER FLARE Part No: FFC3002S TO AVOID BEING SCRATCHED, PLEASE PROTECT THE SURFACE OF THE FENDER FLARE CAREFULLY. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. 60-180 min Cutting Not Required

More information

MM Strut Tower Brace, Cobra (MMSTB-7)

MM Strut Tower Brace, Cobra (MMSTB-7) The MM strut Tower Brace attaches to each strut tower and to the firewall. 3430 Sacramento Dr., Unit D San Luis Obispo, CA 93401 Telephone: 805/544-8748 Fax: 805/544-8645 www.maximummotorsports.com MM

More information

FENDER FLARE INSTALLATION

FENDER FLARE INSTALLATION : 2011-2014 Ram 2500/3500 Fleetside 76.3 inch and 98.3 inch Bed. Tools Required 1. #2 Phillips Driver 2. Socket Wrench 3. 8mm Socket 4. 1/2 Wrench 5. Utility Knife 6. Awl or Similar Pointed Tool PRIOR

More information

ADULT. Adirondack / Muskoka Chair Plans

ADULT. Adirondack / Muskoka Chair Plans ADULT Adirondack / Muskoka Chair Plans Materials List 3/4" x 9 1/2" (1.9cm x 24.1cm) redwood, cedar or pine boards. Six, 8' (2.44m) boards should make one chair depending on knots and layout. You can also

More information

JK Brawler Rockers. *Includes ONE of the Hardware Kits (not both)

JK Brawler Rockers. *Includes ONE of the Hardware Kits (not both) INSTALLATION INSTRUCTIONS INST-17-08-200_A JK Brawler Rockers IMPORTANT: Thank you for purchasing this Poison Spyder product. Please read through this entire document before proceeding with installation.

More information

Polishing Stainless Steel and Aluminum

Polishing Stainless Steel and Aluminum Polishing Stainless Steel and Aluminum Richard Widman One of the advantages of Corvairs and many cars of the 50 s and 60 s is that the shiny trim is made of Stainless Steel and Aluminum rather than Chrome

More information

Rev TOOLS & MATERIALS REQUIRED QTY 3D PART NO. DESCRIPTION

Rev TOOLS & MATERIALS REQUIRED QTY 3D PART NO. DESCRIPTION Rev. 04-11 QTY 3D PART NO. DESCRIPTION 1 691800 FRONT AIR DAM 1 691802 RIGHT SIDE SKIRT 1 691801 LEFT SIDE SKIRT 1 691804 REAR LOWER SKIRT RIGHT SIDE 1 691803 REAR LOWER SKIRT LEFT SIDE 4 3M 94 3M ADHESION

More information

Included in Hardware Kit: Jeep Pocket Style Fender Flare Set of 4. Set Part # Rev-0 3/15/2013 TOOLS FOR EASY INSTALLATION:

Included in Hardware Kit: Jeep Pocket Style Fender Flare Set of 4. Set Part # Rev-0 3/15/2013 TOOLS FOR EASY INSTALLATION: STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions

More information

FENDER FLARE INSTALLATION

FENDER FLARE INSTALLATION : 2009 - UP Ram 1500 Fleetside. (Exclude R/T Models) Tools Required 1. #2 Phillips Driver 2. Socket Wrench 3. 8mm Socket 4. 1/2 Wrench 5. Utility Knife PRIOR TO INSTALLATION Hardware Kit Included 5/16

More information

CLUB-SPORT ROLL BAR: Volkswagen Mk4 Golf

CLUB-SPORT ROLL BAR: Volkswagen Mk4 Golf HPA Motorsports Inc. 604-888-7274 www.hpamotorsport.com CLUB-SPORT ROLL BAR: Volkswagen Mk4 Golf Congratulations on the purchase of your Club-Sport Roll Bar from HPA Motorsports! The engineering elements

More information

GENERAL REPAIR INSTRUCTIONS Work Precautions

GENERAL REPAIR INSTRUCTIONS Work Precautions IN-10 GENERAL REPAIR INSTRUCTIONS Work Precautions SAFETY Never stand in direct line with the chain when using a puller on the body or frame, and be sure to attach a safety cable. VEHICLE PROTECTION When

More information

2013 SKILLS CANADA NATIONAL COMPETITION

2013 SKILLS CANADA NATIONAL COMPETITION 2013 SKILLS CANADA NATIONAL COMPETITION CAR PAINTING 36 PROJECT INSTRUCTION SECONDARY Car Painting Total Time allocated: 12 hours FENDER PROJECT You will prime and paint a fender, as if it is a used OEM

More information

Cowper From Steve Wolverton on the T&TTT forum, Feb 2005 For Reference Only Do not use to build a trailer. Check on Teardrop and Tiny Travel Trailers

Cowper From Steve Wolverton on the T&TTT forum, Feb 2005 For Reference Only Do not use to build a trailer. Check on Teardrop and Tiny Travel Trailers Cowper From Steve Wolverton on the T&TTT forum, Feb 2005 For Reference Only Do not use to build a trailer. Check on Teardrop and Tiny Travel Trailers for up to date building information; http://www.mikenchell.com/forums

More information

Flat Style Fender Flares Front Pair. Jeep. Included in Hardware Kit:

Flat Style Fender Flares Front Pair. Jeep. Included in Hardware Kit: Jeep Flat Style Fender Flares Front Pair STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure

More information

Ford Ranger / Bronco II Set Part # Rev B 5-04

Ford Ranger / Bronco II Set Part # Rev B 5-04 Ford Ranger / Bronco II Set Part # 21008 Rev B 5-04 Step 1: Prior to Installation: A) Fit: Verify the fit of the flares to vehicle. (Some filing, sanding, or cutting may be necessary to ensure proper fit).

More information

Tape Measure Metal Clippers Screw Bit Set With Extensions

Tape Measure Metal Clippers Screw Bit Set With Extensions IMPORTANT: Read through instructions thoroughly before beginning to replace any damaged material. Minor damage can be fixed with a fiberglass repair kit and color matched paint. Tools Required Tape Measure

More information

FENDER FLARE. KIT CONTAINS Qty Part Description Qty Part Description TOOLS REQUIRED

FENDER FLARE. KIT CONTAINS Qty Part Description Qty Part Description TOOLS REQUIRED ` FENDER FLARE Part No: FFD3001S TO AVOID BEING SCRATCHED, PLEASE PROTECT THE SURFACE OF THE FENDER FLARE CAREFULLY. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. 60-180 min Cutting Not Required

More information

Installation Instructions

Installation Instructions 86-95 Suzuki Samurai LROR Sport Cage Front (SKU# SRC-SCF) Installation Instructions Front and Rear Cage Combined CAUTION: Safety glasses should be worn at all times when working with vehicles and related

More information

INSTALLATION INSTRUCTIONS FOR & Chevy CUT OUT FLARE

INSTALLATION INSTRUCTIONS FOR & Chevy CUT OUT FLARE 40009 7/10/03 REV-A INSTALLATION INSTRUCTIONS FOR 40009 & 40010 Chevy CUT OUT FLARE TOOLS REQUIRED FOR INSTALLATION: Drill Motor Pop Rivet Gun Flat File Hair Dryer or Heat Gun Sawzall Jack and Jack Stands

More information

Blue Bird Body Number. School or Company Name. Shipping Address. City, State, Zip. Signature. Print Name and Telephone Number

Blue Bird Body Number. School or Company Name. Shipping Address. City, State, Zip. Signature. Print Name and Telephone Number Blue Bird Body Number Recall R14XC Inspection Sheet Rear Wheelhouse to Body Gusset Panel Joint Write "Pass" if joint passes inspection. Write "Fail" if joint does not pass inspection. If outside inspection

More information

RLZ-02 - Rear Cross Bar, Ford Transit Connect.

RLZ-02 - Rear Cross Bar, Ford Transit Connect. Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the roof racks are installed in the correct locations. Check the contents

More information

Set Part # Rev

Set Part # Rev Set Part # 21007 Rev-3 06-06-11 Step 1: Prior to Installation: A) Bushwacker only approves installing the flares according to these written instructions with the hardware provided. WARNING: Failure to

More information

Rough Country JK Modular Winch Mount Bumper With Light End Caps

Rough Country JK Modular Winch Mount Bumper With Light End Caps Rough Country JK Modular Winch Mount Bumper With Light End Caps Note: These instructions involve cutting parts of your vehicle. Please read all instructions prior to starting. Note: This installation also

More information

VIEWPOINT ALUMINUM RUNNING BOARD TOYOTA RAV4

VIEWPOINT ALUMINUM RUNNING BOARD TOYOTA RAV4 PARTS LIST: VIEWPOINT ALUMINUM RUNNING BOARD 1 Driver/Left Running Board 4 10-1.5mm x 50mm T-Bolt 1 Passenger/Right Running Board 12 10mm Plastic Retainers 1 Driver/Left Bracket 2 10-1.50mm x 40mm Hex

More information

Included in Hardware Kit 2. FLAT STYLE FENDER FLARE. Jeep Wrangler YJ. Set Part # Rev STEP 1 PRIOR TO INSTALLATION

Included in Hardware Kit 2. FLAT STYLE FENDER FLARE. Jeep Wrangler YJ. Set Part # Rev STEP 1 PRIOR TO INSTALLATION Jeep Wrangler YJ Set Part #10924-07 Rev-0 05-05-11 A) B) C) D) E) STEP 1 PRIOR TO INSTALLATION Bushwacker only approves installing the fl ares according to these written instructions with the hardware

More information

Bolt-On Fender Flares Nissan Titan XD (16-ON) Important: Please read instructions entirely before installing this product.

Bolt-On Fender Flares Nissan Titan XD (16-ON) Important: Please read instructions entirely before installing this product. Important: Please read instructions entirely before installing this product. Hardware Included QTY Hardware Included QTY Bolt Kit Included Extrusion 30.5ft (Bolt-On look flare only) QTY U CLIP.6mm 6 Nuts

More information

Included in Hardware Kit 2. FLAT STYLE FENDER FLARE. Jeep Wrangler YJ Fronts. Set Part # Rev STEP 1 PRIOR TO INSTALLATION

Included in Hardware Kit 2. FLAT STYLE FENDER FLARE. Jeep Wrangler YJ Fronts. Set Part # Rev STEP 1 PRIOR TO INSTALLATION Jeep Wrangler YJ Fronts Set Part #10067-07 Rev-0 05-05-11 A) B) C) D) E) STEP 1 PRIOR TO INSTALLATION Bushwacker only approves installing the fl ares according to these written instructions with the hardware

More information

Corvette Parts, Service and Sales Orders For technical assistance us at

Corvette Parts, Service and Sales Orders For technical assistance  us at Repair and Installation Help from Corvette Parts, Service and Sales 800-588-3883 Orders For technical assistance email us at Willcoxcustomerservice@willcoxcorvette.com Diagnostic help, installing headlamp

More information

388. Wipe deck lid down with acetone, let dry and open deck lid for removal.

388. Wipe deck lid down with acetone, let dry and open deck lid for removal. Chapter 12 - Deck Lid Repair (Video Clip 12) 388. Wipe deck lid down with acetone, let dry and open deck lid for removal. 389. Remove the two screws holding the rain gutter inside the deck lid, with a

More information

Included in Hardware Kit. 09-Up Ford F150. Set Part # Rev STEP 1 - PRIOR TO INSTALLATION TOOLS FOR EASY INSTALLATION:

Included in Hardware Kit. 09-Up Ford F150. Set Part # Rev STEP 1 - PRIOR TO INSTALLATION TOOLS FOR EASY INSTALLATION: 09-Up Ford F150 Set Part #20927-02 Rev-3 5-18-09 A) B) C) D) E) F) G) STEP 1 - PRIOR TO INSTALLATION Bushwacker only approves installing the fl ares according to these written instructions with the hardware

More information

8030 Synergy Jeep JK Rear Long Arm Frame Brackets

8030 Synergy Jeep JK Rear Long Arm Frame Brackets General Notes: SYNERGY MFG. 870 INDUSTRIAL WAY, SAN LUIS OBISPO, CA (805) 242-0397 8030 Synergy Jeep JK Rear Long Arm Frame Brackets These instructions are also available on our website; www.synergymfg.com.

More information

Congratulations on purchasing the Spirit Rails Magnetic Attach that allows easy wand to pack removal and reattachment by just getting close!

Congratulations on purchasing the Spirit Rails Magnetic Attach that allows easy wand to pack removal and reattachment by just getting close! Introduction Congratulations on purchasing the Spirit Rails Magnetic Attach that allows easy wand to pack removal and reattachment by just getting close! The Spirit Rails Magnetic Attach Kit is designed

More information

Ask your DIY store or carpenter to cut the required boards to size. Instructions. 1. Cut out the opening for the bottles

Ask your DIY store or carpenter to cut the required boards to size. Instructions. 1. Cut out the opening for the bottles KITCHEN TROLLEY Next time you're whipping up some magic in the kitchen, take advantage of our willing assistant. Fixed on rollers to provide easy mobility, our kitchen trolley can be stationed wherever

More information

Plastic Push. 5/16 Hex Head Bolt, 20 pcs. Retainer, 20 pcs. Female Bullet Connector, 4 pcs. Side Refl ex Refl ector, 2 pcs

Plastic Push. 5/16 Hex Head Bolt, 20 pcs. Retainer, 20 pcs. Female Bullet Connector, 4 pcs. Side Refl ex Refl ector, 2 pcs A) B) C) D) E) F) G) STEP 1 - PRIOR TO INSTALLATION Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according

More information

Front Clip Mold. a 20 pound-or-less front clip, a savings of 38 pounds off the nose of the car.

Front Clip Mold. a 20 pound-or-less front clip, a savings of 38 pounds off the nose of the car. Front Clip Mold Those of us that have lightened our cars for racing learn quickly how much easier it is to get weight out of the back of the 928 as opposed to the front. Our front clip project last year

More information

Jeep. Cut-Out Fender Flares Set of 4. Included in Hardware Kit:

Jeep. Cut-Out Fender Flares Set of 4. Included in Hardware Kit: STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions

More information

All American Mower Blade Sharpener Mulching Blade Model Patent Pending

All American Mower Blade Sharpener Mulching Blade Model Patent Pending All American Mower Blade Sharpener Mulching Blade Model 5000 Patent Pending Revised May 3, 2017 Attaching the guide pin to your grinder: Assembly and Use Locate the guide pin (included with the sharpener)

More information

Bolt-On/Rugged Fender Flares Chevy Silverado (99-07) Please read instructions entirely before installing this product.

Bolt-On/Rugged Fender Flares Chevy Silverado (99-07) Please read instructions entirely before installing this product. Please read instructions entirely before installing this product. Hardware Included QTY Hardware Included QTY Bolt Kit Included QTY EXTRUSION 25ft FASTENERS 24 ALLEN KEY BOLT 42 ALCOHOL TOWELETTE 4 SCREWS

More information

Side and rear window, assembly overview

Side and rear window, assembly overview 64-7 Side and rear window, assembly overview 1 - Side/rear window Removing Unbroken Page 64-9 Broken Page 64-11 Installing Page 64-13 Curing time Page 64-21 Re-sealing Page 64-25 2 - PUR adhesive sealant

More information

Jeep. Flat Style Fender Flares Rear Pair. Included in Hardware Kit:

Jeep. Flat Style Fender Flares Rear Pair. Included in Hardware Kit: Jeep Flat Style Fender Flares Rear Pair STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure

More information

GRIP Mustang GT/V6 Body Kit

GRIP Mustang GT/V6 Body Kit GRIP Mustang GT/V6 Body Kit GRIP highly recommends that our kits be installed by professionals with experience installing automotive aftermarket parts and accessories. However, we do recognize that many

More information

Jeep. Cut-Out Fender Flares Set of 4. Included in Hardware Kit: Set Part # Rev-6 7/20/15 For complete fitment info visit :

Jeep. Cut-Out Fender Flares Set of 4. Included in Hardware Kit: Set Part # Rev-6 7/20/15 For complete fitment info visit : Jeep Cut-Out Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure

More information