Dino-Roar Burpie and Bib

Size: px

Start display at page:

Download "Dino-Roar Burpie and Bib"

Emmeline Kennedy
5 years ago
Views:

Dino-Roar Burpie and Bib Supp lies Needed Finished Sizes - Burpie: 7 ½" x 14 ½" Bib: 10" x 13 ½" 5 Fabric Palette Dino-Roar Flannel Fat Quarters (3 for bib; 2 for burpie) 1 pkg.

1 Dino-Roar Burpie and Bib Supp lies Needed Finished Sizes - Burpie: 7 ½" x 14 ½" Bib: 10" x 13 ½" 5 Fabric Palette Dino-Roar Flannel Fat Quarters (3 for bib; 2 for burpie) 1 pkg. Jumbo rick rack 2 ½" x 6 ½" Paper backed fusible web (for bib) ¾" Hook and loop tape (for bib) Coordinating thread 2 ½" x 6 ½" Tear-away stabilizer (optional) Clear tape Basic sewing supplies Sewing machine Iron and pressing surface B efore you begin Read all instructions before beginning project. Do not prewash fabrics. Before cutting, press with a dry iron. Use ¼" seam allowance and sew fabrics with right sides together (RST) unless otherwise noted. Print Template pieces 1 and 2 for each project. Note: When printing, check that page size is set to actual size and compare printout with template measurements noted in cutting section below. Cutting Burpie: Tape Burpie Template pieces 1 and 2 together; cut out along printed outside edge. (Template size: 8" x 15") Fabric A - Sabertooth: 1-8 ½" x 10" (Burpie Front - Center) 1-8 ½" x 15 ½" (Burpie Back) Fabric B - Green Stripe: 2-3 ½" x 8 ½" (Burpie Front Ends) Rick Rack: 2-8 ½" strips Bib: Tape Bib Template pieces 1 and 2 together; cut out along printed outside edge. (Template size: 10 ½" x 14") Fabric A - Navy Dino: 1-11" x 11" (Bib Front - top) Fabric B - Green Stripe: 1-4" x 11" (Bib Front - bottom) Fabric C - Gray Dot: 1-10 ½" x 14 ½" (Bib Back) 1-2 ½" x 6 ½" (Letters) Rick Rack: 1-11" strip Hook and loop tape: 1 - ¾" square 2015 Fabric Editions, Inc. Fabric Palette is a trademark of Fabric Editions, Inc. page 1

2 S ewing the Burpie 1. Pin a Burpie Front (Fabric B) end piece to each short edge of the Burpie Front (Fabric A) center piece RST; sew and press seams open (Dia. A). Burpie front should measure 8 ½" x 16" 3 ½" End Dia. A + 10" Center = 16" 3 ½" End + 8 ½" 8 ½" 2. Pin a rick rack strip over each seam and sew down the center to attach (Dia. B). Dia. B Rick Rack Rick Rack 3. Line up the dotted lines on the Burpie template with the center of the rick rack; trace and cut out the Burpie Front (Dia. C). 4. Trace the template on the wrong side of the Burpie Back (Fabric A) and cut out. 5. Place Front and Back RST; pin. Sew around outside edges leaving a 3" opening for turning; clip curves. 6. Turn right side out; press and hand stitch opening closed. Topstitch ¼" from edge. Dia. C page 2

3 S ewing the Bib Dia. A 1. Refer to Diagram A to pin Bib Front Top (Fabric A) and Bib Front Bottom (Fabric B) RST. Sew and press seam open (Dia. A). Sewn Bib Front should measure 11" x 14 ½". 11" + 4" 11" 2. Center and pin the rick rack over the seam. Sew down the center of rick rack (Dia. B). Dia. B 14 ½" Rick Rack 3. Position the bib template on the Bib Front with the dotted line centered over the rick rack; trace and cut out (Dia. C). 4. Trace the letters on page 4 onto the paper side of the fusible web. Follow manufacturer s directions to fuse the letters to the wrong side of Fabric C (2 ½" x 6 ½"). Cut out along traced lines and remove paper backing. 5. Refer to the photo to arrange the letters on the right side of the Bib Front above the rick rack or place as desired. Fuse and sew around letters with a zig zag or decorative stitch to secure. Optional: Follow manufacturer s directions to use tear-away stabilizer under appliqué. 6. Trace template on Bib Back (Fabric C) and cut out. 7. Place Bib Front and Back RST; pin. Sew ¼" around outside edges leaving a 3" opening for turning; clip curves and trim corners. 8. Turn right side out; press. Hand stitch opening closed. Topstitch ¼" from edge. Finishing the Bib 9. Pin loop (soft) side of hook and loop tape to the back side of the left neck tab; stitch around edges. Pin hook (rough) side to the front of the right neck tab. Check that they line up and stitch around edges. 11" Dia. C Finished Care Instructions Machine wash cold, gentle cycle. Tumble dry low or hang to dry. page 3

4 Roar! Template For Bib Burpie Template Piece 1 Line up piece 1 with piece 2 on solid line for full size burpie template 6 ½" page 4

5 6 ½" Line up piece 1 with piece 2 on solid line for full size burpie template Leave open for turning Burpie Template Piece 2 page 5

6 Bib Template Piece 1 Neck Tab Neck Tab Line up piece 1 with piece 2 on solid line for full size bib template 10 ½" page 6

7 Bib Template Piece 2 10 ½" Line up piece 1 with piece 2 on solid line for full size bib template Leave open for turning page 7

Reversible S louch Bag Finished Size: 15" x 24" (includes straps)

www.fabriceditions.com Reversible S louch Bag Finished Size: 15" x 24" (includes straps) Supp lies Needed 2 Fabric Palette Half Yards (18" x 42") - coordinating 1 ¼ yds. Lightweight fusible interfacing