Contour Measuring System CONTRACER CV-1000/2000

Transcription

1 Form Measurement Contour Measuring System CONTRACER CV-1000/2000 Bulletin No Digital, cost-effective contour measuring instruments feature excellent portability and versatility.

2 Digital analysis type tat feature excellent portability and versatility CONTRACER CV-1000/2000 Versatile combinations to suit different applications Coose te combination tat best suits your application. Optional Software CV-1000N2 FORMPAK Portability enables on-site measurement CV-1000N2 Stand: option (see P.6) CV-2000M4 Notebook PC Type Measuring range X axis 2"(50mm) Z axis 1"(25mm) Z axis resolution.016μm (0.4μm) Desktop PC Type CV-2000M4 NOTEBOOK PC CV-2000M4 DESKTOP PC CV-1000N2 NOTEBOOK PC CV-1000N2 DESKTOP PC Versatility CV-2000M4 Measuring range X axis 4"(100mm) Z axis 1.5"(40mm) Z axis resolution.02µm (0.5μm) Stand: standard accessory Z-axis Detecting Unit Linear digital scales are provided for detecting position on te X-axis. A newly developed digital circular-arc scale is used on te Z-axis. Tese offer ig resolution measurement in a wide range. Ligt emitter Circular scale Circular-scale metod Patent registered (in Japan, USA, UK) Patent pending (in Germany) Analog metod Ligt receiver Te Circular Scale Easy setup witout concern for te measurement range and magnification. Hig resolution improves measuring accuracy. Entire measuring range Same Resolution Narrow measurement range and difficult setup. Even after setup, te resolution is low. Narrow Measuring range Hig Resolution Operators are free from botersome operations suc as te measurement magnification switcing and calibration for eac magnification required for analog instruments. Wide Low 2

3 Specifications Model No. CV-1000N2 CV-2000M4 Order No A A Measuring range X axis 2" (50mm) 4"(100mm) Z axis 1" (25mm) 1.57"(40mm) X axis (138+20L)µm.5+2L/100 µm L Measurement lengt mm Accuracy ±( H )µm ±(3.5+ 4H /25)µm ±( H )µm ±.5+ 4H /25 µm Z axis H Measurement eigt (mm) from a level position (less tan ±12.5mm) H Measurement eigt (mm) from a level position (less tan ±20.0mm) Traverse linearity (wit te X axis orizontal) 138µm / 2" (3.5µm/50mm) 138µm / 4" (3.5µm/100mm) Z axis resolution 0.4µm 0.5µm Drive speed Measuring (0.2/0.5mm/s) Moving (0.2/1.0mm/s and manual) Measuring force 1 ~ 3gf (10 ~ 30mN) (in orizontal, using te standard arm) Limiting trace angle of stylus Up (dependent on surface quality) 77 Down (dependent on surface quality) 87 Direction of measurement Toward drive unit Direction of te stylus wen measuring Down X-axis operation * Motor driven / manual control knob is included Stand Option Manual column stand Base dimensions (W D H) 23.62" x 17.71"( mm) Base material Granite External dimensions (W D H) 19.27" x 5.42" x 7" ( mm) 27.07" x 17.7" x 29.1"( mm) Mass 11 lbs (5.0kg) 255 lbs (115.8kg) *Positioning, retraction, etc Dimensions CV-1000N2 CV-2000M4 (UNIT : mm) Z=0 Position X=25 Position Vertical travel range 320mm Z=0 Position X=50 Position

4 Software, FORMPAK-1000 Measurement Control Te command buttons necessary for executing and creating a measurement procedure (part program) are laid out on te measurement control screen. Any unused button or display area can be displayed or idden arbitrarily, allowing te operator to customize te screen layout for ease of use. A measurement procedure can be easily invoked by selecting it from te pull-down menu. Profile Analysis Various commands including point commands (10 kinds), line commands (6 kinds), and circle commands (6 kinds) are provided to cover te basic elements of analysis. Standard calculation commands tat combine tese elements for angle, pitc or distance calculation are also provided. Te display can be tailored by te customization function to suit te application. For example, te calculation command can be idden to simplify te measurement environment and allow te user to focus just on te commands actually used in te application. Calculation results are output as text (in csv or/and txt format). Te geometrical measurement data can eiter be output as point-series data into a text file or CAD file (in DXF or IGES format) or copied onto te clipboard. It is also possible to use some commercial documentation software and statistical processing software to sare te data on a PC tat is not installed wit te Mitutoyooriginal analysis software or were reverse engineering wit CAD is intended. Wit te useful Automatic Circle/Line Application command it is possible to automatically calculate all circles and lines tat are included in te data witout pressing te command button many times over. Te Outlier Removal Function is very useful, for example, for automatically removing flaws from te data and setting te calculation range for sections were te boundary between a circle and a line cannot be easily identified. 4

5 Design Data Generation Profile Tolerance Zone Measurement Desired nominal profile data can be extracted from a CAD file (DXF- or IGES-formatted). Also, measurement results can be converted into profile data. Measurement data for parts can be stored before use/test and are ten available for cecking te extent of wear after te part as been in service for some time. Furtermore, creation of nominal profile data of asperical lens from text files in CSV format, and entry of rotational symmetric polynominal aspere formula (up to 20t order ) are possible. Measurement data can be compared directly wit te corresponding design data. A Best-Fit function is used tat translates bot te design data and measurement data to teir optimal coordinates. Te resulting profile tolerance zone measurements can be presented bot in a visual form as diagrams of geometrical contour data sowing te amount of error at eac coordinate, and as a text-file formatted output tat, for example, can be used for feedback to an NC macine tool for error correction purposes. Report Creation Data Composition Te operator can freely assemble and lay out measurement results, setups, graps, comments, etc., to form a measurement result report. Bitmap files can also be pasted in and tus, for example, workpiece potos and company logos can be easily included in a report. It is also possible to save a particular layout and reuse it for repeat measurements. Completed reports can be stored or printed as required. Selected sections of a workpiece contour can be measured and analyzed separately before combining tem to form te complete contour by overlapping corresponding elements (lines or points) in te data. Tis functionality is very useful for analyzing workpiece sapes tat cannot be measured at a single setting of te macine

6 Optional Accessories Manual column stand for CV-1000N2 Floor stand and tables Suitable for desktop use in inspection rooms and suc. No Except measuring unit CV-1000N2 Vertical adjustment range20mm Dimensions W D H mm Mass 110 kg Dimensions Unit mm Vibration-damping stand Order No Vibration damping Preumatic type w/ system self-leveling External size 25 x 20 x x 508 x 51mm Max. loading mass 175 lbs (80 kg) 740 Vibration Isolated frame wit work surface Order No. Dimensions Load Capacity x 48 x 30" 1000 lbs Manual column stand (OPTION) System cofiguration including optional accessories Leveling table (Wit analog eads) (mm) (inc) Leveling table (Wit digital eads) (mm) (inc) Leveling table Calibration stand 12AAG175 V-block Precision vise Cross-travel table (mm) (inc) Cross-travel table (mm) (inc) Rotary vise Center supports Center support riser Swivel center support Holder wit clamp V-block wit clamp V-block wit clamp

7 Arms and Stylus Optional Arms and Stylus Arms Straigt arm Eccentric arm For small ole Styli One-sided cut stylus mm Cone stylus Knife-edge stylus For small-ole stylus SP-11/ For small-ole stylus SP-13/33 8 H H H Intersecting cut stylus 20 Cone stylus 0 1mm 15 Ball stylus For small-ole stylus SP-12/ Select an arm and stylus tat matc te type of measurement you require. Type of arm Arm No. Parts No. Adaptation stylus No. H mm AB SPH-51,52,53,54,55,56,57 6 AB SPH-61,62,63,64,65,66,67 12 Straigt arm AB SPH-71,72,73,74,75,76,77,79 20 AB SPH-81,82,83,84,85,86,87 30 AB SPH-91,92,93,94,95,96,97 42 AB SPH-51,52,53,54,55,56,57 6 AB SPH-61,62,63,64,65,66,67 12 Eccentric arm AB SPH-71,72,73,74,75,76,77,79 20 AB SPH-81,82,83,84,85,86,87 30 AB SPH-91,92,93,94,95,96,97 42 SP-11, For small ole AB SP-12,32 1 SP-13, Standard accessory Type of stylus Stylus No. Parts No. Adaptation arm No. mm SPH AB SPH AB One-sided cut stylus SPH AB SPH AB SPH AB SPH AB SPH AB Intersecting cut stylus SPH AB SPH AB SPH AB SPH-57 12AAE865 AB Cone stylus SPH-67 12AAE866 AB Tip angle 20 SPH-77 12AAE867 AB Carbide SPH-87 12AAE868 AB SPH-97 12AAE869 AB SPH AB Cone stylus SPH AB Tip angle 30 SPH AB Sappire SPH AB SPH AB Cone stylus Tip angle 50 diamond SPH AB SPH-56 12AAA566 AB Cone stylus SPH-66 12AAA567 AB Tip angle 30 SPH-76 12AAA568 AB Carbide SPH-86 12AAA569 AB SPH-96 12AAA570 AB SPH AB Knife-edge stylus SPH AB SPH AB SPH AB SPH AB SPH AB SPH AB Ball stylus SPH AB SPH AB For small-ole stylus One-sided cut For small-ole stylus Cone Standard accessory SPH AB SP AB-11 2 SP AB-11 4 SP AB SP-31 12AAE873 AB-11 2 SP-32 12AAE874 AB-11 4 SP-33 12AAE875 AB

8 One Number to Serve You Better MITUTOYO ( ) Note: All information regarding our products, and in particular te illustrations, drawings, dimensional and performance data contained in tis printed matter as well as oter tecnical data are to be regarded as approximate average values. We terefore reserve te rigt to make canges to te corresponding designs. Te stated standards, similar tecnical regulations, descriptions and illustrations of te products were valid at te time of printing. In addition, te latest applicable version of our General Trading Conditions will apply. Only quotations submitted by ourselves may be regarded as definitive. Mitutoyo products are subject to US Export Administration Regulations (EAR). Re-export or relocation of Mitutoyo products may require prior approval by an appropriate governing autority. Trademarks and Registrations Designations used by companies to distinguis teir products are often claimed as trademarks. In all instances were Mitutoyo America Corporation is aware of a claim, te product names appear in initial capital or all capital letters. Te appropriate companies sould be contacted for more complete trademark and registration information. We reserve te rigt to cange specifications and prices witout notice. Aurora, Illinois (Corporate Headquarters) Westford, Massacusetts Huntersville, Nort Carolina Mason, Oio Plymout, Micigan City of Industry, California 2009 Mitutoyo America Corporation, Aurora IL Printed in USA October 2009