General Information. Profile Overview. Profile Combinations. Material. Processing. Glazing/Assembly. Annex

Transcription

1 General Information 1 Profile Overview 2 Profile Combinations 3 Material 4 Processing 5 Glazing/Assembly 6 Annex 7

2 1 General Information General Notes System Description Technical Specifications Profile Sets Type Overview Maximum Sizes Wind Load List of Suppliers

3 General Notes 1 General Notes Dear Customer, This manual contains important information about the VEKASLIDE lift/slide door. Structur of the manual The Chapter "General Information will give you a brief overwiev of the data. The Profile overview chapter proviedes a detailed description of the articles. You will find information on profile cross-sections in the Profile combinations chapter. The Chapter "Material contains article and kit lists as well as the reduction measure. The section "Application, Use describes working steps necessary for the construction of a lift/slide door. Important guidelines for further processing are presented in the Assembly/ Glazing chapter. Test reports and material characteristic are shown in the Annex. Each chapter is divided into sub-chapters. A table of contents on the first page of each chapter will give you a quick overview of the relevant chapter. Margin notes show which chapter you are reading. Important symbols Some information is presented in a text frame using a symbol.! Please note! Please read carefully the text passages marked this way. These passages contain important information you should always pay attention to in order to avoid serious errors. i Information Text passages that are specially marked this way contain useful information or notes. Abbreviations used: EW= Element width EH = Element height SW = Sash width GM = Glass size HST = Lift/Slide door SS = Sliding sash FS = Fixed sash U w value = Heat transition coefficient RC = Resistance class Exclusion of warranty Inasmuch as this documentation describes Technical solutions using products from other suppliers, they are used for demonstration purposes only and may offer different possibilities. Please consult the supplier as to whether the products are fit for the purpose and suitable for a specific installation. We assume no liability to the products concerned. This documentation refers in particular to the VEKASLIDE lift/slide door VEKASLIDE. Please consult the revised version of our VEKA Window Systems Fabrication Manual (020) for general information on window installation and the Profile Overview chapter (104). Please note that the product range and technical specifications are subject to change without prior notice. Documentation has been carefully prepared and examined. However, it may contain errors and is nevertheless not possible to exclude errors. If you identify any errors, please notify our editorial team. Special cases/exceptions Please note that subsequent foil application on elements with white profiles, their, painting, facing or similar is only permitted if the maximum sizes and the working steps for the relevant coloured design have been used as a basis. Scales Profiles and accessories contained in the article list or similar are usually not shown in their actual size. Figures drawn to scale are marked correspondingly. Example Some matters described in this documentation do not explicitly refer to the special lift/slide door and provide general information that can be applied to different profile systems. 1.2 General information

4 System description Technical Specifications Technical specifications System designation: VEKASLIDE Opening function: Lift/slide door Building depth, frame: 170 mm/7 chambers Building depth, sash: 70 mm/5 chambers Maximum pane thickness: 42 mm 1 Test values Air permeability: Class 4 Wind load resistance: up to B4* Driving rain resistance: 7a Burglar resistance: up to RC 2 * depending on the sash height and width The standards upon which the test values are based are shown in the Annex. Overview Model: white coloured Systems: A, D K, C, F A, D K, C, F Maximum element width: 6.00 m 6.50 m 5.00 m 6.50 m Maximum element height: 2.70 m 2.40 m Maximum sash width: 3.00 m 2.50 m Maximum sash surface area: 6.50 m²* 5.50 m²* Max. glass weight (per sash) 250 kg 250 kg * depending on B1-B4 classification General information 1.3

5 System description 1 Profile sets Width Frame sets, System A, white Height Size 30/ Size 30/ Size 35/ Size 35/ Size 40/ Size 40/ Size 50/ Size 50/ Width Sash sets, System A, white Height Size 30/ Size 30/ Size 35/ Size 35/ Size 40/ Size 40/ Size 50/ Size 50/ i Information When installing either foiled lift/slide doors or lift/slide doors with a width exceeding 5 m, no specific kits are offered. If you wish to order the required materials, please contact our sales department. Due to different glass thickness, the kits do not contain any glazing beads. An overview of glazing beads is contained in the Glazing/Assembly chapter.! Please note! For the construction of a complete white lift/slide door you require the following sets: Frame set Sash set Threshold set Fittings set Sealing set Standard Optional (not included in the kits) Alu drip mould, standard Insulation wedges, frame and threshold Glazing beads 1.4 General information

6 System description Threshold sets, VEKA Exotherm 1.5, P Width Size 3000 Size Size Size Size Size In general, thresholds from G-U Gretsch-Unitas can be used. Width Fittings sets, System A Height Size 30/ Size 30/ Size 35/ Size 35/ Size 40/ Size 40/ Size 50/ Size 50/270 * optional gear extension at a height of 2700 mm (Standard backset 27.5, no RC 2 ) * * * * i Information All kits and sets refer to System A. For additional systems, no fixed kits are offered. If you wish to order the required materials, please contact our sales department.! Please note! For the construction of a complete white lift/slide door you require the following sets: Frame set Sash set Threshold set Fittings set Sealing set Standard Optional (not included in the kits) Alu drip mould, standard Insulation wedges, frame and threshold Glazing beads General information 1.5

7 Type overview Type overview 1! Please note! When installing movable sashes, the sash height / sash width ratio of > 2:1 must be avoided under all circumstances! Systems Plan D and F have only low requirements with regard to leak tightness! System: A System: D System: K System: K- 3 part (lift/slide door) with false mullion System: C Variant, System: C System: F 1.6 General information

8 Maximum sizes Maximum sizes! Please note! Static and structural calculation is required when installing windows of 9m 2 and above. The maximum permitted pane thickness is 42 mm. 1 The relevant element sizes are only permitted with reinforcement and are highlighted as follows:. permitted element size with reinforcement : 58 x 45.5 x 2 mm 58 Y X 45.5 Reinforcement : 58 x 45.5 x 2 mm Ix = 8.65 cm 4 ly = cm 4 General information 1.7

9 Maximum sizes 1 Permitted element sizes according to B1 classification, model in white and cream-white Element height Element width System A / D not permitted element size with a sash height to sash width ratio of > 2:1 permitted element size with reinforcement : 58 x 45.5 x 2 mm not permitted sash size, white max. 6.5 m 2, max. sash width 3.0 m Maximum sash surface area=6.5 m² Element height Element width System K System C / F Permitted element sizes according to B1 classification model in color Element height Element width System A / D not permitted element size with a sash height to sash width ratio of > 2:1 permitted element size with reinforcement : 58 x 45.5 x 2 mm not permitted sash size, coloured, max. 5.5 m², max. sash width 2.5 m Maximum sash surface area=5.5 m² Element height Element width System K System C / F General information

10 Maximum sizes Permitted element sizes according to B2 classification, versions in white and cream-white Element height Element height Element width System A / D Element width System K System C / F not permitted element size with a ratio sash height to sash width ratio of > 2:1 permitted element size with reinforcement : 58 x 45.5 x 2 mm not permitted sash size, white max. 6.0 m 2, max. sash width 3.0 m Maximum sash surface area =6.0 m² 1 Permitted element sizes according to B2 classification, coloured version Element height Element width System A / D not permitted element size with a rash height to sash width ratio of > 2:1 permitted element size with reinforcement : 58 x 45.5 x 2 mm not permitted sash size, coloured, max. 5.5 m², max. sash width 2.5 m Maximum sash surface area=5.5 m² Element height Element width System K System C / F General information 1.9

11 Maximum sizes 1 Permitted element sizes according to B3 classification, model in white and cream-white Element height Element width System A / D not permitted element size with a sash height to sash width ratio of > 2:1 permitted element size with reinforcement : 58 x 45.5 x 2 mm not permitted sash size, white max. 5.5 m 2, max. sash width 3.0 m Maximum sash surface area=5.5 m² Maximum element height 2.5 m Element height Element width System K System C / F Permissible element sizes according to B3 classification, coloured model Element height Element width System A / D not permitted element size with a sash height to sash width ratio of > 2:1 permitted element size with reinforcement : 58 x 45.5 x 2 mm not permitted sash size, coloured, max. 5.5 m², max. sash width 2.5 m Maximum sash surface area=5.5 m² Element height Element width System K System C / F General information

12 Permitted element sizes according to B4 classification, model in white and cream-white Element width System A / D non-permissible element size with a ratio sash height to sash width > 2:1 permissible element size with reinforcement : 58 x 45.5 x 2 mm non-permissible sash size, white max. 5.0 m2, max. sash width 3.0 m Maximum sash surface area=5.0 m² Maximum element height 2.3 m 1 Element width System K System C / F Permitted element sizes according to B4 classification, model in color Element height Element width System A / D not permitted element size with a sash height to sash width ratio of > 2:1 permitted element size with reinforcement : 58 x 45.5 x 2 mm not permitted sash size, coloured, max. 5.0 m², max. sash width 2.5 m Maximum sash surface area=5.0 m² Element height Element width System K System C / F General information 1.11

13 Wind load Wind load zone map 1 Due to the revision of DIN in March 2005, "Recommendations for the use of windows and external doors" (FE-05/1) have also been revised. Below you will find the updated wind load map as well as a table for simplified calculation of wind loads for Germany. Wind load zone 1 with 22.5 m/s Wind load zone 2 with 25.0 m/s Wind load zone 3 with 27.5 m/s Wind load zone 4 with 30.0 m/s 1.12 General information

14 Wind load Recommendations for the use of windows and external doors based on the simplified assumption of the wind loads of up to 25 m, to DIN (dated 2005) Criteria Wind load zone Window installation height in the central area 0 10 m Window installation height in the central area > m Window installation height in the central area m Inland Terrain category Terrain category Terrain category Baltic Sea North North Baltic Sea North Baltic Sea North Sea North North Sea Coast and Sea Sea Inland Coast and Sea Inland Coast and islands Sea Coast island islands Coast island islands Coast islands 1 B2-4A a -2 x x x B2-4A-3 x x x B2-4A-3 x x x Wind load in kn/m² 0.50 x x x 0.65 x x x 0.75 x x x 2 B2-4A-2 B2-4A-2 x x B2-4A-3 B3-7A-3 x x B2-4A-3 B3-7A-3 x x Wind load in x x x x x x kn/m² 3 B2-4A-2 B3-7A-2 x x B3-7A-3 B3-7A-3 x x B3-7A-3 B3-7A-3 x x Wind load in kn/m² x x x x x x B3- B3-4 B2-4A-2 B3-7A-2 B3-7A-3 B3-7A-3 B3-7A-3 7A-2 7A-3 Calculation B3-7A-3 B4-9A-3 B4-9A-3 Calculation Wind load in required required kn/m² Criteria Wind load zone 1-4 External door installation height in the central area 0 10 m External door installation height in the central area > m External door installation height in the central area > m B2-3A a -2 B2-3A a -2 must be determined separately must be determined separately 1 a The classification for driving rain resistance differentiates in wind load zone 1, in the terrain category "Inland with an installation height of up to 10 m between a protected position (B) and an unprotected position (A) for windows. External doors differentiation is made in wind load zones 1-4 with an installation height of up to 10 m, and in the terrain category "Inland" installation height of up to m, between a protected position (B) and an unprotected position (A). When installing windows at a height of more than 25 m in buildings that do not feature a square ground plan and in buildings erected at a height of over 800 m above sea level, a separate proof of wind load calculations must be provided according to DIN The above values are for reference only. In an exceptional case, hurricane force storms might result in draughts coming through windows and external doors. The above values only apply to the central area of the wall surface. In corner and edge areas, the wind load values must be increased by a factor 1.7. The corner and edge area is defined as 1/5 of the width of the building, applicable to all sides of the building. The central area comprises the entire remaining surface area. The value has been assumed for the worst case based on an edge area of 1 m² and a height/width ratio greater than or equal to 5.! Please note! The Energy Saving Regulation ("Energiesparverordnung" (EnEV) 10/2009 demands Class 3 air permeability for windows in buildings with more than two full storeys. Reference values for the classification in accordance with DIN A corresponds to B2-4A-1 B corresponds to B3-7A-2 C corresponds to B4-9A-3 Source: ift Directive FE-05/2. Recommendations for the use of windows and external doors - Part 1 (extract) i Information The above table is a Directive issued by ift (Institut für Fenstertechnik e.v. in Rosenheim) in August The table is no longer up-to-date and is currently being revised. General information 1.13

15 Suppliers 1 List of suppliers Fittings Gretsch-Unitas GmbH Johann-Maus-Straße 3 D Ditzingen Telephone: +49 (0) HAUTAU GmbH Bahnhofstraße D Helpsen Telephone: +49 (0) SIEGENIA-AUBI KG Industriestraße 1-3 D Wilnsdorf-Niederdielfen Telephone: +49 (0) ROTO Frank AG Wilhelm-Frank-Platz 1 (Stuttgarter Straße ) D Leinfelden-Echterdingen Telephone: +49 (0) Mayer & CO Beschläge GmbH Alpenstraße 173 A 5020 Salzburg Telephone: +43 (0) Assembly adhesive WEICON GmbH & Co. KG Königsberger Str. 255 D Münster Telephone: +49 (0) Screws SFS Intec Deutschland In den Schwarzwiesen 2 D Oberursel / TS Telephone: +49 (0) SFS Intec Schweiz Rosenbergsaustrasse 10 CH 9435 Heerbrugg Telephone: +41 (0) (Lift and slide door) extensions Frinorm AG Wärmedämmelemente Föhrenweg 9 FL 9496 Balzers Telephone: General information

16 Profile overview List of articles, numerical Main profiles Frame profile Film variants Threshold Sash profile Mullions Auxiliary profiles Auxiliary profiles Aluminum attachment facings Accessories

17 List of articles VEKASLIDE 2 i Info The profile overview comprises all articles that are mandatorily required for the VEKASLIDE. Any VEKA articles not listed, e.g. widening profiles etc. are shown and described in the PROFILE OVERVIEW VEKA SYSTEMS No The illustration of profiles and accessory parts in the list of articles a.o. is not to scale. If any figures have been drawn to scale, this is appropriately indicated. Details on frame kits and sash kits as well as threshold sets and fittings sets are given in the Chapter "Material". An overview of the respective set contents is given in the section "Accessories" from page Legend for article model versions PVC profiles: Aluminum profile: Films without Alu raw Film with/on both sides E6/EV1 = silver anodized Film, single-sided E6/C34 = brown anodized Film on request white/black = powder-coated Figure Art. no x 70 mm SOFTLINE 70 Height x Width / Area of application/use Model m/bar m/collar x 70 mm SOFTLINE x 25.4 mm for x 5.9 mm for x 88 mm for x 18.2 mm for x 18.2 mm for x 33 mm for Profile overview

18 List of articles VEKASLIDE Figure Art. no x 170 mm Threshold Height x Width / Area of application/use Model m/bar m/collar PVC light grey RAL 7035 in kit - not available separately Set x x 71 mm for Threshold set - Plan A complete Size Size Size Size Size x 68.3 mm for x 37.4 mm for x 29.8 mm for PVC light grey RAL 7035 PVC light grey RAL in kit and available separately in kit and available separately in kit - not available separately x 61 mm for x 14 mm for x 15.5 mm for x 36.3 mm for TPE light grey in kit and available separately in kit and available separately x 21.5 mm for Regenerat Kit Kit Kit Kit HST (lift/slide door) frame set, size 30 Height 2.30 m - white + cream-white Height 2.70 m - white + cream-white HST (lift/slide door) frame set size 35 Height 2.30 m - white + cream-white Height 2.70 m - white + cream-white HST (lift/slide door) frame set size 40 Height 2.30 m - white + cream-white Height 2.70 m - white + cream-white HST (lift/slide door) frame set size 50 Height 2.30 m - white + cream-white Height 2.70 m - white + cream-white 1 Set 1 Set 1 Set 1 Set 1 Set 1 Set 1 Set 1 Set Profile overview 2.3

19 List of articles VEKASLIDE Figure Art. no. Height x Width / Area of application/use Model m/bar m/collar 2 Kit Kit Kit Kit HST (lift/slide door) sash set size 30 Height 2.30 m - white + cream-white Height 2.70 m - white + cream-white HST (lift/slide door) sash set size 35 Height 2.30 m - white + cream-white Height 2.70 m - white + cream-white HST (lift/slide door) sash set size 40 Height 2.30 m - white + cream-white Height 2.70 m - white + cream-white HST (lift/slide door) sash set size 50 Height 2.30 m - white + cream-white Height 2.70 m - white + cream-white 1 Set 1 Set 1 Set 1 Set 1 Set 1 Set 1 Set 1 Set x 170 mm frame profile - white + cream-white - white + cream-white - white + cream-white - Type 1, 2, 3, 4, 5 - Type 1, 2, 3, 4, 5 - Type 1, 2, 3, unpunched punched without clip system x 69 mm - white + cream-white x 69 mm - white + cream-white x 45 mm - white + cream-white x 69 mm - white + cream-white - white + cream-white - white + cream-white unpunched punched 70.5 x 14.5 mm - white + cream-white - white + cream-white - Type x 14.5 mm - white + cream-white - white + cream-white - Type 1, 2, 3, x 55 mm - white + cream-white - white + cream-white x 38 mm - white + cream-white x 38 mm - white + cream-white x 70 mm sash - white + cream-white - white + cream-white Profile overview

20 List of articles VEKASLIDE Figure Art. no. Height x Width / Area of application/use Model m/bar m/collar for T profiles with reinforcement chamber 38/30 black 100 pcs for T profile 118 mm silver 50 pcs for Plan D + F black in set not available separately for Plan D + F grey in set not available separately for black in set not available separately for Plan C + F / grey, black in set not available separately for / light grey in set not available separately for / grey in set not available separately for / light grey in set not available separately for / light grey in set not available separately for / light grey in set not available separately Sealing plate, top light grey in set not available separately Set Set BSZ connectors for / Connector light grey in set not available separately Sealing plate, bottom light grey in set not available separately for grey in set not available separately for grey in set not available separately for / grey in set not available separately for grey in set not available separately 2 1 Set Profile overview 2.5

21 List of articles VEKASLIDE 2 Figure Art. no. Height x Width / Area of application/use Model m/bar m/collar for Plan D + F light grey in set - not available separately for Plan C + F for / grey in set - not available separately T profile 85 mm silver 50 pcs. 50 pcs. Set Sealing set VEKASLIDE frame 1 Set Set Sealing set VEKASLIDE sash 1 Set Set Sealing set Plan C + F, VEKASLIDE 1 Set Set Sealing set Plan D + F, VEKASLIDE 1 Set x 36 mm, with seal, grey 21 x 36 mm, with seal, black x 23 mm, with seal, grey 21 x 23 mm, with seal, black x 23 mm, with seal, grey 21 x 23 mm, with seal, black x 20 mm, with seal, grey 21 x 20 mm, with seal, black x 17 mm, with seal, grey 21 x 17 mm, with seal, black x 14 mm, with seal, grey 21 x 14 mm, with seal, black x 11 mm, with seal, grey 21 x 11 mm, with seal, black x 32 mm, with seal, grey 21 x 32 mm, with seal, black x 29 mm, with seal, grey 21 x 29 mm, with seal, black x 26 mm, with seal, grey 21 x 26 mm, with seal, black x 6 mm, with seal, grey 21 x 6 mm, with seal, black Profile overview

22 List of articles VEKASLIDE Figure Art. no. Height x Width / Area of application/use x 23 mm, with seal, grey 21 x 23 mm, with seal, black Model m/bar m/collar x 23 mm, with seal, grey 21 x 23 mm, with seal, black x 31.5 mm, with seal, grey 21 x 31.5 mm, with seal, black x 23.5 mm, with seal, grey 21 x 23.5 mm, with seal, black x 19.5 mm, with seal, grey 21 x 19.5 mm, with seal, black x 15.5 mm, with seal, grey 21 x 15.5 mm, with seal, black x 11.5 mm, with seal, grey 21 x 11.5 mm, with seal, black x 40 mm, with seal, grey 21 x 40 mm, with seal, black x 21.5 mm, with seal, grey 21 x 21.5 mm, with seal, black x 23.5 mm, with seal, grey 21 x 23.5 mm, with seal, black x 7.5 mm, with seal, grey 21 x 7.5 mm, with seal, black x 17.5 mm, with seal, grey 21 x 17.5 mm, with seal, black x 23.5 mm, with seal, grey 21 x 23.5 mm, with seal, black x 19.5 mm, with seal, grey 21 x 19.5 mm, with seal, black x 17.5 mm, with seal, grey 21 x 17.5 mm, with seal, black x 15.5 mm, with seal, grey 21 x 15.5 mm, with seal, black x 23.5 mm, with seal, grey 21 x 23.5 mm, with seal, black Nipple head screw silver 1000 pcs. Profile overview 2.7

23 List of articles VEKASLIDE 2 Figure Art. no. Height x Width / Area of application/use x 69.5 mm for white + cream-white - white Model m/bar m/collar for as a sliding sash light grey in set - not available separately for / /fixed sash white, black in set - not available separately for as a fixed sash blue in set - not available separately Set Accessories set, sash VEKASLIDE 1 Set yellow 100 pcs. Set x Sealing set for size 30/ Sealing set for size 40/ Sealing set for size 65 black, grey black, grey black, grey Seal for black grey caramel 1 Set 1 Set 1 Set Seal for black Seal for black Seal for black Seal for with aluminum tray black grey x 30 mm for /RC x 22 mm for / x 58 mm for x 58 mm for Profile overview

24 List of articles VEKASLIDE Figure Art. no x 34 mm for Height x Width / Area of application/use Model m/bar m/collar Set x Fittings sets: for size 30/35/ for size for size 65 EV1 silver 1 Set 2 Accessories Fittings accessories: Set of latch parts, Plan C + F 1 Set Accessories Fittings accessories: Corner guide, Plan C + F 1 pc. Accessories Fittings accessories: Gear extension 1 pc. Accessory Fittings accessory: for two-sided handle set, silver 1 pc. Accessory Fittings accessory: Additional carriage pc Oval head screw T 30, Ø 6.5 x 110 mm 100 pcs. in set Insulating wedge for grey Insulating wedge for grey Insulating wedge for grey drilling jig for frame/threshold connection 1 pc Drilling jig for T connection 1 pc. Profile overview 2.9

25 Frame profile 2 Frame profile 50 mm Article no. Model * Colour Film application Always state model version in addition to the article no. without two-sided single sided * on request see next page for detailed information Seal without required accessory Alu reinforcement 125 x 34 mm Insulating wedge M.1: Profile overview

26 Film variants Film variants, single colour Type 1 Film outside + inside outside inside 2 Type 2 Film outside outside Type 3 Film inside Film variants, 2-colour Type 4 Film outside + inside outside inside inside Type 5 Film outside + inside outside inside i Info All film variants are available in the lengths 3020 mm, 5250 mm and 6500 mm. Profile overview 2.11

27 Threshold VEKA Exotherm Threshold VEKA Exotherm 1.5 in kit - not available separately Article no. Model Colours Alu silver anodized PVC light grey RAL 7035 optional accessories Insulating wedge Insulating wedge Aluminum running rail, external Alu weather sides, standard Kit comprising Threshold Cap profile, outside PVC light grey RAL Alu threshold cover, outside Alu adapter profile for weather sides SFS Alu weather sides, Switzerland no VEKA article Drilling template, threshold /frame Alu running rail, internal Sealing profile! Please note! Drilling template is required for first order! Threshold cover, internal, Standard M.1: Profile overview

28 Sash Sash 100 mm required accessory Reinforcement, fixed sash 45.5 x 58 x 2 mm I x = cm 4, I y = 7.43 cm 4 Article no. Model * Colour Film application Always state model version in addition to the article no. without two-sided single sided * on request Seal without Reinforcement, sliding sash 45.5 x 58 x 2 mm I x = cm 4, I y = 8.65 cm Reinforcement RC 2 22 x 7.5 x 2 mm I x = 0.03 cm 4, I y = 0.37 cm Spacer FS Glazing rebate insert yellow Y X Seal Seal R R M.1:1 Profile overview 2.13

29 T-profiles 2 T profile 85 mm Mullion Article no. Model Colour Film application Always state model version in addition to the article no. without two-sided single sided Seal without with required accessory Reinforcement 38 x 30 x 1.5 mm I y = 2.55 cm 4, I x = 3.68 cm Reinforcement 38 x 30 x 4.0 mm I y = 5.48 cm 4, I x = 8.10 cm Connector incl. sealing plate Sealing plug for horizontal use Glazing rebate insert yellow Y X Seal R = = M.1: Profile overview

30 T-profiles T profile 118 mm Mullion Article no. Model Colour Film application Always state model version in addition to the article no. without two-sided single sided Seal without with required accessory Reinforcement 38 x 30 x 1.5 mm I y = 2.55 cm 4,, I x = 3.68 cm Reinforcement 38 x 30 x 4.0 mm I y = 5.48 cm 4, I x = 8.10 cm Connector incl. sealing plate Sealing plug for horizontal use Glazing rebate insert yellow Y X Seal R = = M.1:1 Profile overview 2.15

31 Auxiliary profiles Spacer profile for frame 23 x 69 mm with sealing lips, black Model version: white and film-covered Model version: unpunched and punched (detailed information is given in Chapter 5 "Processing") 17 2 Article no * with clip system required accessory 69 Spacing profile for sash 16.9 x 45 mm 14 without clip system for central section, Plan C and F Model version: white and film-covered 45 Article no * without clip system required accessory Cover profile 2.5 x 69.5 mm Model version: white and film-covered Article no required accessory M.1:2 / Film application without two-sided single-sided * on request 2.16 Profile overview

32 Auxiliary profiles Guide profile 29 x 69 mm with sealing lips, black Model version: white and film-covered Article no. required accessory * Aluminum guide profile Aluminum guide profile 7 x 25.4 mm Model versions; silver and brown Article no. required accessory Guide profile Hingeing profile 25 x 26.5 mm Model version: white and film-covered Article no. required accessory * Seal, black Cover profile 13 x 38 mm Model version: white and film-covered Article no * required accessory M.1:2 / Film application without two-sided single-sided * on request Profile overview 2.17

33 Auxiliary profiles Cover profile for sash 14.5 x 70.5 mm 4 Model versions: white and film-covered (for detailed information see on the right) Model version: unpunched and punched (detailed information is given in Chapter 5 "Processing") Article no * required accessory 7.5 Film application Type 1 Type 2 Type 3 Type 4 Film application, type 1 Film application, types 2, 3 and 4 for central section Plan C and F outside outside inside inside Spacing profile for sash 21.5 x 47.2 mm 21.5 for fixed sash, Variant Plan C Model: Regenerat Article no required accessory 47.2 Center sealing bead 55 x 23 mm 7 Model version: white and film-covered (film application, type 1) Article no. required accessory * Seal, black Nipple head screw 8 mm Reinforcement, RC x 22 x 2 mm trade standard Screw for RC 2 Ø 4.8 x 40 mm RC 2 M.1:2 / Film application without two-sided single-sided * on request 2.18 Profile overview

34 Auxiliary profiles Cap profile 22.3 x 71 mm 71 in kit for threshold VEKA Exotherm 1.5 with sealing lips, black Design: light grey RAL Article no. required accessory Aluminum running rail, external 2 Aluminum running rail, external 14.8 x 29.8 mm Design: silver, anodized required for Plan D and F Article no required accessory Alu running rail, internal 14.8 x 37.4 mm 37.4 in kit - not available separately Design: silver, anodized 8 Article no. required accessory Sealing profile Sealing profile 6.5 x 15.5 mm 15.5 in kit for threshold VEKA Exotherm 1.5/Alu running rail, internal Design: TPE light grey 6.5 Article no. required accessory Alu running rail, internal M.1:2 / Model version E6/EV1 = silver anodized E6/C34 = brown anodized white/brown = coated with synthetic powder Profile overview 2.19

35 Auxiliary profiles Threshold cover, internal 8.3 x 36.3 mm 36.4 in kit for threshold VEKA Exotherm 1.5 Design: silver, anodized required for Plan D and F, otherwise optional 2 Article no required accessory Threshold cover, external 11.5 x 68.3 mm 65.1 in kit for threshold VEKA Exotherm 1.5 Design: silver, anodized 11.5 Article no required accessory Alu weather sides 29 x 61 mm for threshold VEKA Exotherm 1.5 Standard Design: silver, anodized Article no. required accessory EPDM sealing track, black Alu adapter profile 14 x 26 mm for threshold VEKA Exotherm 1.5 for window sill by Messrs. SFS Model: raw Article no. required accessory SFS Alu weather sides M.1:2 / Model version E6/EV1 = silver anodized E6/C34 = brown anodized white/brown = coated with synthetic powder 2.20 Profile overview

36 Aluminum attachment facings Alu front facing 65.5 x 5.9 mm for frame profile Model: raw Article no Alu front facing 88 x 27 mm required accessory 2 for frame profile Model: raw 27 Article no. required accessory Seal, black 88 Alu front facing 104 x 18.2 mm 104 for sash Model: raw 18.2 Article no. required accessory Seal, grey and black Alu front facing x 18.2 mm for Plan C and F Sash with spacer strip Model: raw 18.2 Article no. required accessory Seal, grey and black M.1:2 / Model version E6/EV1 = silver anodized E6/C34 = brown anodized white/brown = coated with synthetic powder Profile overview 2.21

37 Aluminum attachment facings Alu front facing 85.4 x 33 mm 2 for sash with center sealing bead Model: raw Article no. required accessory Center sealing bead M.1:2 / Model version E6/EV1 = silver anodized E6/C34 = brown anodized white/brown = coated with synthetic powder 2.22 Profile overview

38 Accessories Sealing set, frame Article no comprising Model Fig pcs. Sealing part 16 self-adhesive black pcs. Sealing part 1 light grey pcs. Sealing plug self-adhesive grey pair Sealing part 2 light grey pair Sealing part 3 light grey pair Sealing part 4 light grey Set BSZ connectors Connection of threshold and frame Article no comprising Model Fig pc. Sealing plate, top light grey pc. Connector light grey pc. Sealing plate, bottom light grey 9 9 BSZ drilling template Connection of threshold/frame and frame/frame Article no. Fig Profile overview 2.23

39 Accessories Sealing set, sash Article no comprising Model Fig pair Sealing part 7 self-adhesive pc. Sealing part 8 self-adhesive pc. Sealing part 9 self-adhesive pc. Sealing part 10 self-adhesive grey 1 grey 2 grey 3 grey pcs. End cap 1 x black, 1x white Sealing set Plan C + F Article no comprising Model Fig pc. Sealing part 15 for Plan C and F pc. Sealing part 14 for Plan C and F grey 6 grey Sealing set, plan D + F Article no comprising Model Fig pc. Sealing plate, selfadhesive for Plan D and F pc. Sealing pad, selfadhesive for Plan D and F grey 8 black pair Sealing part 4 for Plan F pcs. Draining bridge for Plan D and F light grey 10 light grey Profile overview

40 Accessories Accessories set, sash Article no comprising Model Fig pcs. Nipple head screw 8 mm silver pcs. Guide slide light grey RAL pcs. Spacers for fixed sash pcs. Oval head screw T 30, Ø 6.5x110 mm blue 3 galvanized Sealing set Article no x , size 30/35, black, grey , size 40/50, black, grey , size 65, black, grey comprising Model Fig Size 30/35 Size 40/50 Size m 21 m 25 m Seal for black, grey m Seal for black Size 30/35 Size 40/50 Size 65 2 x 16 m 2 x 20 m 2 x 24 m Seal for black Size 30/35 Size 40/50 Size m 2.6 m 3.2 m Seal for black 6 Profile overview 2.25

41 Accessories Profile overview

42 Profile combinations Element cross-sections, horizontal 3.2 Standard profile combinations Scale 1: Profile combinations with Aluminum attachment facings Connection, bottom, all plans VEKAVARIANT Skylight Ventilation i Info This chapter only shows VEKASLIDE profile combinations. Processing guidelines for the various plans are found in the Chapter "Processing. 3.1

43 Element cross-section, Plan A/D 3 70 Plan A Plan D Profile combinations

44 Element cross-section, Plan K Plan K Plan K 3 part with mullion Profile combinations 3.3

45 Element cross-section, horizontal, Plan C/F 3 Plan C Plan F Profile combinations

46 Element cross-section, Variant, Plan C Variant: Plan C Profile combinations 3.5

47 Standard profile combinations M. 1:2 Plan A Detail cross-section, vertical Fixed sash, outside Plan K Detail cross-section, vertical Fixed sash, outside Plan C Detail cross-section, vertical Fixed sash, outside 3 Frame profile Spacing profile Cover profile Guide profile Aluminum guide profile Sash Cap profile Threshold Alu cover profile Alu running rail Profile combinations

48 Standard profile combinations M. 1:2 Plan A Detail cross-section, vertical Sliding sash, inside Plan K Detail cross-section, vertical Sliding sash, inside Plan C Detail cross-section, vertical Sliding sash, inside Frame profile Cover profile Hingeing profile Guide profile Aluminum guide profile Sash Alu cover profile Alu running rail Threshold Profile combinations 3.7

49 Standard profile combinations M. 1:2 Plan A Detail cross-section, horizontal Sliding sash, incl. handle Plan D Detail cross-section, horizontal Sliding sash, incl. handle Plan K Detail cross-section, horizontal Sliding sash, incl. handle 3 Frame profile Spacing profile Sash Standard: Gauge 27.5 mm, Handle seat 1005 mm up to 300 kg sash weight optional: Gauge 37.5 mm, Handle seat 1005 mm Sash and reinforcement must be pre-milled! Please note! In order to achieve burglary resistance RC 2 the gauge 37.5 mm is mandatorily required (protection against opening by drilling). 3.8 Profile combinations

50 Standard profile combinations M. 1:2 Plan A Detail cross-section, horizontal Fixed sash Plan C Detail cross-section, horizontal Fixed sash Sash Spacing profile Frame profile Profile combinations 3.9

51 Standard profile combinations M. 1:2 Plan A Detail cross-section, horizontal Central section Plan D Detail cross-section, horizontal Central section Plan K Detail cross-section, horizontal Central section 3 Plan C + F Detail cross-section, horizontal Central section 4 Standard model Cover profile Center sealing bead Sash Profile combinations

52 Standard profile combinations M. 1:2 Plan A Detail cross-section, horizontal Central section Model RC 2 Plan D Detail cross-section, horizontal Central section Model RC 2 Plan K Detail cross-section, horizontal Central section Model RC 2 Plan C + F Detail cross-section, horizontal Central section Model RC 2 3 Variant 1 RC 2 Variant 2 RC Cover profile Center sealing bead Sash ! Please note! For RC 2 various different variants of additional steel reinforcement in the sliding sash are possible. Profile combinations 3.11

53 Standard profile combinations M. 1:2 Plan C + F Detail cross-section, horizontal Central section 3 Sash Cover profile Spacing profile ! Please note! Pay attention to film types of the frame and cover profile (see pages 2.11 and 2.18) Profile combinations

54 Notes 3 Profile combinations 3.13

55 Standard profile combinations M. 1:2 Variant: Plan C Detail cross-section, vertical Fixed sash, inside 3 Frame profile Cover profile Hingeing profile Guide profile Aluminum guide profile Sash Alu cover profile Spacing profile Alu running rail Threshold Profile combinations

56 Standard profile combinations M. 1:2 Variant, Plan C Detail cross-section, horizontal Central section Sash Spacing profile Cover profile Profile combinations 3.15

57 Standard profile combinations M. 1:2 Plan D Detail cross-section, vertical Sliding sash, outside Plan F Detail cross-section, vertical Sliding sash, outside 3 Frame profile Guide profile Aluminum guide profile Guide profile Aluminum guide profile Cover profile Sash Alu running rail Cap profile Alu cover profile Alu running rail Threshold Profile combinations

58 Standard profile combinations M. 1:2 Plan D Detail cross-section, vertical Sliding sash, inside Plan F Detail cross-section, vertical Sliding sash, inside Frame profile Guide profile Aluminum guide profile Guide profile Aluminum guide profile Hingeing profile Sash Alu running rail Cap profile Alu cover profile Alu running rail Threshold Profile combinations 3.17

59 Profile combinations with Alu attachment facings Plan A Detail cross-section, vertical Fixed sash, outside Plan K Detail cross-section, vertical Fixed sash, outside Plan C Detail cross-section, vertical Fixed sash, outside 3 Frame profile Alu attachment facing Spacing profile Cover profile Guide profile Aluminum guide profile Sash Alu attachment facing Cap profile Threshold Alu cover profile Alu running rail Profile combinations

60 Profile combinations with Alu attachment facings Plan A Detail cross-section, vertical Sliding sash, inside Plan K Detail cross-section, vertical Sliding sash, inside Plan C Detail cross-section, vertical Sliding sash, inside Frame profile Alu attachment facing and Guide profile Aluminum guide profile Sash Alu attachment facing Alu running rail Cap profile Alu cover profile Alu running rail Threshold Profile combinations 3.19

61 Profile combinations with Alu attachment facings Plan A Detail cross-section, horizontal Sliding sash, incl. handle Plan K Detail cross-section, horizontal Sliding sash, incl. handle Frame profile Alu attachment facing and Spacing profile Sash Alu attachment facing Standard: Gauge 27.5 mm up to 300 kg sash weight optional: Gauge 37.5 mm Sash and reinforcement must be pre-milled 170! Please note! In order to achieve burglary resistance RC 2 the gauge 37.5 mm is mandatorily required (protection against opening by drilling) Profile combinations

62 Profile combinations with Alu attachment facings Plan A Detail cross-section, horizontal Fixed sash Plan C Detail cross-section, horizontal Fixed sash Sash Alu attachment facing Spacing profile Frame profile Alu attachment facing Profile combinations 3.21

63 Profile combinations with Alu attachment facings Plan A Detail cross-section, horizontal Central section Plan D Detail cross-section, horizontal Central section Plan K Detail cross-section, horizontal Central section 3 Plan C + F Detail cross-section, horizontal Central section 104 Alu attachment facing Sash Alu attachment facing Center sealing bead Sash Alu attachment facing (abbreviated) 70 Cover profile Profile combinations

64 Profile combinations with Alu attachment facings Plan C + F Detail cross-section, horizontal Central section 3 Sash Alu attachment facing Cover profile Spacing profile Sash Alu attachment facing Profile combinations 3.23

65 Connection, bottom, all plans 3 Additional profiles for threshold No. 1 Designation VEKA Exotherm 1.5, threshold, standard No. 2 Designation VEKA Exotherm 1.5, threshold, standard Weather sides 47 mm No. 3 Designation VEKA Exotherm 1.5, threshold, standard Adapter for weather sides SFS Weather sides 50 mm, no VEKA article No. 1 side frame No Roller shutter guide side frame 47 No Roller shutter guide side frame Profile combinations

66 Connection, bottom, all plans Widening 15 x 70 mm 15 Article no. required accessory Drive-in anchor, rotatable Widening 30 x 70 mm Model version: white and film-covered Article no. required accessory Reinforcement 38 x 15 mm Drive-in anchor, rotatable Widening 45 x 70 mm Model version: white and film-covered 45 Article no. required accessory Reinforcement 38 x 30 x 1.5 mm Drive-in anchor, rotatable Profile combinations 3.25

67 Connection, bottom, all plans Widening 100 x 70 mm Model version: white and film-covered Article no. required accessory Reinforcement 38 x 30 x 1.5 mm Drive-in anchor, rotatable Widening 250 x 70 mm Model version: white and film-covered Article no. required accessory Reinforcement 38 x 30 x 1.5 mm Drive-in anchor, rotatable Profile combinations

68 Connection, bottom, all plans Balcony connection profile 43 x 49 mm Article no processed required accessory Reinforcement 30 x 30 mm Drive-in anchor Balcony connection profile 100 x 49 mm Article no processed required accessory Reinforcement 30 x 30 mm Drive-in anchor Balcony connection profile 130 x 49 mm Article no processed required accessory Reinforcement 30 x 10 mm Reinforcement 30 x 30 mm Drive-in anchor i Info Balcony connection profiles must be processed. Profile combinations 3.27

69 VEKAVARIANT 235 VEKASLIDE, all plans Detail cross-section, vertical, inc. roller shutter box Sliding sash Article no. Designation Profile set Standard VEKAVARIANT i Info Only revision at the front possible. Roll-off profile - Standard ( ) must be processed. Note the attachment of the top frame ( ) Profile combinations

70 VEKAVARIANT 235 VEKASLIDE, all plans Detail cross-section, horizontal Sliding sash and central section with roller shutter guide Roller shutter guide Widening Double roller shutter guide i Info Illustration is schematic only. Note the window statics! Only electrical drive possible! A double roller shutter guide can only be fitted to the fixed sash: Plan A/K/C. Detailed information on the VEKAVARIANT e.g. maximum sizes, processing, etc. is provided in the Technical Information VEKAVARIANT No Profile combinations 3.29

71 Skylight VEKASLIDE Detail cross-sections vertical/horizontal Tiltable skylight and sliding sash Skylight fitted in frame construction 3 Detail cross-section, vertical Attachment frame T profile Sash Detail cross-section, horizontal Central section, skylight Weather sides Frame Coupling profiles Detail cross-section, horizontal Central section, VEKASLIDE 104 i Info Illustration schematic only. Note window statics/maximum sizes! Fitting an attachment frame ( , shown in the example) to a fixed sash only: Plan A/K/C Profile combinations

72 Skylight VEKASLIDE Detail cross-sections vertical/horizontal Tiltable skylight and sliding sash Skylight fitted separately on frame construction Detail cross-section, vertical Attachment frame T profile Sash Detail cross-section, horizontal Central section, skylight Frame Coupling profiles Detail cross-section, horizontal Central section, VEKASLIDE 104 i Info Illustration schematic only. Note window statics/maximum sizes! Fitting an attachment frame ( , shown in the example) to a fixed sash only: Plan A/K/C. Profile combinations 3.31

73 Ventilation, GU Plan A Detail cross-section, horizontal incl. ventilation Plan D Detail cross-section, horizontal incl. ventilation Plan K Detail cross-section, horizontal incl. ventilation 3 Plan F Detail cross-section, horizontal incl. ventilation! Please note! changed sash subtraction dimensions (EW) Plan A and D = SW = EW/ mm Plan K = SW = EW/3 + 6 mm Sliding sash, closed Widening Fan incl. seal GU article Sliding sash in ventilation position Profile combinations

74 Ventilation, SIEGENIA-AUBI Plan A Detail cross-section, horizontal incl. ventilation Plan D Detail cross-section, horizontal incl. ventilation Plan K Detail cross-section, horizontal incl. ventilation Plan F Detail cross-section, horizontal incl. ventilation i Info The fittings sets by SIEGENIA-AUBI each contain 1x extended latch bolt (bottom) as standard. 3 Sliding sash, closed Sliding sash in ventilation position Profile combinations 3.33

75 Profile combinations

76 Material Cut-out dimensions Subtraction dimensions Cut-out dimensions/ Finished dimensions Kits

77 Cut-out dimensions, vertical Subtraction dimensions, vertical for two-part or multi-part sliding elements All plans 4 EH SH GM GB SH Cut-out dimensions, vertical Sash height Glazing bead Glass measure = EH mm = SH mm = SH mm Additional subtraction dimensions for the required profiles are shown from page 4.10 Abbreviations: EW EH SW SH FS GB GM SS = Element Width = Element Height = Sash Width = Sash Height = Fixed Sash = Glazing bead = Glass Measure = Sliding Sash 4.2 Material

78 Cut-out dimensions, horizontal Cut-out dimensions, horizontal for two-part sliding elements Plan A + D Plan A Plan D EW SW GM GB SW Cut-out dimensions, horizontal Sash width Glazing bead Glass measure = EW/2-17 mm = SW mm = SW mm Additional subtraction dimensions for the required profiles are shown from page 4.10 Abbreviations: EW EH SW SH FS GB GM SS = Element Width = Element Height = Sash Width = Sash Height = Fixed Sash = Glazing bead = Glass Measure = Sliding Sash Material 4.3

79 Cut-out dimensions, horizontal Cut-out dimensions, horizontal for three-part sliding elements Plan K Plan K EW SW GM GB SW Cut-out dimensions, horizontal Sash width Glazing bead Glass measure = EW/ mm = SW mm = SW mm Additional subtraction dimensions for the required profiles are shown from page 4.10 Abbreviations: EW EH SW SH FS GB GM SS = Element Width = Element Height = Sash Width = Sash Height = Fixed Sash = Glazing bead = Glass Measure = Sliding Sash 4.4 Material

80 Cut-out dimensions, horizontal Cut-out dimensions, horizontal for three-part sliding elements Plan K with uneven subdivision, Fixed element = 2 x Sliding element Plan K 48 EW SW GB GM 65 4 GM SW GB GM SW GB Cut-out dimensions, horizontal Sash Width (= SW) Sash Width (= FS) Glazing bead Glass measure = EW/ mm = EW/ mm = SW mm = SW mm Additional subtraction dimensions for the required profiles are shown from page 4.10 Abbreviations: EW EH SW SH FS GB GM SS = Element Width = Element Height = Sash Width = Sash Height = Fixed Sash = Glazing bead = Glass Measure = Sliding Sash Material 4.5

81 Cut-out dimensions, horizontal Cut-out dimensions, horizontal for four-part sliding elements Plan C + F Plan C Plan F SW GB GM EW 4 20 GM GB SW 48 Cut-out dimensions, horizontal Sash width Glazing bead Glass measure = EW/ mm = SW mm = SW mm Additional subtraction dimensions for the required profiles are shown from page 4.10 Abbreviations: EW EH SW SH FS GB GM SS = Element Width = Element Height = Sash Width = Sash Height = Fixed Sash = Glazing bead = Glass Measure = Sliding Sash 4.6 Material

82 Cut-out dimensions, horizontal Cut-out dimensions, horizontal for three-part sliding elements Variant: Plan C Variant: Plan C EW SW GB GM GM GB SW 18 SW Cut-out dimensions, horizontal Sash width Glazing bead Glass = EB/3-17 mm = SW mm = SW mm Additional subtraction dimensions for the required profiles are shown from page 4.10 Abbreviations: EW EH SW SH FS GB GM SS = Element Width = Element Height = Sash Width = Sash Height = Fixed Sash = Glazing bead = Glass Measure = Sliding Sash Material 4.7

83 Cut-out dimensions, horizontal, including window gap vent Cut-out dimensions, horizontal for two-part sliding elements incl. window gap vent devices by Messrs- GU Plan A + D Plan A Plan D EW SW GM GB 48 SW Cut-out dimensions, horizontal Sash width Glazing bead Glass measure = EW/ mm = SW mm = SW mm Additional subtraction dimensions for the required profiles are shown from page 4.10 Abbreviations: EW EH SW SH FS GB GM SS = Element Width = Element Height = Sash Width = Sash Height = Fixed Sash = Glazing bead = Glass Measure = Sliding Sash 4.8 Material

84 Cut-out dimensions, horizontal, including window gap vent Cut-out dimensions, horizontal for three-part sliding elements incl. window gap vent devices by Messrs- GU Plan K Plan K EW SW GM GB SW 48 Cut-out dimensions, horizontal Sash width Glazing bead Glass measure = EW/3-6 mm = SW mm = SW mm Additional subtraction dimensions for the required profiles are shown from page 4.10 Abbreviations: EW EH SW SH FS GB GM SS = Element Width = Element Height = Sash Width = Sash Height = Fixed Sash = Glazing bead = Glass Measure = Sliding Sash Material 4.9

85 Subtraction dimensions, Plan A Item Figure Designation Art.- No. 1 Frame profile Frame reinforcement Insert W=Width H=Height Quantity Subtraction dimensions Plan A (in mm) W 1 EW (Element Width) H 2 EH-100 W 1 EW (Element Width) H 2 EH Spacing profile w. clip-on system H 45 1 SH+17 (1-side mitred) H 1 SH+17 (1-side punched)) Frame W 45 1 SW+2 (1-side mitred) 4 Guide profile W 1 EW Aluminum guide profile W 1 EW Hingeing profile W 1 SW-85 7 Cover profile (frame) W 1 SW-60 8 Cover profile (frame) W 1 SW-68 9 Sash profile Reinforcement (C profile) W 45 4 SW = EW/2-17 H 45 4 EH =EH-117 W 2 SW-165 H 1 SH Reinforcement (closed) Cover profile (sash) W 2 SW- 165 H 3 SH-165 H 1 SH+13 H 1 SH-2 Sash 13 Center sealing bead H 1 SH+15 H 1 SH-2 14 Glazing bead* e.g W 4 SW-158 H 4 SH-158 Abbreviations: Symbols: EW= Element width *= not included in kit SW = Sash width = needs to be ordered separately SH= Sash height 45 = mitre cutting! Please note! All details specified are theoretical in nature and do not take into account any welding allowances. All details are given without any express or implied warranty whatsoever! 4.10 Material

86 Subtraction dimensions, Plan A Item Figure Designation Art.- No. Insert W=Width H=Height Quantity Subtraction dimensions Plan A (in mm) 15 Threshold W 1 EW (Element Width) 16 Cap profile W 1 SW Threshold cover, external W 1 SW Running rail, internal W 1 EW-117 Threshold 19 Sealing profile, running rail W 1 EW Threshold cover, internal W 1 SW-81 Accessories 21 Sealing set, frame BSZ connector set Sealing set, sash Accessories set, sash Accessories set, seal ! Please note! All details specified are theoretical in nature and do not take into account any welding allowances. All details are given without any express or implied warranty whatsoever! Material 4.11

87 Subtraction dimensions Plan K Item Figure Designation Art.- No. 1 Frame profile Insert W=Width H=Height Subtraction dimensions Quantity Plan K (in mm) W 1 EW (Element Width) H 2 EH Frame reinforcement Spacing profile w. clip-on system W 1 EW (Element Width) H 2 EH-100 H 2 SH +17 (both punched) W 1 SW-26 Frame 4 Guide profile W 1 EW Aluminum guide profile W 1 EW Hingeing profile W 2 SW Cover profile (frame) W 1 SW Cover profile (frame) W 2 SW-68 9 Sash profile W 6 SW = W/ H 45 6 EH = H Reinforcement (C profile) W 2 SW Reinforcement (closed) Cover profile (sash) W 4 SW -165 H 6 SH -165 H 2 SH+13 H 2 SH-2 Sash 13 Center sealing bead 14 Glazing bead* (incl ) e.g H 2 SH+15 H 2 SH-2 W 6 SW-158 H 6 SH-158 Abbreviations: Symbols: EW= Element width *= not included in kit SW = Sash width = needs to be ordered separately SH= Sash height 45 = mitre cutting! Please note! All details specified are theoretical in nature and do not take into account any welding allowances. All details are given without any express or implied warranty whatsoever! 4.12 Material

88 Subtraction dimensions Plan K Item Figure Designation Art.- No. Insert W=Width H=Height Quantity Subtraction dimensions Plan K (in mm) 15 Threshold W 1 EW (Element Width) 16 Cap profile W 1 SW Threshold cover, external W 2 SW Running rail, internal W 1 EW-134 Threshold 19 Sealing profile, running rail W 1 EW Threshold cover, internal W 1 SW-192 Accessories 21 Sealing set, frame BSZ connector set Sealing set, sash Accessories set, sash Accessories set, seal ! Please note! All details specified are theoretical in nature and do not take into account any welding allowances. All details are given without any express or implied warranty whatsoever! Material 4.13

89 Subtraction dimensions, Plan C Item Figure Designation Art.- No. Insert W=Width H=Height Quantity Subtraction dimensions Plan C (in mm) 1 Frame profile W 1 EW (Element Width) H 2 EH Frame reinforcement Spacing profile w. clip-on system W 1 EW (Element Width) H 2 EH-100 W 45 2 SW+3 (2 x 1-side mitred) H 45 2 SH+17 (2 x 1-side mitred) Frame 4 Guide profile W 1 EW Aluminum guide profile W 1 EW Hingeing profile W 1 2 x SW Cover profile (frame) W 2 SW-60 8 Cover profile (frame) W 1 2 x SW Sash profile Reinforcement (C profile) Reinforcement (closed) W 45 8 SW = W/4+11 H 45 8 EH-117 W 4 SW-165 H 2 SH-165 W 4 SW -165 H 6 SH Spacing profile w/o clip-on system H 1 SH-15 Sash 13 Cover profile (sash) H 2 SH+13 H 3 SH-2 14 Center sealing bead H 2 SH+15 (incl ) H 2 SH-2 15 Glazing bead* e.g W 8 SW-158 H 8 SH-158 Abbreviations: Symbols: EW= Element width *= not included in kit SW = Sash width = needs to be ordered separately SH= Sash height 45 = mitre cutting! Please note! All details specified are theoretical in nature and do not take into account any welding allowances. All details are given without any express or implied warranty whatsoever! 4.14 Material

90 Subtraction dimensions, Plan C Item Figure Designation Art.- No. Insert W=Width H=Height Quantity Subtraction dimensions Plan C (in mm) 16 Threshold W 1 EW (Element Width) 17 Cap profile W 2 SW Threshold cover, external W 1 1 x SW Running rail, internal W 1 EW-100 Threshold 20 Sealing profile, running rail W 1 EW Threshold cover, internal W 2 SW-81 Accessories 22 Sealing set, frame BSZ connector set Sealing set, sash Accessories set, sash x Accessories set, seal Sealing set Plan C, F ! Please note! All details specified are theoretical in nature and do not take into account any welding allowances. All details are given without any express or implied warranty whatsoever! Material 4.15

91 Subtraction dimensions, Variant, Plan C Item Figure Designation Art.- No. Insert W=Width H=Height Quantity Subtraction dimensions, Variant, Plan C (in mm) 1 Frame profile W 1 EW (Element Width) H 2 EH Frame reinforcement Spacing profile w. clip-on system W 1 EW (Element Width) H 2 EH-100 W 1 SW+2 (1 x 1-side mitred) H 2 45 SH+17 (1 x 1-side mitred) Frame 4 Guide profile W 1 EW Aluminum guide profile W 1 EW Hingeing profile W 1 2 x SW Cover profile (frame) W 1 SW-60 8 Cover profile (frame) W 1 2 x SW-50 9 Sash profile Reinforcement (C profile) Reinforcement (closed) W 6 EW/ H 6 45 EH-117 W 4 SW-165 H 2 SH-165 W 2 SW -165 H 4 SH Spacing profile w/o clip-on system H 1 SH-15 Sash 13 Cover profile (sash) H 1 SH+13 H 2 SH-2 14 Center sealing bead 15 Glazing bead* H 1 SH+15 (incl ) e.g H 1 SH-2 W 6 SW-158 H 6 SH-158 Abbreviations: Symbols: EW= Element width *= not included in kit SW = Sash width = needs to be ordered separately SH= Sash height 45 = mitre cutting! Please note! All details specified are theoretical in nature and do not take into account any welding allowances. All details are given without any express or implied warranty whatsoever! 4.16 Material

92 Subtraction dimensions, Variant, Plan C Item Figure Designation Art.- No. Insert W=Width H=Height Quantity Subtraction dimensions Variant, Plan C (in mm) 16 Threshold W 1 EW (Element Width) 17 Cap profile W 1 SW Threshold cover, external W 1 2 x SW Running rail, internal W 1 EW-117 Threshold 20 Spacing profile W 2 EW Sealing profile, running rail W 1 EW Threshold cover, internal W 1 SW-81 Accessories 23 Sealing set, frame BSZ connector set Sealing set, sash Accessories set, sash Accessories set, seal Sealing set Plan C, F ! Please note! All details specified are theoretical in nature and do not take into account any welding allowances. All details are given without any express or implied warranty whatsoever! Material 4.17

93 Subtraction dimensions, Plan D Item Figure Designation Art.- No. 1 Frame profile Insert W=Width H=Height Quantity Subtraction dimensions Plan D (in mm) W 1 EW (Element Width) H 2 EH Frame reinforcement Spacing profile w. clip-on system W 1 EW (Element Width) H 2 EH-100 H 1 SH+17 H 1 SH+17 Frame 4 Guide profile W 2 EW Aluminum guide profile W 2 EW Cover profile (frame) W 2 SW Sash profile Reinforcement (closed) W 45 4 EW/2-17 H 45 4 H-117 W 4 SW- 165 H 4 SH Cover profile (sash) H 2 SH-2 Sash 11 Center sealing bead H 2 SH-2 12 Glazing bead* e.g W 4 SW-158 H 4 SH-158 Abbreviations: Symbols: EW= Element width *= not included in kit SW = Sash width = needs to be ordered separately SH= Sash height 45 = mitre cutting! Please note! All details specified are theoretical in nature and do not take into account any welding allowances. All details are given without any express or implied warranty whatsoever! 4.18 Material

94 Subtraction dimensions, Plan D Item Figure Designation Art.- No. Insert W=Width H=Height Quantity Subtraction dimensions Plan D (in mm) 13 Threshold W 1 EW (Element Width) 14 Cap profile W 1 EW-117** 15 Running rail, internal W 1 EW Running rail, external W 1 EW-117 Threshold 17 Sealing profile, running rail W 1 EW Threshold cover, internal W 2 SW-81 Accessories 19 Sealing set, frame BSZ connector set Accessories set, sash Accessories set, seal Sealing set, plan D, F **without consideration of drainage bridge ! Please note! All details specified are theoretical in nature and do not take into account any welding allowances. All details are given without any express or implied warranty whatsoever! Material 4.19

95 Subtraction dimensions, Plan F Item Figure Designation Art.- No. 1 Frame profile Insert W=Width H=Height Quantity Subtraction dimensions Plan F (in mm) W 1 EW (Element Width) H 2 EH Frame reinforcement Spacing profile w. clip-on system W 1 EW (Element Width) H 2 EH H 2 SH+17 Frame 4 Guide profile W 2 EW Aluminum guide profile W 2 EW Cover profile (frame) W 2 SW W 1 2x SW Sash profile Reinforcement (closed) W 45 8 EW/4+11 H 45 8 H-117 W 8 SW- 165 H 8 SH Spacing profile w/o clip-on system H 1 SH-15 Sash 10 Cover profile (sash) H 4 SH-2 11 Center sealing bead H 4 SH-2 12 Glazing bead* e.g W 8 SW-158 H 8 SH-158 Abbreviations: Symbols: EW= Element width *= not included in kit SW = Sash width = needs to be ordered separately SH= Sash height 45 = mitre cutting! Please note! All details specified are theoretical in nature and do not take into account any welding allowances. All details are given without any express or implied warranty whatsoever! 4.20 Material

96 Subtraction dimensions, Plan F Item Figure Designation Art.- No. Insert W=Width H=Height Quantity Subtraction dimensions Plan F (in mm) 13 Threshold W 1 EW (Element Width) 14 Cap profile* W 1 EW-134** 15 Running rail, internal W 1 EW Running rail, external W 1 EW-134 Threshold 17 Sealing profile, running rail W 1 EW Threshold cover, internal W 2 SW-81 W 1 2 x SW-174 Accessories 19 Sealing set, frame BSZ connector set Accessories set, sash Accessories set, seal Sealing set Plan C, F Sealing set, plan D, F **without consideration of drainage bridge ! Please note! All details specified are theoretical in nature and do not take into account any welding allowances. All details are given without any express or implied warranty whatsoever! Material 4.21

97 Cut-out dimensions/finished dimensions Plan A Subtraction dimensions, Plan A X W H Figure Insert W=Width H=Height Quantity Subtraction dimensions Plan A (in mm) Finished dimensions please enter: Frame profile incl. reinforcement W 1 EW (Element Width) H 2 EH-100 Spacing profile w. clip-on system W 1 SW+2 H 2 SH+17 Guide profile W 1 EW-100 Aluminum guide profile W 1 EW-100 Hingeing profile W 1 SW-85 Cover profile, frame, W 1 SW-60 4 Cover profile, frame, W 1 SW-68 Sash dimension X Sash profile W 4 W/2-17 H 4 EH-117 Reinforcement (C profile) (closed) FAM-165 Cover profile, sash, H 1 (FS) SH+13 H 2 (SS)) SH-2 (punched) Center sealing bead H 1 SH+15 (FS) H 1 SH-2 (SS) Glazing bead e.g W 4 SW-158 Threshold H 4 SW-158 W 1 EW (Element Width) Cap profile Threshold cover, external Running rail, internal Sealing profile, running rail Threshold cover, internal W 1 SW-16 W 2 SW-87 W 1 EW-117 W 1 EW-112 W 1 SW Material

98 Cut-out dimensions/finished dimensions Plan K Subtraction dimensions Plan K X W H Figure Insert W=Width H=Height Quantity Subtraction dimensions Plan K (in mm) Finished dimensions please enter: Frame profile incl. reinforcement Spacing profile w. clip-on system W 1 EW (Element Width) H 2 EH-100 W 1 SW-26 H 2 SH+17 Guide profile W 1 EW-100 Aluminum guide profile W 1 EW-100 Hingeing profile W 2 SW-200 Cover profile, frame, W 1 SW-170 Cover profile, frame, W 2 SW-68 Sash dimension X 4 Sash profile W 6 W/3+21 H 6 EH-117 Reinforcement (C profile) (closed) FAM-165 Cover profile, sash, H 2 (FS) SH+13 H 2 (SS)) SH-2 (punched) Center sealing bead H 2 SH+15 (FS) H 2 SH-2 (SS) Glazing bead e.g W 6 SW-158 H 6 SW-158 Threshold W 1 EW (Element Width) Cap profile Threshold cover, external Running rail, internal Sealing profile, running rail Threshold cover, internal W 1 SW-28 W 2 SW-87 W 1 EW-134 W 1 EW-129 W 1 SW-192 Material 4.23

99 Cut-out dimensions/finished dimensions Plan C Subtraction dimensions, Plan C X W H Figure Insert W=Width H=Height Quantity Subtraction dimensions Plan C (in mm) Finished dimensions please enter: Frame profile incl. reinforcement W 1 EW (Element Width) H 2 EH-100 Spacing profile w. clip-on system W 2 SW+2 H 2 SH+17 Guide profile W 1 EW-100 Aluminum guide profile W 1 EW-100 Hingeing profile W 1 2 x SW-182 Cover profile, frame, W 2 SW-60 Cover profile, frame, W 1 2 x SW Sash dimensions Sash profile W 8 SW-W/4+11 X H 8 EH-117 Reinforcement (C profile) (closed) FAM-165 Spacing profile w/o clip-on system H 1 SH-15 Cover profile, sash, H 2 (FS) SH+13 H 2 (SS)) SH-2 (punched) Center sealing bead (incl ) H 2 SH+15 (FS) H 2 SH-2 (SS) Glazing bead e.g W 8 SW-158 Threshold Cap profile Threshold cover, external Running rail, internal Sealing profile, running rail Threshold cover, internal H 8 SH-158 W 1 EW (Element Width) W 1 SW-16 W 1 2 x SW-186 W 1 EW-100 W 1 EW-95 W 2 SW-81! Please note! All details specified are theoretical in nature and do not take into account any welding allowances. All details are given without any express or implied warranty whatsoever! 4.24 Material

100 Cut-out dimensions/finished dimensions, Variant, Plan C Subtraction dimensions, Variant, Plan C W X H Figure Insert W=Width H=Height Quantity Subtraction dimensions, Variant, Plan C (in mm) Finished dimensions please enter: Frame profile incl. reinforcement W 1 EW (Element Width) H 2 EH-100 Spacing profile w. clip-on system W 1 SW + 2 H 2 SH + 17 Guide profile W 1 EW-100 Aluminum guide profile W 1 EW-100 Hingeing profile W 1 (2 x SW)-67 Cover profile, frame, W 1 SW-60 Cover profile, frame, W 1 (2 x SW) - 50 Sash dimensions X Sash profile W 6 EW/ H 6 EH-117 Reinforcement (C profile) (closed) FAM-165 Spacing profile w/o clip-on system H 1 SH-15 Cover profile, sash, H 1 (FS) SH+13 H 2 (SS)) SH-2 (punched) Center sealing bead H 1 SH+15 (FS) H 1 SH-2 (SS) E.g. glazing bead* W 6 SW-158 H 6 SW-158 Threshold W 1 EW (Element Width) Cap profile Threshold cover, external Running rail, internal W 1 SW-16 W 1 (2 x SW)-69 W 1 EW-117! Please note! All details specified are theoretical in nature and do not take into account any welding allowances. All details are given without any express or implied warranty whatsoever! Material 4.25

101 Cut-out dimensions/finished dimensions, Variant, Plan C Subtraction dimensions, Plan C, Variant Figure Insert W=Width H=Height Quantity Subtraction dimensions, Variant, Plan C (in mm) Finished dimensions please enter: Spacing profile W 2 EW-50 Sealing profile, running rail W 1 EW-12 Threshold cover, internal W 2 SW-81! Please note! All details specified are theoretical in nature and do not take into account any welding allowances. All details are given without any express or implied warranty whatsoever! Material

102 Cut-out dimensions/finished dimensions Plan D Subtraction dimensions, Plan D X W H Figure Insert W=Width H=Height Quantity Subtraction dimensions Plan D (in mm) Finished dimensions please enter: Frame profile incl. reinforcement W 1 EW (Element Width) H 2 EH-100 Spacing profile w. clip-on system H 2 SH+17 Guide profile W 2 EW-100 Aluminum guide profile W 2 EW-100 Cover profile, frame, W 2 SW-70 Sash dimension X Sash profile W 4 EW/2-17 H 4 EH (closed) W 4 FAM-165 H 4 4 Cover profile, sash, H 1 (FS) SH-2 H 1 (SS)) SH-2 Center sealing bead H 2 SH-2 E.g. glazing bead* W 4 SW-158 H 4 SH-158 Threshold Cap profile Aluminum running rail, external Sealing profile, running rail Running rail, internal Threshold cover, internal W 1 EW (Element Width) W 1 EW-117 W 1 EW-117 W 1 EW-112 W 1 EW-117 W 2 SW-81! Please note! All details specified are theoretical in nature and do not take into account any welding allowances. All details are given without any express or implied warranty whatsoever! Material 4.27

103 Cut-out dimensions/finished dimensions Plan F Subtraction dimensions, Plan F X W H Figure Insert W=Width H=Height Quantity Subtraction dimensions Plan F (in mm) Finished dimensions please enter: Frame profile incl. reinforcement W 1 EW (Element Width) H 2 EH-100 Spacing profile w. clip-on system H 2 SH + 17 Guide profile W 2 EW-100 Aluminum guide profile W 2 EW-100 Cover profile, frame, W 2 SW-70 W 1 2 x SW-150 Sash dimension X 4 Sash profile W 8 EW/4+11 H 8 EH (closed) W 8 H 8 FAM-165 Spacing profile w/o clip-on system Cover profile, sash, Center sealing bead H 1 SH-15 H 4 SH-2 (punched) H 4 SH-2 E.g. glazing bead* W 8 SW-158 H 8 SH-158 Threshold Cap profile Sealing profile, running rail Running rail, internal Running rail, external W 1 EW (Element Width) W 1 SW-134 W 1 EW-95 W 1 EW-100 W 1 EW-134 Threshold cover, internal W 2 SW-81 W 1 2 x SW Material

104 Kits, frame sets Frame sets, Plan A VEKASLIDE Frame set, size 30/ Designation Article no. metre metre Frame profile bar bar 4.45 VEKASLIDE Frame set, size 30/ bar bar 5.25 Frame reinforcement bar bar bar bar 5.25 Spacing profile w. clip-on system bar 5.25 (unilaterally punched) 1 bar 1.80 Guide profile bar bar 3.40 Aluminum guide profile bar bar 3.40 Hingeing profile bar bar 1.80 Cover profile, frame bar bar 1.80 Cover strip bar bar 1.80 Sealing set, frame comprising: , 2 pcs , 2 pcs , 1 x left, 1 x right , 1 x left, 1 x right , 1 x left, 1 x right , 2 pcs. 1 bar 5.25 (unilaterally punched) 1 bar 1.80 comprising: , 2 pcs , 2 pcs , 1 x left, 1 x right , 1 x left, 1 x right , 1 x left, 1 x right , 2 pcs. 4 Threshold-frameconnector incl. sealing plates comprising: , 2 x , 2 x , 2 x comprising: , 2 x , 2 x , 2 x i Info All kits refer to Plan A. Material 4.29

105 Kits, frame sets Frame sets, Plan A VEKASLIDE frame set, Size 35/ Designation Article no. metre metre Frame profile bar bar 4.45 VEKASLIDE frame set Size 35/ bar bar 5.25 Frame reinforcement bar bar bar bar Spacing profile w. clip-on system bar 5.25 (unilaterally punched) 1 bar 1.80 Guide profile bar bar 3.40 Aluminum guide profile bar bar 3.40 Hingeing profile bar bar 1.80 Cover profile, frame bar bar 1.80 Cover strip bar bar 1.80 Sealing set, frame comprising: , 2 pcs , 2 pcs , 1 x left, 1 x right , 1 x left, 1 x right , 1 x left, 1 x right , 2 pcs. 1 bar 5.25 (unilaterally punched) 1 bar 1.80 comprising: , 2 pcs , 2 pcs , 1 x left, 1 x right , 1 x left, 1 x right , 1 x left, 1 x right , 2 pcs. Threshold-frame-connector incl. sealng plates comprising: , 2 x , 2 x , 2 x comprising: , 2 x , 2 x , 2 x i Info All kits refer to Plan A Material

106 Kits, frame sets Frame sets, Plan A VEKASLIDE Frame set, Size 40/ Designation Article no. metre metre Frame profile bar bar 4.02 VEKASLIDE Frame set, Size 40/ bar bar 4.02 Frame reinforcement bar bar bar bar 5.25 Spacing profile w. clip-on system bar 5.25 (unilaterally punched) 1 bar 2.52 Guide profile bar bar 4.90 Aluminum guide profile bar bar 4.90 Hingeing profile bar bar 2.52 Cover profile, frame bar bar 2.52 Cover strip bar bar 2.52 Sealing set, frame comprising: , 2 pcs , 2 pcs , 1 x left, 1 x right , 1 x left, 1 x right , 1 x left, 1 x right , 2 pcs. 1 bar 5.25 (unilaterally punched) 1 bar 2.52 comprising: , 2 pcs , 2 pcs , 1 x left, 1 x right , 1 x left, 1 x right , 1 x left, 1 x right , 2 pcs. 4 Threshold-frame-connector incl. sealng plates comprising: , 2 x , 2 x , 2 x comprising: , 2 x , 2 x , 2 x i Info All kits refer to Plan A. Material 4.31

107 Kits, frame sets Frame sets, Plan A VEKASLIDE Frame set, Size 50/ VEKASLIDE Frame set 50/ Designation Article no. metre metre Frame profile bar bar bar bar 5.25 Frame reinforcement bar bar bar bar Spacing profile w. clip-on system bar 5.25 (unilaterally punched) 1 bar 2.52 Guide profile bar bar 4.90 Aluminum guide profile bar bar 4.90 Hingeing profile bar bar 2.52 Cover profile, frame bar bar 2.52 Cover strip bar bar 2.52 Sealing set, frame comprising: , 2 pcs , 2 pcs , 1 x left, 1 x right , 1 x left, 1 x right , 1 x left, 1 x right , 2 pcs. 1 bar 5.25 (1-side punched 1 bar 2.52 comprising: , 2 pcs , 2 pcs , 1 x left, 1 x right , 1 x left, 1 x right , 1 x left, 1 x right , 2 pcs. Threshold-frame-connector incl. sealng plates comprising: , 2 x , 2 x , 2 x comprising: , 2 x , 2 x , 2 x i Info All kits refer to Plan A Material

108 Kits, Sash sets Sash sets, Plan A VEKASLIDE Sash set, Size 30/ VEKASLIDE Sash set, Size 30/ Designation Article no. metre metre Sash profile bar bars bar bars 5.25 Sash reinforcement Fixed sash bar bar bar bar 2.40 Sash reinforcement Sliding sash bar bar bar bars 2.40 Cover profile, sash bar 5.25 (punched on 2 sides) Center sealing bead bar bar 5.25 Accessories set, sash (for 1 FS + 1 SS) Hardware comprising: , 11 pcs pcs , 19 pcs , 22 pcs. 1 bar 5.25 (punched on 2 sides) comprising: , 11 pcs pcs , 19 pcs , 22 pcs. 4 Sealing set, sash comprising: , 1 pc , 1 x left, 1 x right , 1 pc , 1 pc , 1 pc. comprising: , 1 pc , 1 x left, 1 x right , 1 pc , 1 pc , 1 pc. i Info All kits refer to Plan. The kits do not include glazing beads. A summary overview of glazing beads is shown in Chapter 6 "Glazing/Assembly". Material 4.33

109 Kits, Sash sets Sash sets, Plan A VEKASLIDE Sash set, Size 35/ VEKASLIDE Sash set, Size 35/ Designation Article no. metre metre Sash profile bars bars bars bars 5.25 Sash reinforcement Fixed sash bar bar bar bar 2.40 Sash reinforcement Sliding sash bar bar bar bars Cover profile, sash bar 5.25 (punched on 2 sides) Center sealing bead bar bar 5.25 Accessories set, sash (for 1 FS + 1 SS) Hardware comprising: , 11 pcs pcs , 19 pcs , 22 pcs. 1 bar 5.25 (punched on 2 sides) comprising: , 11 pcs pcs , 19 pcs , 22 pcs. Sealing set, sash comprising: , 1 pc , 1 x left, 1 x right , 1 pc , 1 pc , 1 pc. comprising: , 1 pc , 1 x left, 1 x right , 1 pc , 1 pc , 1 pc. i Info All kits refer to Plan. The kits do not include glazing beads. A summary overview of glazing beads is shown in Chapter 6 "Glazing/Assembly" Material

110 Kits, sash sets Sash sets, Plan A VEKASLIDE Sash set, Size 40/ VEKASLIDE Sash set, Size 40/ Designation Article no. metre metre Sash profile bars bars bars bars 5.25 Sash reinforcement Fixed sash bars bar bar 2.40 Sash reinforcement Sliding sash bar bar bar bars 2.40 Cover profile, sash bar 5.25 (punched on 2 sides) Center sealing bead bar bar 5.25 Accessories set, sash (for 1 FS + 1 SS) Hardware comprising: , 11 pcs pcs , 19 pcs , 22 pcs. Sealing set, sash comprising: , 1 pc , 1 x left, 1 x right , 1 pc , 1 pc , 1 pc. 1 bar 5.25 (punched on 2 sides) comprising: , 11 pcs pcs , 19 pcs , 22 pcs. comprising: , 1 pc , 1 x left, 1 x right , 1 pc , 1 pc , 1 pc. 4 i Info All kits refer to Plan. The kits do not include glazing beads. A summary overview of glazing beads is shown in Chapter 6 "Glazing/Assembly". Material 4.35

111 Kits, Sash sets Sash sets, Plan A VEKASLIDE Sash set, Size 50/ VEKASLIDE Sash set, Size 50/ Designation Article no. metre metre Sash profile bars bars bars 5.25 Sash reinforcement Fixed sash bar bars bars 2.40 Sash reinforcement Sliding sash bars bar bars Cover profile, sash bar 5.25 (punched on 2 sides) Center sealing bead bar bar 5.25 Accessories set, sash (for 1 FS + 1 SS) Hardware comprising: , 11 pcs pcs , 19 pcs , 22 pcs. Sealing set, sash comprising: , 1 pc , 1 x left, 1 x right , 1 pc , 1 pc , 1 pc. 1 bar 5.25 (punched on 2 sides) comprising: , 11 pcs pcs , 19 pcs , 22 pcs. comprising: , 1 pc , 1 x left, 1 x right , 1 pc , 1 pc , 1 pc. i Info All kits refer to Plan. The kits do not include glazing beads. A summary overview of glazing beads is shown in Chapter 6 "Glazing/Assembly" Material

112 Kits, threshold sets Threshold sets, Plan A Exotherm 1.5 Threshold 3000 mm, Size 30, Exotherm 1.5 Threshold 3500 mm, Size 35, Designation Threshold Exotherm 1.5 (base) Article no. Quantity metre metre Quantity plus additional profiles Threshold sets, Plan A Exotherm 1.5 Threshold 4000 mm, Size 40, Exotherm 1.5 Threshold 5000 mm, Size 50, Designation Threshold Exotherm 1.5 (base) Article no. Quantity metre metre Quantity plus additional profiles i Info All kits refer to Plan A. Material 4.37

113 Kits, threshold sets Threshold sets, Plan A Exotherm 1.5 Threshold mm, Size Designation Threshold Exotherm 1.5 (base) comprising: plus Article no. additional profiles 104, Quantity metre i Info Alternatively, the threshold G.U-thermostep by G-U Gretsch Unitas may be used. Additional article Designation Article no. metre HST (lift/slide door) all plans Sealing set x , Size 30/35 i Info Sealing set must always be ordered separately! HST (lift/slide door) all plans, optional comprising: x Weather sides or , Size 40/ x , Size x HST (lift/slide door) Plan D + F HST (lift/slide door) Plan C Aluminum running rail, external Threshold cover, external or HST (lift/slide door) Plan C + F i Info Sealing set. This must be ordered additionally! Sealing set comprising: HST (lift/slide door) Plan D + F Sealing set comprising: i Info All kits refer to Plan A Material

114 Fittings sets VEKASLIDE Fittings sets, Plan A VEKASLIDE Fittings set 2.30 m, Size 30/35/40, VEKASLIDE Fittings set 2.30 m, Size 50, VEKASLIDE Fittings set 2.30 m, Size 65, comprising: Lever Carriage Gear, Size 220 Connection rod, size 200 Design: EV1 silver comprising: Lever Carriage Gear, Size 220 Connection rod, Size 250 Design: EV1 silver comprising: Lever Carriage Gear, Size 220 Connection rod, Size 335 Design: EV1 silver Fittings Accessories Set of latch parts Plan C + F Corner guide for Plan C + F Gear extension Two-sided handle set, silver Additional carriage comprising: comprising: comprising: comprising: comprising: latch part, bottom Countersunk bolt Pan-head tapping screw Corner guide Gear extension with bolt Outside handle, 1 pc. PZ rosettes, 2 pcs. Carriage, 1 pc. incl. 4 setscrews i Info All kits refer to Plan A. Material 4.39

115 Material

116 Processing/Assembly Position of profiles Sash 5.4 Before cutting out Cut out sash Manufacture sash Frame profile 5.6 Cut out frame and additional profiles Prepare frame Fit connector to threshold Connect frame Additional profiles / accessories 5.10 Fit additional profiles Prepare fixed sash Prepare sliding sash Assembly 5.16 Fit fixed sash Fit sealing parts and threshold profiles Fit sliding sash Annex: Processing 5.20 Steel reinforcements for all plans Draining and ventilating Fittings milling Process T-profiles Additional work - other plans Additional work for RC

117 Position of the profiles Plan A Fixed sash Sliding sash Usage, processing

118 Position of profiles i Info The figure shows an overview of the positions of the profiles for Plan A. Detailed instructions for constructing the lift/slide door, in particular the positioning of the sealing parts, are provided on the following pages. No. Profile Article no. Quantity 1 Frame profile (height) (105,330) 1 x 2 Frame profile (height) (105,330) 1 x 3 Frame profile (width) (105,330) 1 x 4 Spacing profile w. clip-on system, punched out on 1 side (105,331) 1 x 5 Spacing profile w. clip-on system, 1-side mitred (105,331) 1 x 6 Spacing profile w. clip-on system, 1-side mitred (105,331) 1 x 7 Guide profile (105,332) 1 x 8 Aluminum guide profile (104,238) 1 x 9 Hingeing profile (105,335) 1 x 10 Cover profile, frame (105,336) 1 x 11 Cover profile, frame (109,495) 1 x 12 Cover profile, sash (105,333) 1 x 13 Cover profile, sash (105,333) 1 x 14 Center sealing bead (105,334) 1 x 15 Center sealing bead (105,334) 1 x 16 Threshold (104,430) 1 x 17 Cap profile (104,433) 1 x 18 Threshold cover, external (104,437) 1 x 19 Running rail, internal (104,438) 1 x 20 Sealing profile, running rail (104,443) 1 x 21 Threshold cover, internal (104,444) 1 x 5 Usage, processing 5.3

119 Sash Before cutting out! Please note! In the following the processing of a lift/slide door in a Plan A design will be described. Please note that when processing other plans, or for the WK2 design, additional work is required. These work tasks are explained in the Annex to this chapter. The sequence of the work steps described here only serves as an example. You may possibly have to adapt the sequence of steps to the actual conditions. For each plan, the chapter "Material" contains a list of the material required as well as the subtraction dimensions. When cutting out the sash profiles please note that the welding allowances have not yet been taken into consideration in the lists. Also, pay attention to mitred cuts or punching that need to be carried out with some profiles. This is appropriately marked in the cutting lists. Legend = material required = working steps = tool required Cut out sash 5 Sash profile ( ) Steel reinforcement ( ) Steel reinforcement ( ) Steel reinforcements Depending on the plan, the lift/slide door features one or several sliding sashes (SS). For sliding sashes only the closed steel reinforcement ( ) is used. With the exception of the center area, the C profile ( ) is used as a steel reinforcement for fixed sashes. Which steel reinforcements are used for plan A is shown in the figure below. The figures for the other diagrams are shown in the Annex to this chapter under "Steel reinforcements for all diagrams". Plan A Reinforcement closed Reinforcement (C profile) 5.4 Usage, processing

120 Sash Manufacture sash! Please note! Before welding the sash profiles, ensure that the steels have been correctly allocated. Always use welding fillers as otherwise the profiles may deform. A milling of the steel reinforcement within the area of the transmission (Gauge 27.5 mm) or the carriage is not necessary. Execute the mounting holes for the fixed sash on the loose rod or on the finished fixed sash. Carry out all milling and drilling work before welding! (Figures for drainage/ventilation are shown under "Milling and Drilling" in the Annex to this chapter). When bonding PVC with rubber, the assembly adhesive Aquaflex by WEICON is used. Sash profile ( ) Steel reinforcement ( ) Steel reinforcement ( ) 1. Drain sash profile ( ) (front or bottom). 2. Vent sash profile ( ). 3. Insert steel reinforcement ( ) and bolt on. 4. Insert steel reinforcement ( ) and bolt on. 5. Weld together sash profile ( ). 6. Dress sash profile ( ). Carefully dress all sash corners in order to ensure perfect functioning of the guide slides and the sash cover profile. 5 Carefully remove welding beads Usage, processing 5.5

121 Frame profile Cut out frame and additional profiles Frame profile ( ) Frame reinforcement ( ) Spacing profile ( ) Aluminum guide profile ( ) Cover profile (frame) ( ) Cover profile (sash) ( ) Glazing bead ( ) Cap profile ( ) Running rail, internal ( ) Threshold cover, internal ( ) Insulation wedge ( ) for threshold Guide profile ( ) Hingeing profile ( ) Cover profile (frame) ( ) Center sealing bead ( ) Threshold ( ) Threshold cover, external ( ) Sealing profile, running rail ( ) Insulation wedge ( ) for threshold Insulation wedge for frame reinforcement Optionally insert insulation wedges into threshold and frame Push in frame reinforcement ( ) and bolt in an offset fashion into the two external grooves. Optionally push in insulation wedge ( ). 2. Cut the same cutting lengths within a single work process as several profiles need to be cut to the same length. Insulation wedges and Insulation wedge Usage, processing

122 Prepare frame Frame profile 1 x threshold ( ) Ø 5.0 mm drill Ø 6.5 mm drill 1 x upper frame profile ( ) Ø 12 mm drill BSZ drilling template ( ) Counterbore 1. Use drilling template to drill mounting holes into threshold ( ) (4 x Ø 6.5 mm). Drilling template on threshold (Step 1) Bores in threshold (Step 1) 2. Use drilling template to drill holes into top frame ( ) (4 x Ø 6.5 mm; 4 x Ø 5.0 mm). 3. Bore top of the frame ( ) (4 x Ø 12 mm). 4. Counterbore boreholes. 5 Drilling template on frame (Step 2) Bores frame (Steps 3 and 4) Ø5 Ø Ø12 Ø (100) Ø6.5 Ø6.5 Drilling pattern, frame Bores, frame Usage, processing 5.7

123 Frame profile Fit connector to threshold 2 x BSZ connector set ( ) 1 x threshold ( ) 1. Place bottom sealing plates ( ) on threshold profile ( ). 2. Push on BSZ connector ( ) and bolt on with FB bolt (not included within scope of delivery) with a length of at least 25 mm. 3. Place top sealing plates ( ) in position BSZ connector Usage, processing

124 Frame profile Connect frame! Please note! Before bolting down the frame: Define the slide direction of the sashes! The frame is fitted in a horizontal position. For bolting down the top frame, countersunk bolts with a minimum length of 100 mm are required (not included within scope of delivery). Connection profiles such as the adapter profile , balcony connection profiles or widenings should best be fitted directly after the frame has been bolted down. 1 x threshold ( ) 1 x Accessories set, sash ( ) 3 x frame profiles ( ) Optional: 4 x countersunk bores (Ø 6 x 100 mm) Ensure that the grooves in the side frames are in their correct position! Plan A Plan A Frame, inside Frame, inside Frame, inside Frame, inside Position of the grooves, using the example of Plan A: Perspective = room-side; red line = position of the groove. 5 Position of the grooves depending of the sliding direction 1. Bolt threshold ( ) onto side frame profiles ( ). 2. Bolt upper frame ( ) onto side frame profiles. The external bolting of the upper onto the side frames (Ø 6 x 100) is optional in order to ensure that the surfaces are even. Frame mounting Usage, processing 5.9

125 Additional profiles / accessories Fit additional profiles (frame/threshold) 2 x spacing profile FS ( , 1-side mitred cut) 1 x spacing profile SS ( , 1-side punched) 1 x cover profile ( ) 1 x Guide profile ( ) Ø 3.2 mm drill 1 x spacing profile SS ( , 1-side punched) 1 x aluminum guide profile ( ) 1 x Sealing set, frame ( ) 1 x Sealing set, sash ( ) 1. Clip on top guide profile ( ) to the inner side of the frame and secure by means of bolts. 2. Clip aluminum guide profile ( ) onto guide profile ( ). 3. Clip spacing profile ( , 1-side punched) onto side frame (SS). 4. Place sealing part ( ) onto the bottom of the spacing profile ( , single side mitred cut). Thereafter clip spacing profile into side frame (FS). 5 Sealing part Spacing profile with sealing part Glue sealing part ( ) onto spacing profile FS ( , 1-side mitred cut) on the mitred cut. Then clip spacing profile into the top of the frame (FS). Spacing profile with sealing part Spacing profile ( ) clipped into the top of the frame 6. Use a knife to remove a sealing plate protruding inwards from the sealing part ( ) Usage, processing

126 Additional profiles / accessories Use a knife to remove protrusion (broken line) 7. Clip on cover profile ( ) in the top frame within the area of the sliding sash. Cover profile The frame can now be set up. If necessary, use a plate as an assembly aid. 5 Usage, processing 5.11

127 Assembly Prepare fixed sash i Info The nipple head screws ( ) from the accessories set have a length of 8 mm. The holes for the nipple head screws can be pre-drilled. The position of the center sealing bead ( ) can be shifted by 2 mm to the left or right in order to compensate for tolerances. The sealing sets for sashes and frames contain some sealing parts in right-handed and left-handed versions that are inserted in accordance with the sliding direction of the sashes. In such cases, there will always be one part that is left over. 1 x Cap profile ( ) 1 x Accessories set, sash ( ) 1 x Sealing set ( ) 1 x Sealing set, frame ( ) 1. Fit and glue in sealing part ( ) at the bottom of the fixed sash (flush, see red marking in the figure). 2. Clip on spacer ( ). Ensure that the spacers are correctly positioned. The spacers must be positioned exactly above the mounting holes for sash/frame connection (max. distance of the spacers: 700 mm). 5 Sealing part bottom of the fixed sash glue on such that it is flush (red marking) Position of the sealing part at the Clip on spacer ( ) Arrangement of spacers 3. Apply sash seal ( ). In the lower corner area undercut seals and glue onto sash. 4. Clip cap profile ( ) onto spacer ( ) on the underside of the fixed sash Usage, processing

128 Assembly Cap profile Screw on nipple head screw ( ) for center sealing bead with a distance of 19 mm from the outside edge. 19 Distance of 19 mm from the outside edge 5 Usage, processing 5.13

129 Assembly Prepare sliding sash! Please note! Please observe the processing instructions provided by the fittings manufacturers, in particular the subtraction dimensions for the gear system (termination with guide slide) Subtraction dimensions for gear 1 x center sealing bead ( ) 1 x Accessories set, sash ( ) 1 x Fittings set ( ) Assembly adhesive 1. Set bore for operating lever. 2. Fit carriage, gear and other fittings. 1 x Sealing set ( ) 1 x Sealing set, frame ( ) Accessories set, sash ( ) Laterally clip on the guide slides 1. Clip the two guide slides ( ) into the top of the sliding sash. 2. Set nipple head screw ( ) Usage, processing

130 Assembly 3. Next apply assembly glue to center sealing bead ( ) and fit flush with lower edge of sash. Apply assembly glue (marked in red) 4. Position and glue on sealing part ( ) at the bottom of the center sealing bead. Sealing part Sealing part glued to center sealing bead 5. Apply seal ( ) to sash. Allow seal to run up to the center sealing bead. In the lower corner area undercut the seals and glue onto sash. 5 Usage, processing 5.15

131 Assembly Fit fixed sash! Please note! As sealing parts still need to be positioned, bolting into the top frame center will only be carried out at the end! 1 x center sealing bead ( ) 1 x Cover profile, sash ( ) 1 x Threshold cover, outside ( ) 1 x Threshold cover, internal ( ) 1 x Sealing profile ( ) 1 x Running rail, internal ( ) 1 x Sealing set ( ) 1 x Sealing set, frame ( ) 1 x Sealing set, sash ( ) 1 x Accessories set, sash ( ) 1. Hook fixed sash ( ) into frame and position. 2. Clip end cap ( ) onto cover profile, sash ( ). 3. Clip cover profile, sash ( ), onto fixed sash. The longer side of the profile always points to the center sealing strip! 5 End cap End cap on the cover profile 4. Bolt sash and frame together using oval head screws ( ) Cover profile with sealing part on sash 5. Position sealing part ( , left or right) on threshold, screw in and push into the fixed sash until the stop position is reached (see red marking in figure). Lift sealing part ( ), apply assembly adhesive to the 5.16 Usage, processing

132 Assembly underside of the short half and glue on. Sealing part Insert sealing part to the left Push in until the stop position is reached (stop position marked in red) Apply assembly glue on underside (red) and bond together 6. Clip center sealing bead onto clamping nipple. 7. Glue sealing part ( ) at the top and flush onto the center sealing bead of the fixed sash. 5 Sealing part ( ) on center sealing bead 8. Apply seal ( ) to stop profile ( ). 9. Glue sealing part ( ) onto stop profile ( ). 10. Clip stop profile ( ) centrally into the top frame within the sliding sash area. Sealing part Stop profile clipped into the top of the frame Fit sealing parts and threshold profiles Usage, processing 5.17

133 Assembly 11. Glue sealing part ( ) into the outside corner between stop profile and spacing profile (sliding sash). Sealing part self-adhesive Sealing part in top corner of the frame 12. Glue sealing plug ( ) on the inside against the spacing profile. 13. Glue sealing part ( ) onto the sealing plug ( ). 5 Sealing plug Sealing part glued onto sealing plug Place sealing profile ( ) in position. 15. Clip on running rail, internal ( ). Position of the sealing profile ( ) (lilac) Position of the running rail, internal ( ) (yellow) 16. Use hammer with care to fit threshold cover, external ( ) to threshold. 17. Clip threshold cover, internal ( ) onto cap profile ( ). 18. Screw sash centrally into the top frame. Fit sliding sash 5.18 Usage, processing

134 Assembly Cover profile, sash punched out Cover profile, frame ( ) ( ) i Info Use drilling gauge to mark, drill and screw in closing bolt after the sliding sash has been hung on its hinges. If necessary, the stop buffers may optionally be attached on the sash or the frame (for assembly in older buildings screws can be concealed here). 1. Lift sliding sash above the threshold and fit into frame. 2. Cover profile / sash punched out ( ) - adapt to the guide profile at the top (pre-punching at the bottom) Sash top edge Sash bottom edge 3. Clip cover profile ( ) into sliding sash. The longer side of the strip always points toward the center sealing bead! doort profile ( ), pre-punching at the bottom Lift/slide door Plan A, sliding sash right (View on the room side) 4. Clip on cover profile ( ) in the top frame. This is now secured against being lifted out. Usage, processing 5.19

135 Annex - Steel reinforcements Steel reinforcements for all plans Reinforcement closed Reinforcement (C profile) Plan: A Plan: D 5 Plan:K Plan:K- 3 part HST (lift/slide door) with mullion Plan: C Variant, Plan: C Plan:F 5.20 Usage, processing

136 Annex - Drainage and ventilating Milling and drilling! Please note! Please read with care the following instructions on milling and drilling! Mark profile pieces immediately after cutting and place for further processing on transport carriages or transport conveyors. Carry out all milling and drilling work before welding! All milling can be carried out on the individual profile piece. Remove any chips and milling residues on the profile by blowing. This ensures among other things a clean eduction of water, optimum functionality of fittings and prevents any discoloration (metal chips) and scratches. These machines can be used as tools: Fitting mortising machine and special machines (adapted to the system) Milling machines for rational processing Small machines by various tool manufacturers. The following work processes occur: Steam pressure equalization apertures and front chamber ventilation for sashes Steam pressure equalization apertures for mullions Lock mortise milling and lock mortise drilling. Driving rain resistance In order to provide for a safe water drainage from the construction, pressure equalization apertures are an advantage. These are located in the area protected against driving rain and reduce the pressure difference between the rebate space and the outside climate. In this way, the constructions achieve higher outflow volumes and thus a higher driving rain resistance classification. The size and arrangement of the outlet apertures also plays a decisve role. Investigations at the ift Rosenheim have shown that bores with a diameter of less than 8 mm or elongated holes smaller than 5 x 20 mm are insufficient due to the surface tension of the water. Drainage via front chambers and via water slots located in laterally offset positions, however, does have a positive effect on the outflow of water. 5 Pressure equalization In order to avoid any heat accumulation in the case of non-white profiles, all outside (weather side) front chambers must be ventilated. The ventilation of front chambers only concerns those chambers that have not yet been opened by other milling operations. Usage, processing 5.21

137 Annex - Drainage and ventilating Pressure equalization Pressure equalization apertures in the top horizontal sash provide for a trouble free drainage of the sash rebate even for higher pressure differences. The inlet milling is designed as an elongated hole (5 x 30 mm). The number and arrangement of the inlet millings are found on page Pressure equalization apertures Steam pressure equalization The steam pressure equalization apertures in the sash and mullion rebates are to be designed as an elongated hole (5 x 30 mm). The number and arrangement of the inlet and outlet millings are shown on page Steam pressure equalization apertures Drainage to the front or bottom 54.5! Please note! If a sash is drained in a downward direction (bottom drainage) it may be necessary to use a long drill in order to open the front chamber completely! 5.22 Usage, processing

138 Annex - Drainage and ventilating Arrangement of milling cuts! Please note! In the case of non-white profiles all outside front chambers must be ventilated! Steam pressure equalization apertures 5 x 30 mm, 3 inlet millings, 2 outlet millings. From a sash width of 1600 mm, a third outlet milling must be made in a central position! Pressure equalization apertures 5 x 30 mm, 2 inlet millings! Pressure equalization apertures Steam pressure equalization apertures Usage, processing 5.23

139 Annex - Drainage and ventilating Front chamber ventilation for non-white profiles! Please note! The reinforcement chamber must not be opened as a result of this processing work! Front chamber ventilations are fitted at the top in transverse, right-hand and left-hand positions, with bores Ø 5 mm. The design can be effected as for position 1 or 2. In the center area of both sashes, see position 3, at the top one bore each with Ø 5 mm. Steam pressure equalization apertures Position 1 Position 2 5 Position Usage, processing

140 Annex - Fittings milling Fittings milling, gauge 27.5 mm For fittings milling on the loose rod, take into account a welding allowance (1005 mm + 3 mm =1008 mm up to bottom edge of sash)! Bottom milling only when using a profile cylinder! Attachment of the recessed handle (Milling 96 x 26 mm) by bolting together with the rotary handle! Profile cylinders on both sides: see fittings installation drawing Ø mm up to bottom edge of sash Gauge 27.5 mm Usage, processing 5.25

141 Annex - Fittings milling Fittings milling, gauge 37.5 mm For fittings milling on the loose rod, take into account a welding allowance (1005 mm + 3 mm =1008 mm up to bottom edge of sash)! Bottom milling only when using a profile cylinder! Attachment of the recessed handle (Milling 96 x 26 mm) by bolting together with the rotary handle! Profile cylinders on both sides: see fittings installation drawing Ø mm up to bottom edge of sash Gauge 37.5 mm Usage, processing

142 Annex - Processing T-profiles General information The VEKA profile systems offer various different attachment variants for the mechanical joining of T profiles. For each view width of the T profiles a special connector made of zinc diecast is available. An additional connection option is provided by the 2-component post connection. For a corresponding post geometry, there is the option to attach to the screw channels, but only when used vertically. For the contour millings of the T-profiles after cutting, the following pages show milling drawings for placing your tool orders.! Please note! Please read with care the following instructions on the processing of T-profiles (rebate post /mullions)! Always screw connectors into reinforced profiles! For the horizontal use of T profiles, additionally seal by means of a zinc diecast connection. When using 2-component post connectors, additionally consult assembly instructions. required accessories for VEKASLIDE Sash mullions Connector incl. sealing plate Fig. Milling Sealing plug, horizontal Drilling gauge , Page , , ,086 i Info The following information on the processing of T-profiles refers to standard profiles and not in particular to the lift/slide door. Usage, processing 5.27

143 Annex - Processing T-profiles Drilling and attachment 1. Use drilling template (Fig. 1) to pre-drill appropriate holes (Ø 3,2 mm) (Fig. 3). 2. Push connector over the armoured T-profile (Fig. 2) and connect by bolting on both sides. In the example shown here (Figs. 4 and 5), window construction screws with a diameter of Ø 3.9 x 19 mm (article no ) have been used. The screw length must be adapted to the geometry. 39mm mm 93mm mm 1 2 Drilling template Center axis Axis distance for T-profile 39 mm 64 mm 50 mm 75 mm mm 85 mm 70 mm 100 mm mm 118 mm (60) Screwing position Drilling position By a 1 mm offset, the T-profile draws itself into a flush position within the frame/sash Usage, processing

144 Annex - Processing T-profiles Sealing 1. In the case of a horizontal use of T-profiles with zinc diecast connectors, additional sealing must be provided for. Cut the armouring with a deduction of 15 mm on each side, and insert sealing plugs (EPDM caoutchouc) on both sides into the reinforced chamber (Fig. 2). 2. The additional sealing with silicone is carried out before fitting the connector (Fig. 3 left). 3. Additionally seal laterally the rebate posts/mullions with silicone (Fig. 3 right). 1 Sealing plug mm Subtraction dimension, reinforcing 3 Silicone Silicone Silicone Usage, processing 5.29

145 Annex - Processing T-profiles Milling drawing A Milling for post profiles inserted into welded frames. Milling for mullion profiles that are inserted into welded sash frames such that they are not flush with the surface and half surface offset. Milling for T profiles in the crosswork area R x "X" R Usage, processing

146 Notes 5 Usage, processing 5.31

147 Additional work, variant Plan C Additional work, variant Plan C 1. Cut and insert spacing profile ( ) Cutting dimensions for spacing profile top and bottom, horizontal, in the fixed sash Usage, processing

148 Additional work, variant Plan C i Info The steps 2-6 apply to variant, Plans C, D+F and C. 2. Leave open sash cover ( ) of the inside fixed sash on both sides. 3. Detach spacing profile ( ) at the top Sash top edge Sash bottom edge 5 Plan C, F + Variant Plan C, (sliding sash inside/lock area) Variant: Plan C Fixed sash, inside all plans sliding sash 4. Cut spacing profile ( ) and insert, see figure Screw latch bolt with spacing profile ( ) and cover profile, sash, ( ) into sash. 6. Insert sealing part ( ) and sealing part ( ) (not Plan D). Sealing part Sealing part Usage, processing 5.33

149 Additional work - Plan D and F Additional work - Plans D and F! Please note! For a sash width of 1.90 m, use 3 drainage bridges ( )! 1. Cut cap profile ( ). Schema D SS outside: SW + 3 SS inside: SW (for 2 x /30 mm per drainage bridge) (SW - 176) : 2 (for 3 x /30 mm per drainage bridge) Plan F SS outside: SW + 3 SS inside: SW (for 3 x /30 mm per drainage bridge) 2. Insert cap profile ( ) and drainage bridges ( ) into threshold ( ) and bolt on profile (SW bolt 4.3 x 25). 5 Mounting of cap profile Drainage bridge Clip running rail ( ) into cap profile ( ). FB-146 FB+3 Sash width up to 1.90 m 5.34 Usage, processing

150 Additional work - Plan D and F FB FB FB+3 Sash width > 1.90 m 4. Insert sealing pad ( ) centrally into the top frame (see drawing below for subtraction dimension for position). 5. Position sealing part at the bottom on the threshold (see drawing below for subtraction dimension for position). 6. Glue on sealing part ( ) in the center area of the threshold. 5 Sealing pad Sealing part The position of the sealing part is shown in the figure below. Sealing part Usage, processing 5.35

151 Additional work - Plan D and F SW+15 SW+3 SW+3 SW+15 Position of sealing part (marked in red), position of sealing part (marked in blue). 7. Cut sealing part ( ) to the dimension of the center sealing bead (23 mm) and glue on the outside sliding sash (Plans D + F). 5 Cut sealing part (red line) Glued onto the underside of the center sealing bead 8. Insert sash. 9. Insert cover profile, frame, ( ) into the top frame on both sides (2 x). Continue with Step 2-6 as Variant, Plan C see page Additional work, Plan C 1. Use the sealing parts from the sealing set, Plan C+ F ( ). 2. Continue with Step 2-6 as Variant, Plan C Usage, processing

152 Additional work for RC 2 Additional work for resistance class 2 (RC 2) Apply additional steel reinforcements in the sliding sash and center sealing bead Pre-milling of sash and reinforcement (gear with gauge 37.5 mm; protection against forced opening by drilling) Attach fittings Screw on center sealing bead Insert spacing parts (VEKAPLAN S) i Info RC 2 can be reached by means of 2 variants, see page 3.11 in the Chapter "Profile combinations. Center sealing beads ( ) Steel reinforcement (Variant 1) Screws Ø 4.8 x 40 mm Sash profile ( ) Steel reinforcement (Variant 2) VEKAPLAN S plate profile Apply steel reinforcements 1. Push in steel reinforcement ( ) into the upright sash profile of the sliding sash (Variant 1). 2. Push in steel reinforcement ( ) into all center sealing beads. Milling 1. Pre-mill sash and reinforcement for gauge 37.5, for milling drawing see page Attach fittings RC 2 specifications for fittings are shown in the test protocol or the drawings for installation fittings provided by the manufacturer. 5 Usage, processing 5.37

153 Fit center sealing bead 1. For positioning the center sealing bead, pre-drill holes for nipple head screw ( ) with a distance of 19 mm from the outside edge. Next, screw on. 2. Apply Cosmofen adhesive ( or ) onto center sealing bead and fit profile such that it is flush with the bottom edge of the sash. 3. In accordance with this figure, mark drilling holes on the center sealing bead and pre-drill (Ø 5 mm). From the top: Insert the first screw after 40 mm (A), then 3 off one after another at a spacing distance of 100 mm respectively (B). From below: also after 40 mm, insert first screw (A), 4 off at a spacing distance of 100 mm (B). In between distribute the screws such that the maximum distance is 200 mm (C). 40 mm 100 mm 100 mm 100 mm max. 200 mm A B B B C B B B 5 4. Next, pre-drill into sash using a drill (Ø 4 mm). 5. Screw on center sealing bead (4.8 x Ø 40 mm). 4 x 100 mm 40 mm B A Insert spacers 1. Cut 2 parts (W=100 mm, H=33 mm, Thickness=19 mm) VEKAPLAN S plate profile. 2. Push in at the top into both corners of the sliding sash. Push in to such an extent that there remains sufficient space ( 50 mm) for guide slides. 3. Before glazing: insert sliding sash and screw in spacers from the glass rebate. Next, glaze Usage, processing

154 Glazing/assembly Assembly and glazing guidelines Glazing bead overview

155 Assembly and glazing guidelines! Please note! Please read with care the following instructions on assembly and glazing! 1. Horizontally align the bottom threshold profile and embed the same along its entire length. 2. Secure the top frame against bending. This must be particularly complied with in the case of Plan D, C and F. 3. Align the frame vertically and in alignment. Use suitable fixing material to anchor the frame in the structural body. The fastening distance may be maximally 700 mm. 4. Check the squareness of the window aperture! 5. Insert the sliding sash into the frame. 6. Align the sliding sash toward the locking side and appropriately block the same. 7. Glaze sliding sash and fixed sash. Support blocks Spacing blocks 6 Additional instructions on how to plan and execute an assembly are to be found here: ASSEMBLY INSTRUCTIONS Synthetic material WINDOWS AND DOORS QUALITY ASSOCIATION Synthetic material window systems Baumschulallee Bonn Telephone: +49 (0) /55 Fax: +49 (0) QKE.Bonn@t-online.de 6.2 Glazing/assembly

156 Assembly and glazing guidelines i Info Some matters described in this documentation do not refer explicitly to the special system lift/slide door. To this extent such information is of a general nature which can be transferred to various different profile systems. Processing glazing beads Cutting glazing beads Cut all glazing beads on the glazing bead saw, (seals in a quality suitable for cutting). When fitting glazing beads without any seal First cut the glazing bead. Next, apply the glazing seal (Art. no ). Use a pair of sealing pliers to cut the glazing seal to an exact length. When cutting glazing beads to 45 Cut the glazing beads to 45. At the end of the glazing bead, repsectively undercut the glazing base to 45. Using a saw blade combination the glazing bead will be cut off during the forward run and the engagement lug during the return run. This ensures that the welding bead is no longer an obstruction when inserting the glazing bead.! Please note! In the case of glazings < 400 x 400 mm, glazing beads can be difficult to insert. The following processing steps are required In addition you need to undercut the retaining feet and partially remove the same Clip on glazing beads Insert the mitred glazing beads. Ensure that you always insert the shorter glazing beads first, and then the longer glazing beads. Carefully tap in the glazing beads with a plastic or rubber hammer. Undo glazing beads Use a spatula to undo glazing beads. First, undo the longer glazing beads and next the shorter glazing beads. Respectively undo the glazing beads in the central section. To this end, press the spatula into the central section of the glazing beads between rebate platform and lower edge of glazing bead. Jack up the spatula so that the glazing bead lifts slightly. Repeat this process at short intervals sufficiently often until you are able to withdraw the glazing bead by hand. Glazing/assembly 6.3

157 Assembly and glazing guidelines Fitting blocks Purpose of block fitting Weight distribution of the pane toward the sash frame Permanent adjustment of the sash frame Ensure operability of the sash Prevent the possibility of direct contact of the pane with the sash frame Ventilation possibility Blocking material Bearing, spacer and glazing blocks as well as glazing rebate inserts and wedges must be made up such that they are resistant to weather and ageing influences. Their form must not change when under load. Glazing blocks and wedges made of synthetic material - such as hard PVC - have proven themselves in this regard. Glazing blocks 100 mm Thickness / 100 x 26 mm 100 x 30 mm 100 x 34 mm color 1 mm / white mm / blue mm / red mm / yellow mm / green mm / black Attachment of the glazing blocks The glazing rebate insert bridges the height difference of 3 mm between the rebate platform and the upper edge of the glazing bead holder. During and after assembly, edge settings at the end of the glazing rebate insert prevent any sliding of the glazing blocks positioned on the same. Glazing blocks should have a length of 100 mm and always be 2 mm wider than the glazing. The groove stoppers of the glazing rebate insert , fitted on the outside, prevent any uncontrolled pushing in of the glazing blocks. All glazing rebate inserts as well as glazing blocks should be secured permanently against sliding out of position, e.g. by means of silicone. Blocks that have sled out of position loose their functionality and have a detrimental effect on other functions. In such a case, e.g., the sash can no longer be opened and closed optimally or the block is located before the drainage slot. After the glass pane has been fitted with glazing blocks, the glazing beads must be fitted (see the guidelines for fitting glazing blocks). Distance of blocking from the corner approx. 100 mm Glazing rebate insert Glazing/assembly

158 Assembly and glazing guidelines Sequence of block fitting 1. Start at the bottom in a horizontal direction with the insertion of the blocks onto the glazing rebate insert. The block height should be 6 mm (3 mm glazing rebate insert + 3 mm block). 2. Set down the glass pane on the bottom blocks and carefully tilt the sash frame. 3. Ensure in particular that there is the necessary glazing rebate play in the area of the post connectors so as not to damage the glazing edges.! Please note! If you have inserted connectors in the upper section, there is an increased risk of glass fracture when swivelling in the glass pane. Therefore suitable spacer blocks should be used and proceed with special care! 6 Glazing/assembly 6.5

159 Glazing bead overview, M1:2 Special glazing bead 40 x 21 mm 40 Model version, white and film-covered Article no. Glazing thickness / 7 / 8 21 Contour SOFTLINE 36 x 21 mm 36 Model version, white and film-covered Article no. Glazing thickness * 10 / 11 / Contour TOPLINE 32 x 21 mm 32 Model version, white and film-covered Article no. Glazing thickness * 14 / 15 / Contour SOFTLINE 31.5 x 21 mm Model version, white and film-covered 31.5 Article no. Glazing thickness * Contour TOPLINE 29 x 21 mm 29 Model version, white and film-covered Article no. Glazing thickness * 17 / 18 / M.1:2 / Film application without two-sided single-sided * on request 6.6 Glazing/assembly

160 Glazing bead overview, M1:2 Contour TOPLINE 26 x 21 mm 26 Model version, white and film-covered Article no. Glazing thickness * 20 / 21 / Contour TOPLINE 23 x 21 mm 23 Model version, white and film-covered Article no. Glazing thickness / 24 / Contour SOFTLINE 23 x 21 mm 23 Model version, white and film-covered Article no. Glazing thickness / 24 / Contour SOFTLINE 23 x 21 mm Model version, white and film-covered Article no. Glazing thickness * 23 / 24 / Contour SOFTLINE 23 x 21 mm 23 Model version, white and film-covered Article no. Glazing thickness / 24 / M.1:2 / Film application without two-sided single-sided * on request Glazing/assembly 6.7

161 Glazing bead overview, M1:2 Contour TOPLINE 23.5 x 21 mm 23.5 Model version, white and film-covered Article no. Glazing thickness Contour SOFTLINE 23.5 x 21 mm 23.5 Model version, white and film-covered Article no. Glazing thickness Contour SWINGLINE 23.5 x 21 mm 23.5 Model version, white and film-covered Article no. Glazing thickness Contour SOFTLINE 23.5 x 21 mm Model version, white and film-covered Article no. Glazing thickness Contour SOFTLINE 21.5 x 21 mm Model version, white and film-covered Article no. Glazing thickness * M.1:2 / Film application without two-sided single-sided * on request 6.8 Glazing/assembly

162 Glazing bead overview, M1:2 Contour TOPLINE 20 x 21 mm 20 Model version, white and film-covered Article no. Glazing thickness / 27 / Contour SOFTLINE 19.5 x 21 mm 19.5 Model version, white and film-covered Article no. Glazing thickness Contour SWINGLINE 19.5 x 21 mm 19.5 Model version, white and film-covered Article no. Glazing thickness Contour TOPLINE 17 x 21 mm Model version, white and film-covered Article no. Glazing thickness / 30 / Contour SOFTLINE 17.5 x 21 mm Model version, white and film-covered Article no. Glazing thickness M.1:2 / Film application without two-sided single-sided * on request Glazing/assembly 6.9

163 Glazing bead overview, M1:2 Contour SWINGLINE 17.5 x 21 mm 17.5 Model version, white and film-covered Article no. Glazing thickness Contour SOFTLINE 15.5 x 21 mm 15.5 Model version, white and film-covered Article no. Glazing thickness Contour SWINGLINE 15.5 x 21 mm 15.5 Model version, white and film-covered Article no. Glazing thickness Contour TOPLINE 14 x 21 mm Model version, white and film-covered Article no. Glazing thickness / 33 / Contour TOPLINE 11 x 21 mm Model version, white and film-covered Article no. Glazing thickness / 36 / M.1:2 / Film application without two-sided single-sided * on request 6.10 Glazing/assembly

164 Glazing bead overview, M1:2 Contour SOFTLINE 11.5 x 21 mm 11.5 Model version, white and film-covered Article no. Glazing thickness Contour SWINGLINE 7.5 x 21 mm 7.5 Model version, white and film-covered Article no. Glazing thickness * Contour TOPLINE 6 x 21 mm 6 Model version, white and film-covered Article no. Glazing thickness * 40 / 41 / M.1:2 / Film application without two-sided single-sided * on request Glazing/assembly 6.11

165 Notes Glazing/assembly

166 Annex Heat transition coefficient 7.2 Standards VEKA colour range

167 VEKASLIDE: Company values Heat transition coefficient U value VEKASLIDE 2 part lift/slide doors. element height: 220 m, with insulating wedge Uf value*****: 1,56, Calculation in accordance with DIN EN Width Aw * Ag ** Yg value *** U g value **** [W/(m²K)] EnEV 2009 special glass 7 W (m K) 2.50 m Alu Warm m Alu Warm m Alu Warm m Alu Warm m Alu Warm m Alu Warm m Alu Warm Alu 6.00 m Warm Aw value* = total surface area of the window in m2; Aw = Ag + Af Ag value** = glazed surface area in m2 (g for glazing) Y g -value*** = Flat value for Alu: 0.07 W/(mK) or Warm: 0.05 W/(mK), depending on the glazing Y assembly -value not taken into account Ug values**** = according to EN 673, EN 674, EnEV2009 compliant Profiles with reinforcement in the window frame and sash frame Uf value***** = ift /1; ift /2; ift /3; ift /1; or average value for the profile combinations Formula: U V ( U = f 1-n A f 1-n ) + ( U ( A f 1-n g A ) + ( l Y + A g g ) g g ) 7.2 Indexes, Annex 08/2010

168 Standards Basic standards for the test values (Technical Specifications, Chapter 1) DIN EN 1027 (Driving rain resistance) DIN EN (Wind load resistance) DIN EN 1026 (Air permeability) 7 Indexes, Annex 7.3

169 Notes Indexes, Annex

170 VEKA colour range VEKA colour range Synthetic material profiles by VEKA provide for an optimum in facade design in accordance with the surrounding landscape and the requirements of architecture. Windows and doors in colour or a wooden decor provide expressive accentuations and open up a multitude of design possibilities. The VEKA colour range currently comprises more than 40 attractive colours. A special manufacturing process guarantees even colours and structures. All surfaces are weather resistant, resistant against environmental influences and easy to handle. Legend for film design Standard range Special film Special film metallic! Please note! The surfaces shown below will be supplied on multi-coloured carrier materials and are not completely available for each VEKA system. The profiles can be covered in film on one or both sides. Due to the necessary production planning please take into account the longer delivery periods for special films. The colour range available as standard as well as additional details are shown in the current VEKA price list golden oak walnut mahagony moor oak brown siena rosso siena noce winchester The figures and illustrations may show slight deviations from the original shades. Indexes, Annex 7.5

171 VEKA colour range douglas fir strip douglas fir Mountain pine oregon III Light oak rustic-style oak light grey (similar to RAL 7035) agate grey (similar to RAL 7038) silver grey (similar to RAL 7001) silver grey mat (similar to RAL 7001) silver grey non-granulated (similar to RAL 7001) basalt grey (similar to RAL 7012) anthracite grey (similar to RAL 7016) anthracite grey non-granulated (similar to RAL 7016) The figures and illustrations may show slight deviations from the original shades. 7.6 Indexes, Annex

172 VEKA colour range anthracite grey mat (similar to RAL 7016) brilliant blue (similar to RAL 5007) cobalt blue (similar to RAL 5013) steel blue (similar to RAL 5011) emerald green (similar to RAL 6001) moss-green (similar to RAL 6005) fir tree green (similar to RAL 6009) fir tree green mat (similar to RAL 6009) blue-green (similar to RAL 6004) flaming red (similar to RAL 3002) ruby-red (similar to RAL 3003) crimson (similar to RAL 3011) wine-red (similar to RAL 3005) blackish-brown The figures and illustrations may show slight deviations from the original shades. Indexes, Annex 7.7

173 VEKA colour range zinc-yellow (ähnlich RAL 1018) white (similar to RAL 9010) cream-white (similar to RAL 9001) papyrus-white (similar to RAL 9018) aluminum brushed earl platinum pyrite quartz platinum azul asphalt silver v copper crown platinum The figures and illustrations may show slight deviations from the original shades. 7.8 Indexes, Annex