ASS 70.HI Lift/Sliding and Sliding Doors Installation Guide
|
|
- Morris Park
- 5 years ago
- Views:
Transcription
1 ASS 70.HI Lift/Sliding and Sliding Doors Installation Guide
2 2 Schueco ASS 70.HI Lift/Sliding and Sliding Doors Installation Guide Installation guide IMPORTANT The ASS 70.HI door should be fitted by competent and trained installers. Please read this guide thoroughly before beginning the installation and follow the instructions and recommendations to ensure that the door is fitted correctly and functions satisfactorily. Failure to do so may void any written or implied warranty. As regulations governing the use of glazed windows and doors may vary according to region, it is the responsibility of the building owner, architect, contractor or installer to ensure the selected products conform with all applicable codes and regulations. Preparation Tools: No special installation tools are required. Checking the opening The frame must be fitted plumb and level within the opening. Sizes given for manufacture of the frame should be the tightest point of the opening minus 10 mm fitting tolerance. The structural integrity of the lintel is critical for the proper functioning of the unit and must not be twisted. It is very important that the fixing ground for the cill is flat, even and perfectly level. The sides of the opening should be plumb and square. A laser or other similar precise measuring equipment is useful to check these requirements. To avoid later problems do not install the unit until the opening has been fully and correctly prepared. Please refer to your order confirmation for opening direction/door leaf information.
3 ASS 70.HI Lift/Sliding and Sliding Doors Installation Guide Schueco 3 Identification of door type The ASS 70.HI is available as a sliding door or a lift/sliding door. Sliding doors have shorter operating handles which turn 90 0 and brush pile in the bottom edges of the leaves. Longer operating handles are used on lift/sliding doors which rotate180 0 together with epdm gasket on the leaf bottom edges. The doors are available with single, double or triple tracks in the following configurations: Unit type: single track Type 1A Type 1B Type 1D Unit type: double track Type 2A Type 2A/1 Type 2B Type 2C Type 2D Type 2D/1 Unit type: triple track Type 3E Type 3E/1 Type 3F Note: In single track designs the sliding leaves are outside. In double and triple track designs the sliding leaves are inside.
4 4 Schueco ASS 70.HI Lift/Sliding and Sliding Doors Installation Guide Door overview (double track) 2A/1 2D Bi-parting door meeting stiles Bi-parting door meeting stiles 1 Lift sliding handle 2 Sliding Lift handle sliding handle 3 Distance Sliding blockshandle 4 Rollers and lift mechanism Distance blocks 5 Lock mechanism Rollers and lift mechanism 6 Anti-lift blocks Lock mechanism Anti-lift blocks Additional interlock style lock option Art. No
5 ASS 70.HI Lift/Sliding and Sliding Doors Installation Guide Schueco 5 Outer frames There are three types of outer frame single track with the fixed glazing built into the frame with a mullion, double track and triple track. With the double and triple track versions the fixed leaves are the same as the sliding leaves but screw fixed into the outer frame with distance blocks. Single track outer frame (fixed glazing built-in) Outside Double track outer frame Triple track outer frame Installation of outer frame into opening Place the frame in the opening and adjust until the frame is square, plumb and level. The top and bottom tracks must be parallel and the jambs must not be offset from each other. It is very important to fit the outer frame correctly otherwise problems may be encountered when fitting the door leaves. Where possible use Schueco fixing lugs Art. No which are attached to the grooves in the outer frame. Alternatively use 10 mm dia. fixing dowels to suit sub-structure. Always fix through the aluminium and not the thermal break. Make sure that the opening direction has been taken into account and that the water drain holes face to the outside. Fixing lug Art. No mm dia.dowel fixing
6 6 Schueco ASS 70.HI Lift/Sliding and Sliding Doors Installation Guide Outer frames Typical cill detail showing concealed drainage. Cill detail showing optional PVC-U insulating base profile (Art. No ) together with outside flush drainage gutter.
7 ASS 70.HI Lift/Sliding and Sliding Doors Installation Guide Schueco 7 Installation of outer frame fixing the head and jambs Fixings should start at 150 mm from the corners, utilising plastic packers as necessary to make sure the frame is level and plumb in the opening. Then fix at maximum 600 mm centres until the frame is fully secured all round. Use fixing lugs in preference to dowels. If fixing dowels are used then position under cover profiles in jambs and cill. Seal the holes in the cill before inserting dowel as water is drained in this area. In the head, dowels can be fixed under the guide rail. Dowel and lug fixing points in outer frame Sliding leaf/jamb / Fixing lug attachment groove Fixed leaf/jamb/ Seal hole before inserting fixing dowel Illustrations show door type 2A/1 (double track, sliding panel on inside)
8 8 Schueco ASS 70.HI Lift/Sliding and Sliding Doors Installation Guide Fixed leaf installation (double and triple track doors) Remove the interlock cover profiles 1 from the fixed and sliding leaves prior to installation. Check that door stop 2 and distance blocks 3 have been factory fitted to the fixed leaf. Distance blocks and door stop Lift the fixed leaf up into head frame and drop onto the distance blocks which are already screwed to jamb (x2) and cill (x2). Slide leaf towards jamb to engage on distance blocks. Fix leaf into outer frame through the prepared holes with 4.8 x 80 mm screws, ensuring leaf is seated correctly at cill. The last distance block is then slid into the top of the leaf. Caution: when engaging leaves into head make sure that distance blocks 3 do not become dislodged. Fitting the cover profiles Apply cover profiles to interlock styles 1, outer frame jambs 4 and 5, threshold 6. There is no threshold cover if all leaves slide. 4 < slider fixed outside 4 5 6
9 ASS 70.HI Lift/Sliding and Sliding Doors Installation Guide Schueco 9 Sliding leaf installation, all types Before inserting the sliding leaf check that tolerance pieces 4 are located in top of leaf. There will be 2 or 3 pairs, depending on leaf width Insert the sliding leaf into head and lower onto rollers at cill. Slide leaf and check correct vertical alignment of interlocks. Check locking operation. When operation is correct, fit anti-lift blocks 5 in head frame above sliding leaf. 5 Note that rollers are not adjustable. Important With bi-parting lift/sliding doors the master leaf must be unlocked, raised and moved first, after which the secondary leaf can be operated. To close, the secondary leaf must be closed first and lowered followed by the master leaf x 150 The door can now be glazed (see page 11).
10 10 Schueco ASS 70.HI Lift/Sliding and Sliding Doors Installation Guide Installation of single track doors Single track doors differ from double and triple track doors in that the sliding leaf is on the outside and the fixed glazing unit is inserted directly into the frame which incorporates a mullion. Outside Outside Sliding leaf Fixed glazing Illustrations show optional additional factory-fitted foam insulation Fixed Sliding > Outside
11 ASS 70.HI Lift/Sliding and Sliding Doors Installation Guide Schueco 11 Glazing Insert glazing bridges 1 and packers into the sliding and fixed frames. Fit the glazing beads, complete with plastic clips 2. Clips are fitted approximately 50 mm from each end and then at mm centres. Double track Single track Viewed from outside Viewed from outside Load bearing packer Spacer packer Glazing bead clip
12 12 Schueco ASS 70.HI Lift/Sliding and Sliding Doors Installation Guide Sealing Cavities between frame and wall should be packed with mineral wool and a silicone seal applied around the outside perimeter of the frame. To facilitate the quality of the perimeter seal, a suitably dimensioned polyethylene backing rod should first be inserted. The sealant manufacturer s instructions should be followed. Sealing and/or the addition of trims around the internal frame perimeter should be carried out as appropriate. Mineral wool Polyethelene backing rod Silicone seal
13 ASS 70.HI Lift/Sliding and Sliding Doors Installation Guide Schueco 13 Final inspection Remove any debris from the track area Before leaving site: test the unit and make sure tracks are clean and clear of any debris that could damage or affect the operation of the rollers. Make sure drain holes are clear. Explain operation and locking functions to the user. Ensure all keys are left with user. Leave door Operation & Maintenance Guide with user.
14 14 Schueco ASS 70.HI Lift/Sliding and Sliding Doors Installation Guide Section details
15 Section details ASS 70.HI Lift/Sliding and Sliding Doors Installation Guide Schueco 15
16 16 Schueco ASS 70.HI Lift/Sliding and Sliding Doors Installation Guide Section details
17 Schueco UK Ltd Schueco System solutions for windows, doors, façades and solar products. Together with its worldwide network of partners, architects, specifiers and investors, Schueco creates sustainable building envelopes which focus on people and their needs in harmony with nature and technology. The highest demands for design, comfort and security can be met, whilst simultaneously reducing CO 2 emissions through energy efficiency, thereby conserving natural resources. The company and its Metal, PVC-U and New Energies divisions deliver tailored products for newbuilds and renovations, designed to meet individual user needs in all climate zones. With more than 5,000 employees and 12,000 partner companies, Schueco is active in 79 countries and achieved a turnover of 1.8 billion euros in The illustrations in this brochure are only examples of Schueco products
ASS 70 FD folding/sliding door installation guide
ASS 70 FD folding/sliding door installation guide 2 Preparation IMPORTANT These doors should be fitted by competent and trained installers. Please read these instructions thoroughly before beginning the
More informationASS 70 FD folding / sliding door. Installation Guide
ASS 70 FD folding / sliding door Installation Guide IMPORTANT! These doors should be fitted by competent and trained installers. Please read these instructions thoroughly before beginning the installation.
More informationInstallation - Sub Cills
Installation - Sub Cills Fitting of Subcill Drainage paths through the sub-cill can be seen on the illustration alongside so care must be taken to ensure they are not obstructed and that screw fixings
More informationpatio door installation guide
patio door installation guide Measuring & surveying p2 Mechanical jointing p5 Installation p5 Hardware adjustment p7 Sealing of outer frame p7 Cleaning p7 Walk through clearances p8 Minimum and maximum
More informationVertical Slider Section Detail
Vertical Slider Section Detail PRODUCT GUIDE Main & Bead Profiles 128 42 69 VS01 - Outer frame 150 139 210 189 60 52 52 52 48 30 42 60 18 72 90 18 60 VS02 - Cill VS14 - Cill 18 VS03 - Top Sash VS04 - Standard
More informationSMART SYSTEMS VISOGLIDE+ INSTALLTION GUIDE
SMART SYSTEMS VISOGLIDE+ INSTALLTION GUIDE Please read guide before beginning any installation. Instructions/Guides Keys & Handle Screw Covers Interlock Covers Anti-Lift & Rubber Stops Anti-Lift for Slim
More informationIn-line Patio Fabrication & Installation
In-line Patio Fabrication & Installation Instructions 2 Pane Patio p2 Cutting and Preparation p2 Welding and Cleaning p2 Assembly p2 Fabrication Instructions for 3/4 Pane Lock Style p3 Installation (removable
More informationINSTALLATION INSTRUCTIONS. Thermal Entrances AA 250/AA 425 THERMAL DOOR WITH TRIFAB 601/601T FRAMING
JANUARY, 2014 1 INSTALLATION Thermal Entrances AA 250/AA 425 THERMAL DOOR WITH TRIFAB 601/601T FRAMING INSTRUCTIONS 2 FRAME ASSEMBLY JANUARY, 2014 601442 SHEAR BLOCK BALL BEARING NRP BUTT (FACTORY APPLIED
More informationFolding Sliding door system
Folding Sliding door system Installation guide V1.1 Nov 2014 p2 This document is offered as guidance for WarmCore folding sliding door installations - for full survey and installation guidelines please
More informationInstallation Guide. Evolve bi-fold. 8. Door restrictor- optional p9. 1. Before you start p2. 9. Adjustment. 2. Measuring and surveying p2
Evolve bi-fold Installation Guide 1. Before you start p2 8. Door restrictor- optional p9 2. Measuring and surveying p2 3. Configuration details p4 4. Installation p5 5. Glazing p5 6. Glazing packer details
More informationInstallation Guide. Bi-fold Doors
Installation Guide Bi-fold Doors Installation Guide Components box 1. 6. 2. 3. 7. 5. 4. 8. Contents 1. Fixing plugs 2. Wedge gasket 3. Bottom trolley 4. Top trolley 5. Magnetic keep (x 2 if door height
More informationInstallation Guide. WarmCore. Folding Sliding door system. Glass Packing. Pre-Installation. Removing the Existing Door.
WarmCore Installation Guide Pre-Installation Glass Packing p5 Removing the Existing Door Glazing Sequence p6 Preparing the Opening Glass Packing Locations for Toe & Heel p6 Door Alignment Sill Options
More informationSliding Glass Door Assembly and Installation Guide
Sliding Glass Door Assembly and Installation Guide Index Door System Components and Hardware The following components are needed to complete the installation of your Sliding Patio Door unit. Check all
More informationSide Light Frame Pack Assembly Instructions
Please read this complete set of assembly instructions before starting the installation and only when you understand the construction method start to follow the step by step guide. IDENTIFY THE PACK CONTENTS
More informationFITTING INSTRUCTIONS FOR FOLDING SLIDING DOOR SYSTEM SF55 & SF75 WITH WEATHERED OR FLUSH TRACK
FITTING INSTRUCTIONS FOR FOLDING SLIDING DOOR SYSTEM SF55 & SF75 WITH WEATHERED OR FLUSH TRACK Please refer to your order or detailed sectional drawing (if requested) to assist you with the configuration
More informationSide Light Frame Pack Assembly Instructions
Side Light Frame Pack Assembly Instructions Please read this complete set of assembly instructions before starting the installation and only when you understand the construction method start to follow
More information4-lite Patio Door. Installation Instructions
4-lite Patio Door Installation Instructions IMPORTANT: Read the instructions and familiarize yourself with the door parts and pieces before beginning assembly and installation. Note: Only the 5-0 x 6-8
More informationVYTEX PREMIUM SLIDING GLASS DOOR. Table of Contents. Precautions and Safety 2. Tools Required...3. Inspect and Prepare Door...4
VYTEX PREMIUM SLIDING GLASS DOOR Table of Contents Precautions and Safety 2 Tools Required...3 Inspect and Prepare Door...4 Hardware and Parts Check List....4 Master Frame Assembly 5 Master Frame Installation..7
More informationPatio door. Installation guide
Patio door Installation guide The following installation guide is designed to show you the best way to fit the Liniar sliding patio door. y following the details within you will be able to give your customer
More informationVinyl Windows and Doors Manufactured by Pella Corporation
Vinyl Windows and Doors Manufactured by Pella Corporation Part Number: V981255 2009 Pella Corporation INSTALLATION INSTRUCTION - INSTRUCCIONES DE INSTALACIÓN FOR BOW WINDOWS WITHOUT HEAD AND SEAT BOARD
More informationMira Premium Series Bi-Parting French Sliding Patio Door Installation Instructions
PREMIUM SERIES W I N D O W S Mira Premium Series Bi-Parting French Sliding Recommended Tools & Accessories Tape Measure Level (3 or longer) Hammer Power Screwdriver Load bearing Shims Flashing (recommended)
More informationArchitect: Daluz/González Architekten Photo: Peter Baracchi CP 155 SLIDING DOOR INSTALLATION GUIDE. Edition 15/21
Architect: Daluz/González Architekten Photo: Peter Baracchi CP 155 SLIDING DOOR INSTALLATION GUIDE Edition 15/21 INDEX 1. IMPORTANT INFORMATION... 4 1.1. Lift & slide door overview... 5 1.2. Details...
More informationCurtain Wall Installation Guide
Curtain Wall Installation Guide Curtain Wall Installation Guide 1 IMPORTANT NOTICES! Important Notices & Information Manufacturer s Notes: The building envelope must be correctly prepared with weather
More informationWOOD OUT SWING AWNING, CASEMENT, & HOPPER WINDOW
WOOD OUT SWING AWNING, CASEMENT, & HOPPER WINDOW INSTALLATION GUIDE READ SPECIFIC INSTALLATION INSTRUCTIONS COMPLETELY BEFORE STARTING ANY INSTALLATION Failure to install and maintain our product according
More informationDOOR BiFOLD DOOR SET (3 + 1)
3 4 DOOR BiFOLD DOOR SET (3 + 1) Bespoke and Standard Sizes 3.6M - 3590mm W x 2090mm H 4.0M - 3990mm W x 2090mm H IB73HEP431 - ISSUE B All products must be installed in accordance with accepted good trade
More informationHow to operate (folding)
How to operate (folding) LEFT HAND STACKING OUTWARD OPENING How to operate (folding) RIGHT HAND STACKING OUTWARD OPENING LOCK BOTH LEVER HANDLE AND FLAT HANDLE UTILISING THE D-HANDLE LOCATED ABOVE THE
More informationSeries 7650 Installation Instructions Sliding Glass Door
Series 7650 Installation Instructions Sliding Glass Door Things to Know Before You Start Things to Know Before You Start Removal of Old Fenestration Products Ensure any old fenestration products are removed
More informationVinyl Windows and Doors
Vinyl Windows and Doors Part Number: V983571 2011 Pella Corporation INSTALLATION INSTRUCTION - INSTRUCCIONES DE INSTALACION 350 SERIES WINDOW INTO EXISTING WOOD FRAME WINDOW Lea las instrucciones en español
More informationFor Installer. Duration Windows. Assembly Guide Durafold 1000
For Installer Assembly Guide Durafold 1000 Contents Title Page Number Handling Manual Blinds 4 Handling Electronic Blinds 5 Drainage 63 Outer Frame Assembly (Kit Form Door Only) 7 15mm Low Threshold Assembly
More informationYSD 400 Sliding Door System Installation Manual
System Installation Manual 2006 YKK AP America Inc. is a subsidiary of YKK Corporation of America. TABLE OF CONTENTS Installation Notes........................................ Page ii PARTS DESCRIPTION
More informationSeries 7600 Installation Instructions Aluminum Multi-Slide Door (Pocketing)
Series 7600 Installation Instructions Aluminum Multi-Slide Door (Pocketing) Things to Know Before You Start Things to Know Before You Start Removal of Old Fenestration Products Ensure any old fenestration
More informationInstallatIon InstructIons for 2-lIte PatIo Door unassembled
InstallatIon InstructIons for -lite PatIo Door unassembled tools & materials You will need: Measuring Tape Pencil Shims Drill & Drill bits: 6", 8", 5 6", 7 6" Utility Knife High-Performance Premium Silicone
More informationINOVO 2-LITE SLIDING PATIO DOOR
INOVO 2-LITE SLIDING PATIO DOOR ASSEMBLY AND INSTALLATION INSTRUCTIONS IMPORTANT: READ THE INSTRUCTIONS AND FAMILIARIZE YOURSELF WITH THE DOOR PARTS AND PIECES BEFORE BEGINNING ASSEMBLY AND INSTALLATION.
More informationSTACKING MULTI-SLIDE DOOR SYSTEM INSTALLATION INSTRUCTIONS
STACKING MULTI-SLIDE DOOR SYSTEM INSTALLATION INSTRUCTIONS 1290363 Revision 1 12/16 Page 1 Weather Shield Mfg., Inc. NOTICE CAUTION! Failure to install and maintain our product according to these instructions
More informationMULTISLIDE DOORS INSTALLATION GUIDE & SITE PREPARATION
MULTISLIDE DOORS INSTALLATION GUIDE & SITE PREPARATION TOOLS AND SUPPLIES 1 TOOLS CHECK LIST 1. laser level 2. hammer 3. pry bars 4. ladders 5. utility knife 6. screw gun 7. applicator foam gun 8. "j"
More informationINSTALLATION INSTRUCTION FOR CLAD BOW WINDOWS WITHOUT HEAD AND SEAT BOARD
2008 Pella Corporation Part Number: 80KG0101 INSTALLATION INSTRUCTION FOR CLAD BOW WINDOWS WITHOUT HEAD AND SEAT BOARD Note: These instructions may be used for all Pella Bow windows that do not have a
More informationPocket Door Installation Instructions
Installation Instructions Before getting started: Read instructions thoroughly. Be sure that you have the necessary tools and materials before starting the installation. Consult your local building code
More informationFOLDING DOOR - FOR FACTORY ASSEMBLED JAMBS WITH APPLIED SILL
FOLDING DOOR - FOR FACTORY ASSEMBLED JAMBS WITH APPLIED SILL READ SPECIFIC INSTALLATION INSTRUCTIONS COMPLETELY BEFORE STARTING ANY INSTALLATION Failure to install and maintain our product according to
More informationHeavy Wall Applied Stop Tube Frame and Door Installation
INSTALLATION INSTRUCTIONS Heavy Wall Applied Stop Tube Frame and Door Installation Read all instructions before beginning installation. These instructions are provided to help prevent installation problems
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Thermally Broken Framing and Door Installation SL-450TB (2" x 4-1/2" with 1" Glazing) & SL-600TB (2" x 6" with 1" Glazing) IMPORTANT: Read all instructions before beginning installation.
More informationThermally Broken Framing and Door Installation
INSTALLATION INSTRUCTIONS Thermally Broken Framing and Door Installation IMPORTANT: Read all instructions before beginning installation. These instructions are provided to help prevent installation problems
More information3-LITE PATIO DOOR INSTALLATION INSTRUCTIONS
3-LITE PATIO DOOR INSTALLATION INSTRUCTIONS IMPORTANT: Read the instructions and familiarize yourself with the door parts and pieces before beginning assembly and installation. TOOLS NEEDED: Tape Measure
More informationINSTALLATION INSTRUCTIONS FOR A&L PRODUCTS
INSTALLATION INSTRUCTIONS FOR A&L PRODUCTS AUGUST 2017 1 RECOMMENDED BUILDING IN-DETAIL Should you require further information, please contact A&L Windows on 1800 441 414 2 IMPORTANT IMPORTANT Allow Vinyl
More informationWINDOW REPLACEMENT INSTRUCTIONS FOR CASEMENT, DOUBLE-HUNG AND CLAD FRAME WINDOWS USING FRAME SCREWS
WINDOW REPLACEMENT INSTRUCTIONS FOR CASEMENT, DOUBLE-HUNG AND CLAD FRAME WINDOWS USING FRAME SCREWS These instructions were tested developed for replacing windows in wood-frame wall construction systems
More informationInSTallaTIon InSTruCTIonS For 4-lITe PaTIo Door unassembled
InSTallaTIon InSTruCTIonS For 4-lITe PaTIo Door unassembled Measuring Tape Pencil Shims Drill & Drill bits: 6", 8", 5 6", 7 6" Tools & materials You Will need: Square Hammer or Mallet Level Stiff Putty
More informationLiniar Window. installation guide
Liniar Window installation guide This installation guide is designed to show you the best way to fit Liniar windows, and covers all styles of window made from Liniar s lead-free 70mm PVCu profile. Not
More informationSERIES 4070-T GENERAL ASSEMBLY AND INSTALLATION INSTRUCTIONS
Table of Contents I. Care and Maintenance... 2 II. Tools / Materials, Sealant Requirements, & Anchor Instructions... 2 III. Structure Verification & Sub-Sillpan Installation... 3 1. Opening Verification...3
More informationINSTALLATION INSTRUCTION - INSTRUCCIONES DE INSTALACIÓN FOR CLAD CASEMENT & AWNING WINDOW VENTANA DE DOS HOJAS CON REVESTIMIENTO
2008 Pella Corporation Part Number: 801P0101 INSTALLATION INSTRUCTION - INSTRUCCIONES DE INSTALACIÓN FOR CLAD CASEMENT & AWNING WINDOW VENTANA DE DOS HOJAS CON REVESTIMIENTO Corner Corner Top Fin Corner
More informationFITTING INSTRUCTIONS FOR FOLDING SLIDING DOOR SYSTEM SF75H
FITTING INSTRUCTIONS FOR FOLDING SLIDING DOOR SYSTEM SF75H 01603 424434 Please refer to your order or detailed sectional drawing (if requested) to assist you with the configuration of the system supplied
More informationVinyl Windows Manufactured by VPI Quality Windows
Vinyl Windows Manufactured by VPI Quality Windows Part Number: 531&591 Installation 531 & 591 SERIES SLIDING AND HUNG WINDOW INSTALLATION INSTRUCTIONS Installation Instructions for Typical Construction.
More informationPhone # La Jolla Doors. Block Frame Installation Manual Aluminum Frame with either Vinyl or Aluminum Panels
Phone # 800-440-8785 www.lajolladoors.com La Jolla Doors Block Frame Installation Manual Aluminum Frame with either Vinyl or Aluminum Panels Thank you for choosing La Jolla Doors In this manual you will
More informationXL JOINERY LTD LA PORTE VISTA MODULAR 3 ASSEMBLY INSTRUCTIONS
XL JOINERY LTD LA PORTE VISTA MODULAR 3 2090mm High x 4687mm Wide ASSEMBLY INSTRUCTIONS READ AND UNDERSTAND THESE INSTRUCTIONS FULLY PRIOR TO STARTING INSTALLATION. IT IS STRONGLY RECOMMENDED THAT A COMPETENT
More informationSERIES 5001 SLIDING GLASS DOOR PATIO DOORS INSTALLATION GUIDE
PATIO DOORS INSTALLATION GUIDE These instructions cover general installation conditions. Improper installation could affect your doors operation and warranty. Deviations from these instructions should
More informationVisioGlide 100 System W4F Four doors 2 fixed, 2 sliding
Balcony Systems 2011 Visio Glide W4-F Curved Sliding Doors 4 doors: 2 fixed, and 2 sliding Installation guide 1. Insert silicone into the two bottom corners before closing the frame. 1 2. Connect top and
More information(Non Handed Kits) Slotted Hand Screwdriver. Power Driver & Bits. Work Gloves
Patio Door Kit Assembly Instructions -- 2-Panel Patio Door with Non-Assembled Frame and Assembled Sash Panels. (Non Handed Kits) Project Requirements: ~ This door was manufactured for installation into
More informationINSTALLATION INSTRUCTIONS IMPERVIA SLIDING PATIO DOOR WITH FINS
2008 Pella Corporation Part Number: 803V0101 INSTALLATION INSTRUCTIONS IMPERVIA SLIDING PATIO DOOR WITH FINS Installation Instructions for Typical Wood Frame Construction. These instructions were developed
More informationBlock Frame Inovo Patio Door/Transom/Sidelite Field Mulling Instructions. simonton.com/installation. If mulling sidelites, skip to Step 5.
Effective Date: 10/1/17 Tools Needed Kit Contents Safety Glasses Cordless Drill Phillips Screw Bit Two-step Drill Bit (3/8-1/8 ) Utility Knife Interior Mullion Exterior Mullion Cover Hardware Kit Clamps
More informationVanity Installation Instructions
Vanity Installation Instructions Segments of these instructions will relate to your vanity. Please read these instructions thoroughly and ensure the appropriate instructions are used during the installation
More informationVEKA GROUP PATIO DOOR PATIO DOOR PATIO DOOR UNCONTROLLED DOCUMENT AUTHOR PHIL GREGORY VEKA _IMAGINE PATIO_INSTALLER AID
VEKA GROUP VEKA _IMAGINE PATIO_INSTALLER AID UNCONTROLLED DOCUMENT VEKA GROUP USE OF THIS MANUAL Guidelines Advice & General Information. Although it is possible to manufacture a five metre four pane patio
More informationGENERAL INSTALLATION GUIDELINES
1551 MT. ROSE AVENUE YORK PA 17403-2909 (717) 849-8100 GENERAL INSTALLATION GUIDELINES For Receptor Systems Approved 08/31/2018 Installation Guideline Disclaimer This document contains general installation
More informationINOVO 4-LITE SLIDING PATIO DOOR ASSEMBLY AND INSTALLATION INSTRUCTIONS
INOVO 4-LITE SLIDING PATIO DOOR ASSEMBLY AND INSTALLATION INSTRUCTIONS IMPORTANT: READ THE INSTRUCTIONS AND FAMILIARIZE YOURSELF WITH THE DOOR PARTS AND PIECES BEFORE BEGINNING ASSEMBLY AND INSTALLATION.
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS SHOWER STUDIO GLIDE Englefield has a history of making superb showers and their popularity is testament to their quality and affordability. It s the details that Englefield cares
More informationPvcu Bi Folding Doors Fitting Instructions.
Pvcu Bi Folding Doors Fitting Instructions. THE FOLLOWING INSTRUCTIONS ARE GIVEN IN GOOD FAITH AND ARE FOR GUIDANCE ONLY. NO RESPONSIBILITY WILL BE ACCEPTED FOR ANY MIS- INTERPRETATION. WHEN INSTALLING
More informationINTERIOR. Checkrail. Flashing tape
Pella Corporation 2007 Part Number: 808F0100 INSTALLATION INSTRUCTION - INSTRUCCIONES DE INSTALACION FOR PELLA PRECISION FIT DOUBLE-HUNG VENT WINDOW PARA LA VENTANA DE GUILLOTINA CON HOJA PRACTICABLE PRECISION
More informationDIANE MODEL PASS-THRU
INSTALLATION INSTRUCTIONS MODELS D101 AND D10 DIANE MODEL PASS-THRU 50 E. Vernon Avenue, Los Angeles, CA 90058-186 Phone: (800) 41-6144 EXT. 7760 Fax: (800) 458-7496 crlaurence.com Email: transaction@crlaurence.com
More informationINSTALLATION INSTRUCTIONS - INSTRUCCIONES PARA LA INSTALACIÓN CLAD WINDOWS WITH FLUSH FLANGE
2012 Pella Corporation Part Number: 81CP0101 INSTALLATION INSTRUCTIONS - INSTRUCCIONES PARA LA INSTALACIÓN CLAD WINDOWS WITH FLUSH FLANGE Lea las instrucciones en español en el reverso Installation Instructions
More informationFrameless Quadrant Enclosure. These instructions must be left with the user. Installation Guide W2-B
Frameless Quadrant Enclosure These instructions must be left with the user Installation Guide 1 1317134-W2-B Introduction Thank you for purchasing a quality Mira product. To enjoy the full potential of
More informationSERIES 3070-T MULTI-SLIDE ASSEMBLY & INSTALLATION INSTRUCTIONS
Table of Contents I. Care and Maintenance...2 II. Tools / Material & Sealant Requirements...2 III. Assembly and Installation...2 IV. Glazing Assembly...3 V. Panel Assembly...3 1. X Panel...3 2. O Panel...4
More information1200 SERIES 2 PANEL DOOR rev.1 DETAILED INSTALLATION INTRUCTIONS
1200 SERIES 2 PANEL DOOR 10.2013 rev.1 DETAILED INSTALLATION INTRUCTIONS GENERAL: Door elevations shown in these instructions are as viewed from the outside. X denotes the active or moving panel(s). O
More informationPVCu FOLD & SLIDE DOOR OUTWARD OPENING
PVCu FOLD & SLIDE DOOR OUTWARD OPENING STEP-BY-STEP FULLY ILLUSTRATED ASSEMBLY INSTRUCTIONS This product is covered by a 10 year manufacturer s guarantee. Should any part of it become defective due to
More informationFlashing Materials. Rough Opening Preparation
Installation Instructions for CertainTeed New Construction Windows Handling vinyl windows CAUTION: Always store vinyl windows and doors in an upright position on a slight angle. Never lay them flat or
More informationVanity Installation Instructions
Vanity Installation Instructions Segments of these instructions will relate to your vanity. Please read these instructions thoroughly and ensure the appropriate instructions are used during the installation
More informationGENERAL INSTALLATION GUIDELINES
1551 MT. ROSE AVENUE YORK PA 17403-2909 (717) 849-8100 GENERAL INSTALLATION GUIDELINES For Receptor Systems Approved 9/29/2017 Installation Guideline Disclaimer This document contains general installation
More informationINSTALLATION GUIDE WOOD PIVOTING CIRCLE/ OVAL
WOOD PIVOTING CIRCLE/ OVAL READ SPECIFIC INSTALLATION INSTRUCTIONS COMPLETELY BEFORE STARTING ANY INSTALLATION Failure to install and maintain our product according to these instructions will VOID any
More information4. Partially open the operating panel and tilt the top toward the interior of the door (Figure 4). Lift the panel off the sill and set it aside.
Effective Date: 10/1/2017 Tools Needed Kit Contents Hardware Kit Safety Glasses Cordless drill Phillips screw bit Two-step drill bit (3/8-1/8 ) utility knife Interior Mullion Exterior Mullion Cover clamps
More informationInstallation Instructions
Supafold Slide Aside System Three Fold Room Divider Installation Instructions Distinctive Doors Ltd Supafold Slide Aside Internal Folding System IMPORTANT: Before proceeding with the installation, and
More informationI n s t a l l a t i o n I n s t r u c t i o n s S E N T I N E L S E R I E S 1 50 SLIDING GLASS DOORS
I n s t a l l a t i o n I n s t r u c t i o n s S E N T I N E L S E R I E S 1 50 SLIDING GLASS DOORS Page 2-9: Installation Instructions, Figures 1, 2, & 3 Page 10-12: Figures A-1, A-2, & A-3: Installation
More informationIntegrity Polygon and Round Top Installation and Finishing Instructions
Integrity Polygon and Round Top Installation and Finishing Instructions 08/20/2004 70852 BEFORE YOU BEGIN IMPORTANT: Read these instructions thoroughly before beginning to install your Integrity Polygon
More information6400, 8400 and 9400 Series Sliding Patio Door
Contemporary 3 Panel Classic 5 Panel French Panel 6400, 8400 and 9400 Series Sliding Patio Door (O) Fixed Panel Left (X) Operating / Mullion Panel Right (X) Operating / Lock Panel Left (O) Fixed Panel
More informationKestrel Aluminium Systems Limited. Product Manual Section 11 Thermal Framing System - Fabrication. Manual Version
Limited Product Manual Section 11 - Fabrication Manual Version 23.0.1 Section 11.01 Fabrication 11.01.01 sheet 1 General guidelines for cutting and bar preparation Section 11 Contents Section 11.02 Fabrication
More information. crealco V I S TA F O L D B O T T O M R O L L E R F O L D I N G D O O R Index Legal Disclaimer 4 Profile Identification 5-7 Hardware Identification 8
. crealco V I S TA F O L D B O T T O M R O L L E R F O L D I N G D O O R VISTAFOLD SYSTEM PRODUCT MANUAL 2013 Wispeco (Pty) Ltd, All Rights Reserved Revision: June 2013 . crealco V I S TA F O L D B O T
More informationContemporary 3 Panel Classic 5 Panel French Panel
Contemporary 3 Panel Classic 5 Panel French Panel (X) Operating / Lock Panel Left (O) Fixed Panel Right Note : Glazing Beads For All Panel Face To The Exterior 2 Panel XO Left Is Shown Above Opposite =
More informationCGI Series 560 SGD Installation Instructions
CGI Series 560 SGD Installation Instructions Read these instructions completely before beginning to install. Become familiar with what type of installation will be required. This door can be installed
More informationPanoramic Door Block Frame Installation Manual
Units 5 & 6 Park House Lane Sheffield S9 1XA 01142 439593 Panoramic Door Block Frame Installation Manual Panoramic Door Block Frame Door Installation Guide 10-10-17 1 of 1 Thank you for choosing Panoramic
More informationCasement/ Casement Picture Pocket Installation (Interior) Tools: (Not Provided by Manufacturer) Fig Supplies: (Not Provided by Manufacturer)
Casement/ Casement Picture Pocket Installation (Interior) Tools: (Not Provided by Manufacturer) Tape Measure Utility Knife Fig. 0-1 Drill Level Putty Knife Pry bar Square Caulk Gun Hammer Safety Glasses
More informationFlushglaze For Framed Openings and Horizontal Panels. Window System Installation Guide
Flushglaze 4500 For Framed Openings and Horizontal Panels Window System Installation Guide January 2017 BENCHMRK Welcome to Kingspan, global leaders in the design and manufacture of insulated metal panels
More informationINSTALLATION INSTRUCTION INSTRUCCIONES DE INSTALACIÓN FOR CLAD HINGED PATIO DOOR PUERTA DE BISAGRA PARA PATIO
2008 Pella Corporation Part Number: 801V0101 INSTALLATION INSTRUCTION INSTRUCCIONES DE INSTALACIÓN FOR CLAD HINGED PATIO DOOR PUERTA DE BISAGRA PARA PATIO REMEMBER TO USE APPROPRIATE PERSONAL PROTECTIVE
More informationINSTALLATION MANUAL STOREFRONT DOORS
INSTALLATION MANUAL STOREFRONT DOORS www.aluflam-usa.com SYSTEM DESCRIPTION - Extruded and filled aluminum framing, tested and approved by UL - 3-3/8 frame depth - Clear, fire-rated safety glazing - Door
More informationPicture Window and Welded Dead-Lite (Exterior) Tools: (Not Provided by Manufacturer) Fig Supplies: (Not Provided by Manufacturer) Fig.
Picture Window and Welded Dead-Lite (Exterior) Tools: (Not Provided by Manufacturer) Tape Measure Utility Knife Fig. 0-1 Drill Level Putty Knife Pry bar Square Foam Gun (Optional) Caulk Gun Hammer Safety
More informationTHERMO-FIT REPLACEMENT WINDOW INSTALLATION INSTRUCTIONS (BRICKMOULD / NO NAILING FLANGE)
THERMO-FIT REPLACEMENT WINDOW INSTALLATION INSTRUCTIONS (BRICKMOULD / NO NAILING FLANGE) fig.3 Casement, Awning, Fixed Casement, Direct-Set, Double-Hung, Single-Hung & Horizontal Slider Windows Materials
More informationVinyl Windows and Doors Manufactured by VPI Quality Windows
Vinyl Windows and Doors Manufactured by VPI Quality Windows Part Number: 511_Installation ENDURANCE CASEMENT\AWNING\PW INSTALLATION INSTRUCTIONS Installation Instructions for Typical Construction These
More information1 Removing The Screen Track, Screen and Screen Rollers Note: The screen remains in the track while the track is removed and/or installed.
Sliding Door Screen and Screen Track Replacement Service Instruction These instructions apply to: Architect Series 12/2004-Current Designer Series 3/2005-Current Tools Required: #2 Phillips head screwdriver
More informationINSTALLATION INSTRUCTIONS - INSTRUCCIONES DE INSTALACION FOR HURRICANESHIELD IMPACT-RESISTANT DOUBLE-HUNG, SINGLE-HUNG AND SIMULATED-HUNG
2008 Pella Corporation Part Number: 80ED0101 INSTALLATION INSTRUCTIONS - INSTRUCCIONES DE INSTALACION FOR HURRICANESHIELD IMPACT-RESISTANT DOUBLE-HUNG, SINGLE-HUNG AND SIMULATED-HUNG Instrucciones en español
More informationINSTALLATION INSTRUCTIONS for Wood/Clad Wood Windows without Exterior Trim or Nailing Fin (JII025) ImpOrTaNT INFOrmaTION & GlOssary.
for Wood/Clad Wood Windows without Exterior Trim or Nailing Fin (JII025) Thank you for selecting JELD -WEN products. Attached are JELD-WEN s recommended installation instructions for metal clad wood windows
More informationC D. Secondary Glazing Fixed Unit. Do not scale 1 to 1. Frame 301 Face Fix. 19.8mm. Typical Elevation. Top hung over fixed.
Secondary Glazing Fixed Unit 19.8mm 14.0mm Frame 301 Face Fix Top hung over fixed Fixed unit Fixed unit using overlap section 310 Glazing available in 4mm 6mm and 6.4mm Laminate Glass o not scale 1 to
More informationEst Aluminium Profile Stockists
. crealco PA L A C E CREALCO PALACE PRODUCT MANUAL Revision: November 2012 . crealco PA L A C E Index Legal Disclaimer 4 Profile Identification 5-7 Hardware Identification 8 Double Track Configurations
More informationSwing Door Installation Manual
Manual 20D/35D/50D 20DH/35DH 40M/50M 25FD 35XT 50XT 01-4000-03 2010 YKK AP America Inc. is a subsidiary of YKK Corporation of America. TABLE OF CONTENTS Installation Notes.......................................
More informationINSTALLATION INSTRUCTION - INSTRUCCIONES DE INSTALACIÓN FOR CLAD SLIDING PATIO DOOR PUERTA CORREDERA PARA PATIO
2008 Pella Corporation Part Number: 801W0103 INSTALLATION INSTRUCTION - INSTRUCCIONES DE INSTALACIÓN FOR CLAD SLIDING PATIO DOOR PUERTA CORREDERA PARA PATIO Corner Fin Corner Door Top Nailing Fin Side
More informationEuro Series Product Installation Guide
Euro Series Product Installation Guide Introduction... 3 Tools Required... 4 Installation Instructions... 5 Operation and Maintenance... 7 Hinge Adjustments... 10 Door Hinge & Locking Point Adjustments...
More informationInstallation Guidelines for all Quaker products with nail fins New Construction nail fin installation with a Zip sheathing system.
www.quakerwindows.com www.quakercommercialwindows.com PO Box 128 504 Highway 63 South Freeburg, MO 65035 800-347-0438 573-469-4151 (fax) Installation Guidelines for all Quaker products with nail fins New
More information