A. General millwork and custom cabinetry unless specified herein or so noted on plans as included within this section.
|
|
- Eustacia Ferguson
- 5 years ago
- Views:
Transcription
1 SECTION MANUFACTURED CASEWORK PART 1 GENERAL 1.1 SUMMARY A. Section includes: 1. Laminated Plastic Casework 2. Laminated Plastic Counter Tops. B. Description of Work: 1. Special and modified stock design pre-assembled units for installation as movable, fixed, or builtin, as indicated. 2. The use of dimensions and specific requirements set forth in Drawings and Specifications are not intended to preclude the use of other acceptable manufacturer s product or procedures which may be equivalent, but are given for purpose of establishing standard of design and quality for materials, construction, and workmanship. 3. Construct cabinets indicated to receive sinks to allow for installation of sinks for sizes indicated. Coordinate with Division 22 for sink sizes. 4. Plastic laminate countertops. C. Definitions: 1. Exposed Portions of Casework: Include surfaces visible when doors and drawers are closed. Bottoms of casework more than 4 feet above floor and tops less than 6 feet 6 inches above floor shall be considered as exposed. Visible members in open cases or behind glass doors also shall be considered as exposed portions. Any unit exterior side surface that is visible after installation. 2. Semi-Exposed Portions of Casework: Includes those members behind opaque doors, such as shelves, divisions, interior faces of ends, case back, drawer sides, backs and bottoms, and back face of doors. Tops of casework 6 feet 6 inches or more above floor shall be considered semiexposed. 3. Concealed Portions of Casework: Include sleepers, web frames, dust panels, and other surfaces not usually visible after installation. D. Related Sections: The provisions of the General Conditions, Supplementary Conditions and the sections included under Division 1, General Requirements, are included as a part of this section. Related work specified elsewhere: 1. Section : Finish Carpentry 1.2 RELATED WORK SPECIFIED ELSEWHERE A. General millwork and custom cabinetry unless specified herein or so noted on plans as included within this section. B. Rubber, vinyl or other finished toe base. C. Blocking within walls. MANUFACTURED CASEWORK
2 D. Sinks, faucets, fittings, traps, stops, tail pieces, vacuum breakers, and other fixtures, electrical and mechanical runs and connections. E. Fixture installation/services connections: Setting and installation of equipment and fixtures, and related utility connections, are provided under the other sections of the Project Specification governing that utility. 1.3 REFERENCES (Refer Section ) A. Provide products and workmanship in accordance to: 1. National Electric Manufacturers Association (NEMA) 2. Architectural Woodwork Institute (AWI) 1.4 SUBMITTALS (Refer Section ) A. Submit the following for approval: 1. Manufacturers Literature. 2. Shop Drawings: Show fabrication and installation details, including plans, elevations, sections, and attachments to other work. Include section drawings of typical and special casework, work surfaces and accessories. Indicate locations of plumbing and electrical service field connection by others. 3. Samples: 6-inch square samples for each type of finish, including top and edge material. 1.5 QUALITY ASSURANCE (Refer Section ) A. Product designations, drawings indicate sizes, configurations, and finish material of educational casework by referencing designated manufacturer s catalog numbers. Other listed manufacturer s casework of similar sizes and door and drawer configurations, of same finish material, and complying with the Specifications will be acceptable. B. Manufactured casework systems must conform to design, quality of materials, workmanship and function as indicated. Minimum quality standards shall be custom grade in accordance with AWI Section 1600 with additional requirements herein. 1.6 PERFORMANCE REQUIREMENTS A. Countertops: Maximum deflection of 1/4 inch when a 100 lb/ft. load is applied. B. Shelving: Capable of supporting 25 pounds/sq.ft. 1.7 DESIGN REQUIREMENTS A. Design: Door/drawer: Flush between extended cabinet end panels for increased lateral door strength, safety, and security. Door/drawer and all leading cabinet body, shelf, and divider edges: 3mm PVC/ABS as specified herein. Overlay door designs and edgings other than specified are not acceptable. B. Lamination System: Doors, finished end panels, and other decorative exterior laminate surfaces: Laminated exterior with.028 inch high-pressure plastic laminate, and interior with.020 inch highpressure cabinet liner. Lamination with hybrid P.V.A. Type III water resistant adhesive. C. Structural Drawer Body: Drawer body: Recessed, fully bound (dadoed) and joint-glued all four sides. Provide under body stiffeners as specified herein. MANUFACTURED CASEWORK
3 D. Drawer Suspension: Standard drawer slides: Self-closing design, epoxy powder coated, with positive instop, outstop, and out-keeper. E. Structural Cabinet Support: Cabinet sub-base: Separate and continuous ladder-type platform design, leveled and floor mounted prior to cabinet body placement. Cabinet sides-to-floor are not permitted. 1.8 ACCESSIBILITY REQUIREMENTS A. Conform to the Americans with Disabilities Act Accessibility Guidelines (ADAAG) and State and Local Regulations. These requirements supersede Specifications in this Section. Meet the following special requirements where indicated as ADA, or by General Note: 1. Countertop Height: With or without cabinet below, not to exceed a height of 34-inches A.F.F, at a surface depth of 24-inches. 2. Knee-Space Clearance: Minimum 29-inches A.F.F. at apron, and 30-inches clear span width inch Deep Shelving, Adjustable or Fixed: Not to exceed 9-inches AFF to 54-inches A.F.F. 4. Wardrobe Cabinets: Furnished with rod/shelf adjustable to 48-inches A.F.F. at a maximum 21- inch shelf depth. 5. Sink Cabinet Clearances: In addition to above, upper knee-space frontal depth no less than 8 inches, and lower toe frontal depth no less than 11 inches, at a point 9 inches A.F.F., and as further described in ADAAG, Volume 56, Section PROJECT CONDITIONS A. Where field measurements cannot be made without delaying the work, establish dimensions and proceed with fabricating casework without field measurements. Coordinate construction to ensure that actual field dimensions correspond to established dimensions of shop drawings. B. HVAC system must be operating and maintaining temperature and relative humidity at occupancy levels during installation and for the remainder of the construction period. C. Coordinate layout and installation of metal framing and reinforcements in gypsum board assemblies for support of casework where required WARRANTY A. Manufacturer agrees to repair or replace components of casework that fail in materials or workmanship within specified warranty period. Failures include, but are not limited to, the following: 1. De-lamination of components or other failures of glue bond. 2. Warping of components. 3. Failure of operating hardware. 4. Deterioration of finishes. B. Warranty Period: Five years from date of Final Inspection and Acceptance DELIVERY, STORAGE, HANDLING A. Do not deliver or install casework until building is enclosed, wet work is completed, and HVAC system is operating and will maintain temperature and relative humidity at occupancy level through remainder of construction period. MANUFACTURED CASEWORK
4 B. Deliver casework only after painting, utility roughing-in, and similar operations have been completed in installation areas. If casework must be stored in other than installation areas, store only in areas where environmental conditions meet requirements specified by manufacturer. C. Take precautions to protect casework against damage during handling, storage, installation, until final acceptance. PART 2 PRODUCTS 2.1 COMPLIANCE A. All manufacturers listed herein without a designated product must comply with the requirements of the specification, and, additionally, with the requirements of a specific manufacturer s product if indicated. Products of other manufacturers will be considered for acceptance provided they equal or exceed the material requirements and functional qualities of the specification. Furnish the Substitution Request Form with complete technical data for evaluation for Architect s approval. Additional approved manufacturers will be issued by Addendum. Refer to Division MANUFACTURERS A. Reveal overlay series cabinets manufactured by: 1. TMI Systems Design Corp. (216) Polyvision Corp. (724) Stevens Cabinet Company (216) LSI Corporation of America, Inc. (216) PLASTIC LAMINATE A. General: ANSI/NEMA LD3-1995, high pressure laminate with Density of 90 pounds per cubic foot minimum for all grades. Colors selected from manufacturer's standard color list. Colors selected from full range of solid colors, patterns, or textured finish. Limit of one (1) color per cabinet face and five (5) colors per project. 1. Wilsonart International, Temple, Texas 2. Formica Corporation, Cincinnati, Ohio 3. Laminart, Elk Grove Village, Illinois 4. Nevamar Corp., Odenton, Maryland 5. Pionite Plastics Corp., Auburn, Maine 6. Arborite Forbo, Quebec, Canada B. Exposed Interior and Exterior Vertical Surfaces, and Shelves: GP28 (.028") with low lustre textured finish and conforming to NEMA VGS standards. C. Counter Top Plastic Laminate: NEMA GP-50 (.048 ) textured finish and conforming to NEMA HGS standards, balanced with backing sheet. D. Backing Sheet for Countertops: NEMA BKH, BK-20, (.020") E. Horizontals other than Countertops: GP28 (.028") with low lustre textured finish and conforming to NEMA HGS standards. F. Cabinet Liner: NEMA CL-20 (.020") cabinet liner. G. Backing Sheets for Semi-Exposed Surfaces: NEMA CL-20 (.020") cabinet liner. MANUFACTURED CASEWORK
5 H. Backing Sheets for Concealed Surfaces: NEMA CLS (.020 ) cabinet liner. Use to balance face laminate. I. Semi-exposed surfaces, except shelves:.020-inch thick CLS cabinet liner conforming to NEMA standards or melamine. J. Shelves:.028 inch thick minimum with low lustre textured finish and conforming to NEMA HGS standards. K. Melamine: NEMA LD3-1995, VGS standards (.028) and complying with ALA L. Melamine Faced Particleboard: Medium density particleboard complying with ANSI A208.1, Grade M- 2, with decorative surface of thermally fused, melamine impregnated web complying with ALA M. Particleboard: Industrial Grade, ANSI A , type M-2, made with no urea formaldehyde. For countertops with sinks, provide shop sanded exterior grade veneer core plywood, or phenolic resin particleboard Type 2-M-2 or 2-M-3. N. Edge Banding for Plastic Laminate Surfaces: Rigid PVC extrusions, machine applied edging, applied with hot-melt adhesive, through-color with satin finish, 3mm thick at doors and drawer fronts and countertops, and 1mm on other exposed and semi-exposed cabinet edges. O. Hardboard: Exposed or semi-exposed, ANSI A135.4, Class 1 tempered, smooth 2 sides. P. Hardwoods: Red oak, free of defects, selected for compatible grain and color and kiln dried to 7 percent moisture content. Concealed members hardwood, kiln-dried to 7%, mill option lumber. Q. Plywood: Hardwood plywood of selected species similar in color and grain to exposed wood. HPVA HP-1, 7-ply, Grade C faces and Grade J crossbands. Provide semi-exposed backs of plywood with exposed faces same species as faces. 2.4 MISCELLANIOUS MATERIALS A. Particleboard: Industrial Grade, ANSI A , type M-2. For countertops with sinks, provide shop sanded exterior grade veneer core plywood, or phenolic resin particleboard Type 2-M-2 or 2-M-3. B. Hardboard: Exposed or semi-exposed, AHA A135.4, Class 1 tempered, smooth 2 sides. C. Plastic Edging: 1. Edge all Door and drawer fronts shall be edged with a nominal 3mm thick high impact PVC extrusion, with satin finish, machine applied with waterproof hot melt adhesive. 2. Edge all Horizontal and vertical front cabinet members with a flat edge 1mm thick high impact PVC extrusion, with a satin finish. 3. Barbed T-edging will not be acceptable. D. Plywood, Hardwoods: Solid lumber or plywood concealed members. Solid wood to be hardwood, kilndried, select Poplar, Fir, or mill option lumber, and plywood to be Baltic Birch 7-ply. 2.5 HARDWARE A. General: Manufacturer s standard, commercial-quality, heavy-duty hardware complying with BHMA A Use threaded metal or plastic inserts with machine screws for fastening to particleboard except where hardware is through-bolted from backside. Conform to requirements of ADAAG. MANUFACTURED CASEWORK
6 B. Hinges: Semi-concealed institutional 2-3/4, 5-knuckle, with interlaying leaves capable of 270 degree swing, nominal.090 inch minimum thickness steel, hospital-tipped with non-removable pins. One pair per door to 48 inch height, One and one-half pair over 48 inches in height. Brushed chrome, US26D. C. Pulls: Bent wire type, Brushed Chrome US26D finish, through fastened with machine screws. D. Drawer Guides: Zinc-plated steel channel, self-closing drawer guides, rebound-proof, positive in-stop and out-stop, epoxy-coated steel and nylon roller bearing slides with detent (to prevent rebound when drawers are closed, full or over-travel extension), full extension slides for file drawers, side or rail mounted, complying with BHMA A156.9, Type B05091, heavy duty (Grade 1HD-100 and Grade 1HD- 200) for the following loads: 1. Box Drawer Slides: 100 lbf up to 24 inches wide. 2. File Drawer Slides: 150 lbf up to 27 inches wide. 3. Lateral File Drawer: 200 lbf up to 42 inches wide. E. Adjustable Shelf Supports: Molded nylon or nickel, 2 pin, anti-lift, minimum 200-pound capacity support clip. F. Catches: Zinc plated or powder coated, nylon roller spring catch or dual, self-aligning, permanent magnet catch, meeting ADA requirements for pounds of pull required to open doors, two required for doors over 48 inches in height, positioned at top and bottom. Provide chain catch for tall units to allow doors to open 90 degrees minimum. Provide roller catches for mobile cabinets. G. Bumper Pads: Provide adhesive mounted felt or rubber bumper pads on drawer and door corners to eliminate noise of closing against cabinet body. H. Locks: Cylindrical (cam) type, 5 pin tumbler, brass with chrome plated finish, complying with BHMA A156.11, Grade Provide minimum of 2 keys per lock and 6 master keys. 2. Each room or area keyed alike unless otherwise indicated. 3. Provide locks as indicated on drawings. 4. Master key locks using the casework manufacturer s keying system. (Independent of the building master keying system.) 2.6 ACCESSORIES A. Support Members: Furniture grade, epoxy powder coated steel, with exposed welds ground smooth. 1. Steel Support Legs: 2 inch by 2 inch 12 gauge steel with welded top or side plate and 3/8 inch diameter leveler and non-rusting foot pad and leg shoe. 2. Angular Work Top Support: Factory welded 1-1/2 inch by 1/4 inch flat steel of vertical, horizontal, and angular design. 3. Cantilevered Work Top Support: 1-1/2 inch by 1-1/2 inch 12 gauge steel vertical, welded and ground smooth to 1-1/2 inch wide by 2-1/2 inch deep 12 gauge horizontal, with molded cap inserts at wall and countertop fastener holes. B. Leveling Guides: Threaded hydraulically operated glide with silicone putty.. C. Work Surfaces: Plastic Laminate countertop with grommets for cord access to receptacles and computer ports below. Place surface at height designated on drawings, with kneespace under and structural supports to floor. MANUFACTURED CASEWORK
7 2.7 CABINET FABRICATION A. General: 1. Comply with AWI Section 400 and its Division 400B "Laminate Clad Cabinets," Custom Grade, reveal overlay, 1/2-inch reveal dimension. 2. Finish exposed exterior and interior surfaces with high-pressure plastic laminate, unless otherwise indicated on Drawings. Fuse exterior surfaces to core using a minimum average high pressure of 360 PSI and average 300 degrees F. temperature. Bond interior surfaces and edges receiving laminate to substrate with Contact Adhesive. 3. Pre-drill all screw holes in factory to control accuracy. 4. Horizontal work surfaces: Solid 1 or 1-1/4 thick. 5. Machine parts for accurate fit and assemble with appropriate fastenings and adhesives to result in true, square, level, and plumb units. 6. Verify dimensions of other trades to be built into casework. 7. Provide removable or false backs for access or concealment of heating or plumbing items. 8. Scribe tops and backsplashes to walls and other adjoining vertical surfaces. 9. Provide a 1-1/2 inch maximum scribe with cabinets at end walls unless shown otherwise. 10. Filler Strips: Provide as needed to close spaces between cabinets and walls, ceilings, and indicated equipment. Fabricate from same material and with same finish as cabinets. B. Cabinet Bases: 4-inch high, water-repellent treated, 3/4-inch plywood or industrial grade particleboard. Recess base 3 at front and 1/4-inch at exposed ends. Provide additional center support for cabinets over 24 inches wide. C. Base, Wall, and Tall Cabinet Boxes: 1. Sides and top: Glued and spline-doweled 3/4-inch particleboard, balanced construction, surfaced with cabinet liner CL20 or melamine for semi-exposed locations and GP28 vertical grade laminate for exposed locations. 2. Bottom: 1 Particle Board. 3. Back Panel: Minimum 3/8-inch particleboard or 1/4-inch pre-finished tempered hard board, surfaced with cabinet liner CL20 or melamine for semi-exposed locations and GP28vertical grade laminate for exposed locations, inset and glued into sides, bottom, and top. 4. Exposed Backs: Constructed of 3/4-inch particleboard, surfaced with vertical grade laminate of balanced construction, glued and spline doweled, and mechanically attached if required. 5. Intermediate support rail: Minimum 3/4-inch particleboard, surfaced with GP28 vertical grade laminate of balanced construction, glued and doweled into cabinet sides. 6. Hanger rails: Two located at top and bottom of cabinet back, 3 on tall cabinets, locate at top, bottom, and center; 3/4 inch particleboard. 7. Clear inside depth of wall cabinets shall be 12 inches, minimum. D. Fixed and Adjustable Shelves: One-inch particleboard shelves, GP28 laminated plastic both sides. Color to match cabinet exterior. Edge front and back leading edges with flat 1mm thick high impact PVC edging to match shelf color. E. Adjustable Dividers: 1/4-inch minimum thickness, pre-finished tempered hardboard or plywood, smooth both faces, retained by molded plastic support clip. F. Fixed Dividers: 3/4-inch particleboard, surfaced with vertical grade laminate for exposed locations and cabinet liner CL20 or melamine for semi-exposed locations, glued and spline-doweled. PVC edged to match laminate or adjacent PVC edging. MANUFACTURED CASEWORK
8 G. Cabinet Doors: Reveal overlay style, 3/4-inch particleboard with GP28 high-pressure laminate exterior and CL20 cabinet liner interior surface. Provide 2 hinges per door for doors 48 inches and less in eight, and 3 hinges per door for doors over 48 inches in height. Provide square corners with radius edges, and PVC edging. H. Drawers: 3/4-inch particleboard fronts, 1/2 particleboard sides and backs, glued and doweled or dovetail jointed, all surfaced with GP28 laminate and CL20 cabinet liner on back, 1/4-inch tempered hardboard bottoms, fully captured, surfaced to match drawer sides, inset and glued to four sides. 1. File Drawers: Front-to-back and side-to-side hanger file capability with hanger channel for letter size files integral with file drawer sides, and removable steel channel to span side-to-side for legal size hanging files. I. Wall Shelving: Plastic-laminate sheet, Type HGL or HGP, shop bonded with waterproof glue to both sides of 1 inch particleboard. Finish both edges with rigid PVC extrusions, 3-mm thick. Provide Zincplated or powder-coated steel standards and shelf brackets, complying with BHMA A156.9, Types B04102 and B04112, surface mounted. 2.8 COUNTER TOPS AND SPLASHES A. Square Edge Configurations: 1 to 1-1/8 thick particleboard with 1-1/4 edge face including top and bottom laminates. Top and matching front edge to be GP50 plastic laminate factory bonded, continuous in practical lengths. Provide balancing sheet on opposite face. When requiring splice joints, use spines or dowels for alignment and tite-joint fasteners as required for a uniform and gapless joint. 1. Provide continuous top for counter cabinets fixed in a line. 2. Provide 4 high scribe-able, square set, and mechanically attached square-type backsplash with end splashes. Provide end splashes fitted to top. Provide backsplashes at all locations where countertops abut walls. 3. Provide one grommet hole and cover per 6-linear feet of countertop. Architect will field verify exact locations. 4. Provide support for cantilevered and unsupported spans greater than 30 inches in countertops. 5. Apply silicone sealant to joint between HPL top and backsplash. PART 3 EXECUTION 3.1 INSTALLATION A. General: 1. Strictly adhere to shop drawings and installation instructions furnished by the manufacturer. 2. Provide all connecting and attaching devices, closures, braces, supports, spacers, fillers and trim required for a finished installation. 3. Set casework properly in place, plumb and level, true to line. Shim as required, using concealed shims. 4. Where casework abuts other finish work, apply filler strips and scribe for accurate fit, with fasteners concealed where practical and scribed accurately. Provide concealed fastenings for cabinet cases, tops, splashes, and aprons. B. Base Cabinets: 1. Set cabinets straight, level, and plumb. Adjust sub-top within 1/16 inch of a single plane. Fasten cabinets to partition framing, wood blocking, or reinforcements in partitions with fasteners spaced 24 inches oc. 2. Bolt adjacent cabinets together with joints flush, tight, and uniform. MANUFACTURED CASEWORK
9 3. Align similar adjoining doors and drawers to a tolerance of 1/16 inch. C. Wall Cabinets: 1. Hang cabinet s straight, level, and plumb. Adjust fronts and bottoms within 1/16 inch of a single plane. Fasten to hanging strips, masonry, partition framing, blocking, or reinforcements in partitions. Align similar adjoining doors to a tolerance of 1/16 inch. 2. Fasten through back, near top and bottom, at ends, and not more than 16 inches o.c. with No. 10 wafer head screws sized for 1 inch penetration into wood blocking or hanging strips, or No. 10 wafer head sheet metal screws through metal backing or metal framing behind wall finish. D. Hardware: Install uniformly and precisely. Set hinges snug and flat in mortises. Adjust and align hardware so moving parts operate freely and contact point s meet accurately. Allow for final adjustment after installation. E. Tops and Backsplashes: 1. Secure top to cabinets with Z-type fasteners or equivalent, using 2 or more fasteners at each front, end, and back. 2. Abut top and edge surfaces in one true plane, with internal supports placed to prevent deflection. 3. Provide clear mildew resistant silicone sealant at top and around ends of countertops, endsplashes, and backsplashes where they meet wall surfaces. 4. Cut all openings in countertops for sinks or other items required. Cut to size from template furnished by supplier of sinks or use the designated sinks on job. 5. Field Jointing: Where possible make in the same manner as shop joining, using dowels, splines, adhesive, and fasteners recommended by manufacturer. Prepare edges to be joined in shop so project site processing of top and edge surfaces is not required. Locate field joints where shown on shop drawings. 6. Secure field joints with concealed clamping devices located within 6 inches of front and back edges and at intervals not exceeding 24 inches. Tighten according to manufacturer s written instructions to exert a constant, heavy clamping pressure at joints. 3.2 CLEANING AND ADJUSTMENT A. Adjust door catches, drawer slides, and other moving parts after installation for proper operation. B. Clean exposed surfaces, edges, and cabinet interiors and remove construction and installation marks prior to acceptance by Owner. C. Repair or remove and replace defective work as directed on completion of installation. D. Provide 6-mil plastic or other suitable water resistant covering over countertop surfaces taped to underside of countertop. Remove when directed by Architect. END OF SECTION MANUFACTURED CASEWORK
D. Product Certificates: Signed by manufacturers of casework certifying that products furnished comply with requirements.
SECTION 12356 - CASEWORK PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections,
More informationCaseworkUSA. specifications. 1.1 General 1.2 Summary. 1.3 Related Sections. 1.4 Definitions. 1.5 Qualifications and Quality Assurance
1.1 General 1.2 Summary A. This section includes the following Scope of Work as referred to in the plans: 1. Plastic laminate manufactured casework 2. Plastic laminate countertops 1.3 Related Sections
More informationSECTION MANUFACTURED CASEWORK
1 GENERAL 1.1 SECTION INCLUDES SECTION 12300 MANUFACTURED CASEWORK A. Work required to complete the manufactured casework indicated by the Contract Documents, and the items necessary for its proper installation.
More informationWHITE W/OAK TRIM NATURAL MEDIUM NORTHPORT OAK
WHITE W/OAK TRIM NATURAL MEDIUM NORTHPORT OAK Accessories. We believe that functionality is at the heart of any great kitchen. Above are a few of the accessories available with Merillat Essentials. The
More informationB. Shop Drawings: For residential casework. Include plans. elevations, details, and attachments to other work.
HVAC 1Sunporch 1Fire Alarm Renovation SECTION 123530 RESIDENTIAL CASEWORK PART 1 - GENERAL 1.1 SUMMARY A. Section includes laundry room cabinets. 1.2 ACTION SUBMITTALS A. Product Data: For each type of
More informationMusic Area Casework General 1.01 Summary Related Sections Definitions Qualifications and Quality Assurance
1.00 General 1.01 Summary Music Area Casework A. This section includes the following Scope of Work as referred to in the plans: 1. Thermally Fused Laminate manufactured casework, for use in music areas,
More informationAddendum. McKee and Associates Architecture and Interior Design. No. ONE Date: Project:
McKee and Associates Architecture and Interior Design Addendum No. ONE Date: 10.8.18 Project: A New Office for Gaston Elementary School for The Etowah County Board of Education Gadsden, Alabama A1.1 GENERAL
More informationA. Product Data: For each type of product indicated cabinet hardware and accessories, and finishing materials and processes.
SECTION 06402 - INTERIOR ARCHITECTURAL WOODWORK PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1
More informationSECTION PLASTIC LAMINATED CASEWORK
Specifications SECTION 123400 PLASTIC LAMINATED CASEWORK PART 1 GENERAL 1.01 SECTION INCLUDES This section provides the guidelines and standards for the manufacturing of plastic laminated casework and
More informationC. Installation shall be by experienced carpenters. Coordinate with plumbing and electrical contractors.
12300 - MANUFACTURED CASEWORK PART 1 - GENERAL 1.01 STIPULATIONS A. The specifications sections General Conditions, Special Requirements, and General Requirements form a part of this section by this reference
More informationSECTION ARCHITECTURAL WOOD CASEWORK
SECTION 06410 - ARCHITECTURAL WOOD CASEWORK PART 1 GENERAL 1.01 SECTION INCLUDES A. Wood cabinets for opaque finish. B. Flush wood paneling for transparent finish. C. Factory finishing. 1.02 RELATED REQUIREMENTS
More informationSECTION LAMINATE CLAD CASEWORK - COMMERCIAL
SECTION 123400 LAMINATE CLAD CASEWORK - COMMERCIAL PART 1 GENERAL 1.01 SECTION INCLUDES A. Fixed modular laminate clad casework and components. B. Flexible rail mounted laminate clad casework and components.
More informationSECTION CUSTOM CABINETS
PART 1 GENERAL 1.01 SECTION INCLUDES A. Specially fabricated cabinet units. B. Countertops. C. Cabinet hardware. D. Preparation for installing utilities. 1.02 RELATED REQUIREMENTS SECTION 06410 - A. Section
More informationADDENDUM TO THE CONTRACT. for the GLACIER FIRE STATION KITCHEN AND CLASSROOM RENOVATION. Contract No. E16-181
ADDENDUM TO THE CONTRACT for the ENGINEERING DEPARTMENT GLACIER FIRE STATION KITCHEN AND CLASSROOM RENOVATION Contract No. E6-8 ADDENDUM NO.: ONE CURRENT DEADLINE FOR BIDS: May 9, 206 PREVIOUS ADDENDA:
More information1. Division 6 Section "Rough Carpentry" for furring, blocking, and other carpentry work that is not exposed to view.
SECTION 06402 INTERIOR ARCHITECTURAL WOODWORK PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division 1 Specification
More informationStudent Services & Classroom Addition
SECTION 105116 - WOOD LOCKERS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections,
More informationA. This Section includes factory fabricated modular casework.
SECTION 12300 MODULAR CASEWORK PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division-1 Specification Sections,
More informationSECTION FINISH CARPENTRY PART 1 GENERAL. 1.1 SECTION INCLUDES A. Interior Finish Carpentry Work: 1. Refer to schedule at end of Section.
SECTION 06200 - FINISH CARPENTRY PART 1 GENERAL 1.1 SECTION INCLUDES A. Interior Finish Carpentry Work: 1. Refer to schedule at end of Section. 1.2 RELATED SECTIONS A. Section 06100 - Rough Carpentry:
More informationSECTION INTERIOR ARCHITECTURAL WOODWORK
SECTION 06 40 23 INTERIOR ARCHITECTURAL WOODWORK PART 1 GENERAL 1.01 SECTION INCLUDES A. Laminate clad cabinets and custom components. B. Laminate clad countertops. C. Cabinet hardware including countertop
More informationSECTION INTERIOR ARCHITECTURAL WOODWORK. A. Section includes interior woodwork items indicated not specified elsewhere and as specified.
SECTION 06 40 23 INTERIOR ARCHITECTURAL WOODWORK PART 1 - GENERAL 1.1 SUMMARY A. Section includes interior woodwork items indicated not specified elsewhere and as specified. B. Options: 1. Where casework
More informationSCI-FAB Product Specifications. Casework Section 1. Part 1 General
SCI-FAB Product Specifications Casework Section 1 Part 1 General 1.1 SCOPE OF WORK Includes all factory fabricated stainless steel casework as required by the project drawings. 1.2 TYPICAL INCLUSIONS A.
More informationSECTION CUSTOM CASEWORK
PART 1 GENERAL 1.1 SECTION INCLUDES SECTION 06 41 00 CUSTOM CASEWORK A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division 1 specification sections,
More information***************************************************************************************************************
06400 ARCHITECTURAL WOODWORK SPECIFIER: CSI MasterFormat 2004 number 06 40 00 PART 1 GENERAL 1.1 SUMMARY A. Provide necessary services, tools, equipment, material, and labor required to furnish and install
More informationB. American Society for Testing and Materials (ASTM):
SECTION 06400 ARCHITECTURAL WOODWORK PART 1 GENERAL 1.01 SUMMARY A. Provide necessary services, tools, equipment, material, and labor required to furnish and install millwork and cabinet work. Install
More informationROWAN COUNTY AIRPORT APRIL 2017 TERMINAL EXPANSION
SECTION 12300 - MANUFACTURED CASEWORK PART 1 - GENERAL RELATED DOCUMENTS: Drawings, General Conditions and Supplementary General Conditions and other Division-1 Specification Sections, apply to this Section.
More informationSECTION ARCHITECTURAL WOODWORK
SECTION 06400 ARCHITECTURAL WOODWORK PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Custom Cabinet Units a. Plastic Laminate b. Sound Barrier for Casework 2. Cabinet Hardware B. Related Sections:
More informationSECTION ARCHITECTURAL WOODWORK. B. Related Sections: 1. Section Paints and Coatings: Field applied painted finishes.
PART 1 - GENERAL 1.1 SUMMARY SECTION 06 40 00 A. Provide architectural woodwork as shown and specified. Work includes: 1. Providing plastic laminate finished casework. 2. Providing plastic laminate clad
More informationCascade Ph: Casework Fax: Corp
Cascade Ph: 541-928-3750 Casework Fax: 541-928-3880 Corp email: bill.yates@cascase.com Cascade Casework Corp SPECIFICATIONS FOR PLASTIC LAMINATE FACED CASEWORK Specifications Section 12300 Section 06400
More informationDIVISION 11 EQUIPMENT SECTION PHOTO DARKROOM CASEWORK
DIVISION 11 EQUIPMENT SECTION PHOTO DARKROOM CASEWORK PART 1 GENERAL 1.01 Scope of Work A. Provide material, accessories, tools, equipment and labor as required for the complete fabrication and installation
More informationB. Section Rough Carpentry: Support framing, grounds, and concealed blocking.
SECTION 06 41 00 - ARCHITECTURAL WOOD CASEWORK PART 1: GENERAL 1.1 SECTION INCLUDES A. Specially fabricated cabinet units. B. Cabinet hardware. C. Factory finishing. 1.2 RELATED REQUIREMENTS A. Division
More informationContents. E-Line Series (Wood Casework) K-Line Series (Wood Casework) D-Line Series (Wood Casework)
WOOD CABINET LINES Contents E-Line Series (Wood Casework)... 2-3 K-Line Series (Wood Casework)... 4-5 D-Line Series (Wood Casework)... 6-7 L-Line Series (Wood Casework)... 8-9 M-Line Series (MDF Casework)...
More informationSECTION PLASTIC-LAMINATE-FACED ARCHITECTURAL CABINETS AND COUNTERTOPS
SECTION 06 41 16 - CABINETS AND COUNTERTOPS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationSECTION INTERIOR ARCHITECTURAL WOODWORK
SECTION 064023 INTERIOR ARCHITECTURAL WOODWORK PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Plastic-laminate cabinets. 2. Plastic-laminate countertops. 3. Plastic-laminate window sills. 4. Cabinet
More informationSECTION WOOD ARCHITECTURAL CABINETS AND LAMINATE COUNTERTOPS
SECTION 064113- WOOD ARCHITECTURAL CABINETS AND LAMINATE COUNTERTOPS PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions
More informationNATURAL TOFFEE SABLE SEDONA KONA SENECA RIDGE MAPLE
NATURAL TOFFEE SABLE SEDONA KONA SENECA RIDGE MAPLE Framed Door Styles Traditional Overlay Raised Panel Wood veneered raised panel doors feature concealed nickel-finished self-closing hinges. Drawer fronts
More informationSPECIFICATIONS: Red Oak Veneer Casework as manufactured by Mastercraft Woodworking Co., Inc.
SPECIFICATIONS: Red Oak Veneer Casework as manufactured by Mastercraft Woodworking Co., Inc. These specifications contain certain optional selections, which must be made by the specification developer.
More informationSECTION PLASTIC-LAMINATE-FACED ARCHITECTURAL CABINETS
SECTION 064116 - PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Plastic-laminate-faced architectural cabinets. 2. Wood furring, blocking, shims, and hanging strips for installing plastic-laminatefaced
More informationChevy Chase Club June 30, 2008 Bowie Gridley Architects
SECTION 081433 - STILE AND RAIL WOOD DOORS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationAMPCO PRODUCTS, INC. TECHNICAL SPECIFICATIONS SOLID PHENOLIC CORE TOILET COMPARTMENTS
PART 1 - GENERAL 1.1 RELATED DOCUMENTS TECHNICAL SPECIFICATIONS SOLID PHENOLIC CORE TOILET COMPARTMENTS A. Drawings and General Provisions of Contract, including General and Supplementary Conditions and
More informationDIVISON 6 WOODS AND PLASTICS SECTION PLASTIC LAMINATE FACED ARCHITECTUAL CABINETS
DIVISON 6 WOODS AND PLASTICS PART 1 - GENERAL 1:1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationSECTION ARCHITECTURAL WOOD CASEWORK
PART 1 GENERAL 1.01 SECTION INCLUDES A. Specially fabricated cabinet units. B. Countertops. C. Cabinet hardware. D. Factory finishing. E. Preparation for installing utilities. 1.02 SUBMITTALS SECTION 06
More informationSECTION PRE-MANUFACTURED CABINETS
SECTION 12390 PRE-MANUFACTURED PART 1 GENERAL 1.1 DESCRIPTION OF WORK A. The work includes furnishing all labor, materials and equipment required to complete the Pre-Manufactured Cabinet work as shown
More informationSection "Rough Carpentry" for wood blocking for anchoring laboratory casework.
SECTION 1235519 - PART 1 - GENERAL 1 RELATED DOCUMENTS Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this
More informationSECTION WOOD ARCHITECTURAL CABINETS AND QUARTZ COUNTERTOPS
SECTION 064113- WOOD ARCHITECTURAL CABINETS AND QUARTZ COUNTERTOPS PART 1- GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions
More informationMASTERSPEC TECHNICAL SPECIFICATIONS DIVISION 06 WOOD, PLASTICS AND COMPOSITES
SECTION 064023 - INTERIOR ARCHITECTURAL WOODWORK PART 1 - GENERAL 1.1 SUMMARY A. This Section includes the following: 1. Interior standing and running trim. 2. Interior frames and jambs. 3. Stairwork and
More informationCopyright 2017 AIA MasterSpec Premium 05/17 PRODUCT MASTERSPEC LICENSED BY ARCOM TO WEREVER PRODUCTS, INC.
This Product MasterSpec Section is licensed by ARCOM to Werever Products, Inc. ("Licensee"). This proprietary Product MasterSpec Section uses modified original MasterSpec text. Revisions made to the original
More informationProduct Guide Specification
RYNONE March 2, 2011 North Thomas Avenue, PO Box 128, Sayre, Pennsylvania 18840 P: (570) 888-5272 F: (570) 888-1175 W: www.rynone.com Product Guide Specification Specifier Note: This product guide specification
More informationSECTION INTERIOR FINISH CARPENTRY PART 1 - GENERAL 1.1 RELATED DOCUMENTS
SECTION 062023 - INTERIOR FINISH CARPENTRY PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationPlastic Laminate Casework
Plastic Laminate Casework Casework Contents Cover Letter... 3 Specifications... 4-13 Cabinet Construction... 14-27 Hardware... 28-38 Base Cabinets... 29-63 Tall Cabinets... 64-88 Wall Cabinets... 89-116
More information5120 BAND AND MUSIC. Specifications STEVENS ADVANTAGE 5120 BAND AND MUSIC SECTION ADVANTAGE furnishings PART 1 GENERAL
STEVENS 5120 BAND AND MUSIC SECTION - 12400 PART 1 GENERAL 1.01 GENERAL PROVISIONS A. Applicable provisions of General Conditions, Special Conditions and General Requirements shall apply to this section
More informationDIVISION 12 - FURNISHINGS. Section General Discussion. Introduction
Section 12000 - General Discussion This General Discussion Section contains material which is important to the successful fabrication and/or installation of furnishings and equipment in construction projects.
More informationWELLNESS CENTER REMODEL UNIVERSITY OF CALIFORNIA, MERCED MERCED, CALIFORNIA PROJECT NO.: 907432 C. Solid Surfacing Material: 1. Manufacturers: D. Wood: a. First Floor; Wilsonart International, Solid Surfaces,
More informationTender No Section St. James - Assiniboia Centennial Pool Fitness Facility Addition Page 1
Fitness Facility Addition Page 1 PART 1 GENERAL 1.1 SECTION INCLUDES.1 Finish carpentry items including shop prefabricated casework and countertops..2 Hardware and attachment accessories..3 Wood Benches..4
More informationArchitectural Woodwork Standards. casework. s e c t i o n
Architectural Woodwork Standards casework s e c t i o n SECTION Introductory INFORMATION Guide Specifications...284 Introduction...285 Categories...285 Wood...285 Decorative Laminate...285 Solid Phenolic...285
More informationModular Laminate Casework Specifications
Modular Laminate Casework Specifications Labscape Modular Laminate Specifications 1.01 GENERAL PROVISIONS A. Applicable provisions of General Conditions, Special Conditions, and General Requirements shall
More informationB. Shop Drawings: For horizontal louver blinds, include fabrication and installation details.
HIGGINSVILLE HABILITATION CENTER MISC. BUILDING RENOVATIONS STATE OF MISSOURI HIGGINSVILLE, MISSOURI SECTION 122113- HORIZONTAL LOUVER BLINDS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general
More informationA. All trim that has been damages, broken, or missing shall be repaired or replaced with material of the same size, shape, and type.
SECTION 062000 - FINISH CARPENTRY PART 1 - GENERAL 1.1 SECTION REQUIREMENTS A. All trim that has been damages, broken, or missing shall be repaired or replaced with material of the same size, shape, and
More informationSECTION INTERIOR ARCHITECTURAL WOODWORK
SECTION 06402 - INTERIOR ARCHITECTURAL WOODWORK PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1
More informationSECTION LABORATORY CASEWORK AND EQUIPMENT
PART 1 GENERAL 1.1 RELATED DOCUMENTS SECTION 12 35 53 LABORATORY CASEWORK AND EQUIPMENT A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1
More informationSECTION INTERIOR FINISH CARPENTRY
SECTION 06 20 23 PART 1 - GENERAL 1.01 SUMMARY A. Section includes the following items for field-applied paint finish: 1. Interior standing and running trim. 2. Interior plywood paneling. B. Related Sections
More informationSECTION 12345.1 - MODULAR STEEL LABORATORY CASEWORK 1 PART 1 PRODUCTS 1.01 MANUFACTURER A. Casework and equipment manufacturer: ALIR Systems, Inc., 245 Harrison St, Jamestown, New York, 14701. 1.02 CASEWORK
More information3100 PLYCORE SPECIFICATIONS. Square edge. ADVANTAGE furnishing s Plycore. Specifications
Square edge 3100 PLYCORE SPECIFICATIONS ADVANTAGE furnishing s 3100 Plycore Specifications 217.540.3100 www.stevensind.com 3100 PLYCORE STEVENS ADVANTAGE 3100 PLYCORE SECTION - 12400 PART 1 GENERAL 1.01
More informationHARDWARE and PRODUCT SPECIFICATIONS ANTIMICROBIAL CASEWORK
HARDWARE and PRODUCT SPECIFICATIONS ANTIMICROBIAL CASEWORK HARDWARE SPECIFICATION KEY 1. DOOR/DRAWER PULLS 2. HINGES 3. DRAWER SLIDES 3A. DRAWER SLIDES 3B. FILE DRAWER SLIDES 4. LOCKS 4A. DRAWER LOCKS
More informationSECTION CUSTOM MILLWORK
PRT 1 GENERL 1.01 SECTION INCLUDES SECTION 06 41 00 Shop-fabricated plastic laminate-clad cabinet units. B. Countertops. C. Cabinet hardware. 1.02 SUBMITTLS See Section 01 30 00 -dministrative Requirements,
More informationA. This Section includes interior architectural woodwork items indicated on Drawings and specified in this Section.
SECTION 064023 - INTERIOR ARCHITECTURAL WOODWORK PART 1 - GENERAL 1.1 SUMMARY A. This Section includes interior architectural woodwork items indicated on Drawings and specified in this Section. 1.2 DEFINITIONS
More informationA. Boards or Strips: Lumber of less than 2 inches nominal size in least dimension.
HIGGINSVILLE HABILITATION CENTER MISC. BUILDING RENOVATIONS STATE OF MISSOURI HIGGINSVILLE, MISSOURI SECTION 061000 - ROUGH CARPENTRY PART 1 -GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions
More informationWood Casework Construction Details
CASEWORK CONSTRUCTION DETAILS Overview Cabinets Mott casewk can meet the most demanding specification, whether it is AWI Premium an architect's 'signature' specification. We manufacture using premium grade
More informationDesign and Construction Standards SECTION ATHLETIC LOCKERS
SECTION 10505 ATHLETIC LOCKERS PART 1 GENERAL 1.1 RELATED DOCUMENTS A. The provisions of the General Conditions, Supplementary Conditions, and the Sections included under Division 1, General Requirements,
More informationCoordinate installation of rough carpentry members specified in other sections.
1 1.03 Preservative treated wood materials. Concealed wood blocking, nailers, and C. Miscellaneous wood nailers, furring, and grounds. PART2 2.01 See Section 01 30 00 =Administrative Requirements, for
More informationSECTION FINISH CARPENTRY. A. PART A and DIVISION 1 of PART B are hereby made a part of this SECTION.
SECTION 062000 PART 1 GENERAL 1.01 GENERAL REQUIREMENTS A. PART A and DIVISION 1 of PART B are hereby made a part of this SECTION. B. Examine all conditions as they exist at the project prior to submitting
More informationDIVISION 6 WOOD, PLASTICS AND COMPOSITES
DIVISION 6 WOOD, PLASTICS AND COMPOSITES PART 1 GENERAL 1.01 SECTION INCLUDES SECTION 06 1000 ROUGH CARPENTRY A. Rough opening framing for doors, windows, and roof openings. B. Roofing nailers. C. Preservative
More informationSECTION WOOD DOORS
SECTION 08211 WOOD DOORS Notice to Vendors: CANV prefers to purchase products that contain tropical wood only if they are certified according to the guidelines of the Forest Stewardship Council (FSC).
More information3600 PLYCORE-V SPECIFICATIONS. Wood finish veneer. ADVANTAGE furnishing s Plycore-V. Specifications
Wood finish veneer 3600 PLYCORE-V SPECIFICATIONS ADVANTAGE furnishing s 3600 Plycore-V Specifications 217.540.3100 www.stevensind.com 3600 PLYCORE-V STEVENS ADVANTAGE 3600 PLYCORE-V SECTION - 12400 PART
More informationSECTION CARPENTRY
SECTION 06100 CARPENTRY PART 1 GENERAL 1.01 SUMMARY A. Section Includes: Carpentry work including grounds, nailers, blocking, miscellaneous framing, plywood backing panels, plywood sheathing, preservative
More informationMASTERSPEC TECHNICAL SPECIFICATIONS DIVISION 08 - OPENINGS
SECTION 081433 - STILE AND RAIL WOOD DOORS PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Exterior stile and rail wood doors and sidelites. 2. Interior stile and rail wood doors. 3. Interior fire-rated,
More informationDIVISION 6 WOODS AND PLASTICS SECTION FINISH CARPENTRY
DIVISION 6 WOODS AND PLASTICS SECTION 06 20 23 PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01
More informationA. Provide all finish carpentry needed for a complete and proper installation.
SECTION 06200 - PART ONE GENERAL 1.1 SECTION INCLUDES A. Provide all finish carpentry needed for a complete and proper installation. B. Provide all wood, nails, bolts, screws, and all other items needed
More informationSECTION MISCELLANEOUS ROUGH CARPENTRY
SECTION 06 1053 - MISCELLANEOUS ROUGH CARPENTRY PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01
More information.1 Comply with the General Conditions of the Contract, Supplementary General Conditions and the requirements of Division 1.
PAGE 1 PART 1 GENERAL 1.1 REFERENCE.1 Comply with the General Conditions of the Contract, Supplementary General Conditions and the requirements of Division 1. 1.2 RELATED WORK SPECIFIED ELSEWHERE.1 Rough
More informationA. Dimension Lumber: Lumber of 2 inches nominal or greater but less than 5 inches nominal in least dimension.
SECTION 06 10 53 - MISCELLANEOUS ROUGH CARPENTRY PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01
More informationADDENDUM TO BID DOCUMENTS ADDENDUM #03 SCCD RFP: # Project: Solano Community College District Vacaville Classroom Building (Annex) Renovation
Vacaville Classroom Annex Renovation Documents #18-005 ADDENDUM TO BID DOCUMENTS ADDENDUM #03 SCCD RFP: #18 005 Project: Vacaville Classroom Building (Annex) Renovation Date: 11/22/2017 Addendum # 03 The
More informationSECTION INTERIOR FINISH CARPENTRY. A. Lumber grading agencies, and the abbreviations used to reference them, include the following:
SECTION 06 2023 PART 1 GENERAL 1.1 SUMMARY A. This Section includes the following: 1. Interior standing and running trim. 2. Interior stairs. 1.2 DEFINITIONS A. Lumber grading agencies, and the abbreviations
More informationBovard Studios Inc. Section April 6, 2004 Page 1
April 6, 2004 Page 1 This section includes solid flush and surface articulated wood doors, may have veneer facing, solid or glazed (stained glass) design, factory pre-fit, may be factory finished or site
More informationSECTION FINISH CARPENTRY
PART 1 - GENERAL 1.1 DESCRIPTION SECTION 06 20 00 1. Use this section only for NCA projects. 2. Delete between // // if not applicable to project. Also delete any other item or paragraph not applicable
More informationC. Samples for Initial Selection: Manufacturer's color charts showing the full range of colors available.
SECTION 105113 - METAL LOCKERS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationRIVERSIDE MEDICAL CENTER 5/09
SECTION 06200 - FINISH CARPENTRY PART 1 - GENERAL 1.01 DESCRIPTION: A. Work of this section is subject to requirements of the Contract Documents including the General Conditions and Supplementary Conditions
More informationA. Work of this Section, as shown or specified, shall be in accordance with the requirements of the Contract Documents.
Section 06400 Page 1 Section 06400 ARCHITECTURAL WOODWORK PART 1 GENERAL 1.1 GENERAL REQUIREMENTS A. Work of this Section, as shown or specified, shall be in accordance with the requirements of the Contract
More informationADDENDUM NO. 1 THOROUGHBRED ROOM RENOVATION PHASE II DINING AREA MURRAY STATE UNIVERSITY, MURRAY, KY PROJECT #
ADDENDUM NO. 1 THOROUGHBRED ROOM RENOVATION PHASE II DINING AREA MURRAY STATE UNIVERSITY, MURRAY, KY PROJECT #13-046 10-23-2013 Bidders shall acknowledge receipt of this Addendum on the Bid Form, in the
More informationB. Related Requirements: 1. Section "Interior Painting" for priming and backpriming of interior finish carpentry.
1 ~GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this Section. 1.2 SUMMARY
More informationAsh Brook Golf Course Scotch Plains, New Jersey
SECTION 062013 - EXTERIOR FINISH CARPENTRY PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationProduct Guide Specification
Shield Casework February 2014 3421 Merriam Lane Overland Park, Kansas 66203 Phone 913-744-2183 Fax 913-384-3477 Website www.shieldcasework.com E-mail info@shieldcasework.com Product Guide Specification
More informationAlexandra Secondary College Refurbishment Project No: 1507 SECTION MANUFACTURED CASEWORK - SHOP BUILT 12300/1
SECTION 12300 MANUFACTURED CASEWORK - SHOP BUILT 12300/1 PART I GENERAL 101 Scope The work of this Section covers the supply and installation of manufactured casework items. It includes but is not limited
More informationSECTION BULLET- RESISTANT DOORS
1 SECTION 08 3950 BULLET- RESISTANT DOORS PART 1- GENERAL 1.01 SUMMARY A. This Section Includes: 1. Bullet- resistant steel door and frame systems. 2. Door hardware for bullet- resistant steel door and
More informationSECTION INTERIOR ARCHITECTURAL WOODWORK
SECTION 064023 PART 1 - GENERAL 1.1 SUMMARY This Section includes the following: 1. Architectural wood casework: a. Plastic-laminate-faced cabinets. b. Wood-veneer-faced cabinets. 2. Countertops: a. Solid-surfacing
More informationJan H: ARCHITECTURAL WOODWORK (06410-H)
2101 Commonwealth Blvd, Suite B Ann Arbor, MI 48105-5759 www.med.umich.edu/facilities/plan/ 064040-H: ARCHITECTURAL WOODWORK (06410-H) GENERAL In general, follow the guidelines below when designing and
More informationProduct Guide Specification For Nonrated & 20-Minute Rated Doors
Woodtech Trading Company 455 Fourth Avenue E.N. P.O. Box 2609 Columbia Falls, MT 59912 800-775-1352 (phone) 800-775-1353 (fax) www.woodtechdoor.com Product Guide Specification For Nonrated & 20-Minute
More informationSection Rough Carpentry
Section 06 10 00 Rough Carpentry 06 10 00-1 PART 1 - GENERAL 1.01 SECTION INCLUDES A. Blocking in wall and roof openings; wood furring and grounds; electrical panel back boards, concealed wood blocking.
More informationSECTION INTERIOR ARCHITECTURAL WOODWORK
LSE ARCHITECTS, INC. LSE: 14.1001.01 SEWARD MONTESSORI SCHOOL ADDITION & REMODELING SECTION 06 40 23 PART 1 - GENERAL 1.01 SUMMARY A. Section Includes 1. Plastic-laminate clad cabinets and countertops.
More information1. Division 6: Rough carpentry, blocking within walls to adequately support casework. 2. Division 9: Furnishing and installation of base molding.
SECTION 12 32 00 - WOOD LABORATORY CASEWORK PART 1: GENERAL 1.1 SUMMARY A. Section Includes: 1. Wood Casework. Furnish all cabinets and casework, including tops, ledges, supporting structures, and miscellaneous
More informationSECTION FINISH CARPENTRY
SECTION 06200 - PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections, apply to
More information