SECTION ARCHITECTURAL WOODWORK. B. Related Sections: 1. Section Paints and Coatings: Field applied painted finishes.

Size: px
Start display at page:

Download "SECTION ARCHITECTURAL WOODWORK. B. Related Sections: 1. Section Paints and Coatings: Field applied painted finishes."

Transcription

1 PART 1 - GENERAL 1.1 SUMMARY SECTION A. Provide architectural woodwork as shown and specified. Work includes: 1. Providing plastic laminate finished casework. 2. Providing plastic laminate clad countertops and trim. 3. Providing standing and running wood trim. 4. Installing wood doors furnished under Section Installing door hardware furnished under Section B. Related Sections: 1. Section Paints and Coatings: Field applied painted finishes. 1.2 REFERENCES A. Reference standards: 1. American National Standards Institute (ANSI): a. ANSI A115 Series "Door and Frame Preparation for Hardware." b. ANSI A Particleboard 2. Architectural Woodwork Institute (AWI): a. AWI 2003 "Architectural Woodwork Quality Standards, 8th Edition, Version 1.0." b. AWI Section 100 "Lumber." c. AWI Section 200 "Panel Products." d. AWI Section 300 "Standing & Running Trim" e. AWI Section 400B "Architectural Cabinets (Laminate Clad Cabinets)." f. AWI Section 400C "Architectural Cabinets (Tops)." g. AWI Section 500 "Paneling & Related Wood Doors." h. AWI Section 1500 "Factory Finishing" i. AWI Section 1700 "Installation" 3. National Electrical Manufacturers Association (NEMA): a. NEMA LD "High-Pressure Decorative Laminates, Part 1-4." 4. National Institute of Standards and Technology (NIST) Product Standards: a. NIST PS 1-95 "Construction and Industrial Plywood." b. NIST PS "American Softwood and Lumber Standard." 1.3 DEFINITIONS A. Exposed Surfaces: Casework surfaces visible after installation with doors and drawers closed. Other locations considered to be exposed include wall hung casework bottoms more than 40 inches above the floor and visible members in open cases or behind clear glass doors. B. Semi-Exposed Surfaces: Casework members behind opaque doors, including shelves, divisions, interior faces of ends, case backs, drawer sides, backs and bottoms and back face of doors. Tops of cases 6'-6" or more above the floor shall be considered semi-exposed. C. Concealed Surfaces: Sleepers, web frames, dust panels and other surfaces not usually visible after installation

2 1.4 SUBMITTALS A. Submit shop drawings for casework, countertops, paneling and trim. 1. Provide large scale details. Indicate materials, component profiles, fastening and jointing details, hardware, finishes and accessories. 2. Show relationship to adjacent work. Indicate countertop methods of edging and location and construction of joints. 3. Provide manufacturer's product data for hardware, accessory and specialty items. B. Submit samples of the following: 1. Plastic laminate manufacturers full color range of plastic laminate samples for color selection. 2. Submit one sample of each type of casework hardware for review and approval. Accepted samples will be returned to the Contractor. Accepted samples may be used in the work. C. Submit product certificates signed by the woodwork fabricator certifying products comply with specified requirements. D. Submit manufacturer's maintenance data for plastic laminate products. Include a list of approved cleaning materials and recommended cleaning procedures. Provide instructions for stain removal and surface finish restoration. 1.5 QUALITY ASSURANCE A. Architectural woodwork fabricators qualifications: A firm specializing in the fabrication of architectural woodwork with a satisfactory record of performance on projects of comparable size and quality. Fabricator shall be acceptable to the Architect/Engineer. B. Installation: Performed only by the architectural woodwork fabricator or experienced skilled finish carpenters approved by the fabricator and acceptable to the Architect/Engineer. C. Quality Standards: Comply with AWI 2003 "Architectural Woodwork Quality Standards, 8th Edition, Version 1.0." except as otherwise indicated. D. Provide lumber and plywood factory grade-marked on concealed surfaces. Omit marking and submit mill certificates for materials that cannot be marked on a concealed surface. E. Pre-installation meeting: Meet at project site before delivery of architectural woodwork and review coordination and controls required for proper installation in areas to receive work. Include in meeting the Contractor, Architect/Engineer, installers of millwork, other finishes, painting, and when applicable mechanical and electrical work. 1.6 DELIVERY, STORAGE AND HANDLING A. Protect architectural woodwork materials during delivery, storage and handling to prevent damage, soiling and deterioration. B. Do not deliver architectural woodwork materials until concrete, masonry and other similar wet work has been completed and is thoroughly dry, outside door and window openings are permanently watertight, and, in case of temperature dropping below 60 degrees F, until temporary heating and ventilating systems are in operation. C. Store materials in dry well-ventilated spaces with constant minimum temperature of 60 degrees F and maximum relative humidity of 55 percent

3 1.7 PROJECT CONDITIONS A. Provide and maintain a constant temperature and humidity before, during and after installation as required to maintain optimum moisture content of installed materials. B. Field Measurements: Where architectural woodwork items are indicated to be fitted to other construction, verify dimensions of other construction by accurate field measurements before manufacturing architectural woodwork; show recorded measurements on final shop drawings. Coordinate manufacturing schedule with construction progress to avoid delay of Work. PART 2 - PRODUCTS 2.1 GENERAL A. Materials used in finished work shall be clear, free of cracks, checks, knots, and other imperfections that may interfere with proper completion of the work. Warped or otherwise imperfect work shall be removed and replaced by responsible Contractor. B. Lumber and panel product materials: Comply with AWI Quality Standards. 1. Section 100: Lumber. 2. Section 200: Panel Products. C. Provide lumber surfaced four sides (S4S) and worked to profiles and patterns shown. Nominal sizes are as shown, except where detailed dimensions are indicated. D. Moisture content: Provide materials kiln-dried to moisture content complying with AWI Standards, Section 100-S-11. E. Hardwood lumber: Comply with National Hardwood Lumber Association (NHLA) "Rules for Measurement and Inspection of Hardwood Lumber and Cypress." F. Softwood lumber: Comply with PS-20 "American Softwood and Lumber Standard" and with applicable grading rules of grading and inspection agency for species indicated. 1. Douglas Fir, Western Red Cedar, Ponderosa Pine, White Pine: Western Lumber Grading Rules, 91 published by Western Wood Products Association (WWPA), or Standard Grading Rules, No. 16, 1989, published by West Coast Lumber Inspection Bureau (WCLIB). G. Plywood: Provide each softwood plywood panel grade-trademarked, identifying type, grade and conformance with NIST Product Standard PS 1 for Construction and Industrial Plywood. 1. Thickness and application details as shown on the drawings. H. Particleboard: Comply with ANSI A208.1 "Particleboard, Mat-Formed Wood." I. Plastic laminate: Comply with NEMA Publication No. LD3 "High-Pressure Decorative Laminates, Part 1-4" requirements for high-pressure laminated materials. 1. Plastic laminate: Formica Corp., "Formica" or an Architect/Engineer approved equal by Nevamar Corp., Pioneer Plastics Corp., or Wilsonart International. Satin finish, color selected by Architect/Engineer based on manufacturer's full line of solid colors and patterns. J. Cabinet construction: Comply with AWI Section 400C and AWI publication "Architectural Casework Details" for Custom Grade architectural woodwork. K. Paneling construction: Comply with AWI Section

4 L. Factory finishing: Comply with AWI Section 1500 and publication "Factory Finishing of Architectural Woodwork." M. Hardware preparation: Comply with ANSI A115 Series "Specifications for Door and Frame Preparation for Hardware." N. Fasteners: Provide fastener type, size, material and finish as required by conditions of use, substrate material and adequate anchorage for the work. O. Cast Plastic - Solid surface materials: DuPont Corian Corian or an Architect/Engineer approved equal integrally colored solid surface, non-porous, homogenous polyester and acrylic components with filler by Formica Corp. "Surell", Nevamar Decorative Surfaces "Fountainhead" or Wilsonart International Gibraltar. 2.2 MATERIALS A. Plastic laminate countertops and trim: AWI Custom Grade, Section 400C. 1. Face sheets: General purpose grade, GP50, minimum.050" thick. 2. Cores: Minimum 3/4" thick 5-ply exterior grade hardwood faced plywood or ANSI A208.1 phenolic resin particleboard type 2-M-2 or 2-M Adhesive: AWI 100-S-5 Type I waterproof type as recommended by plastic laminate manufacturer. 4. Color and Finish: As selected by the Architect/Engineer. 5. Joint sealants: One-component silicone rubber elastomeric sealant complying with Section requirements, color matched to plastic laminate color. 2.3 CAST RESIN PANELS A. Cast Resin, Lumicor: high performance resins, including acrylic, coss-linked acrylic. 1. Lumicor Tiki Grass or Design Tex Tiki Stalk 2. Cross Linked Acrylic ¼ thickness 3. Matte Finish 4. Fire Rating ASTM D Smoke Density ASTM D Rate of Ignition ASTM D STANDING AND RUNNING TRIM A. Standing and running trim and plywood paneling, site applied transparent stained finish: AWI Custom Grade, Section 300, Clear plain sawn Oak hardwood, sizes and profiles shown. 1. Install standing and running trim 2.5 PLASTIC LAMINATE CASEWORK A. Plastic Laminate Clad Casework: AWI Sections 400, Custom grade. 1. Casework Construction: Flush overlay design. 2. Casework Bodies, Countertops and Splashes: High pressure plastic laminate and cabinet liner on particle board, minimum 3/4 inch thick except where otherwise indicated. Provide exterior grade plywood instead of particle board for countertops and backsplashes with sinks. 3. Casework Shelving: Cabinet liner on particle board, except provide high pressure plastic laminate matching casework at open cases. Finish four edges, top and bottom face of shelves in open cases. a. Shelving under 30 inches wide: 3/4 inch thick. b. Shelving over 30 inches wide: 1 inch thick. c. Adjustable shelving standards: Metal, recessed flush with applicable clips. 4. Concealed Framing: Sound material of any species. 5. Casework Backs: Melamine on particle board, minimum 1/4 inch thick

5 6. Drawer Bottoms, Sides, Backs and Semi-Exposed Fronts: Melamine on particle board, minimum 1/2 inch thick with color matched PVC edging. 7. Casework Doors and Drawer Fronts: High pressure plastic laminate and casework liner on particle board. a. Doors 30 inches wide x 60 inches high or smaller: 3/4 inch thick. b. Larger doors to a maximum of 36 inches wide x 72 inches high: 1 inch thick. 8. Wood Cleats: Hardwood, used with wall supported shelves or countertops. 9. Edge Treatment: PVC or same laminate as horizontal surfaces. 10. Wall cabinets shall have exposed bottoms finished to match face material and color when bottom is 40 inches above floor line. B. Finishes and Laminates: 1. Laminate Cladding Colors, Patterns, Finishes: As selected by the Architect. 2. Exposed Surfaces: General Purpose inch high pressure plastic laminate including four edges and back face of doors and applied drawer faces. 3. Semi-Exposed Surfaces: Except as otherwise indicated, provide melamine on particle board. 4. Provide inch phenolic backing sheet to underside of plastic laminate faced countertops and exposed particle board edges of all cutouts for sinks and to concealed backsplash faces which are not an integral part of the casework unit and are adhered to the wall. 5. Concealed surfaces require no laminate finish unless specifically noted otherwise. C. Casework hardware: 1. Finish: US32D, satin stainless steel finish, unless otherwise indicated. 2. Hinges: Julius Blum Inc., Stanley, NC (800) Maxus Institutional Hinges, concealed 170 degree swing. a. Subject to compliance with specified requirements, the following manufacturers are acceptable: 1) Grass America, Kernersville, NC (800) ) Hafele America, Archdale, NC (800) ) Mepla Inc., High Point, NC (800) Pulls: Wire pulls, 4 inch projecting type. Finish: Dull chrome. 4. Catches: Magnetic type catches with aluminum case. Provide 30 lb. double catches for double doors and full height case doors; 12 lb. single catches used for single doors of base and wall-hung casework. Provide extruded aluminum dead bolt on left-hand door for locked double doors. 5. Drawer Slides: Steel 2-section drawer slides with nylon ball-bearing rollers for standard drawers and steel 3-section full extension drawer slides with ball bearings and nylon rollers for file drawers. All metal parts to be plated. Slide lengths and ratings shall suit particular application. 6. Provide plated #8 or #10 Pan head or Phillips head self-tapping high-low thread screws and washers for casework installation. 2.6 FABRICATION A. Field verify dimensions and installation conditions affecting the work. B. Shop fabricate casework in accordance with AWI Quality Standards. 1. Where details are not shown, comply with applicable Quality Standards or with alternate details acceptable to Architect/Engineer as fabricator's option. 2. Fabricate exposed edges of casework panels and shelving, including edges of casework doors and drawers, with matching materials. 3. Provide casework hardware, including hinges, pulls, adjustable shelving standards, brackets and clips, drawer slides, and accessories as indicated or required. Finish as selected by Architect/Engineer

6 C. Shop fabricate plastic laminate countertops and trim in accordance with AWI Quality Standards and drawing details. Bond plastic laminate to substrate in accordance with plastic laminate manufacturer's requirements. Keep joints to a minimum, no exposed metal accessories acceptable. 1. Provide exposed plastic laminate edges self-edged and built up to edge thickness detailed or accepted on final shop drawings. 2. Shop cut sink cutouts. Coordinate work with plumbing work. Obtain fixture templates as required to perform the work. 3. Protect exposed core surfaces that will be concealed after installation with two coats of sanding sealer. D. Fabricate finished work properly framed, closely fit and accurately set to required lines and levels and rigidly secured in place. E. Fabricate work straight, plumb, level and in true alignment; neatly and accurately fit, scribed and thoroughly secured. Miters and other joints shall be planed and sanded. All work shall be left clean and free from warp, twist, open joints and other defects. F. Provide finished woodwork dressed and sanded free from machine and tool marks, abrasions, raised grain or other defects on surfaces exposed to view in finished work. Exposed wood surfaces shall be uniform in color and grain. G. Assemble casework, countertops and similar items at the shop in largest possible sections and deliver to the site ready for installation. Shop fit work that cannot be shop assembled. H. Provide metal fabrications, brackets, supports as indicated on the drawings to support various millwork components. 2.7 FINISHING A. Quality Standard: Comply with AWI Section 1500 "Factory Finishing" for finishing preparation, including sanding, filling countersunk fasteners, and dealing with concealed surfaces and other preparations applicable to each unit of work. PART 3 - EXECUTION 3.1 PREPARATION A. Condition architectural woodwork materials and products for not less than 48 hours to average prevailing humidity conditions in installation areas before installing. B. Install blocking and anchoring devices built into substrates for anchorage of architectural woodwork items. C. Before installation, examine shop fabricated architectural woodwork for completion. Complete work as required, including back priming and removal of packing. 3.2 INSTALLATION A. Install architectural woodwork materials and products plumb, level, true and straight with no distortion. Shim as required using concealed shims. Install to a tolerance of 1/8" in 8'-0" for plumb and level (including countertops) and with 1/16" maximum offset in flush adjoining surfaces, 1/8" maximum offsets in revealed adjoining surfaces. B. Scribe and cut work to fit adjoining work and refinish cut surfaces or repair damaged finish at cuts

7 C. Anchor architectural woodwork items to built-in place blocking or directly attach to substrate framing. Secure to grounds, stripping and blocking with countersunk, concealed fasteners and blind nailing as required for a complete installation. Use finish nails for exposed nailing, countersunk and filled flush with woodwork and matching final finish where transparent finish is indicated. Plug and sand screw fastener holes. D. Install standing and running trim with minimum number of joints. Use full-length pieces, from maximum length of lumber available, to the greatest extent possible. Stagger joints in adjacent and related members. Cope at returns, miter at corners and comply with Quality Standards for joinery. Butt joints, except as detailed, are not acceptable. E. Install casework without distortion so that doors and drawers will fit openings properly and be accurately aligned. Adjust hardware to center doors and drawers in openings and to provide unencumbered operation. Complete the installation of hardware and accessory items as indicated. F. Install plastic laminate countertops and trim. Provide work level, true to alignment, accurately fit to wall conditions and securely fastened to base units and other support systems as indicated. 1. Seal intersection of countertops and applied splashes with bead of color matched silicone sealant. G. Install wood doors furnished under Section Provide pilot holes of proper size for screws in wood doors. Apply hardware in accordance with manufacturer's instructions. Adjust doors to provide uniform clearance and to contact stops uniformly. Remove and replace doors which are warped, bowed or otherwise damaged and cannot be properly fit. H. Install door hardware furnished under Section Apply door hardware in accordance with manufacturer's instructions. Fit door hardware before application of finish. Remove or protect during finishing operations. 3.3 CLEANING AND PROTECTION A. Repair damaged and defective architectural woodwork to eliminate functional and visual defects. Where not possible to repair properly, replace architectural woodwork items as directed by Architect/Engineer. B. Clean architectural woodwork items on exposed and semi-exposed surfaces. Touch-up shop applied finishes when required to restore damaged or soiled areas. 1. Clean hardware, lubricate and make final adjustments for proper operation. C. Provide temporary covers and protect installed work until final acceptance. END OF SECTION

SECTION ARCHITECTURAL WOOD CASEWORK

SECTION ARCHITECTURAL WOOD CASEWORK SECTION 06410 - ARCHITECTURAL WOOD CASEWORK PART 1 GENERAL 1.01 SECTION INCLUDES A. Wood cabinets for opaque finish. B. Flush wood paneling for transparent finish. C. Factory finishing. 1.02 RELATED REQUIREMENTS

More information

D. Product Certificates: Signed by manufacturers of casework certifying that products furnished comply with requirements.

D. Product Certificates: Signed by manufacturers of casework certifying that products furnished comply with requirements. SECTION 12356 - CASEWORK PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections,

More information

1. Division 6 Section "Rough Carpentry" for furring, blocking, and other carpentry work that is not exposed to view.

1. Division 6 Section Rough Carpentry for furring, blocking, and other carpentry work that is not exposed to view. SECTION 06402 INTERIOR ARCHITECTURAL WOODWORK PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division 1 Specification

More information

SECTION FINISH CARPENTRY PART 1 GENERAL. 1.1 SECTION INCLUDES A. Interior Finish Carpentry Work: 1. Refer to schedule at end of Section.

SECTION FINISH CARPENTRY PART 1 GENERAL. 1.1 SECTION INCLUDES A. Interior Finish Carpentry Work: 1. Refer to schedule at end of Section. SECTION 06200 - FINISH CARPENTRY PART 1 GENERAL 1.1 SECTION INCLUDES A. Interior Finish Carpentry Work: 1. Refer to schedule at end of Section. 1.2 RELATED SECTIONS A. Section 06100 - Rough Carpentry:

More information

SECTION CUSTOM CABINETS

SECTION CUSTOM CABINETS PART 1 GENERAL 1.01 SECTION INCLUDES A. Specially fabricated cabinet units. B. Countertops. C. Cabinet hardware. D. Preparation for installing utilities. 1.02 RELATED REQUIREMENTS SECTION 06410 - A. Section

More information

WHITE W/OAK TRIM NATURAL MEDIUM NORTHPORT OAK

WHITE W/OAK TRIM NATURAL MEDIUM NORTHPORT OAK WHITE W/OAK TRIM NATURAL MEDIUM NORTHPORT OAK Accessories. We believe that functionality is at the heart of any great kitchen. Above are a few of the accessories available with Merillat Essentials. The

More information

B. Shop Drawings: For residential casework. Include plans. elevations, details, and attachments to other work.

B. Shop Drawings: For residential casework. Include plans. elevations, details, and attachments to other work. HVAC 1Sunporch 1Fire Alarm Renovation SECTION 123530 RESIDENTIAL CASEWORK PART 1 - GENERAL 1.1 SUMMARY A. Section includes laundry room cabinets. 1.2 ACTION SUBMITTALS A. Product Data: For each type of

More information

SECTION MANUFACTURED CASEWORK

SECTION MANUFACTURED CASEWORK 1 GENERAL 1.1 SECTION INCLUDES SECTION 12300 MANUFACTURED CASEWORK A. Work required to complete the manufactured casework indicated by the Contract Documents, and the items necessary for its proper installation.

More information

SECTION ARCHITECTURAL WOODWORK

SECTION ARCHITECTURAL WOODWORK SECTION 06400 ARCHITECTURAL WOODWORK PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Custom Cabinet Units a. Plastic Laminate b. Sound Barrier for Casework 2. Cabinet Hardware B. Related Sections:

More information

ROWAN COUNTY AIRPORT APRIL 2017 TERMINAL EXPANSION

ROWAN COUNTY AIRPORT APRIL 2017 TERMINAL EXPANSION SECTION 12300 - MANUFACTURED CASEWORK PART 1 - GENERAL RELATED DOCUMENTS: Drawings, General Conditions and Supplementary General Conditions and other Division-1 Specification Sections, apply to this Section.

More information

SECTION FINISH CARPENTRY

SECTION FINISH CARPENTRY SECTION 06200 - PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections, apply to

More information

SECTION WOOD ARCHITECTURAL CABINETS AND LAMINATE COUNTERTOPS

SECTION WOOD ARCHITECTURAL CABINETS AND LAMINATE COUNTERTOPS SECTION 064113- WOOD ARCHITECTURAL CABINETS AND LAMINATE COUNTERTOPS PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions

More information

ADDENDUM TO THE CONTRACT. for the GLACIER FIRE STATION KITCHEN AND CLASSROOM RENOVATION. Contract No. E16-181

ADDENDUM TO THE CONTRACT. for the GLACIER FIRE STATION KITCHEN AND CLASSROOM RENOVATION. Contract No. E16-181 ADDENDUM TO THE CONTRACT for the ENGINEERING DEPARTMENT GLACIER FIRE STATION KITCHEN AND CLASSROOM RENOVATION Contract No. E6-8 ADDENDUM NO.: ONE CURRENT DEADLINE FOR BIDS: May 9, 206 PREVIOUS ADDENDA:

More information

SECTION PRE-MANUFACTURED CABINETS

SECTION PRE-MANUFACTURED CABINETS SECTION 12390 PRE-MANUFACTURED PART 1 GENERAL 1.1 DESCRIPTION OF WORK A. The work includes furnishing all labor, materials and equipment required to complete the Pre-Manufactured Cabinet work as shown

More information

Tender No Section St. James - Assiniboia Centennial Pool Fitness Facility Addition Page 1

Tender No Section St. James - Assiniboia Centennial Pool Fitness Facility Addition Page 1 Fitness Facility Addition Page 1 PART 1 GENERAL 1.1 SECTION INCLUDES.1 Finish carpentry items including shop prefabricated casework and countertops..2 Hardware and attachment accessories..3 Wood Benches..4

More information

SECTION WOOD ARCHITECTURAL CABINETS AND QUARTZ COUNTERTOPS

SECTION WOOD ARCHITECTURAL CABINETS AND QUARTZ COUNTERTOPS SECTION 064113- WOOD ARCHITECTURAL CABINETS AND QUARTZ COUNTERTOPS PART 1- GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions

More information

SECTION CUSTOM CASEWORK

SECTION CUSTOM CASEWORK PART 1 GENERAL 1.1 SECTION INCLUDES SECTION 06 41 00 CUSTOM CASEWORK A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division 1 specification sections,

More information

SECTION INTERIOR FINISH CARPENTRY. A. Lumber grading agencies, and the abbreviations used to reference them, include the following:

SECTION INTERIOR FINISH CARPENTRY. A. Lumber grading agencies, and the abbreviations used to reference them, include the following: SECTION 06 2023 PART 1 GENERAL 1.1 SUMMARY A. This Section includes the following: 1. Interior standing and running trim. 2. Interior stairs. 1.2 DEFINITIONS A. Lumber grading agencies, and the abbreviations

More information

DIVISION 6 WOODS AND PLASTICS SECTION FINISH CARPENTRY

DIVISION 6 WOODS AND PLASTICS SECTION FINISH CARPENTRY DIVISION 6 WOODS AND PLASTICS SECTION 06 20 23 PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01

More information

SECTION INTERIOR FINISH CARPENTRY

SECTION INTERIOR FINISH CARPENTRY SECTION 06 20 23 PART 1 - GENERAL 1.01 SUMMARY A. Section includes the following items for field-applied paint finish: 1. Interior standing and running trim. 2. Interior plywood paneling. B. Related Sections

More information

A. Product Data: For each type of product indicated cabinet hardware and accessories, and finishing materials and processes.

A. Product Data: For each type of product indicated cabinet hardware and accessories, and finishing materials and processes. SECTION 06402 - INTERIOR ARCHITECTURAL WOODWORK PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1

More information

Ash Brook Golf Course Scotch Plains, New Jersey

Ash Brook Golf Course Scotch Plains, New Jersey SECTION 062013 - EXTERIOR FINISH CARPENTRY PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification

More information

SECTION INTERIOR ARCHITECTURAL WOODWORK

SECTION INTERIOR ARCHITECTURAL WOODWORK SECTION 064023 INTERIOR ARCHITECTURAL WOODWORK PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Plastic-laminate cabinets. 2. Plastic-laminate countertops. 3. Plastic-laminate window sills. 4. Cabinet

More information

MASTERSPEC TECHNICAL SPECIFICATIONS DIVISION 08 - OPENINGS

MASTERSPEC TECHNICAL SPECIFICATIONS DIVISION 08 - OPENINGS SECTION 081433 - STILE AND RAIL WOOD DOORS PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Exterior stile and rail wood doors and sidelites. 2. Interior stile and rail wood doors. 3. Interior fire-rated,

More information

DIVISION 6 WOOD, PLASTICS AND COMPOSITES

DIVISION 6 WOOD, PLASTICS AND COMPOSITES DIVISION 6 WOOD, PLASTICS AND COMPOSITES PART 1 GENERAL 1.01 SECTION INCLUDES SECTION 06 1000 ROUGH CARPENTRY A. Rough opening framing for doors, windows, and roof openings. B. Roofing nailers. C. Preservative

More information

***************************************************************************************************************

*************************************************************************************************************** 06400 ARCHITECTURAL WOODWORK SPECIFIER: CSI MasterFormat 2004 number 06 40 00 PART 1 GENERAL 1.1 SUMMARY A. Provide necessary services, tools, equipment, material, and labor required to furnish and install

More information

B. Section Rough Carpentry: Support framing, grounds, and concealed blocking.

B. Section Rough Carpentry: Support framing, grounds, and concealed blocking. SECTION 06 41 00 - ARCHITECTURAL WOOD CASEWORK PART 1: GENERAL 1.1 SECTION INCLUDES A. Specially fabricated cabinet units. B. Cabinet hardware. C. Factory finishing. 1.2 RELATED REQUIREMENTS A. Division

More information

A. Dimension Lumber: Lumber of 2 inches nominal or greater but less than 5 inches nominal in least dimension.

A. Dimension Lumber: Lumber of 2 inches nominal or greater but less than 5 inches nominal in least dimension. SECTION 06 10 53 - MISCELLANEOUS ROUGH CARPENTRY PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01

More information

SECTION CUSTOM MILLWORK

SECTION CUSTOM MILLWORK PRT 1 GENERL 1.01 SECTION INCLUDES SECTION 06 41 00 Shop-fabricated plastic laminate-clad cabinet units. B. Countertops. C. Cabinet hardware. 1.02 SUBMITTLS See Section 01 30 00 -dministrative Requirements,

More information

B. American Society for Testing and Materials (ASTM):

B. American Society for Testing and Materials (ASTM): SECTION 06400 ARCHITECTURAL WOODWORK PART 1 GENERAL 1.01 SUMMARY A. Provide necessary services, tools, equipment, material, and labor required to furnish and install millwork and cabinet work. Install

More information

ADDENDUM NO. 1 THOROUGHBRED ROOM RENOVATION PHASE II DINING AREA MURRAY STATE UNIVERSITY, MURRAY, KY PROJECT #

ADDENDUM NO. 1 THOROUGHBRED ROOM RENOVATION PHASE II DINING AREA MURRAY STATE UNIVERSITY, MURRAY, KY PROJECT # ADDENDUM NO. 1 THOROUGHBRED ROOM RENOVATION PHASE II DINING AREA MURRAY STATE UNIVERSITY, MURRAY, KY PROJECT #13-046 10-23-2013 Bidders shall acknowledge receipt of this Addendum on the Bid Form, in the

More information

SECTION ARCHITECTURAL WOOD CASEWORK

SECTION ARCHITECTURAL WOOD CASEWORK PART 1 GENERAL 1.01 SECTION INCLUDES A. Specially fabricated cabinet units. B. Countertops. C. Cabinet hardware. D. Factory finishing. E. Preparation for installing utilities. 1.02 SUBMITTALS SECTION 06

More information

A. Boards or Strips: Lumber of less than 2 inches nominal size in least dimension.

A. Boards or Strips: Lumber of less than 2 inches nominal size in least dimension. HIGGINSVILLE HABILITATION CENTER MISC. BUILDING RENOVATIONS STATE OF MISSOURI HIGGINSVILLE, MISSOURI SECTION 061000 - ROUGH CARPENTRY PART 1 -GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions

More information

SECTION INTERIOR ARCHITECTURAL WOODWORK

SECTION INTERIOR ARCHITECTURAL WOODWORK SECTION 06 40 23 INTERIOR ARCHITECTURAL WOODWORK PART 1 GENERAL 1.01 SECTION INCLUDES A. Laminate clad cabinets and custom components. B. Laminate clad countertops. C. Cabinet hardware including countertop

More information

Addendum. McKee and Associates Architecture and Interior Design. No. ONE Date: Project:

Addendum. McKee and Associates Architecture and Interior Design. No. ONE Date: Project: McKee and Associates Architecture and Interior Design Addendum No. ONE Date: 10.8.18 Project: A New Office for Gaston Elementary School for The Etowah County Board of Education Gadsden, Alabama A1.1 GENERAL

More information

SECTION INTERIOR ARCHITECTURAL WOODWORK. A. Section includes interior woodwork items indicated not specified elsewhere and as specified.

SECTION INTERIOR ARCHITECTURAL WOODWORK. A. Section includes interior woodwork items indicated not specified elsewhere and as specified. SECTION 06 40 23 INTERIOR ARCHITECTURAL WOODWORK PART 1 - GENERAL 1.1 SUMMARY A. Section includes interior woodwork items indicated not specified elsewhere and as specified. B. Options: 1. Where casework

More information

MASTERSPEC TECHNICAL SPECIFICATIONS DIVISION 06 WOOD, PLASTICS AND COMPOSITES

MASTERSPEC TECHNICAL SPECIFICATIONS DIVISION 06 WOOD, PLASTICS AND COMPOSITES SECTION 064023 - INTERIOR ARCHITECTURAL WOODWORK PART 1 - GENERAL 1.1 SUMMARY A. This Section includes the following: 1. Interior standing and running trim. 2. Interior frames and jambs. 3. Stairwork and

More information

SECTION CARPENTRY

SECTION CARPENTRY SECTION 06100 CARPENTRY PART 1 GENERAL 1.01 SUMMARY A. Section Includes: Carpentry work including grounds, nailers, blocking, miscellaneous framing, plywood backing panels, plywood sheathing, preservative

More information

SECTION WOOD DOORS

SECTION WOOD DOORS SECTION 08211 WOOD DOORS Notice to Vendors: CANV prefers to purchase products that contain tropical wood only if they are certified according to the guidelines of the Forest Stewardship Council (FSC).

More information

Student Services & Classroom Addition

Student Services & Classroom Addition SECTION 105116 - WOOD LOCKERS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections,

More information

A. Provide all finish carpentry needed for a complete and proper installation.

A. Provide all finish carpentry needed for a complete and proper installation. SECTION 06200 - PART ONE GENERAL 1.1 SECTION INCLUDES A. Provide all finish carpentry needed for a complete and proper installation. B. Provide all wood, nails, bolts, screws, and all other items needed

More information

CaseworkUSA. specifications. 1.1 General 1.2 Summary. 1.3 Related Sections. 1.4 Definitions. 1.5 Qualifications and Quality Assurance

CaseworkUSA. specifications. 1.1 General 1.2 Summary. 1.3 Related Sections. 1.4 Definitions. 1.5 Qualifications and Quality Assurance 1.1 General 1.2 Summary A. This section includes the following Scope of Work as referred to in the plans: 1. Plastic laminate manufactured casework 2. Plastic laminate countertops 1.3 Related Sections

More information

SECTION INTERIOR FINISH CARPENTRY PART 1 - GENERAL 1.1 RELATED DOCUMENTS

SECTION INTERIOR FINISH CARPENTRY PART 1 - GENERAL 1.1 RELATED DOCUMENTS SECTION 062023 - INTERIOR FINISH CARPENTRY PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification

More information

SECTION PLASTIC-LAMINATE-FACED ARCHITECTURAL CABINETS AND COUNTERTOPS

SECTION PLASTIC-LAMINATE-FACED ARCHITECTURAL CABINETS AND COUNTERTOPS SECTION 06 41 16 - CABINETS AND COUNTERTOPS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification

More information

Music Area Casework General 1.01 Summary Related Sections Definitions Qualifications and Quality Assurance

Music Area Casework General 1.01 Summary Related Sections Definitions Qualifications and Quality Assurance 1.00 General 1.01 Summary Music Area Casework A. This section includes the following Scope of Work as referred to in the plans: 1. Thermally Fused Laminate manufactured casework, for use in music areas,

More information

Section Rough Carpentry

Section Rough Carpentry Section 06 10 00 Rough Carpentry 06 10 00-1 PART 1 - GENERAL 1.01 SECTION INCLUDES A. Blocking in wall and roof openings; wood furring and grounds; electrical panel back boards, concealed wood blocking.

More information

Alexandra Secondary College Refurbishment Project No: 1507 SECTION MANUFACTURED CASEWORK - SHOP BUILT 12300/1

Alexandra Secondary College Refurbishment Project No: 1507 SECTION MANUFACTURED CASEWORK - SHOP BUILT 12300/1 SECTION 12300 MANUFACTURED CASEWORK - SHOP BUILT 12300/1 PART I GENERAL 101 Scope The work of this Section covers the supply and installation of manufactured casework items. It includes but is not limited

More information

C. Installation shall be by experienced carpenters. Coordinate with plumbing and electrical contractors.

C. Installation shall be by experienced carpenters. Coordinate with plumbing and electrical contractors. 12300 - MANUFACTURED CASEWORK PART 1 - GENERAL 1.01 STIPULATIONS A. The specifications sections General Conditions, Special Requirements, and General Requirements form a part of this section by this reference

More information

SECTION MISCELLANEOUS ROUGH CARPENTRY

SECTION MISCELLANEOUS ROUGH CARPENTRY SECTION 06 1053 - MISCELLANEOUS ROUGH CARPENTRY PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01

More information

SECTION LAMINATE CLAD CASEWORK - COMMERCIAL

SECTION LAMINATE CLAD CASEWORK - COMMERCIAL SECTION 123400 LAMINATE CLAD CASEWORK - COMMERCIAL PART 1 GENERAL 1.01 SECTION INCLUDES A. Fixed modular laminate clad casework and components. B. Flexible rail mounted laminate clad casework and components.

More information

B. Related Requirements: 1. Section "Interior Painting" for priming and backpriming of interior finish carpentry.

B. Related Requirements: 1. Section Interior Painting for priming and backpriming of interior finish carpentry. 1 ~GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this Section. 1.2 SUMMARY

More information

WELLNESS CENTER REMODEL UNIVERSITY OF CALIFORNIA, MERCED MERCED, CALIFORNIA PROJECT NO.: 907432 C. Solid Surfacing Material: 1. Manufacturers: D. Wood: a. First Floor; Wilsonart International, Solid Surfaces,

More information

Bovard Studios Inc. Section April 6, 2004 Page 1

Bovard Studios Inc. Section April 6, 2004 Page 1 April 6, 2004 Page 1 This section includes solid flush and surface articulated wood doors, may have veneer facing, solid or glazed (stained glass) design, factory pre-fit, may be factory finished or site

More information

SECTION PLASTIC-LAMINATE-FACED ARCHITECTURAL CABINETS

SECTION PLASTIC-LAMINATE-FACED ARCHITECTURAL CABINETS SECTION 064116 - PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Plastic-laminate-faced architectural cabinets. 2. Wood furring, blocking, shims, and hanging strips for installing plastic-laminatefaced

More information

SECTION INTERIOR ARCHITECTURAL WOODWORK

SECTION INTERIOR ARCHITECTURAL WOODWORK SECTION 06402 - INTERIOR ARCHITECTURAL WOODWORK PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1

More information

Coordinate installation of rough carpentry members specified in other sections.

Coordinate installation of rough carpentry members specified in other sections. 1 1.03 Preservative treated wood materials. Concealed wood blocking, nailers, and C. Miscellaneous wood nailers, furring, and grounds. PART2 2.01 See Section 01 30 00 =Administrative Requirements, for

More information

A. All trim that has been damages, broken, or missing shall be repaired or replaced with material of the same size, shape, and type.

A. All trim that has been damages, broken, or missing shall be repaired or replaced with material of the same size, shape, and type. SECTION 062000 - FINISH CARPENTRY PART 1 - GENERAL 1.1 SECTION REQUIREMENTS A. All trim that has been damages, broken, or missing shall be repaired or replaced with material of the same size, shape, and

More information

DIVISON 6 WOODS AND PLASTICS SECTION PLASTIC LAMINATE FACED ARCHITECTUAL CABINETS

DIVISON 6 WOODS AND PLASTICS SECTION PLASTIC LAMINATE FACED ARCHITECTUAL CABINETS DIVISON 6 WOODS AND PLASTICS PART 1 - GENERAL 1:1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,

More information

SCI-FAB Product Specifications. Casework Section 1. Part 1 General

SCI-FAB Product Specifications. Casework Section 1. Part 1 General SCI-FAB Product Specifications Casework Section 1 Part 1 General 1.1 SCOPE OF WORK Includes all factory fabricated stainless steel casework as required by the project drawings. 1.2 TYPICAL INCLUSIONS A.

More information

Product Guide Specification

Product Guide Specification Shield Casework February 2014 3421 Merriam Lane Overland Park, Kansas 66203 Phone 913-744-2183 Fax 913-384-3477 Website www.shieldcasework.com E-mail info@shieldcasework.com Product Guide Specification

More information

RIVERSIDE MEDICAL CENTER 5/09

RIVERSIDE MEDICAL CENTER 5/09 SECTION 06200 - FINISH CARPENTRY PART 1 - GENERAL 1.01 DESCRIPTION: A. Work of this section is subject to requirements of the Contract Documents including the General Conditions and Supplementary Conditions

More information

SECTION INTERIOR ARCHITECTURAL WOODWORK

SECTION INTERIOR ARCHITECTURAL WOODWORK SECTION 064023 PART 1 - GENERAL 1.1 SUMMARY This Section includes the following: 1. Architectural wood casework: a. Plastic-laminate-faced cabinets. b. Wood-veneer-faced cabinets. 2. Countertops: a. Solid-surfacing

More information

Chevy Chase Club June 30, 2008 Bowie Gridley Architects

Chevy Chase Club June 30, 2008 Bowie Gridley Architects SECTION 081433 - STILE AND RAIL WOOD DOORS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification

More information

Lindenwold Boro Hall Lindenwold, NJ. Bishop & Smith Architects Laurel Springs, NJ. August 2, 2012 PART 1 - GENERAL 1.1 SUMMARY. A.

Lindenwold Boro Hall Lindenwold, NJ. Bishop & Smith Architects Laurel Springs, NJ. August 2, 2012 PART 1 - GENERAL 1.1 SUMMARY. A. SECTION 061000 - ROUGH CARPENTRY PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Wood blocking and nailers. 2. Wood furring and grounds. 3. Plywood backing panels. 1.2 ACTION SUBMITTALS A. Product

More information

SECTION ROUGH CARPENTRY

SECTION ROUGH CARPENTRY SECTION 06100 ROUGH CARPENTRY PART 1 GENERAL 1.1 DESCRIPTION OF WORK A. The work includes furnishing all labor, materials and equipment required to complete the Rough Carpentry work as shown on the Drawings

More information

NATURAL TOFFEE SABLE SEDONA KONA SENECA RIDGE MAPLE

NATURAL TOFFEE SABLE SEDONA KONA SENECA RIDGE MAPLE NATURAL TOFFEE SABLE SEDONA KONA SENECA RIDGE MAPLE Framed Door Styles Traditional Overlay Raised Panel Wood veneered raised panel doors feature concealed nickel-finished self-closing hinges. Drawer fronts

More information

SECTION FINISH CARPENTRY

SECTION FINISH CARPENTRY PART 1 - GENERAL 1.1 DESCRIPTION SECTION 06 20 00 1. Use this section only for NCA projects. 2. Delete between // // if not applicable to project. Also delete any other item or paragraph not applicable

More information

A. This Section includes interior architectural woodwork items indicated on Drawings and specified in this Section.

A. This Section includes interior architectural woodwork items indicated on Drawings and specified in this Section. SECTION 064023 - INTERIOR ARCHITECTURAL WOODWORK PART 1 - GENERAL 1.1 SUMMARY A. This Section includes interior architectural woodwork items indicated on Drawings and specified in this Section. 1.2 DEFINITIONS

More information

ADDENDUM TO BID DOCUMENTS ADDENDUM #03 SCCD RFP: # Project: Solano Community College District Vacaville Classroom Building (Annex) Renovation

ADDENDUM TO BID DOCUMENTS ADDENDUM #03 SCCD RFP: # Project: Solano Community College District Vacaville Classroom Building (Annex) Renovation Vacaville Classroom Annex Renovation Documents #18-005 ADDENDUM TO BID DOCUMENTS ADDENDUM #03 SCCD RFP: #18 005 Project: Vacaville Classroom Building (Annex) Renovation Date: 11/22/2017 Addendum # 03 The

More information

A. Work of this Section, as shown or specified, shall be in accordance with the requirements of the Contract Documents.

A. Work of this Section, as shown or specified, shall be in accordance with the requirements of the Contract Documents. Section 06400 Page 1 Section 06400 ARCHITECTURAL WOODWORK PART 1 GENERAL 1.1 GENERAL REQUIREMENTS A. Work of this Section, as shown or specified, shall be in accordance with the requirements of the Contract

More information

FT DIX ELEMENTARY SCHOOL PHASE VII, CLASSROOM ADDITION PEMBERTON TOWNSHIP REGAN YOUNG ENGLAND BUTERA, PC PROJECT #5349A

FT DIX ELEMENTARY SCHOOL PHASE VII, CLASSROOM ADDITION PEMBERTON TOWNSHIP REGAN YOUNG ENGLAND BUTERA, PC PROJECT #5349A SECTION 061050 - MISCELLANEOUS CARPENTRY PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification

More information

Copyright 2017 AIA MasterSpec Premium 05/17 PRODUCT MASTERSPEC LICENSED BY ARCOM TO WEREVER PRODUCTS, INC.

Copyright 2017 AIA MasterSpec Premium 05/17 PRODUCT MASTERSPEC LICENSED BY ARCOM TO WEREVER PRODUCTS, INC. This Product MasterSpec Section is licensed by ARCOM to Werever Products, Inc. ("Licensee"). This proprietary Product MasterSpec Section uses modified original MasterSpec text. Revisions made to the original

More information

Cascade Ph: Casework Fax: Corp

Cascade Ph: Casework Fax: Corp Cascade Ph: 541-928-3750 Casework Fax: 541-928-3880 Corp email: bill.yates@cascase.com Cascade Casework Corp SPECIFICATIONS FOR PLASTIC LAMINATE FACED CASEWORK Specifications Section 12300 Section 06400

More information

Product Guide Specification

Product Guide Specification RYNONE March 2, 2011 North Thomas Avenue, PO Box 128, Sayre, Pennsylvania 18840 P: (570) 888-5272 F: (570) 888-1175 W: www.rynone.com Product Guide Specification Specifier Note: This product guide specification

More information

SECTION PLASTIC LAMINATED CASEWORK

SECTION PLASTIC LAMINATED CASEWORK Specifications SECTION 123400 PLASTIC LAMINATED CASEWORK PART 1 GENERAL 1.01 SECTION INCLUDES This section provides the guidelines and standards for the manufacturing of plastic laminated casework and

More information

2. Wood grounds, nailers, blocking, miscellaneous framing, sleepers, etc.

2. Wood grounds, nailers, blocking, miscellaneous framing, sleepers, etc. 06100 - ROUGH CARPENTRY PART 1 - GENERAL 1.1 STIPULATIONS A. The specifications sections " General Conditions of the Construction Contract ", "Special Conditions", and "Division 1 - General Requirements"

More information

Multi-Institutional Academic Health Science & Research Center Evansville, IN

Multi-Institutional Academic Health Science & Research Center Evansville, IN SECTION 06 1053 - MISCELLANEOUS ROUGH CARPENTRY PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions Division 01 Specification

More information

SECTION BULLET- RESISTANT DOORS

SECTION BULLET- RESISTANT DOORS 1 SECTION 08 3950 BULLET- RESISTANT DOORS PART 1- GENERAL 1.01 SUMMARY A. This Section Includes: 1. Bullet- resistant steel door and frame systems. 2. Door hardware for bullet- resistant steel door and

More information

Architectural Woodwork Standards. casework. s e c t i o n

Architectural Woodwork Standards. casework. s e c t i o n Architectural Woodwork Standards casework s e c t i o n SECTION Introductory INFORMATION Guide Specifications...284 Introduction...285 Categories...285 Wood...285 Decorative Laminate...285 Solid Phenolic...285

More information

Installation Guide. Pionite Decorative Surfaces One Pionite Road, Auburn, Maine PIONITE ( )

Installation Guide. Pionite Decorative Surfaces One Pionite Road, Auburn, Maine PIONITE ( ) Installation Guide A Subsidiary of Panolam Surface Systems SMPBRO00-012 6/14 Pionite decorative laminates are designed for finished interior surfaces which require high impact, wear and stain resistance

More information

OCCE Courtroom Built-in SSA Jacksonville, NC

OCCE Courtroom Built-in SSA Jacksonville, NC OCCE Courtroom Built-in SSA 2015014.00 Jacksonville, NC ADDENDUM 2 ADDENDUM DATE: November 13, 2017 PROJECT: OWNER: ARCHITECT: BIDS DUE: Courthouse Courtroom Built-in 109 Old Bridge Street Jacksonville,

More information

AMPCO PRODUCTS, INC. TECHNICAL SPECIFICATIONS SOLID PHENOLIC CORE TOILET COMPARTMENTS

AMPCO PRODUCTS, INC. TECHNICAL SPECIFICATIONS SOLID PHENOLIC CORE TOILET COMPARTMENTS PART 1 - GENERAL 1.1 RELATED DOCUMENTS TECHNICAL SPECIFICATIONS SOLID PHENOLIC CORE TOILET COMPARTMENTS A. Drawings and General Provisions of Contract, including General and Supplementary Conditions and

More information

SECTION ROUGH CARPENTRY

SECTION ROUGH CARPENTRY SECTION 06 10 00 ROUGH CARPENTRY PART 1 - GENERAL 1.01 SUMMARY A. Section includes: 1. Framing with dimension lumber. 2. Wood blocking and nailers. 3. Plywood backing panels. 1.02 ACTION SUBMITTALS A.

More information

.1 Comply with the General Conditions of the Contract, Supplementary General Conditions and the requirements of Division 1.

.1 Comply with the General Conditions of the Contract, Supplementary General Conditions and the requirements of Division 1. PAGE 1 PART 1 GENERAL 1.1 REFERENCE.1 Comply with the General Conditions of the Contract, Supplementary General Conditions and the requirements of Division 1. 1.2 RELATED WORK SPECIFIED ELSEWHERE.1 Rough

More information

SECTION FINISH CARPENTRY. A. PART A and DIVISION 1 of PART B are hereby made a part of this SECTION.

SECTION FINISH CARPENTRY. A. PART A and DIVISION 1 of PART B are hereby made a part of this SECTION. SECTION 062000 PART 1 GENERAL 1.01 GENERAL REQUIREMENTS A. PART A and DIVISION 1 of PART B are hereby made a part of this SECTION. B. Examine all conditions as they exist at the project prior to submitting

More information

DIVISION 12 - FURNISHINGS. Section General Discussion. Introduction

DIVISION 12 - FURNISHINGS. Section General Discussion. Introduction Section 12000 - General Discussion This General Discussion Section contains material which is important to the successful fabrication and/or installation of furnishings and equipment in construction projects.

More information

DIVISION 11 EQUIPMENT SECTION PHOTO DARKROOM CASEWORK

DIVISION 11 EQUIPMENT SECTION PHOTO DARKROOM CASEWORK DIVISION 11 EQUIPMENT SECTION PHOTO DARKROOM CASEWORK PART 1 GENERAL 1.01 Scope of Work A. Provide material, accessories, tools, equipment and labor as required for the complete fabrication and installation

More information

WOOD WOOD

WOOD WOOD 12655 - WOOD 12655-1 Part One - General WOOD 1.0 All materials used in the finishing shall be of the highest grade of their respective kinds. Materials shall be evenly and smoothly applied by skilled mechanics.

More information

PART 1 GENERAL FINISH CARPENTRY

PART 1 GENERAL FINISH CARPENTRY SECTION 06 20 00 (06200) PART 1 GENERAL 1.1 SUMMARY A. Section Includes:. 1. Wood Millwork a. Interior Standing and Running Trim 2. Wood Stairs 3. Shelving 4. Composition Siding and Soffits and Trim a.

More information

Kenai Courthouse Expansion 2007 Section 06100

Kenai Courthouse Expansion 2007 Section 06100 Kenai Courthouse Expansion 2007 Section 06100 Rough Carpentry SECTION 06100 - ROUGH CARPENTRY PART 1 GENERAL 1.01 SECTION INCLUDES A. Structural wall framing. B. Preservative treated wood materials. C.

More information

The City of Winnipeg Section St. Vital Park Pavilion Page 1 of 1

The City of Winnipeg Section St. Vital Park Pavilion Page 1 of 1 The City of Winnipeg Section 06 10 13 WOOD BLOCKING AND CURBING St. Vital Park Pavilion Page 1 of 1 Part 1 General 1.1 SECTION INCLUDES.1 Roof curbs..2 Blocking in wall and roof openings..3 Wood furring

More information

B. Shop Drawings: For horizontal louver blinds, include fabrication and installation details.

B. Shop Drawings: For horizontal louver blinds, include fabrication and installation details. HIGGINSVILLE HABILITATION CENTER MISC. BUILDING RENOVATIONS STATE OF MISSOURI HIGGINSVILLE, MISSOURI SECTION 122113- HORIZONTAL LOUVER BLINDS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general

More information

SECTION INTERIOR ARCHITECTURAL WOODWORK

SECTION INTERIOR ARCHITECTURAL WOODWORK LSE ARCHITECTS, INC. LSE: 14.1001.01 SEWARD MONTESSORI SCHOOL ADDITION & REMODELING SECTION 06 40 23 PART 1 - GENERAL 1.01 SUMMARY A. Section Includes 1. Plastic-laminate clad cabinets and countertops.

More information

Lumicor CSI Specification Guide Open Format Section Solid Polymer Fabrication

Lumicor CSI Specification Guide Open Format Section Solid Polymer Fabrication Lumicor CSI Specification Guide Open Format Section 06650 Solid Polymer Fabrication I. GENERAL 1.01 DESCRIPTION A. Work described in this section: 1. Wall Partitions 2. Lighting 3. Table tops 4. Bar tops

More information

TOWN OF CULPEPER POLICE STATION

TOWN OF CULPEPER POLICE STATION SECTION 05520 - HANDRAIL AND RAILINGS PART 1 GENERAL 1.01 SECTION INCLUDES A. Guardrails. 1.02 REFERENCE STANDARDS A. ASTM A 53/A 53M - Standard Specification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated,

More information

DIVISION VI - WOOD AND PLASTIC

DIVISION VI - WOOD AND PLASTIC DIVISION VI - WOOD AND PLASTIC PART 1 - GENERAL 1.01 WORK INCLUDED SECTION 06112 - FRAMING AND SHEATHING A. Structural wall, and roof framing. B. Wall and roof sheathing. 1.02 REFERENCES A. ALSC - American

More information

DIVISION 6 WOOD AND PLASTICS

DIVISION 6 WOOD AND PLASTICS DIVISION 6 WOOD AND PLASTICS PART 1 - GENERAL 1.01 SUMMARY A. This Section includes the following: 1. Wood framing. 2. Wood supports. 3. Wood blocking. 4. Wood cants. 5. Wood nailers. 6. Wood furring.

More information

Product Guide Specification For Nonrated & 20-Minute Rated Doors

Product Guide Specification For Nonrated & 20-Minute Rated Doors Woodtech Trading Company 455 Fourth Avenue E.N. P.O. Box 2609 Columbia Falls, MT 59912 800-775-1352 (phone) 800-775-1353 (fax) www.woodtechdoor.com Product Guide Specification For Nonrated & 20-Minute

More information

Project Specifications Section SECTION ROUGH CARPENTRY Issued Final:

Project Specifications Section SECTION ROUGH CARPENTRY Issued Final: Project Specifications Section 061000 ROUGH CARPENTRY SECTION 061000 - ROUGH CARPENTRY Issued Final: 02-01-17 PART 1 - GENERAL 1.1 SUMMARY A. Scope: 1. Provide rough carpentry items where shown on the

More information

Product Guide Specification

Product Guide Specification Product Guide Specification Specifier Notes: This product guide specification is written according to the Construction Specifications Institute (CSI) 3-Part Format, including MasterFormat, SectionFormat,

More information