Cane Webbing Instructions from The Basket Maker's Catalog
|
|
- Leonard Bell
- 5 years ago
- Views:
Transcription
1 Cane Webbing Instructions from The Basket Maker's Catalog 521 East Walnut St. Scottsville, KY Back to Free Instructions If your chair has a groove around the seat opening, then choose Cane Webbing for replacing the seat. When using open cane webbing, determine the style (size) needed by measuring your old piece of cane from the center of one hole to the center of the next hole. Note: Fine Open 1/2" Mesh is the most popular size of Cane Webbing and is the size used in these instructions.
2 Cane Webbing comes in many different styles and sizes. It is sold by the running foot and is available in 18 inch and 24 inch widths. The Reed Spline size is determined by the width of your groove (size chart in Step 11 below) and is sold by the foot. See our On line Store for your Cane Webbing and Reed Spline choices. Open Cane Webbing Clo se Wo ven We bbi ng R a di o W e a v e R e e d S pl in e Pop Up Window What size is my open cane webbing
3 and how many feet do I need? You will need the following: Cane Webbing (Measure groove to groove + 4 inches) Reed Spline (circumference of groove + 1 foot) Caning Chisel to remove old Spline Glue Caning Wedges Scissors Shears Straight Chisel Razor Knife Spring type Clothespin Fine Sandpaper
4 Step 1. Soak cane webbing for 1 to 2 hours in hot water. Step 2. Wet the old spline. I used a wet paper towel. The water will soften the old spline and glue and make it easier to remove. Wipe any excess water from the chair.
5 Step 3. Clean out groove in chair with a caning chisel (or any small chisel). You may have to re wet the spline many times as you chisel. Note: I am now using another chair for these instructions. This chair has a groove with rounded corners, the chair in Step 3 has corners that meet at a right angle. See Note following Step 15 for square cornered chairs seats. Step 4. Once the groove is completely clean, gently sand the inside edge of your opening with fine sandpaper. You want the edge to be slightly rounded.
6 Also sand the inside edge of the groove. A sharp edge may cut the cane webbing so a slightly rounded edge is preferred. Step 5. Cut 4 pieces 3" long from your reed spline or you may use caning wedges.
7 Step 6. Check your wet cane webbing to see if it is flexible. If necessary, continue soaking the cane until it is flexible. Step 7. Stretch the webbing across the opening and center it over the opening (shiny side of cane webbing up). Using the back of a clothespin, gently push some of the webbing into the groove on the front of the seat and temporarily hold in place with a 3" piece of reed spline (or wedge). See tips below for pushing the cane webbing into the groove.
8 Push webbing into groove and secure with 3" piece of spline at the center front and back. Tip: As you push the cane webbing into the groove with the clothespin, lift the cane webbing that is outside the groove and push it down into the groove. Work small sections at a time and little by little the cane can be pushed down into the groove. Take care that you do not break the cane. If you do break a few strands, do not panic, the glue and spline will most likely hold the broken ends in place.
9 Step 8. Remove strands of cane along the corners if those strands lay past the groove. You may also use a caning wedge to help gently push the cane into the groove and to hold the cane in place.
10 Step 9. Push the cane webbing into the groove on each side of the seat and secure with a 3" piece of spline. Your webbing should now be stretched across the opening and held in place with the scrap pieces of spline. Check that the cane webbing is centered and that the strands run as straight as possible from the front to back and side to side. Step 10. Continue to gently push the webbing into the groove of your chair around the entire seat. The webbing should be all the way in the groove and sticking up on the outside edge of the groove. (Notice I had to trim and unweave the cane webbing at the corners so I could tuck it into the groove.)
11 Step 11. With a straight chisel or razor knife, cut the webbing just below the top of the groove on the outside edge. Remove the 3" long pieces of spline from your chair as you work your way around the seat. The razor knife came in handy for cutting the cane webbing in the corners.
12 The webbing should now be all the way in the groove, across the bottom of the groove, bending up the outside edge and cut just below the top of the groove. Step 11. Check your spline and if it's brittle, soak in hot water until pliable about 10 minutes. Note: The spline in the photo was dry yet pliable enough to make the bend needed. I did not soak this spline. Since the groove was 3/16" wide, I used #8 spline. Co de RS 70 F RS 75 F RS 80 F Descr iption # 7 Spline # 7.5 Spline # 8 Spline Wid th of Gro ove 5/3 2" 11/ 64" 3/1 6"
13 RS 90 F RS 95 F # 9 Spline # 9.5 Spline 7/3 2" 1/4" Step 12. Put Elmer's Glue All into the groove around the entire seat. We use a water soluble glue. If in the far distant future the chair needs a new seat, the spline should be easy to remove after soaking see Step 2. For canoe seats use a water proof glue. Follow the manufacturer's recommendations for drying times, etc. Step 13. Put the spline into the groove. The spline is tapered and the rounded (wider) side should face "up". Start in the middle at the back of your chair seat. (See Note following Step 15 for square cornered chair seats.) You may have to use a hammer to get your spline in place. Place a board on your spline and tap the board not the spline. Work the spline around the groove tapping as you go. The top of the spline should be flush or slightly higher than the cane webbing.
14 Step 14. With your shears, cut the spline so the ends meet and press into the groove. Step 15. Wipe away any excess glue with a damp cloth. Allow seat to dry thoroughly about 24 hours. The seat will tighten as it dries.
15 Note: If your chair has corners that meet at a right angle, use four pieces of spline and simply cut each piece at an angle at the corner. Congratulations you are finished. Your new chair seat should give you years of service and enjoyment.
CANE SEATS FOR CHAIRS. Revised Edition. Cornell Bulletin 681
CANE SEATS FOR CHAIRS Revised Edition Cornell Bulletin 681 CONTENTS 1 Select the Chair and Cane 2 Prepare To Weave The Seat The Cane Equipment You Need 3 How To Weave Square or Oblong Seats 12 Round Seats
More informationSAN FELIPE: Step by Step Pack 2
Pack 2 Your parts Stern reinforcement Bulkheads The poop deck Bulkhead planks Planks Tools and equipment Knife Pencil Wood glue Sandpaper File a Using leftover 5 x 5-mm wooden strips, measure and cut beams
More informationScissor Stool. Written By: Feitan
Scissor Stool If the stool is going to be kept indoors simply rub all the pieces with a Minwax WipeOn Poly before assembling the stool. If it is going to go outdoors use Minwax SparUrathane and coat all
More informationTrestle Table and Benches Materials List
Project 18444EZ: Trestle Table and Benches In the early days of our country, trestle tables were popular because they could easily be disassembled and moved out of the way when not in use no small advantage
More informationClay Modeling Film. Features of Clay Modeling Film. Use Clay Modeling Film
Clay Modeling Film The series of Clay Modeling Film, originally developed by TOOLS INTERNATIONAL Corp, is mainly used for interior/exterior shape confirmation, checking highlights and qualification studies
More informationRepairs. Chapter 10 Repairs 10. 1
10 Repairs Chapter 10 Repairs 10. 1 Repairs As an installer, you will probably be called upon to repair damage to a resilient floor. Here are some of the most common problems and the recommended repairs
More informationHarriet Chair with Modifications
Harriet Chair with Modifications This modification of the Harriet chair includes a slat back, padded seat, and is 2 inches wider than the original plan. The overall dimensions of the finished chair: 38
More informationEXTREME LOAD no. TWO
1602 - EXTREME LOAD no. TWO Kit Features: 22' 4 " x 14' x 3'-6 Oversize Load 49mm (1.9") actual height Bolt Head Details Welded Load Mounting Fins Painting Handles Tools Required: Hobby Knife Tweezers
More informationGrade 11 Woods Lift Lid Coffee Table. Based on Under the big Top from Popular Mechanics Website
Grade 11 Woods Lift Lid Coffee Table Based on Under the big Top from Popular Mechanics Website TABLE TOP 1. Select enough lumber to construct a top that is between 22 ½ and 24 wide after jointing. Ensure
More informationKentucky 4H Wood Science Plans Notebook. Plans Level 1
Kentucky 4H Wood Science Plans Notebook Plans Level 1 MATERIALS NEEDED: 1 piece wood 3/4" x 2 x 2 1 piece wood 3/4" x 3 x 3 1/2" 1 wooden spring-type clothespin 2-1 1/2" nails 1-1/2 woodscrew Wood Glue
More informationObtained from. Omarshauntedtrail.com
BORN2HAUNT.COM http://www.born2haunt.com/batsreasy01.html Bats R Easy Here is another way to make bats with foam and wire. The first thing I did was cut a piece of scrap foam to the size I wanted 5" long,
More informationSPLINT SEATS FOR CHAIRS. Cornell Bulletin 682
SPLINT SEATS FOR CHAIRS Cornell Bulletin 682 Ruth B. Comstock CONTENTS 1 Select the chair Select the splint 2 Equipment you need 3 Prepare to weave The seat The splint 4 How to weave Warping Weaving Other
More informationTHE PODIUM MUSIC STAND
THE PODIUM MUSIC STAND 1 Set Assembly Instructions Wooden Parts: a. 1 Column b. 2 Long Slide Pieces c. 2 Slide Spacers (1 long & 1 short) d. 4 Feet e. 2 Fork Pieces f. 1 Fork Spacer g. 2 Long Desk Frame
More informationHow to Mitre Mouldings
How to Mitre Mouldings About Window and Door Mouldings Mitre cuts are a basic operation in most moulding installation. Mitre cuts are typically 45 degree angles, however many installations require minor
More informationWindsor Chair Online. Assembly Instructions
Windsor Chair Online Assembly Instructions Date: 1/4/2007 Other Chairs Offered Philadelphia Arm Chair New England Comb Back Sackback d Arm Chair Bow Back Side Chair Fan Back Side Chair Page 1 Table of
More informationThere are three primary units to this box: two three-sided trays (one made to fit over the other) and one case that wraps around the trays.
Instructions for Basic Drop-Spine Box by Sandra Liddell Reese There are three primary units to this box: two three-sided trays (one made to fit over the other) and one case that wraps around the trays.
More informationFor Barrel Tapers. Installation and Operating Instructions for use with table saws and large disk sanders
Tim s Taper Tool For Barrel Tapers Installation and Operating Instructions for use with table saws and large disk sanders Your taper tool is capable of making barrel tapered shafts. The term barrel is
More informationCANING AND SEAT REPAIR
SEAT WEAVING - FOUR RAIL HOW-TO PHAMPLETS ART FIBER FLAT SEATING Simulates the look of hickory splint when woven. One pound will do and average size (12 x ) chair seat. Sold by the pound. 520019 520003
More informationLittle Briana Cottage Dollhouse assembly instructions
Little Briana Cottage Dollhouse assembly instructions NOTE 1: Please do a dry assembly using only tape to hold house together. This will get you familiar with parts, location, and fit. This also gives
More informationHow to install backchecks
How to install backchecks Note: All pictures can be enlarged for better clarification. Revision 7 8/2009 Backchecks wear out in a piano much like brake pads in an automobile. While wear is a valid reason
More informationOnce you ve finished building the frame of
Weaving a Splint Seat for the Delaware Chair May/June 2018 Once you ve finished building the frame of the Delaware Chair from our May/June 2018 issue, you ll need to fashion a seat for it. Read on for
More informationRugged Ridge Body Armor Guard Kit, 5 Pieces, Black (07-Current JK 4-door)
Rugged Ridge Body Armor Guard Kit, 5 Pieces, Black (07-Current JK 4-door) Installation Time: 60 Minutes Tools Required: Notes: Phillips head screwdriver 3/8 socket or Flat head screwdriver 1/2 socket 7
More informationSan Felipe: Step by Step Pack 3
Pack 3 Your parts Bulwarks Gun port covers x 2 Tools and equipment Wood glue Sandpaper Brushes Wood stain Hammer Pin pusher/nails Razor saw a Remove the longer bulwark and test-fit it in place at the bow
More informationCounter Height Bar Stool [1]
Counter Height Bar Stool [1] Submitted by AndyH [2] on Wed, 2015-03-11 09:58 These stools are ideal for a kitchen counter and I made them to fit ours [1] Page 1 of 10 which is about 36 inches from the
More informationBasic Instructions. Preparing the Moulds
Preparing the Moulds Basic Instructions 1. Make sure the moulds are clean and free of plaster residue (see our CARE & CLEANING instructions for more information). 2. Rinse the moulds in warm water and
More informationMaterials and Tools: Printer s Triple Console Cabinet. Free Plans to build a Triple Console Cabinet
Materials and Tools: Materials: 3 sets euro style bottom corner mount drawer slides, 16 length 3 sets inset hinges 24 cup style handles 8 2x2 @ 8 feet long 6 1x3 @ 8 feet long 6 1x2 @ 8 feet long 1 sheet
More informationPRO CYC PRO CYC, INC. SYSTEM SUPER 3EZ
ASSEMBLY INSTRUCTIONS SYSTEM SUPER 3 EZ Congratulations on your decision to use the world s most advanced and user-friendly cyclorama system. We have taken a great deal of care to create and ship your
More information2. Sanding the Modules Sand the entire surface of each cyc module with 60-grit sandpaper. This will provide for better paint adhesion.
ASSEMBLY INSTRUCTIONS SYSTEM 4 BI (Built-In) Congratulations on your decision to use the world s most advanced and user-friendly cyclorama system. We have taken a great deal of care to create and ship
More informationCoat Rack. Materials: Directions:
Coat Rack 2x2 wooden poplar (foundation of the rack) 3/4 inch diameter wood dowels (5-8 depending on how many arms you want) 1/4 inch dowel screw 1/4 inch drill bit Power drill Ruler Pencil Paint/spray
More informationEngineering Directive
Thing-a-ma-Jig Finishing To Finish a model means to apply paint and other decorations to complete the look of your model. Meaning to apply a finish. That is what we will discuss in this section. Applying
More informationSCULL HANDLES AND GRIPS INSTRUCTION BOOKLET
SCULL HANDLES AND GRIPS INSTRUCTION BOOKLET Contents Section I: Scull Grip Replacement: Fixed Handle or 10 cm Length Adjustment System Refer to this section if you need to replace the grips on your fixed
More information'Mutiny' Ozone Reactor Kit
'Mutiny' Ozone Reactor Kit Skill Level: Beginner Tools Required: Scissors or razor blade Other Materials: Teflon tape Time to Build: Approximately 1 hour not including drying time Version: 2012 spray nozzle
More informationShelf Divider Top Panel. Trim Piece
Page 1 Shelf Divider Top Panel SCAN FOR ASSEMBLY VIDEO Side Panel Long Shelf Panel Side Panel Bottom Panel Trim Piece Package Contents *Please verify that you have the correct number of parts before proceeding.
More informationMUDGUN Drywall Finishing System
Watch the demonstration video online at hydetools.com MUDGUN Drywall Finishing System Quick Start Guide Hyde Tools, Inc. / A Hyde Group Company / 800-872-4933 / custrelations@hydetools.com / hydetools.com
More informationFLEXITEEK INSTALLATION INSTRUCTIONS
an Advanced Plastic Fabrications Company 99 marcus Blvd., 631.244.3620 631.231.4466fax FLEXITEEK INSTALLATION INSTRUCTIONS Before you begin, take your new Flexiteek deck out of the shipping package and
More information1983 Jaguar XJS Interior Wood Trim Repair and Refinishing
The following describes and shows one method of wood trim repair/restoration/refinishing for wood trim on Jaguar cars, specifically this 1983 Jaguar XJS, although the wood trim should be the same in all
More informationBuilding the Gothic Church
Building the Gothic Church Mold #54 does not contain all of the blocks to build this church. You will need extra regular blocks (1/2" x 1/2" x 1") and square blocks (1/2" x 1/2" x 1/2"). These blocks can
More informationFRAMED PANEL / DOOR / PANEL CONTINUOUS HINGE SHOWER ENCLOSURE INSTALLATION INSTRUCTIONS
FRAMED / DOOR / CONTINUOUS HINGE SHOWER ENCLOSURE INSTALLATION INSTRUCTIONS QCI5229 Rev 0 6 INSTALLATION NOTES: Unpack your unit carefully and inspect for freight damage. Lay out and identify all parts
More informationFlamingo. That s what I looked
Plans N O W w w w. P l a n s N O W. c o m flip-seat Storage Bench Flamingo. That s what I looked like as I stood in the doorway perched on one leg, with my other foot raised so that I could untie the laces
More informationSLIM TRIM MOULDING INSTALLATION METHODS
Slim Trim as a reducer Use SlimTrack (Metal Track) for up to 4 mm floors. Up to 4 mm Floors 3/8 *If the flooring manufacturer suggests/permits the use of underlayments you may need to shim the track to
More informationHow to Rehandle and Repair that Old Hammer - a Step by Step Tutorial by Bob Sturgeon
How to Rehandle and Repair that Old Hammer - a Step by Step Tutorial by Bob Sturgeon There is a world of old collectible and user hammers out there floating around just waiting to be resurrected. Hammers
More informationL.L.Bean. Farmhouse Futon
L.L.Bean Farmhouse Futon Thank you for purchasing our Farmhouse Futon. Assembly of this product requires a Phillips Head Screwdriver and Flat Head Screwdriver. We have found it helpful to have a second
More information2. Sanding the Modules Sand the entire surface of each cyc module with 60-grit sandpaper. This will provide for better paint adhesion.
ASSEMBLY INSTRUCTIONS SYSTEM SUPER 2.5 EZ Congratulations on your decision to use the world s most advanced and user-friendly cyclorama system. We have taken a great deal of care to create and ship your
More informationExterra Installation Guide
Exterra Installation Guide Installing the foam padding Please review this installation guide before you begin installing the floor. If you have any questions, please call us at 800-428-5306 any time Monday
More informationFollow the numbered instructions that correspond to an illustration below:
Folded Christmas Star Materials needed: Colored or white paper X-acto knife and cutting mat or scissors Ruler Patience and practice :) Instructions Follow the numbered instructions that correspond to an
More information"Tidy Up" End Table [1]
[1] Submitted by Ana White [2] on Tue, 2012-07-03 18:13 [1] Additional Photos Page 1 of 14 [3] [4] [5] [6] [7] Hi everyone! Well, we are making our way home from a week long camping trip through Alaska
More informationVivian Mansion Assembly Instruction By Laser Dollhouse Designs
Vivian Mansion Assembly Instruction By Laser Dollhouse Designs NOTE 1: Please do a dry assembly using only tape to hold house together. This will get you familiar with parts, location, and fit. This also
More informationInstallation Instructions for DIY or Completed 45 Degree Light Channel
201 Edge Lighting. All Rights Reserved. Installation Instructions for DIY or Completed Degree Light Channel IMPORTANT INFORMATION - This instruction shows a typical installation. 11 W. Fullerton Ave Chicago,
More information5If the protruding part is. 6Place 1 as is shown in the. 7Place what was assembled
Yamato: Step-by-step 49 The base of the bridge and strakes a c b d a Base of the bridge b Base of the bridge c Base of the bridge d Strakes x 10 THE BASE OF THE BRIDGE 1Smooth 1 to 3, first using the metal
More informationMaking Paper. A Wood Magic Show Project for Kids
Making Paper A Wood Magic Show Project for Kids 2001 Contents: Introduction 1 Before you begin 2 What you will need 3 Instructions Making your frames Making your slurry Making your paper mat Drying your
More informationFright Research Spooky Sign
Fright Research Spooky Sign Instruction Manual September 2018, Rev - - 1 - http://www.frightresearch.com Spooky Sign Parts List INCLUDED 1 Main Sign 24.5 x 18 1 Bottom Sign 16 x 4 1 Chain link 8 Eye hooks
More informationPEAK OAK OAK FLOORING, OAK DOORS & WROUGHT IRONWARE
PEAK OAK OAK FLOORING, OAK DOORS & WROUGHT IRONWARE How To Assemble An Oak Ledged Door www.peakoak.co.uk Introduction Some of you choose to order your oak ledged doors in kit form and the following guide
More informationCobra X Q Construction Tips Construction: Bel y pan
Cobra X Q Construction Tips : The white plastic in this kit is high impact styrene. It can be painted with most types of coatings if light coats are applied this is necessary due to the thickness of the
More informationBen Franklin 5&10 Store
Ben Franklin 5&10 Store RIVER LEAF MODELS, LLC RIVER LEAF MODELS, LLC Thank you for purchasing the Ben Franklin 5&10 structure kit. Your kit includes everything you need to assemble the final product.
More informationIf you intend to hang lining paper and haven't yet then see our guide to hanging lining paper.
Welcome to our guide to hanging wallpaper, we have split this tutorial into two parts, in this part we will cover roll calculation, wall preparation, order of hanging, marking out and cutting the lengths.
More informationNoville School Diorama Part 4 Making the Floors and Plastering the Walls and Ceilings
Noville School Diorama Part 4 Making the Floors and Plastering the Walls and Ceilings Moulds and Materials Making the Floors Plastering the Ceiling Plastering the Walls Installing the Ceiling and Floor
More informationAntique Trunks: Refinish, Repair, Restore, Revised and Expanded
15. Patch any holes on the inside of the trunk: There will often be splits or holes on the inside of the trunk that may or may not be visible from the outside. Most often they are holes left by the removal
More informationPROJECT PLANS WOODEN GIFT BOX
PROJECT PLANS WOODEN GIFT BOX Make the gifts you give even more special by presenting them in this one-of-a-kind gift box. In fact, the box may be valued more than whatever it contains. The box is sized
More informationBasic Stenciling Techniques
Metal Stencil Techniques For each technique you ll need the equipment listed in addition to your stencil and removable tape. To avoid bending your stainless steel stencils, keep them flat at all times.
More informationHudson Dresser [1] Hudson Dresser Published on Ana White ( Submitted by dan-k [2] on Fri, :43 [1]
[1] Submitted by dan-k [2] on Fri, 2011-03-11 11:43 [1] If you plan on staining this piece, it is recommended that you stain all of the drawer face materials before assembly for a more professional look.
More informationHow to Install EZ Snap Window & Skylight Shades
How to Install EZ Snap Window & Skylight Shades Congratulations on your purchase of EZ Snap Shades You ve taken the first step in reducing your energy consumption, while blocking harmful UV rays, unwanted
More informationPITTS S2S CONSTRUCTION
PITTS S2S CONSTRUCTION FUSELAGE CONSTRUCTION 1) Place the right fuselage side over the plan and mark the former positions. Place the left side over the right side and mark the former positions. Glue F1
More informationHOGNOSE PSALTERY KIT Assembly Instructions
HOGNOSE PSALTERY KIT Assembly Instructions WOOD PARTS 1 Plywood Top (Soundhold Pre-Cut) 1 Plywood Bottom 2 Pin Blocks 1 Short Side 1 Long Side 1 Bridge 1 Scrap of Plywood HARDWARE 1 L-Handle Tuning Wrench
More informationLearn to weave on the. Inklette Loom
Learn to weave on the Inklette Loom THE ASHFORD INKLETTE LOOM top rear peg Inkle bands are strong and useful braids. Create colourful belts, bracelets, ties, guitar straps, shoe laces or trims for weaving.
More informationAbout.com :
http://woodworking.about.com/gi/dynamic/offsite.htm?sit...//www.popularwoodworking.com/features/fea.asp%3fid=1088 (1 of 8)1/28/2004 12:05:01 AM Modern Storage Tower The last thing I want to do when starting
More informationPatrick's Beach Cottage Dresser [1]
[1] Submitted by Ana White [2] on Fri, 2011-05-27 12:23 [1] Additional Photos Page 1 of 17 [3] Special thanks to Patrick for sharing his dresser with us. After so many of you requested plans, I'm so very
More informationPRO CYC PRO CYC, INC. SYSTEM SUPER 1.5 EZ
ASSEMBLY INSTRUCTIONS SYSTEM SUPER 1.5 EZ Congratulations on your decision to use the world s most advanced and user-friendly cyclorama system. We have taken a great deal of care to create and ship your
More informationBUILD YOUR OWN DOG SLED
Page 1 of 15 BUILD YOUR OWN DOG SLED Note: I have lost track of Charlie Yeager. His old email address is yeagerc@server.greatlakes.k12.mi.us, but it no longer functions. National Mine School, Ishpeming,
More informationMax Launch Abort System Prod. No *Kevlar is a registered trademark of Dupont
Flying Model Parts List Max Launch Abort System Prod. No. 3014 A 11820 - Body Tube 3.5 Diam x 5.5" Long B 11824 - Orange Capsule Base Shoulder Ring C 16032 - Laser-cut Ring motor mount rear D 16033 - Laser-cut
More informationNotes for Making Wood Rings With Stainless Steel Insert Centers
Notes for Making Wood Rings With Stainless Steel Insert Centers Background These notes describe how to make a ring with a stainless steel (SS) insert and a wood exterior band. They also include information
More informationINSTALLATION INSTRUCTIONS FRAMELESS CONTINUOUS HINGE SHOWER ENCLOSURE QCI5232
INSTALLATION INSTRUCTIONS FRAMELESS CONTINUOUS HINGE SHOWER ENCLOSURE QCI5232 QCI5232 Rev 0 Page 1 Certified 06/20/2016 INSTALLATION NOTES: Unpack your unit carefully and inspect for freight damage. Lay
More informationBridgeport Braxton Sauna Installation & Owner s Manual
Bridgeport Braxton Sauna Installation & Owner s Manual Read this entire manual through to the end before proceeding with the assembly. Bridgeport Braxton Installation & Owner s Manual Note: While there
More informationHow To Create An Entertainment Unit
How To Create An Entertainment Unit Materials required: 2 x Pine Panels - 1800mm x 450mm x 18mm 4 x Pine Panels - 310mm x 450mm x 18mm 1 x Pine Panels - 650mm x 450mm x 18mm 6 x Bun feet (your choice of
More informationA Day House. A View of One Way to Finish the Exterior of The Day House. Read these instructions all the way through before beginning this project.
A Day House A View of One Way to Finish the Exterior of The Day House Read these instructions all the way through before beginning this project. General Comments For the purposes of this project, the standard
More informationMaking Homemade Paper
Making Homemade Paper Summary The art and business of paper-making dates back about 2000 years ago! At that time, a Chinese government official named Ts ai Lun was the first to develop a paper-making method
More informationPRO CYCTM PRO CYC, INC. SYSTEM 1.5 FS
ASSEMBLY INSTRUCTIONS Congratulations on your decision to use the world s most advanced and user-friendly cyclorama system. We have taken a great deal of care to create and ship your cyc, so please take
More informationThe Hearse Carriage Assembly Instructions Page 1.
The Hearse Carriage Assembly Instructions Page 1. The Hearse Carriage Assembly Instructions Page 2. WHAT YOU'LL NEED: Scissors, Elmer's glue (or a glue stick), a needle, two toothpicks, a sharpened pencil,
More informationI I. . i1 AD JUSTABLE SHELVES
ADJUSTABLE SHELVES HAD BEEN TRYNG TO WORK out a really simple (read "fast") way to make an elegant wooden version of the old standby, metal standards and brackets. Although have seen many commercial versions
More information4 Column Display Row Corner
4 Column Display Row Corner Page 1 IMPORTANT! If you purchased a 2 Column Display Row Corner Kit, your package will contain the following parts: END LADDER ASSEMBLIES - x4 1 COLUMN SCREWLESS CONNECTORS
More informationAlmost Heaven Saunas THE AUTHENTIC SAUNA EXPERIENCE. Rainelle Sauna Installation & Owner s Manual
Almost Heaven Saunas THE AUTHENTIC SAUNA EXPERIENCE Rainelle Sauna Installation & Owner s Manual Almost Heaven Saunas THE AUTHENTIC SAUNA EXPERIENCE Read this entire manual through to the end before proceeding
More informationPre-Paint>Fuselage>Empennage>Fit elevator. Objectives of this task: Materials required: Prepare the horizontal stabiliser and the elevator
Pre-Paint>Fuselage>Empennage>Fit elevator Objectives of this task: To fit the elevator to the horizontal stabiliser, to fit the trim tabs to the elevator and the end caps to the elevator and the horizontal
More informationDrop Spine Box. Tricia Morris. Design by: 2006 Craft TV Weekly, Inc.
Drop Spine Box Design by: Tricia Morris 1 Think inside the box! In a marathon of gluing, folding and smoothing, Tricia shows how to make a Drop Spine Box. The steps are many, but the reward is great! So
More informationInstallation Guidelines
Page 1 Two inch () Porch Screening System Extruded Screen Walls Only Kit Installation Guidelines Tools You ll Need 4 ft. Carpenter s level Chalk line (to mark U channel locations) Chop saw with a metal
More informationLAMINATE FLOORING INSTALLATION INSTRUCTIONS READ ALL INSTRUCTIONS BEFORE BEGINNING INSTALLATION.
READ ALL INSTRUCTIONS BEFORE BEGINNING INSTALLATION. If your starting wall is uneven, refer to Fig 11 to prevent having to uninstall rows. Taking measurements to ensure you will not have too small a final
More informationBUILDING A GOAL WALL DO IT YOURSELF! INSTRUCTIONS FOR A GOAL WALL
INSTRUCTIONS FOR A In just a few steps, we show you how to build your own goal wall and paint it perfectly. COMPILED BY 1 PREPARING Purchase the materials from the enclosed list. The DIY store should be
More informationEasy, Economical Garage Shelving from 2x4s [1]
[1] Submitted by Ana White [2] on Thu, 2014-09-11 12:01 [1] Additional Photos [3] Page 1 of 10 [4] [5] Thanks so much for watching my newest video on building a 20' long garage storage shelving unit! I
More informationAssembly instructions for the Simple Marble Machine
Assembly instructions for the Simple Marble Machine Page number 1 Parts layout Page number 2 Please note: All the assembly can be done with PVA glue. Don't apply it from the bottle or tube but put a blob
More informationFeatures in Fabric STEP: 2 STEP: 1
Features in Fabric We have all been saving scraps of fabric left over from other projects, right? With the Features in Fabric Board, you can mount fabric and embroidery for display simply and attractively.
More informationBrook sectional corner. assembly instructions
Brook sectional corner assembly instructions Smooth & Wrinkle-Free Fabric Covers: In addition to these printed instructions, you may want to watch our beauty tips videos on the customer service page of
More informationModel 209 Fireback Replacement
Model 209 Fireback Replacement Please read all the instructions before you begin the procedure. Confirm that you have all the necessary tools and materials. If you have any questions, technical support
More informationWILDING WALLBEDS INSTALLATION INSTRUCTION Side Mount
WILDING WALLBEDS INSTALLATION INSTRUCTION Side Mount For Wallbed models: Do-It-Yourself Insturction booklet C92 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE
More informationPrinting and Assembly of Kwawu Arm
Printing and Assembly of Kwawu Arm Jacquin Buchanan December 2016 This work is licensed under the Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License. To view a copy of this
More informationPirate's Treasure Trunk [1]
[1] Submitted by JoanneS [2] on Sat, 2013-09-14 15:34 [1] Additional Photos [3] Page 1 of 16 [4] [5] [6] For this build, I wanted to try out the concept of using something unconventional as the hinge for
More informationBowed Psaltery Kit. Musicmaker s Kits P.O. Box 2117 Stillwater MN (651)
Bowed Psaltery Kit Musicmaker s Kits P.O. Box 2117 Stillwater MN 55082 (651) 439-9120 www.harpkit.com Parts list: BOWED PSALTERY KIT 2 long side rails 2 short side rails 1 pin block 1 front (soundboard)
More informationMustang Eleanor Style Louvers - Pre-painted (05-10) - Installation Instructions
Mustang Eleanor Style Louvers - Pre-painted (05-10) - Installation Instructions The below installation instructions work for the following products: Mustang Eleanor Style Louvers - Pre-painted (05-10)
More informationPeaches & Blueberries. by Donna Hodson
Peaches & Blueberries by Donna Hodson Peaches & Blueberries By Donna Hodson Palette: DecoArt Americana Acrylics Antique Gold #13009 Antique Maroon #13160 Burnt Umber #13064 Cadmium Red #13015 Colonial
More informationAmerica s leading woodworking authority To download these plans, you will need Adobe Reader installed on your computer. If you want to get a free copy, visit: http://adobe.com/ reader. Having trouble downloading
More informationMimi's Hall Tree Hutch [1]
[] Submitted by Ana White [2] on Mon, 202-02-06 3:38 [] I am so glad you all liked Mimi's Hall Tree. [3] On Friday, I put together plans for the bench shown at the base of this hall tree. Page of 20 Bench
More informationRaised Planter Box [1]
[1] Submitted by tracysmith [2] on Sun, 2012-04-15 04:38 [1] The inspiration piece is built out of cedar, if you use a different species of wood and plan to use this outside as intended, make sure you
More informationStep by Step Wing Bagging
Step by Step Wing Bagging By Evan Shaw 073 589 9339 evanevshaw@gmail.com Preparing the Leading Edge 1. Cut cores. (Cutting of wing cores is covered in another article elsewhere) 2. Sand the LE to a nice
More information