How To Create An Entertainment Unit

Size: px
Start display at page:

Download "How To Create An Entertainment Unit"

Transcription

1 How To Create An Entertainment Unit Materials required: 2 x Pine Panels mm x 450mm x 18mm 4 x Pine Panels - 310mm x 450mm x 18mm 1 x Pine Panels - 650mm x 450mm x 18mm 6 x Bun feet (your choice of style) 1 x Plywood mm x 1200mm x 10mm (or thinner) 1 x 500ml Selleys Aquadhere Interior 1 packet 25mm wall panel nails 6 x 8x45mm screws Minimum Tools required: Router and router bit 18mm or smaller Carpenters Square Hammer Saw Straight edge longer than 450mm 2 x (F) or (G) clamps Measuring tape Pencil Sharp chisel or utility knife 1. Take one of the full length panels (1800mm) and mark the centre of the length of the panel (900mm). Then measure and mark 320mm either side of the centre mark. From these marks, measure and mark a further 500mm on either side. 2. Place one of the 310 x 450 pieces on top of the marked line, then take a pencil and draw a line on either side using a square to keep it true. This marks out the channel to be routed.

2 3. Set Router cutter depth to 6mm (1/4 ). Set your straight edge up and clamp in position so the cutter is aligned to the INSIDE of the pencil marking. If you are using a smaller router bit you will need to complete the cut in 2 or more passes. Good idea to check the fit at this stage to make sure the cabinet cheek will fit nicely. Insert the 310 x 450 piece to ensure it fits. Better to be a bit on the snug side rather than a loose fit. 4. Repeat the process for the other 3 division marks. 5. Once one panel has been routed, position the other full size panel next to it (lengthways). Line up the ends, place and clamp straight edge (must be long enough to cover the 2 pieces) in position so as to allow the router to continue the previous rebate across and into the new panel. 6. Select a piece of waste panel or use the 310x450 piece and place into the slot across the 2 panels. This will assist in the alignment of the remaining cuts. Use the straight edge to continue the previously routed channels across into the new panel. 7. Once all 8 channels have been cut, test the fit using the 310x450 piece and place panels to one side. 8. Select 2 of the 310x450 pieces. These pieces will be used as shelf supports. Measured down 90mm. Router a channel across the panel. Use the same router settings as previously.

3 9. Position these 2 panels upright into the middle slots of the large panel you have chosen as the base of your unit. Have the 2 cut shelf rebates facing inwards with the channels on the topside. Stabilise the uprights and make sure they are at 90 degrees to the base. 10. Measure the distance between the bottoms of the 2 slots just cut for the shelf support. Transfer that measurement accurately to the spare panel 650mm and cut to size. 11. Do a dry fit. Place the 2 inside supports into middle rebates, slide in shelf to shelf rebates. Position remaining 2 end supports into base. Place top panel into place and push down onto support uprights. Check for squareness all round and flushness of joints. Make any necessary adjustments and once happy disassemble and glue up. 12. Start with the centre pieces. Glue in the shelf and wipe off any excess glue squeeze out with a damp cloth. Be sure to remove all traces of glue as it can inhibit the staining or finishing process later on. Put to one side making sure to keep it square.

4 13. Glue in and fit 2 end supports onto the base. Tap home with a sacrificial piece of wood and a hammer or mallet. 14. Repeat step 13 on the centre piece with the shelf in position and the other end panel. 15. Apply Selleys Aquadhere Interior to the tops of each upright. Place the top panel of the unit in place. Tap home with sacrificial wood and mallet or hammer. Wash off excess glue with a damp rag. If joints are loose then hold in place (making sure each upright is square) with some sash clamps until glue has set. 16. Measure the outer edge height and width of the unit and subtract 5mm from each measurement.

5 17. Use these measurements to cut the piece of Plywood or backing material to size. 18. Turn the unit over so the face side is resting on the bench. Use a blanket or something soft to protect the surface. As a guide use some masking tape to show where the internal supports run so when the back is in place you can nail with accuracy. 19. Apply a thin bead of Selleys Aquadhere Interior to the rear frame of the Unit. 20. Line up the bottom edge of the back panel to the bottom of the base of the Unit. This will leave a slight gap from the top of the unit to the backing board which is desirable. For extra security hammer in some thin wall nails approx. 400mm apart over the frame. Turn the unit over so that it is lying on its top. 21. To attach feet, apply a bead of Selleys Aquadhere Interior to the inner section of the foot.

6 22. Place the feet into position. Using a piece of scrap wood as a gauge set the feet one thickness in from the front and side edge of the Unit. 23. On the rear or unseen side of the unit the feet have been placed right on the edge of the base. On the front side of the Unit a gap has been left to the edge (18mm) so the feet are not as visible. You may find it necessary to secure the feet into position using a screw in the centre of each foot. If you do this remember to take into consideration the length of the screw used and use one that will hold the foot on but not exit the top of the panel above. 24. Allow the Project to sit until the glue has set. Move into position, fill it up and enjoy.

129 KITCHEN BASE CABINET 480

129 KITCHEN BASE CABINET 480 129 KITCHEN BASE CABINET 480 There are two sorts of kitchen cabinets: base cabinets, which sit on the floor, and wall cabinets. Base cabinets provide both storage space and work surfaces. They often house

More information

COMPLIMENTARY WOODWORKING PLAN

COMPLIMENTARY WOODWORKING PLAN COMPLIMENTARY WOODWORKING PLAN Bookcase This downloadable plan is copyrighted. Please do not share or redistribute this plan in any way. It has been created for Wilton Tools, a division of WMH Tool Group.

More information

Entrance Cabinet Plans

Entrance Cabinet Plans Entrance Cabinet Plans www.andrewharriswoodwork.com Page 1 of 19 Introduction I have tried to ensure all steps are covered in these plans but if you find any errors in the plans or have a question then

More information

WOODWORKING GUIDE: BASIC JOINERY

WOODWORKING GUIDE: BASIC JOINERY WOODWORKING GUIDE: BASIC JOINERY Close isn't really good enough. A perfect fit is what counts. When building furniture, there are many ways to construct joints. The simplest are those that use mechanical

More information

BUILDING A STORM DOOR

BUILDING A STORM DOOR BUILDING A STORM DOOR BY NEAL BARRETT Illustrations by George Retseck If you're in the market for a storm door, you probably know that there are many styles and models available. However, most of them

More information

Extendable Large Dovetail Jig

Extendable Large Dovetail Jig Extendable Large Dovetail Jig Instruction Manual Part # 3458 CAUTION: Please read, understand, and follow all manufacturers instructions, guidelines and owners manuals that come with your power tools.

More information

The WoodWorker s Edge

The WoodWorker s Edge The WoodWorker s Edge Draw-leaf Game Table 1. 2. Layout the area for the tenons. The tenons are 3/8 thick x 4-1/2 long x 1-1/4 deep and offset to the inside. Create the tenons using the step method to

More information

CABINETRY Assembly Instructions

CABINETRY  Assembly Instructions www.hdicabinetry.com Assembly Instructions TABLE OF CONTENTS Category Page(s) Section 1: Framed Series Base Cabinet Instructions Wall Cabinet Instructions Easy Reach Cabinet Instructions 1.01-1.04 1.05-1.06

More information

15 Dovetail Jig. Instruction Manual. Part # 3452

15 Dovetail Jig. Instruction Manual. Part # 3452 15 Dovetail Jig Instruction Manual Part # 3452 CAUTION: Please read, understand, and follow all manufacturers instructions, guidelines and owners manuals that come with your power tools. Peachtree Woodworking

More information

Chess board. The true origins of chess are. from old wood scraps Michael T Collins makes a chessboard and a box to store the pieces

Chess board. The true origins of chess are. from old wood scraps Michael T Collins makes a chessboard and a box to store the pieces What you will need: Combination plane with 3mm, 6mm and 13mm cutters Rip and cross cut saw Block and jack plane Marking gauge and knife Card scraper optional and try square Chess board from old wood scraps

More information

Materials and Tools: Printer s Triple Console Cabinet. Free Plans to build a Triple Console Cabinet

Materials and Tools: Printer s Triple Console Cabinet. Free Plans to build a Triple Console Cabinet Materials and Tools: Materials: 3 sets euro style bottom corner mount drawer slides, 16 length 3 sets inset hinges 24 cup style handles 8 2x2 @ 8 feet long 6 1x3 @ 8 feet long 6 1x2 @ 8 feet long 1 sheet

More information

GENERAL NOTES: Page 1 of 9

GENERAL NOTES: Page 1 of 9 Laminating A Zia Into A Turning Blank by W. H. Kloepping, Jan. 2009 This describes how a zia (the New Mexico state symbol) can be laminated into a turning blank. Materials needed: Square Turning Block

More information

Klamp Trak. Instructions (39052)

Klamp Trak. Instructions (39052) Klamp Trak TM Instructions (39052) ITEM# KKS1020 - Klamp Trak TM Getting Started There are three main methods for installing Klamp Trak in your workshop. In all three methods, your goal will be to construct

More information

EXTREME LOAD no. TWO

EXTREME LOAD no. TWO 1602 - EXTREME LOAD no. TWO Kit Features: 22' 4 " x 14' x 3'-6 Oversize Load 49mm (1.9") actual height Bolt Head Details Welded Load Mounting Fins Painting Handles Tools Required: Hobby Knife Tweezers

More information

NEXUS SERIES CABINETS

NEXUS SERIES CABINETS NEXUS SERIES CABINETS STANDARD BASE ASSEMBLY INSTRUCTIONS Also applies to: Galaxy Series, Nexus Series, Ridgeline Series, Statesman Series, and Waterford Series FOR YOUR INFORMATION: These assembly instructions

More information

Grade 11 Woods Lift Lid Coffee Table. Based on Under the big Top from Popular Mechanics Website

Grade 11 Woods Lift Lid Coffee Table. Based on Under the big Top from Popular Mechanics Website Grade 11 Woods Lift Lid Coffee Table Based on Under the big Top from Popular Mechanics Website TABLE TOP 1. Select enough lumber to construct a top that is between 22 ½ and 24 wide after jointing. Ensure

More information

Corner Entertainment Center Plans

Corner Entertainment Center Plans Table of Contents Introduction... 3 Let s discuss the tools needed... 3 Let s discuss the materials needed... 4 Let s build it... 4 Attaching the 2x2's... 7 Determine the shelf spacing... 9 Scribing the

More information

Build your own Drawer unit. D3 / D4

Build your own Drawer unit. D3 / D4 Page1 Build your own Drawer unit. D3 / D4 1: Introduction. This guide will give you the plans, materials and how to information to build your own drawer unit. The dimensions given will fit a D3 or D4,

More information

Hudson Dresser [1] Hudson Dresser Published on Ana White ( Submitted by dan-k [2] on Fri, :43 [1]

Hudson Dresser [1] Hudson Dresser Published on Ana White (  Submitted by dan-k [2] on Fri, :43 [1] [1] Submitted by dan-k [2] on Fri, 2011-03-11 11:43 [1] If you plan on staining this piece, it is recommended that you stain all of the drawer face materials before assembly for a more professional look.

More information

Trestle Table and Benches Materials List

Trestle Table and Benches Materials List Project 18444EZ: Trestle Table and Benches In the early days of our country, trestle tables were popular because they could easily be disassembled and moved out of the way when not in use no small advantage

More information

Woodline USA Woodline Spacer Fence System

Woodline USA Woodline Spacer Fence System Woodline USA Woodline Spacer Fence System MADE IN THE USA Includes: (1) ¼ Spacer Fence (1) 3/8 Spacer Fence (1) ½ Spacer Fence (1) Hardware Package (1) 3 Piece Brass bar set (2) Setup Blocks Visit Us Online

More information

Australian Vintage Radio Society Inc.

Australian Vintage Radio Society Inc. Australian Vintage Radio Society Inc. (Incorporated in Victoria A0050003S) P.O. Box 3099, Syndal L.P.O., Victoria, 3150, Australia. Cabinet assembly instructions for the AVRS 10 th Anniversary construction

More information

Chest of Drawers Plans

Chest of Drawers Plans Chest of Drawers Plans www.andrewharriswoodwork.com Page 1 of 15 Introduction This plan makes a chest of drawers that is 50 inches at the widest point, 19 inches deep and 40.75 inches high. I have tried

More information

Contents. pages 20-24: Installing Edge sinks into. custom laminate countertops page 8: Installing Edge sinks into postform laminate countertops

Contents. pages 20-24: Installing Edge sinks into. custom laminate countertops page 8: Installing Edge sinks into postform laminate countertops Contents pages 2-8: Installing Edge sinks into custom laminate countertops page 8: Installing Edge sinks into postform laminate countertops pages 9-14: Installing Acrylic sinks into custom laminate countertops

More information

The Ultimate Storage Cart Tutorial

The Ultimate Storage Cart Tutorial The Ultimate Storage Cart Tutorial TOOLS Table saw (or circular saw and straight edge) (alternatively, a good hardware store could make these cuts for you) Router with 1/2 bit Straight edge Clamps Screwdriver

More information

SE5a Instrument Board part 2 - rev 1.1

SE5a Instrument Board part 2 - rev 1.1 SE5a Instrument Board part 2 - rev 1.1 Fuel (Petrol) Valve This valve uses two circular name plates, eight brass screws, one black plastic base, copper wire and two black plastic risers. You can pick any

More information

Xenon 05 Installation Instructions & Parts List

Xenon 05 Installation Instructions & Parts List Xenon 05 Installation Instructions & Parts List Illustration Xenon 05, H1 Handle Left Hand: Open Out 26/05/2016 Revision 2.1 Page 1 of 19 IMPORTANT This shower screen / enclosure must be installed by suitably

More information

Installing your new Bevella Top. L Shaped Countertop with Joints No Finished Ends (Fits Between Four Walls)

Installing your new Bevella Top. L Shaped Countertop with Joints No Finished Ends (Fits Between Four Walls) Installing your new Bevella Top L Shaped Countertop with Joints No Finished Ends (Fits Between Four Walls) Bevella RTI Countertops are engineered and manufactured to the highest quality standards, built

More information

Somewhere along the way, we ve

Somewhere along the way, we ve Precision 60 FINEHOMEBUILDING.com Window Trim A systematic approach ensures better joints and a faster installation By Anthony Vitale Somewhere along the way, we ve decided that it s the apprentice s job

More information

Silverware Chest Plan

Silverware Chest Plan Silverware Chest Plan 05L14.01 Introduction 1. Measure the space required for your cutlery before beginning this project to be sure that it will fit in the drawers and top compartment. The best way to

More information

BBQ Trolley. 25 oiam. 240 oiam. 19

BBQ Trolley. 25 oiam. 240 oiam. 19 BBQ Trolley Written and constructed by Craig Tilley This trolley makes a very handy outdoor barbecue trolley. lt's also a great showpiece and functional drinks tray for the patio when entertaining. The

More information

Bathroom Storage Unit. Wilkerdos.com

Bathroom Storage Unit. Wilkerdos.com Bathroom Storage Unit Wilkerdos.com Copyright 2015 Material List Quantity Item Notes 1 4 x 8 x 3/4 plywood Construction grade 1 2 x 4 x 1/2 plywood Construction grade 11" 7-1/2" Page 1 Some 1 1/4" brad

More information

Demilune 4. Apron Joinery. Curved Apron Tenon. Bridle Joint Legs. Bridle Joint Front Apron

Demilune  4. Apron Joinery. Curved Apron Tenon. Bridle Joint Legs. Bridle Joint Front Apron Demilune Email 4 Apron Joinery There are two types of joints used in connecting the aprons and legs. The rear legs use conventional mortise and tenon joints, while the front legs use the less conventional

More information

End-On-End Dovetails D4R - CHAPTER 12

End-On-End Dovetails D4R - CHAPTER 12 D4R - CHAPTER End-On-End Dovetails 4 While you have the router set up for half-blind dovetails, it is a good time to try end-on-end dovetails. If you have not yet routed half-blind dovetails or read through

More information

136 PLYWOOD DESK 522

136 PLYWOOD DESK 522 136 PLYWOOD DESK 522 Simple in design and inexpensive, this plywood desk is made from a single 4- x 8-foot panel. Plywood is available with many hardwood veneers; it can also be covered with plastic laminate,

More information

Shelf Divider Top Panel. Trim Piece

Shelf Divider Top Panel. Trim Piece Page 1 Shelf Divider Top Panel SCAN FOR ASSEMBLY VIDEO Side Panel Long Shelf Panel Side Panel Bottom Panel Trim Piece Package Contents *Please verify that you have the correct number of parts before proceeding.

More information

Plans. Easy-to-Build Full-size Deluxe Murphy Bed Plan. For more plans, tools and hardware visit rockler.com

Plans. Easy-to-Build Full-size Deluxe Murphy Bed Plan. For more plans, tools and hardware visit rockler.com Easy-to-Build Full-size Deluxe Murphy Bed Plan Build a full-size Deluxe Murphy Bed complete with decorative molding and matching side cabinets! Plans For more plans, tools and hardware visit rockler.com

More information

Making Simple Bookbinding Equipment. A Lying Press. Making Simple Bookbinding Equipment. A Lying Press. Tony Firman

Making Simple Bookbinding Equipment. A Lying Press. Making Simple Bookbinding Equipment. A Lying Press. Tony Firman Making Simple Bookbinding Equipment Tony Firman 28 1 2 27 Notes Making Simple Bookbinding Equipment Tony Firman Tony Firman Bookbinding 26 3 Making Simple Bookbinding Equipment: 2012 Tony Firman Bookbinding

More information

Art Rack Assembly Instructions:

Art Rack Assembly Instructions: Art Rack Assembly Instructions: ** PIECES ARE POWDER COATED Do not lay pieces on top of each other or on a hard, rough surface if possible. All bolts will pass from outside towards inside of the cage.

More information

CHAPTER 8. Through Dovetail Procedures

CHAPTER 8. Through Dovetail Procedures CHAPTER Through Dovetail Procedures 52 Chapter D4 User Guide THROUGH DOVETAIL PROCEDURES Chapter Foreword In these instructions for using the Leigh Dovetail Jig, we have recommended using certain cutters

More information

Scissor Stool. Written By: Feitan

Scissor Stool. Written By: Feitan Scissor Stool If the stool is going to be kept indoors simply rub all the pieces with a Minwax WipeOn Poly before assembling the stool. If it is going to go outdoors use Minwax SparUrathane and coat all

More information

woodworkersjournal.com MATERIAL LIST

woodworkersjournal.com MATERIAL LIST MATERIAL LIST T x W x L 1 Legs (2) 1 1 2" x 3 1 2" x 36 7 16" 2 End Uprights (2) 1 1 2" x 3 1 2" x 32 1 2" 3 Stringers (4) 1 1 2" x 3 1 2" x 42" 4 Top Cladding, Long (2) 3/4" x 7 1 4" x 65 3 4" 5 Side

More information

DIY Wine Storage Cabinet

DIY Wine Storage Cabinet DIY Wine Storage Cabinet ADDICTED2DIY.COM *Before beginning this project, please read through all of the plans and the blog post. When building this project, be sure to measure your wood and cut to fit.

More information

Copyright 2010 Springbok Publishing All Rights Reserved- Page 1

Copyright 2010 Springbok Publishing All Rights Reserved-   Page 1 Copyright 2010 Springbok Publishing All Rights Reserved- www.woodensaddlerackplans.com Page 1 Legal Information All contents copyright 2010 by Springbok Publishing. All rights reserved. No part of this

More information

Step-by-Step Instructions for Making the Wall-hung Bookcase

Step-by-Step Instructions for Making the Wall-hung Bookcase Step-by-Step Instructions for Making the Wall-hung Bookcase When a piece of furniture has an air and look of simplicity, you can be sure that it deftly conceals the complexity of its making. I wanted this

More information

Curium 19.4H Installation Instructions & Parts List

Curium 19.4H Installation Instructions & Parts List Curium 19.4H Installation Instructions & Parts List Illustration Curium 19.4H Right Hand Page 1 of 21 30/06/2016 Revision 1.0 IMPORTANT This shower screen / enclosure must be installed by suitably qualified

More information

Mid-Century Credenza Thoughtful details and modern joinery merge in this sleek design

Mid-Century Credenza Thoughtful details and modern joinery merge in this sleek design Mid-Century Credenza Thoughtful details and modern joinery merge in this sleek design BY LIBBY SCHRUM Mid-Century Modern furniture has not been wildly popular since, well, the mid-century. But fashion

More information

ARTS AND CRAFTS CHAIR

ARTS AND CRAFTS CHAIR ARTS AND CRAFTS CHAIR 491 MATERIALS LIST--DINING CHAIR Key No. Size and description (use) A 2 1-3/4 x 1-3/4 x 16-1/4'' oak (front leg) B 2 1-3/4 x 3-3/4 x 40-1/2'' oak (rear leg) C 1 1-3/4 x 3-3/16 x 15''

More information

A H M 531 The Civil Engineering Center

A H M 531 The Civil Engineering Center Table of Contents contents Page Introduction 1 Objectives 2 Background 2 Apparatus and tools 3 Requirements 5 Procedures 6 Conclusion 10 References 10 1 Introduction Carpentry work is one of the most important

More information

Gallium 03 Installation Instructions & Parts List

Gallium 03 Installation Instructions & Parts List Gallium 03 Installation Instructions & Parts List Illustration Gallium 03, H1 Handle Left Hand: Open Out 04/05/2016 Revision 1.1 Page 1 of 19 IMPORTANT This shower screen / enclosure must be installed

More information

Installing your SHOE KEEL

Installing your SHOE KEEL Installing your SHOE KEEL The shoe keel is there solely to protect the bottom of the hull. On a windy day, it will offer some resistance to a side or quartering wind and will help to avoid being blown

More information

Dubnium 11 Installation Instructions & Parts List

Dubnium 11 Installation Instructions & Parts List Dubnium 11 Installation Instructions & Parts List Illustration Dubnium, H1 Handle Right Hand: Open Out Page 1 of 25 IMPORTANT This shower screen / enclosure must be installed by suitably qualified individuals.

More information

Shaker Shop Stool. By Glen D. Huey

Shaker Shop Stool. By Glen D. Huey Shaker Shop Stool By Glen D. Huey By the turn of the decade following Mother Ann Lee s visit in 1783, the Massachusetts Shaker community known as Hancock began its existence. From a small gathering of

More information

Install Instructions for Torrance Jurastone #4004 Mantel

Install Instructions for Torrance Jurastone #4004 Mantel Install Instructions for Torrance Jurastone #4004 Mantel Please read this manual before installing the suite. This manual should remain with the homeowner. 20/05/11 Fires of Tradition assumes no responsibility

More information

Robert Bosch GmbH. Minimalist washstand

Robert Bosch GmbH. Minimalist washstand Minimalist washstand Neat and tidy Minimalist washstand Minimalist design in the bathroom is in fashion. And rightly so, as this washstand proves: because less is more! 1 Introduction Here s an idea to

More information

G. Building the Cab, Cab Roof and Cab Boiler Extension Page 14 and Backhead.

G. Building the Cab, Cab Roof and Cab Boiler Extension Page 14 and Backhead. G. Building the Cab, Cab Roof and Cab Boiler Extension Page 14 and Backhead. Cab. In order to ensure that the cab and tender would actually look right, as what often appears on a drawing is not always

More information

REINFORCING THE CORNERS OF FLAT FRAMES

REINFORCING THE CORNERS OF FLAT FRAMES REINFORCING THE CORNERS OF FLAT FRAMES There are a number of different methods that may be used to join flat frame sides together. As most Woodworkers know, end grain glue joints are not nearly as strong

More information

Building and installing dividing walls, by Tobias Sternberg

Building and installing dividing walls, by Tobias Sternberg Building and installing dividing walls, by Tobias Sternberg This instruction sets out to show one way to build and install simple dividing walls for studio spaces. I have written it as clearly as possible.

More information

Pergola. How To Build A. ***Safety First*** Please read the section on workplace safety at the end of this manual before proceeding with any work.

Pergola. How To Build A. ***Safety First*** Please read the section on workplace safety at the end of this manual before proceeding with any work. How To Build A Pergola ***Safety First*** Please read the section on workplace safety at the end of this manual before proceeding with any work. How To Build A Pergola Pergolas can be built to many different

More information

COMPLIMENTARY WOODWORKING PLAN

COMPLIMENTARY WOODWORKING PLAN COMPLIMENTARY WOODWORKING PLAN COFFEE TABLE PLAN This downloadable plan is copyrighted. Please do not share or redistribute this plan in any way. It has been paid for on your behalf by JET Tools, a division

More information

installation care & maintenance instructions lifecycledecking.com 25-year limited residential warranty 20-year limited commercial warranty

installation care & maintenance instructions lifecycledecking.com 25-year limited residential warranty 20-year limited commercial warranty installation care & maintenance instructions lifecycledecking.com 25-year limited residential warranty 20-year limited commercial warranty Installation Instructions As with any building project, use proper

More information

Framework joints FABRICATION - WOOD JOINTS. Corner joints. Tee joints. Worksheet 15a. Cable Educational Ltd

Framework joints FABRICATION - WOOD JOINTS. Corner joints. Tee joints. Worksheet 15a. Cable Educational Ltd FABRICATION - WOOD JOINTS The word: fabricate means to join together. Most wooden products are held together with adhesive. Adhesive works very well when the edge of a piece of wood is being glued to the

More information

America s leading woodworking authority To download these plans, you will need Adobe Reader installed on your computer. If you want to get a free copy, visit: http://adobe.com/ reader. Having trouble downloading

More information

Curium 19H Installation Instructions & Parts List

Curium 19H Installation Instructions & Parts List Curium 19H Installation Instructions & Parts List Illustration Curium 19H Right Hand Page 1 of 15 01/07/2016 Revision 2.1 IMPORTANT This shower screen / enclosure must be installed by suitably qualified

More information

COMPLIMENTARY WOODWORKING PLAN

COMPLIMENTARY WOODWORKING PLAN COMPLIMENTARY WOODWORKING PLAN ORIENTAL GARDEN ARBOR PLAN This downloadable plan is copyrighted. Please do not share or redistribute this plan in any way. It has been paid for on your behalf by JET Tools,

More information

1 ¼-inch Pocket Screws Brad Nailer or Hammer 1 ¼-inch Brad Nails Clamps

1 ¼-inch Pocket Screws Brad Nailer or Hammer 1 ¼-inch Brad Nails Clamps MATERIALS: TOOLS: (4) 2 x 6 x 8 Ft. Boards Tape Measure (2) 2 x 4 x 8 Ft. Boards Carpenter s Square (7) 1 x 4 x 8 Ft. Boards Pencil (2) 1 x 3 x 8 Ft. Boards Drill (1) Half Sheet of ¾-inch Thick Plywood

More information

Empire Dresser Plans

Empire Dresser Plans 1 Empire Dresser Plans Materials 1 sheet 3/4" plywood (cabinet grade 4' x 8') 1 sheet 5 mm (3/16") underlayment plywood 4'x 8', buy another 1/2 sheet if you want to put a back on the dresser. 1-2" x 4"

More information

Sideboard. Essential design. Sideboard Unique eye-catcher and practical storage space all at once: The sideboard with fashionable multimaterial

Sideboard. Essential design. Sideboard Unique eye-catcher and practical storage space all at once: The sideboard with fashionable multimaterial Sideboard Essential design. Sideboard Unique eye-catcher and practical storage space all at once: The sideboard with fashionable multimaterial design. 1 Introduction From multi-material to one of a kind!

More information

Project Skill Level: INTERMEDIATE Plywood Used: CANPLY EXTERIOR Good Two Sides (G2S) or precision sanded Aspen

Project Skill Level: INTERMEDIATE Plywood Used: CANPLY EXTERIOR Good Two Sides (G2S) or precision sanded Aspen Project Skill Level: INTERMEDIATE Plywood Used: CANPLY EXTERIOR Good Two Sides (G2S) or precision sanded Aspen MATERIALS LIST: (1) ¾" x 4 ft x 8 ft plywood panel (20) #8 x 2" Robertson or Phillips wood

More information

Making a Massive Bookcase Step-by-Step

Making a Massive Bookcase Step-by-Step Making a Massive Bookcase Step-by-Step Jeff Branch WOODWORKING The only thing challenging about this project is its huge size. By JFF BRANCH A t right is a rendering of my first woodworking project completed

More information

The Q Frame PROJECT. a picture frame with secrets created exclusively for the Router Forum

The Q Frame PROJECT. a picture frame with secrets created exclusively for the Router Forum The Q Frame PROJECT a picture frame with secrets created exclusively for the Router Forum 007 OR RELEASE FPLANS APPROVED The Q Frame: Project Overview LIST OF MATERIALS Frame Sides & Face 3/4 x 5 1/2 x

More information

Bird Feeder. Tool Requirements

Bird Feeder. Tool Requirements Bird Feeder Written and constructed by Craig Tilley This wooden bird feeder will be an attractive addition to your garden. Its wide trays allow plenty of room for birds to come and have a snack, and the

More information

EZYSTONE WORKSURFACES

EZYSTONE WORKSURFACES EZYSTONE WORKSURFACES Installation & Maintenance Instructions 1. Tools Required Worktop Edge Finishing Kit Pack 1-100mm Velcro Backing Pad Pack 2-100mm Diamond Dry Cut Velcro Discs (100 Grit Yellow) (200

More information

installation care & maintenance instructions moistureshield.com limited lifetime warranty

installation care & maintenance instructions moistureshield.com limited lifetime warranty installation care & maintenance instructions 866.729.2378 moistureshield.com limited lifetime warranty It s comforting to know that you re about to build a deck that gives you every possible advantage.

More information

Coffee table with recessed tray

Coffee table with recessed tray Coffee table with recessed tray Dinner is served Coffee table with recessed tray This coffee table has it all: it contains a recessed tray, so that you can treat your guests to various delicacies. 1 Introduction

More information

About.com :

About.com : http://woodworking.about.com/gi/dynamic/offsite.htm?sit...//www.popularwoodworking.com/features/fea.asp%3fid=1088 (1 of 8)1/28/2004 12:05:01 AM Modern Storage Tower The last thing I want to do when starting

More information

COFFEE TABLE WITH RECESSED TRAY

COFFEE TABLE WITH RECESSED TRAY COFFEE TABLE WITH RECESSED TRAY Why not treat your guests to a tray laid with delicacies and then remove it from sight in your new coffee table. There's no easier way to show that you are a thoughtful

More information

VCE VET FURNISHING (CABINET MAKING)

VCE VET FURNISHING (CABINET MAKING) Victorian Certificate of Education 2012 SUPERVISOR TO ATTACH PROCESSING LABEL HERE STUDENT NUMBER Letter Figures Words VCE VET FURNISHING (CABINET MAKING) Written examination Section Monday 12 November

More information

Kitchen Step Stool. Premium Plan. In this plan you ll find: America s leading woodworking authority

Kitchen Step Stool. Premium Plan. In this plan you ll find: America s leading woodworking authority America s leading woodworking authority Premium Plan In this plan you ll find: Step-by-step construction instruction. A complete bill of materials. Construction drawings and related photos. Tips to help

More information

BONDO PROCESS. Installation Guide.

BONDO PROCESS. Installation Guide. BONDO PROCESS Installation Guide www.karran.com BONDO PROCESS This Installation Guide demonstrates simple methods and proven techniques for seamlessly installing Karran undermount sinks in laminate countertops.

More information

INSTALLATION GUIDE SLIMLINE ROOF LANTERN 4 PANE CONFIGURATION

INSTALLATION GUIDE SLIMLINE ROOF LANTERN 4 PANE CONFIGURATION INSTALLATION GUIDE SLIMLINE ROOF LANTERN 4 PANE CONFIGURATION SLIMLINE STEP-BY-STEP INSTALLATION GUIDE Thank you for choosing Roof Maker, we hope you are delighted with your new rooflight. Our roof lanterns

More information

Serving Tray. When some good friends got married recently, An exercise in template-making yields a great gift project that s easy to duplicate

Serving Tray. When some good friends got married recently, An exercise in template-making yields a great gift project that s easy to duplicate Serving Tray An exercise in template-making yields a great gift project that s easy to duplicate END Create from 3 8 2 8" piece. By Geoff Noden When some good friends got married recently, I decided to

More information

You Can Build a Bedside Table

You Can Build a Bedside Table You Can Build a Bedside Table Jeff Branch WOODWORKING If you like making panels, you ll love this project. By JEFF BRANCH M y current home is a modest one. But it is a big improvement over our small starter

More information

Install Instructions for Solano Jurastone #4012 Mantel

Install Instructions for Solano Jurastone #4012 Mantel Install Instructions for Solano Jurastone #4012 Mantel Please read this manual before installing the suite. This manual should remain with the homeowner. Updated 12/03/12 NOTE the installation requirements

More information

4 Column Display Row Corner

4 Column Display Row Corner 4 Column Display Row Corner Page 1 IMPORTANT! If you purchased a 2 Column Display Row Corner Kit, your package will contain the following parts: END LADDER ASSEMBLIES - x4 1 COLUMN SCREWLESS CONNECTORS

More information

Harriet Chair with Modifications

Harriet Chair with Modifications Harriet Chair with Modifications This modification of the Harriet chair includes a slat back, padded seat, and is 2 inches wider than the original plan. The overall dimensions of the finished chair: 38

More information

Copyright WilkerDos.com Dining Table. Project Designed By April Wilkerson - Plan Created By Jay Bates (jayscustomcreations.

Copyright WilkerDos.com Dining Table. Project Designed By April Wilkerson - Plan Created By Jay Bates (jayscustomcreations. Copyright WilkerDos.com 2017 Project Designed By April Wilkerson - Plan Created By Jay Bates (jayscustomcreations.com) Layout & Shopping List Page 2 of 12 Layout & Shopping List Item Quantity Description

More information

Lock on! Chris Tribe shows you how to cut a lock into the back of a door and fit an escutcheon

Lock on! Chris Tribe shows you how to cut a lock into the back of a door and fit an escutcheon Technique Lock on! Chris Tribe shows you how to cut a lock into the back of a door and fit an escutcheon Pic.1 Chris fitted this oak display cabinet with a cut lock and covered his precise work with a

More information

THE PODIUM MUSIC STAND

THE PODIUM MUSIC STAND THE PODIUM MUSIC STAND 1 Set Assembly Instructions Wooden Parts: a. 1 Column b. 2 Long Slide Pieces c. 2 Slide Spacers (1 long & 1 short) d. 4 Feet e. 2 Fork Pieces f. 1 Fork Spacer g. 2 Long Desk Frame

More information

While creating a two-wall

While creating a two-wall Ready-To-Assemble Cabinets Outfit your shop in a weekend or less. By Gary Lombard with Jim Harrold 32 woodcraftmagazine.com Aug/Sept 2013 While creating a two-wall or larger shop (or a kitchen, for that

More information

Materials. Special Tools and Techniques Chisel Long pipe clamps Miters Router with 1/2" rabbet cutter Rabbets Dadoes. Hardware

Materials. Special Tools and Techniques Chisel Long pipe clamps Miters Router with 1/2 rabbet cutter Rabbets Dadoes. Hardware D esk Our executive desk was built with specific needs in mind. We wanted a large desktop, large drawers, and a cubbyhole to house a rollaway hanging file cabinet. We are thrilled with our finished project.

More information

ining Table Materials *Notes on Materials

ining Table Materials *Notes on Materials D ining Table We looked around for the perfect table for the dining room. Some were too big, some too small, and most were just too expensive. So we built this one, and we are happy with the result. It

More information

Instructables Butcher Block Top

Instructables Butcher Block Top Instructables Butcher Block Top Project Overview: This project requires basic woodworking skills and access to woodworking machines. Woodworking machines have sharp cutting edges and are NOT forgiving.

More information

Radon 07 Installation Instructions & Parts List

Radon 07 Installation Instructions & Parts List Radon 07 Installation Instructions & Parts List Illustration Radon 07, H1 Handle Right Hand: Open Out 14/06/2016 Revision 1.1 Page 1 of 21 IMPORTANT This shower screen / enclosure must be installed by

More information

Build a Rolling Tool Tote

Build a Rolling Tool Tote The rolling tool tote design calls for readily available materials: a cheap hand truck (it could be an axle and two wheels), 3/4 and 1/2 thick plywood, 1/4 thick MDF (you could use plywood or hardboard)

More information

Continue gluing the remaining top parts ensuring the angled piece is glued well. Set aside and let dry. See photo below

Continue gluing the remaining top parts ensuring the angled piece is glued well. Set aside and let dry. See photo below Radiator rev 1.1 The SE5a s radiator is one of the most recognized radiators in WW1. It is one of the components that defines the SE5a. The original SE5a has seen multiple radiator designs used during

More information

PORCH-LOC INSTALLATION INSTRUCTIONS

PORCH-LOC INSTALLATION INSTRUCTIONS PORCH-LOC INSTALLATION INSTRUCTIONS 2017 HB&G Building Products, Inc. Porch-Loc Installation Instructions NOTE: DISCARD THE INSTALLATION INSTRUCTIONS AND HARDWARE THAT CAME IN YOUR PERMAPOST PACKAGING

More information

ENJOY THIS SELECTION FROM. Woodworking 101. Includes Step-by-Step Instructions for 8 Projects. Woodworking

ENJOY THIS SELECTION FROM. Woodworking 101. Includes Step-by-Step Instructions for 8 Projects. Woodworking W ENJOY THIS SELECTION FROM Woodworking 101 Includes Step-by-Step Instructions for 8 Projects Woodworking 101 Aimé Fraser, Matthew Teague, and Joe Hurst-Wajszczuk To purchase your copy of Woodworking 101,

More information

Scratchbuild A Backwoods Water Tank Part V - Making the Frost Box and Hanging the Water Spout

Scratchbuild A Backwoods Water Tank Part V - Making the Frost Box and Hanging the Water Spout Scratchbuild A Backwoods Water Tank Part V - Making the Frost Box and Hanging the Water Spout By Dwight Ennis In this section, we're going to make the Frost Box, and we'll build the Spout Hanger Assembly

More information

Installation Guide. Deckorum. Composite Decking

Installation Guide. Deckorum. Composite Decking Installation Guide Deckorum Composite Decking 1. Introduction Welcome to Deckorum Installation Guide Please fully read the installation guide before commencing any installation works. This will provide

More information