PLAN, SECTION, ISOMETRIC: OBJECT
|
|
- Branden Dixon
- 5 years ago
- Views:
Transcription
1 ISOMETRIC #5a PLAN, ELEVATION, ISOMETRIC Draft due Monday, October 15 correct & precise Redraft with Ink Due Monday October 22 On a sheet of 18"x24" strathmore, compile a set of drawings of a small object with cylindrical and/or conical form. First draw the PLAN and SECTION of the object to aid the drawing of 2 ISOMETRICS, one of the object in VERTICAL position, and one of the object in a HORIZONTAL position. OBSERVE & MEASURE To begin, sketch a diagram of the object and use a ruler to find its measurements. Take measurements for all primary elements, and all points of inflections on the object's external contour. DETERMINE DRAWING LAYOUT & SCALE You may not be able to fit all the drawings of the object on the page at real size (scale: 1"=1"). You may need to scale the drawing. For example you might determine that you can use 1/2" = 1" scale. (This would effectively shrink the object's size in half.) The page will be divided into four sections. Object Drawing Set
2 ISOMETRIC #5b DRAWING RELATIONSHIPS The plan will stack directly above the section. Construction lines clearly demonstrate that the widths of the plan and the section are the same. Stack the horizontal iso over the vertical iso. Align the edge of the vertical iso with the elevation, and align the horizontal iso with the plan. Using construction lines, sketch out the size and placement of all four drawings.
3 ISOMETRIC #5c SECTION Begin the section by drawing the overall size envelope as a rectangle or square. Add measured tickmarks to the boxes edges to use these as MEASUREMENT LINES in your drawing's scale. Draw diagonals to find the center of the section, and draw the midline (AXIS of SYMMETRY) Add CONSTRUCTION LINES for all object's major contour inflections. PLAN Draw the plan. Include: RECTILINEAR ENVELOPE MEASUREMENT TICKMARKS DIAGONALS MIDLINES (AXES) CONTOUR'S CONSTRUCTION LINES CONTOUR LINES HIDDEN LINES Lightly sketch in the object exterior and interior contours. Use LINEWEIGHT to enhance the drawing's legibility. Solid ink for visible contours, dotted ink for hidden lines and additional structural contours.
4 ISOMETRIC #5d VERTICAL ISOMETRIC Set up the rectilinear wireframe for your isometric drawing. Connect exterior contour lines from midpoints to midpoints. Transfer measurement tickmarks to the edges. Start by drawing a horizontal plane at every major contour inflection or connection between parts, on the section. Using measurements and construction lines, determine the cross-sections of the object in each plane. Finish the drawing by increasing its legibility through inked lineweights, solid and dotted.
5 ISOMETRIC #5e HORIZONTAL ISOMETRIC Use TRACE PAPER to cover up the vertical isometric to keep it clean while you draw above. Set up the rectilinear wireframe for your isometric drawing. Using measurements and construction lines, determine the crosssections of the object in each plane. Transfer measurement tickmarks to the edges. Start by drawing a vertical plane at every major contour inflection or connection between parts, on the elevation. Also draw the axial planes through the midpoint to help you visualize the object's center axis. Connect exterior contour lines from midpoints to midpoints.
6 ISOMETRIC #5f ISOMETRIC FORM: OBJECT HORIZONTAL ISOMETRIC, CONT. Connect exterior contour lines from midpoints to midpoints. Finish the drawing by increasing its legibility through inked lineweights, solid and dotted. Complete Drawing Set
Pictorial Drawings. DFTG-1305 Technical Drafting Prepared by Francis Ha, Instructor
DFTG-1305 Technical Drafting Prepared by Francis Ha, Instructor Pictorial Drawings Geisecke s textbook for reference: 14 th Ed. Ch. 15: p. 601 Ch. 16: p. 620 15 th Ed. Ch. 14: p. 518 Ch. 15: p. 552 Update:
More information1: Assemblage & Hierarchy
What: 1: Assemblage & Hierarchy 2 compositional sequences o abstract, line compositions based on a 9 square grid o one symmetrical o one asymmetrical Step 1: Collage Step 2: Additional lines Step 3: Hierarchy
More informationThe Ellipse. PF 1 + PF 2 = constant. Minor Axis. Major Axis. Focus 1 Focus 2. Point 3.4.2
Minor Axis The Ellipse An ellipse is the locus of all points in a plane such that the sum of the distances from two given points in the plane, the foci, is constant. Focus 1 Focus 2 Major Axis Point PF
More information11/12/2015 CHAPTER 7. Axonometric Drawings (cont.) Axonometric Drawings (cont.) Isometric Projections (cont.) 1) Axonometric Drawings
CHAPTER 7 1) Axonometric Drawings 1) Introduction Isometric & Oblique Projection Axonometric projection is a parallel projection technique used to create a pictorial drawing of an object by rotating the
More information1. Open the Feature Modeling demo part file on the EEIC website. Ask student about which constraints needed to Fully Define.
BLUE boxed notes are intended as aids to the lecturer RED boxed notes are comments that the lecturer could make Control + Click HERE to view enlarged IMAGE and Construction Strategy he following set of
More informationDescribing an Angle Bracket
Basics of Drafting Describing an Angle Bracket Orthographic Projection Orthographic drawings represent three dimensional objects in three separate views arranged in a standard manner. Orthographic Views
More informationENGR 1182 Exam 1 First Mid Term Exam Study Guide and Practice Problems
Spring Semester 2016 ENGR 1182 Exam 1 First Mid Term Exam Study Guide and Practice Problems Disclaimer Problems in this study guide resemble problems relating mainly to the pertinent homework assignments.
More informationChapter 8. Technical Drawings
Chapter 8 Technical Drawing Technical Drawings Multiview drawings Also called three-view drawings Simple objects take three views Front, top, one side Title block Identifies who did the design Gives date,
More informationDMT113 Engineering Drawing. Chapter 3 Stretch System
DMT113 Engineering Drawing Chapter 3 Stretch System Contents Theory & Multiview Planes 6 Principle Views Multiview Sketching Technique & Perspective First & Third Angle Multiview Representations Theory
More informationUNIT 5a STANDARD ORTHOGRAPHIC VIEW DRAWINGS
UNIT 5a STANDARD ORTHOGRAPHIC VIEW DRAWINGS 5.1 Introduction Orthographic views are 2D images of a 3D object obtained by viewing it from different orthogonal directions. Six principal views are possible
More informationME1105 Engineering Drawing & Design
City University London Term 1 Assessment 2008/2009 School of Engineering and Mathematical Sciences ME1105 Engineering Drawing & Design Student Name:.., Group: Examination duration: Reading time: This paper
More informationReavis High School Curriculum Snapshot/Cover Page for Computer Aided Design (CAD)
Reavis High School Curriculum Snapshot/Cover Page for Computer Aided Design (CAD) Unit 1: Introduction In this unit, students will identify components of a Computer Aided Design (CAD) system and how to
More informationAt the conclusion of this unit you should be able to accomplish the following with a 70% accuracy
7 Multiview Drawing OBJECTIVES At the conclusion of this unit you should be able to accomplish the following with a 70% accuracy 1. explain the importance of mulitview drawing as a communication tool far
More informationORTHOGRAPHIC PROJECTION
ORTHOGRAPHIC PROJECTION C H A P T E R S I X OBJECTIVES 1. Recognize and the symbol for third-angle projection. 2. List the six principal views of projection. 3. Understand which views show depth in a drawing
More informationIsometric Drawing (Architectural Board drafting)
Design and Drafting Description Isometric drawings use perspective to communicate a large amount of information in a single drawing. Isometric drawings show three sides of an object, making it easier to
More informationCopyrighted Material. Copyrighted Material. Copyrighted. Copyrighted. Material
Engineering Graphics ORTHOGRAPHIC PROJECTION People who work with drawings develop the ability to look at lines on paper or on a computer screen and "see" the shapes of the objects the lines represent.
More information2018 Technical Drawing Specifications Resource A guide to support VCE Visual Communication Design Study Design
2018 Technical Drawing Specifications Resource A guide to support VCE Visual Communication Design Study Design 2018 22 VICTORIAN CURRICULUM AND ASSESSMENT AUTHORITY 1 Contents A guide to support VCE Visual
More informationChapter 1 Overview of an Engineering Drawing
Chapter 1 Overview of an Engineering Drawing TOPICS Graphics language Engineering drawing Projection methods Orthographic projection Drawing standards TOPICS Traditional Drawing Tools Lettering Freehand
More informationCE 100 Civil Engineering Drawing Sessional (Lab Manual)
CE 100 Civil Engineering Drawing Sessional (Lab Manual) Department of Civil Engineering Ahsanullah University of Science and Technology November, 2017 1 Preface This course is designed to provide civil
More informationUnit 6 Task 2: The Focus is the Foci: ELLIPSES
Unit 6 Task 2: The Focus is the Foci: ELLIPSES Name: Date: Period: Ellipses and their Foci The first type of quadratic relation we want to discuss is an ellipse. In terms of its conic definition, you can
More informationModeling an Airframe Tutorial
EAA SOLIDWORKS University p 1/11 Difficulty: Intermediate Time: 1 hour As an Intermediate Tutorial, it is assumed that you have completed the Quick Start Tutorial and know how to sketch in 2D and 3D. If
More informationOrthographic Drawing (Architectural Board Drafting)
Design and Drafting Description In this activity, the teacher will introduce orthographic projection, in which a multi-view drawing shows how the sides of an object are related to each another. Students
More informationtechnical drawing
technical drawing school of art, design and architecture nust spring 2011 http://www.youtube.com/watch?v=q6mk9hpxwvo http://www.youtube.com/watch?v=bnu2gb7w4qs Objective abstraction - axonometric view
More informationOrthographic Projection
ENG3000 Orthographic Projection 1 Session Objectives To understand the basic principles of orthographic projection To be able to construct orthographic views of simple objects To visualize 3 D objects
More informationORTHOGRAPHIC PROJECTIONS. Ms. Sicola
ORTHOGRAPHIC PROJECTIONS Ms. Sicola Objectives List the six principal views of projection Sketch the top, front and right-side views of an object with normal, inclined, and oblique surfaces Objectives
More informationChapter 1 Introduction
Chapter 1 Introduction Contents Engineering drawing Drawing standards Drawing sheet Scale Lettering Line types Engineering Drawing Contents Engineering Drawing Effectiveness of Graphic Language 1. Try
More informationAutoCAD 2D I. Module 16. Isometric and Dimensioning. IAT Curriculum Unit PREPARED BY. January 2011
AutoCAD 2D I Module 16 Isometric and Dimensioning PREPARED BY IAT Curriculum Unit January 2011 Institute of Applied Technology, 2011 Module 16 Auto CAD Self-paced Learning Modules AutoCAD 2D Isometric
More informationJUNIOR CERTIFICATE 2009 MARKING SCHEME TECHNICAL GRAPHICS HIGHER LEVEL
. JUNIOR CERTIFICATE 2009 MARKING SCHEME TECHNICAL GRAPHICS HIGHER LEVEL Sections A and B Section A any ten questions from this section Q1 12 Four diagrams, 3 marks for each correct label. Q2 12 2 marks
More informationDownloaded from
Symmetry 1.Can you draw a figure whose mirror image is identical to the figure itself? 2.Find out if the figure is symmetrical or not? 3.Count the number of lines of symmetry in the figure. 4.A line
More informationENGINEERING GRAPHICS UNIT V ISOMETRIC PROJECTION PERSPECTIVE PROJECTION
ENGINEERING GRAPHICS UNIT V ISOMETRIC PROJECTION PERSPECTIVE PROJECTION 1.PICTORIAL PROJECTIONS To visualize the shape of the whole object in its 3- D form, all the two or three orthographic views of the
More informationMultiview Drawing. Definition: Graphical representation of a 3- dimensional object on one plane (sheet of paper) using two or more views.
Multiview Drawing Definition: Graphical representation of a 3- dimensional object on one plane (sheet of paper) using two or more views. Multiview Drawing Another name for multiview drawing is orthographic
More informationI B.TECH- I SEMESTER DEPARTMENT OF MECHANICAL ENGINEERING ENGINEERING DRAWING
I B.TECH- I SEMESTER DEPARTMENT OF MECHANICAL ENGINEERING ENGINEERING DRAWING ENGINEERING DRAWING UNIT-V DEFINITIONS: Axonometric Trimetric Dimetric Isometric It is a parallel technique used to create
More informationDimension Styles. EDT Chapter 18 - Basic Dimensioning Practices 1
Dimension Styles EDT 310 - Chapter 18 - Basic Dimensioning Practices 1 Dimension Styles The appearance of dimensions is controlled by over 70 different settings. Dimension Styles are saved configurations
More informationAssignment 12 CAD Mechanical Part 2
Assignment 12 CAD Mechanical Part 2 Objectives In this assignment you will learn to apply the hidden lines, isometric snap, and ellipses commands along with commands previously learned.. General Hidden
More informationToothbrush Holder. A drawing of the sheet metal part will also be created.
Prerequisite Knowledge Previous knowledge of the following commands is required to complete this lesson; Sketch (Line, Centerline, Circle, Add Relations, Smart Dimension,), Extrude Boss/Base, and Edit
More informationORTHOGRAPHIC PROJECTION
ORTHOGRAPHIC PROJECTION INTRODUCTION Any object has three dimensions, that is, length, width and thickness. A projection is defined as a representation of an object on a two dimensional plane. The projections
More informationDFTG-1305 Technical Drafting Prof. Francis Ha
DFTG-1305 Technical Drafting Prof. Francis Ha Session 4 Orthographic Projection (or Multiview Projection) Reading: Geisecke s textbook: 14 th Ed. Chapter 5 p.162 15 th Ed. Chapter 6 p.232 Update: 18-0205
More informationThis early Greek study was largely concerned with the geometric properties of conics.
4.3. Conics Objectives Recognize the four basic conics: circle, ellipse, parabola, and hyperbola. Recognize, graph, and write equations of parabolas (vertex at origin). Recognize, graph, and write equations
More informationCHAPTER 01 PRESENTATION OF TECHNICAL DRAWING. Prepared by: Sio Sreymean
CHAPTER 01 PRESENTATION OF TECHNICAL DRAWING Prepared by: Sio Sreymean 2015-2016 Why do we need to study this subject? Effectiveness of Graphics Language 1. Try to write a description of this object. 2.
More informationUnit-5 ISOMETRIC PROJECTION
Unit-5 ISOMETRIC PROJECTION Importance Points in Isometric: 1. For drawing the isometric, the object must be viewed such that either the front -right or the left edges becomes nearest. 2. All vertical
More informationENGINEERING GRAPHICS 1E9
Lecture 3 Monday, 15 December 2014 1 ENGINEERING GRAPHICS 1E9 Lecture 3: Isometric Projections Lecture 3 Monday, 15 December 2014 2 What is ISOMETRIC? It is a method of producing pictorial view of an object
More informationTechnical Drawing 101 with AutoCAD 2018
Technical Drawing 101 with AutoCAD 2018 A Multidisciplinary Guide to Drafting Theory and Practice with Video Instruction Douglas Smith Antonio Ramirez Ashleigh Fuller SDC PUBLICATIONS Better Textbooks.
More informationMultiview Projection
DFTG-1305 Technical Drafting Prof. Francis Ha Session 4 Multiview Projection (or Orthographic Projection) Reading: Geisecke s textbook: 14 th Ed. Chapter 5 p.162 15 th Ed. Chapter 6 p.232 Update: 17-0510
More informationEvaluation Chapter by CADArtifex
The premium provider of learning products and solutions www.cadartifex.com EVALUATION CHAPTER 2 Drawing Sketches with SOLIDWORKS In this chapter: Invoking the Part Modeling Environment Invoking the Sketching
More information5.3 Trigonometric Graphs. Copyright Cengage Learning. All rights reserved.
5.3 Trigonometric Graphs Copyright Cengage Learning. All rights reserved. Objectives Graphs of Sine and Cosine Graphs of Transformations of Sine and Cosine Using Graphing Devices to Graph Trigonometric
More informationCATIA Instructor-led Live Online Training Program
Course Outline Introduction & Understanding to CATIA Environment Introduction & Understanding to CATIA interface Starting new file Understand the Sketcher workbench of CATIA V5 Start a new file in the
More informationIntroduction to Autodesk Inventor User Interface Student Manual MODEL WINDOW
Emmett Wemp EDTECH 503 Introduction to Autodesk Inventor User Interface Fill in the blanks of the different tools available in the user interface of Autodesk Inventor as your instructor discusses them.
More informationJUNIOR CERTIFICATE 2008 MARKING SCHEME TECHNICAL GRAPHICS HIGHER LEVEL
JUNIOR CERTIFICATE 2008 MARKING SCHEME TECHNICAL GRAPHICS HIGHER LEVEL Sections A and B Section A - any ten questions from this Section Q1 12 Four diagrams, 3 marks for each correct label. Q2 12 3 height
More informationCLASS views from detail on a grid paper. (use appropriate line types to show features) - Optional views. Turn in for grading on class 6 (06/04)
CLASS 4 Review: - Projections - Orthographic projections Lab: - 3 views from detail on a grid paper. (use appropriate line types to show features) - Optional views. Turn in for grading on class 6 (06/04)
More informationResidential Design Using AutoCAD 2018
Daniel John Stine CSI, CDT Residential Design Using AutoCAD 2018 Includes video instruction SDC P U B L I C AT I O N S Better Textbooks. Lower Prices. www.sdcpublications.com ACCESS CODE UNIQUE CODE INSIDE
More informationDownloaded from
Symmetry 1 1.A line segment is Symmetrical about its ---------- bisector (A) Perpendicular (B) Parallel (C) Line (D) Axis 2.How many lines of symmetry does a reactangle have? (A) Four (B) Three (C)
More informationDrawing a Plan of a Paper Airplane. Open a Plan of a Paper Airplane
Inventor 2014 Paper Airplane Drawing a Plan of a Paper Airplane In this activity, you ll create a 2D layout of a paper airplane. Please follow these directions carefully. When you have a question, reread
More information1 ISOMETRIC PROJECTION SECTION I: INTRODUCTION TO ISOMETRIC PROJECTION
1 ISOMETRIC PROJECTION SECTION I: INTRODUCTION TO ISOMETRIC PROJECTION Orthographic projection shows drawings of an object in a two-dimensional format, with views given in plan, elevation and end elevation
More informationChapter 6. Architectural Lines and Lettering
Chapter 6 Architectural Lines and Lettering Drafting Introduction Universal graphic language Uses lines, symbols, dimensions, and notes to describe a structure to be built Properly drawn lines are dark,
More informationChapter 5 Pictorial Projection
Chapter 5 Pictorial Projection Objectives After completing this chapter, the students will be able to Create freehand sketches using the correct sketching techniques. Explainthe difference between axonometric
More informationENGINEERING DRAWING SKKK 1021 ISOMETRIC DRAWING. Agus Arsad, Azizul Azri Bin Mustaffa 10/2/2012 1
ENGINEERING DRAWING SKKK 1021 ISOMETRIC DRAWING Agus Arsad, Azizul Azri Bin Mustaffa 10/2/2012 1 LEARNING OUTCOMES ISOMETRIC DRAWING It is expected that students will be able to: Understand the significance
More informationFundamentals for building Drawing
Fundamentals for building Drawing What is Drawing Introduction Knowledge of preparing and understanding drawing will prove to be an invaluable aid while performing their jobs effectively, efficiently.
More informationBeginner s Guide to SolidWorks Alejandro Reyes, MSME Certified SolidWorks Professional and Instructor SDC PUBLICATIONS
Beginner s Guide to SolidWorks 2008 Alejandro Reyes, MSME Certified SolidWorks Professional and Instructor SDC PUBLICATIONS Schroff Development Corporation www.schroff.com www.schroff-europe.com Part Modeling
More informationElements of Art: Space
Creating Depth with Size 1) In the top third of your page, draw a horizon line (line across the page for your horizon) and objects in the background that will suit your own art piece. Draw lightly in pencil.
More information4.4 Slope and Graphs of Linear Equations. Copyright Cengage Learning. All rights reserved.
4.4 Slope and Graphs of Linear Equations Copyright Cengage Learning. All rights reserved. 1 What You Will Learn Determine the slope of a line through two points Write linear equations in slope-intercept
More informationQuick Start for Autodesk Inventor
Quick Start for Autodesk Inventor Autodesk Inventor Professional is a 3D mechanical design tool with powerful solid modeling capabilities and an intuitive interface. In this lesson, you use a typical workflow
More informationDrawing Standards & Conventions for IDD
Drawing Standards & Conventions for IDD This document consists of a set of standards that have been developed to maintain a consistency in Interior Decoration and Design students work. The standards are
More informationClock Exercise (Inserting Planes)
Clock Exercise (Inserting Planes) Prerequisite Knowledge To complete this exercise you will need to be familiar with Sketching, Applying relations, Extrude Boss/ Base, Extrude cut, Applying Textures, Renaming
More informationSolid Part Four A Bracket Made by Mirroring
C h a p t e r 5 Solid Part Four A Bracket Made by Mirroring This chapter will cover the following to World Class standards: Sketch of a Solid Problem Draw a Series of Lines Finish the 2D Sketch Extrude
More informationDrawing sheet: - The various size of the drawing sheet used for engineering drawing as per IS Are listed in the table
Dronacharya Group of Institutions, Greater Noida Computer Aided Engineering Graphics (CAEG) (NCE 151/251) List of Drawing Sheets: 1. Letter writing & Dimensioning. 2. Projection of Points & Lines. 3. Projection
More informationTutorial 2: Setting up the Drawing Environment
Drawing size With AutoCAD all drawings are done to FULL SCALE. The drawing limits will depend on the size of the items being drawn. For example if our drawing is the plan of a floor 23.8m X 15m then we
More informationModule 1E: Parallel-Line Flat Pattern Development of Sheet- Metal Folded Model Wrapping the 3D Space of An Oblique Circular Cylinder
Inventor (10) Module 1E: 1E- 1 Module 1E: Parallel-Line Flat Pattern Development of Sheet- Metal Folded Model Wrapping the 3D Space of An Oblique Circular Cylinder In this Module, we will explore the topic
More informationShaft Hanger - SolidWorks
ME-430 INTRODUCTION TO COMPUTER AIDED DESIGN Shaft Hanger - SolidWorks BY: DR. HERLI SURJANHATA ASSIGNMENT Submit TWO isometric views of the Shaft Hanger with your report, 1. Shaded view of the trimetric
More informationAdvance Steel. Tutorial
Advance Steel Tutorial Table of contents About this tutorial... 7 How to use this guide...9 Lesson 1: Creating a building grid...10 Step 1: Creating an axis group in the X direction...10 Step 2: Creating
More informationAnchor Block Draft Tutorial
Anchor Block Draft Tutorial In the following tutorial you will create a drawing of the anchor block shown. The tutorial covers such topics as creating: Orthographic views Section views Auxiliary views
More informationPASS Sample Size Software
Chapter 945 Introduction This section describes the options that are available for the appearance of a histogram. A set of all these options can be stored as a template file which can be retrieved later.
More informationACAD-BAU TUTORIAL For BricsCAD platform
ACAD-BAU TUTORIAL WWW.ARHINOVA.SI For BricsCAD platform August 06 WORKSPACE ACAD-BAU RIBBON ACAD-BAU CONTROL BAR F ACAD-BAU PALETTES BASIC SETTINGS Use New command and open the template called ACB_International.DWT.
More informationChapter 9. Conic Sections and Analytic Geometry. 9.1 The Ellipse. Copyright 2014, 2010, 2007 Pearson Education, Inc.
Chapter 9 Conic Sections and Analytic Geometry 9.1 The Ellipse Copyright 2014, 2010, 2007 Pearson Education, Inc. 1 Objectives: Graph ellipses centered at the origin. Write equations of ellipses in standard
More information(As per New Revised Syllabus of Anna University) Department of Mechanical Engineering. SATHYABAMA UNIVERSITY Jeppiaar Nagar, Chennai
(1*,1((5,1* *5$3+,&6 (As per New Revised Syllabus of Anna University) Dr. S.RAMACHANDRAN, M.E., Ph.D. Professor & Head K. PANDIAN, M.E., E.V.V.RAMANAMURTHY, M.Tech., R. DEVARAJ, M.E., Associate Professors
More informationCreate Fractions in Google Sketch up
Page1 Create Fractions in Google Sketch up Open the Plan View- Feet and Inches template from the start up screen. If you are already in sketch up you can switch to this view: Window>Preferences>Template
More informationIntroduction to CATIA V5
Introduction to CATIA V5 Release 17 (A Hands-On Tutorial Approach) Kirstie Plantenberg University of Detroit Mercy SDC PUBLICATIONS Schroff Development Corporation www.schroff.com Better Textbooks. Lower
More informationENGINEERING DRAWING. 1. Set squares are used to draw different angles. What is the angel a formed by the 45⁰ set square? Give a brief answer.
ENGINEERING DRAWING 1. Set squares are used to draw different angles. What is the angel a formed by the 45⁰ set square? Give a brief answer. 2. Which is the correct method of hatching a plane surface?
More informationISOMETRIC PROJECTION. Contents. Isometric Scale. Construction of Isometric Scale. Methods to draw isometric projections/isometric views
ISOMETRIC PROJECTION Contents Introduction Principle of Isometric Projection Isometric Scale Construction of Isometric Scale Isometric View (Isometric Drawings) Methods to draw isometric projections/isometric
More informationStarting a 3D Modeling Part File
1 How to Create a 3D Model and Corresponding 2D Drawing with Dimensions, GDT (Geometric Dimensioning and Tolerance) Symbols and Title Block in SolidWorks 2013-2014 By Edward Locke This tutorial will introduce
More informationIsometric Drawings. Figure A 1
A Isometric Drawings ISOMETRIC BASICS Isometric drawings are a means of drawing an object in picture form for better clarifying the object s appearance. These types of drawings resemble a picture of an
More informationEngineering Graphics Essentials with AutoCAD 2015 Instruction
Kirstie Plantenberg Engineering Graphics Essentials with AutoCAD 2015 Instruction Text and Video Instruction Multimedia Disc SDC P U B L I C AT I O N S Better Textbooks. Lower Prices. www.sdcpublications.com
More informationBrief Introduction to Engineering Graphics The use of drawings to convey information. Sketching freehand straight edge
Brief Introduction to Engineering Graphics The use of drawings to convey information. Sketching freehand straight edge CAD drawings 2D drafting 3D model to 2D drawings 1 Different Graphical Representation
More informationSectional Views. DFTG-1305 Technical Drafting by Prof. Francis Ha. Session 6. Geisecke s textbook: 14 th Ed. Chapter 7 p th Ed. Chapter 8 p.
DFTG-1305 Technical Drafting by Prof. Francis Ha Session 6 Sectional Views Geisecke s textbook: 14 th Ed. Chapter 7 p.242 15 th Ed. Chapter 8 p.326 Update: 18-10007 What is this? An ugly rock? Sectional
More informationHydro Hull. Chapter 21. Boat. A. Save as "HYDRO". Step 1. Open your HULL MID PLANE file (Chapter 2).
Chapter 21 Boat Hydro Hull A. Save as "HYDRO". Step 1. Open your HULL MID PLANE file (Chapter 2). Step 2. Click File Menu > Save As. Step 3. Key-in HYDRO for the filename and press ENTER. B. Delete Loft1,
More informationDELHI TECHNOLOGICAL UNIVERSITY ENGINEERING GRAPHICS LAB MANUAL
DELHI TECHNOLOGICAL UNIVERSITY ENGINEERING GRAPHICS LAB MANUAL NAME: - ROLL NO: - GROUP: - BRANCH: - GROUP TEACHER: Page 1 www.rooplalrana.com 1 GENERAL INSTRUCTIONS FOR ENGG. GRAPHICS LAB 1) Students
More informationCAD and Drafting Standards Working Drawings
CAD and Drafting Standards Working Drawings Gregory Mocko Introduction 2 The purpose of drawing or generating a CAD document is to communicate Essentially, since communication is the goal, some standards
More informationtechnical drawing school of art, design and architecture nust spring 2011
technical drawing school of art, design and architecture nust spring 2011 http://www.youtube.com/watch?v=e55ocgb0l8o t e c h n i c a l d r a w i n g a mean to design reasoning spring 2011 the ability to
More informationID 40 Residential Design. General Notes Title Sheet and Index Cross-reference Symbols
ID 40 Residential Design General Notes Title Sheet and Index Cross-reference Symbols Title Sheet All plan sets include a Title sheet. It usually features a site plan, a drawing index, and the name of the
More informationSolidWorks 95 User s Guide
SolidWorks 95 User s Guide Disclaimer: The following User Guide was extracted from SolidWorks 95 Help files and was not originally distributed in this format. All content 1995, SolidWorks Corporation Contents
More informationENGINEERING GRAPHICS ESSENTIALS
ENGINEERING GRAPHICS ESSENTIALS with AutoCAD 2012 Instruction Introduction to AutoCAD Engineering Graphics Principles Hand Sketching Text and Independent Learning CD Independent Learning CD: A Comprehensive
More informationENGINEERING DRAWING IM 09 AND GRAPHICAL COMMUNICATION
IM SYLLABUS (2014) ENGINEERING DRAWING IM 09 AND GRAPHICAL COMMUNICATION SYLLABUS Engineering Drawing and Graphical Communication IM 09 (Available in September) Syllabus 1 Paper (3 hours) Aims The aims
More informationAPJ ABDUL KALAM TECHNOLOGICAL UNIVERSITY SECOND SEMESTER B.TECH DEGREE EXAMINATION, MAY PART A Answer ANY Two questions. 10 marks each.
B B2B111 Pages: 2 Reg. No. Name: SECOND SEMESTER B.TECH DEGREE EXAMINATION, MAY 2017 Max.Marks:50 Course Code: BE110 Duration:3Hours Answer ANY Two questions. 10 marks each. 1. A line AB 100 mm long and
More informationENGINEERING GRAPHICS 1.0 Introduction Engineering Graphics Drawing as an art Artist Graphic design Engineering graphics engineering drawing
ENGINEERING GRAPHICS 1.0 Introduction Engineering is the profession in which the knowledge of mathematics and science gained by study, experience and practice is applied with good judgment to develop a
More informationGetting started with. Getting started with VELOCITY SERIES.
Getting started with Getting started with SOLID EDGE EDGE ST4 ST4 VELOCITY SERIES www.siemens.com/velocity 1 Getting started with Solid Edge Publication Number MU29000-ENG-1040 Proprietary and Restricted
More information< Then click on this icon on the vertical tool bar that pops up on the left side.
Pipe Cavity Tutorial Introduction The CADMAX Solid Master Tutorial is a great way to learn about the benefits of feature-based parametric solid modeling with CADMAX. We have assembled several typical parts
More informationMechanical Drawing. Unit 2 Study Guide for Chapters 6-10
Mechanical Drawing Unit 2 Study Guide for Chapters 6-10 Chapter 6 Multiview Drawing Section 6.1 Understanding Orthographic Projection A. Technical Drawing: How can a technical drawing give more accurate
More informationFUSION 360: SKETCHING FOR MAKERS
FUSION 360: SKETCHING FOR MAKERS LaDeana Dockery 2017 MAKEICT Wichita, KS 1 Table of Contents Interface... 1 File Operations... 1 Opening Existing Models... 1 Mouse Navigation... 1 Preferences... 2 Navigation
More informationSAMPLE QUESTION PAPER III ENGINEERING GRAPHICS (046) Time Allowed: 3 hours Maximum Marks: 70
SAMPLE QUESTION PAPER III ENGINEERING GRAPHICS (046) Time Allowed: 3 hours Maximum Marks: 70 Note: (i) Attempt all the questions. (ii) Use both sides of the drawing sheet, if necessary. (iii) All dimensions
More informationA General Procedure (Solids of Revolution) Some Useful Area Formulas
Goal: Given a solid described by rotating an area, compute its volume. A General Procedure (Solids of Revolution) (i) Draw a graph of the relevant functions/regions in the plane. Draw a vertical line and
More informationConstructing a Wedge Die
1-(800) 877-2745 www.ashlar-vellum.com Using Graphite TM Copyright 2008 Ashlar Incorporated. All rights reserved. C6CAWD0809. Ashlar-Vellum Graphite This exercise introduces the third dimension. Discover
More information