Rebecca Media Console-Side Hutch [1]

Transcription

1 [1] Submitted by Ana White [2] on Thu, :35 Page 1 of 18

2 Page 2 of 18

3 [1] Additional Photos [3] [4] [5] [6] [7] HAPPY FRIDAY!!! Page 3 of 18

4 This week, I'm attending the most awesome craft blogging conference, SNAP! [8] I thank everyone helping others out this week in comments and on our Facebook page in this week of travel or me. You are too kind. And this week, a HUGE thank you to Rebecca for working with me to share new media wall plans! Don't you just love this media suite? From Rebecca: These hutch additions totally make the media suite. The side pieces are more narrow than the whole unit, only about 8 inches. It is perfect for those narrower books, DVD's and lots of fun display space. The plan is designed with a drawer on the bottom of the shelf. I personally decided not to do drawers, #1 because it required more wood than we had, and #2 because being this narrow, you really would only put remotes or small objects inside. But that is totally up to you! Make sure you stop over and visit Rebecca at her blog for lots more tips and photos. [9] Thanks Rebecca! Summary: Build a media wall! Free plans for side hutch! CategoriesProject Type: Bookshelf and Bookcase Plans [10] Buffet, Sideboard and Credenza Plans [11] Hutch Plans [12] Media and Entertainment Centers [13] Room: storage and organization [14] dining room [15] living room [16] Page 4 of 18

5 Skill Level: Advanced [17] Style: Cottage Style Furniture Plans [18] Dimensions: Dimensions are shown above Dimensions: sheet 3/4" Plywood sheet 1/4" Plywood 8ft 1x2's 8ft 1x4 (or 54") Common Materials: 3/4 inch finish nails 1-1/4" Pocket Hole Screws [19] Elmer's Wood Glue [20] Elmer's Wood Filler [21] 120 grit sandpaper primer paint paint brush Page 5 of 18

6 Tools: Page 6 of 18

7 [22] [23] [24] [25] [26] [27] Cut List: 3/4" Plywood 7 3/4" x 27 1/4" Page 7 of 18

8 7 3/4" x 24" 7 3/4" x 43 1/4" 1/4" Plywood 25 1/2" x 35 3/4" 1x2's 7 3/4" 22 1/2" 39 3/4" 27 1/4" 1x4's 25 1/2" Molding for top 27 1/4" (cut on miter, take measurements!) 9 1/4" (cut on miter, take measurements!) Cutting Instructions: This is a shopping and cut list to build TWO of these. Please refer to the 3D version of the cut list (step 8 and 9) to see what you will need! General Instructions: Please read through the entire plan and all comments before beginning this project. It is also advisable to review the Getting Started Section. Take all necessary precautions to build safely and smartly. Work on a clean level surface, free of imperfections or debris. Always use straight boards. Check for square after each step. Always predrill holes before attaching with screws. Use glue with finish nails for a stronger hold. Wipe excess glue off bare wood for stained projects, as dried glue will not take stain. Be safe, have fun, and ask for help if you need it. Good luck! Step 1 Page 8 of 18

9 [28] Start by building the box. You can use either 11/4 ph screws or 2" countersunk screws and glue. Step 2 Page 9 of 18

10 [29] These are for support and also act as drawer guides if you use drawers. Step 3 Page 10 of 18

11 [30] Build the face frame first if you have a pocket hole jig. Otherwise attach with 2" finish nails and glue. Note to attach face frame to side overhangs are in opposite so you end up with a left and right hutch. Step 4 Page 11 of 18

12 [31] Now add the top. Easy step. :) Step 5 Page 12 of 18

13 [32] And the back. If you loose the drawer, bring plywood all the way down the back. Step 6 Page 13 of 18

14 [33] Now crown... Cut to fit, mirroring corners. Step 7 Page 14 of 18

15 [34] And the drawer... Step 8 Page 15 of 18

16 [35] Bless Rebecca for putting together these layouts. She is too kind and helpful. Step 9 [36] Finishing InstructionsPreparation Instructions: Fill all holes with wood filler and let dry. Apply additional coats of wood filler as needed. When wood filler is completely dry, sand the project in the direction of the wood grain with 120 grit sandpaper. Vacuum sanded project to remove sanding residue. Remove all sanding residue on work surfaces as well. Wipe project clean with damp cloth. It is always recommended Page 16 of 18

17 to apply a test coat on a hidden area or scrap piece to ensure color evenness and adhesion. Use primer or wood conditioner as needed. Source URL: -console-side-hutch Links [1] e-hutch [2] [3] 38.jpg [4] 38.jpg [5] 38.jpg [6] 38.jpg [7] 38.jpg [8] [9] [10] [11] [12] [13] [14] zation [15] [16] [17] [18] [19] TF8&camp=1789&creative=390957&creativeASIN=B U2&linkCode=as2&tag=knooffwoo-20&linkId=5AJJ GUAWGYX2TT7E [20] [21] struction# Page 17 of 18

18 [22] [23] [24] [25] [26] [27] [28] jpg [29] jpg [30] jpg [31] jpg [32] jpg [33] jpg [34] jpg [35] jpg [36] jpg Page 18 of 18