Shoe Shrine Shelves [1]

Transcription

1 Shoe Shrine Shelves [1] Submitted by Ana White [2] on Fri, :40 [1] Thank you to our readers for requesting! The main thing on this one, build square, use square boards, take your time and measure out every single joint. We don't have the room in our small home for such a marvelous piece, but I can't wait to see the Shoe Shrine Tower in yours! One thing to consider, you can alternate placing the larger "boot" cubbies to the top instead of the bottom if you prefer that look. Page 1 of 19

2 Have a great weekend, Happy Building! Summary: Free, simple, easy, DIY, step by step plans to build the ultimate shoe storage cabinet. Inspired by Ballard Design's Sarah Storage Tower, [3] you can think beyond the boots and shoes and handbags - this beautiful storage cabinet would work anywhere from the Nursery to the office, the entryway to the dining room. CategoriesProject Type: Bookshelf and Bookcase Plans [4] Cubby Project Plans [5] Room: storage and organization [6] Bedroom [7] Closets [8] entry way [9] Kids and Toys [10] Nursery and Baby [11] office [12] Skill Level: Intermediate [13] Style: Cottage Style Furniture Plans [14] Modern Style Furniture Plans [15] Children's and Kid's Room Furniture and Toy Plans [16] Estimated Cost: $100-$150 [17] Dimensions: Dimensions are shown above. Dimensions: Page 2 of 19

3 8 feet long 4 feet long 1 - sheet 1/4" plywood Page 3 of 19

4 Common Materials: 1 1/4 inch finish nails 2 inch finish nails 1-1/4" Pocket Hole Screws [18] Elmer's Wood Glue [19] Elmer's Wood Filler [20] 120 grit sandpaper primer wood conditioner paint paint brush Tools: Page 4 of 19

5 [21] [22] [23] [24] [25] [26] Page 5 of 19

6 Cut List: 25 1/2" (Shelves) 84 1/2" (Sides) 8" (Small Dividers) 25" (Large Dividers) 25 1/2" (Footer) 8" (Optional Shelves, Boot Cubbies - see last step) 1-1/4" 27" x 84 1/2" (Back) General Instructions: Please read through the entire plan and all comments before beginning this project. It is also advisable to review the Getting Started Section. Take all necessary precautions to build safely and smartly. Work on a clean level surface, free of imperfections or debris. Always use straight boards. Check for square after each step. Always predrill holes before attaching with screws. Use glue with finish nails for a stronger hold. Wipe excess glue off bare wood for stained projects, as dried glue will not take stain. Be safe, have fun, and ask for help if you need it. Good luck! Step 1 Page 6 of 19

7 [27] The trickiest part about building this shoe storage cabinet is going to be getting the joints done when there is limited clearance. You will need a Kreg Jig [21] to join some of your shelves. Start by drilling pocket holes as shown in diagrams along the top edge of your dividers. Then attach two short dividers to the top shelf as shown above. Step 2 Page 7 of 19

8 [28] Now you won't be able to get a regular drill in there to do pocket holes along the bottom edge of the dividers. Apply glue, mark joints, and attach with either 2" finish nails or screws from the underside as shown above. Step 3 Page 8 of 19

9 [29] Now you can add another row of dividers, this time you will have to use the pocket holes. A word to the wise, don't eyeball the location of your dividers - measure and mark 8" from the outsides and place, if you eyeball, over the course of several rows of shelves, you might just start to notice you are getting "off". Step 4 Page 9 of 19

10 [30] Continue alternating adding dividers and shelves until you are out of the short dividers. Step 5 Page 10 of 19

11 [31] Then add the long dividers as shown in the diagram above. Step 6 Page 11 of 19

12 [32] And finally the bottom. Step 7 Page 12 of 19

13 [33] Page 13 of 19

14 Measure and mark your sides as shown above, marking the location of each shelf. Measurements shown are to the tops fo the shelves. Line sides up with shelves and attach, using 2" finish nails and glue. Step 8 [34] Attach footer as shown above, with 2" finish nails and wood glue. Use the measurements above to help you draw a pattern. Cut pattern out carefully with a jigsaw. Step 9 Page 14 of 19

15 [35] Step 9 Instructions: Adjust cabinet for square and attach back with 1 1/4" finish nails and wood glue. Page 15 of 19

16 Step 10 Page 16 of 19

17 [36] These shelves as done by Ballard Designs on their Sarah Storage Tower are adjustable. Use shelf pins to place shelves. Page 17 of 19

18 Finishing InstructionsPreparation Instructions: Fill all holes with wood filler and let dry. Apply additional coats of wood filler as needed. When wood filler is completely dry, sand the project in the direction of the wood grain with 120 grit sandpaper. Vacuum sanded project to remove sanding residue. Remove all sanding residue on work surfaces as well. Wipe project clean with damp cloth. It is always recommended to apply a test coat on a hidden area or scrap piece to ensure color evenness and adhesion. Use primer or wood conditioner as needed. Source URL: Links [1] [2] [3] b-boot/furniture/cabinets/ [4] [5] [6] ation [7] [8] [9] [10] [11] [12] [13] [14] [15] [16] [17] [18] TF8&camp=1789&creative=390957&creativeASIN=B U2&linkCode=as2&tag=knooffwoo-20&linkId=5AJJ GUAWGYX2TT7E [19] [20] struction# Page 18 of 19

19 [21] [22] [23] [24] [25] [26] [27] rganization%20closet%20design%20plans%203.png [28] rganization%20closet%20design%20plans%204.png [29] rganization%20closet%20design%20plans%205.png [30] rganization%20closet%20design%20plans%206.png [31] rganization%20closet%20design%20plans%207.png [32] rganization%20closet%20design%20plans%208.png [33] rganization%20closet%20design%20plans%209.png [34] rganization%20closet%20design%20plans%2010.png [35] rganization%20closet%20design%20plans%2011.png [36] rganization%20closet%20design%20plans%2012.png Page 19 of 19