Folding Lap Desk [1] Additional Photos. Folding Lap Desk Published on Ana White (

Transcription

1 [1] Submitted by Ana White [2] on Fri, :26 [1] Additional Photos [3] [4] Page 1 of 17

2 [5] [6] [7] Hi everyone! Don't you love hand making Christmas and Holiday gifts for your loved ones? It's just so special to handmake gifts, and can often be so much more affordable than buying. That - and you can customize the gifts too! So every gift you give can be unique and personal. This year, to help you have a Handmade Holiday, I'm teaming up with my friend Jaime from That's My Letter [8]to bring you a new gift plan each week! Page 2 of 17

3 It's going to be like Christmas every Friday!!! We are trying to keep the cost of materials as low as possible and the projects simple, so we can all pile the gifts up under the tree. Many of the projects will use scrap lumber. So stay tuned and check back every week for new project plans! Page 3 of 17

4 I can't tell you how excited I am about the first project in this series! It's a little lap desk, Page 4 of 17

5 Perfect for creativity, playing school, family movie night, or tea parties in bed. Page 5 of 17

6 And then when not in use, the little desk neatly folds flat to be put away. How about using a handle as a hook, and hanging on the wall? You could even use a chalkboard for the top, so when not in use, it doubles as a wall chalkboard! Know anyone on your list that might love this? Well, of course, we got you covered with the free, step by step plans following! But please take a second first to check out Jaime's building post here, [8]she's got lots of tips and step by step pictures! Thank you Jaime! And don't forget to check back next week for another inexpensive Page 6 of 17

7 building project perfect for your Handmade Holiday! Happy Building! Ana Summary: DIY plans for a folding lap desk from Ana-White.com CategoriesProject Type: Desk, Desk Systems and Project Table Plans [9] Side and End Table Plans [10] Kids Tables and Chairs [11] Toys [12] main_category: Handmade Holidays [13] Room: Teens [14] Bedroom [15] Kids and Toys [16] living room [17] Nursery and Baby [18] Skill Level: Beginner [19] Style: Children's and Kid's Room Furniture and Toy Plans [20] Estimated Cost: Under $20 [21] Dimensions: Dimensions shown above Dimensions: Page 7 of 17

8 10 feet of 1x2s Plywood for top 4 bolts, 2 1/2 length, with washers and nuts You may also need a catch or hook/eye closure to keep legs folded closed for transporting Handle if desired Tools: Page 8 of 17

9 [22] Cut List: /2 8 1/4 (top end is cut to point 45 degrees angle and bottom cut at 15 degree angle - see in plans) Top is 13 1/2 x 21 General Instructions: Please read through the entire plan and all comments before beginning this project. It is also advisable to review the Getting Started Section. Take all necessary precautions to build safely and smartly. Work on a clean level surface, free of imperfections or debris. Always use straight boards. Check for square after each step. Always predrill holes before attaching with screws. Use glue with finish nails for a stronger hold. Page 9 of 17

10 Wipe excess glue off bare wood for stained projects, as dried glue will not take stain. Be safe, have fun, and ask for help if you need it. Good luck! Step 1 [23] First, mark the location of your bolt holes on the 1x2s that are 21" long. Drill the holes sized for your bolts. Take the 1x2 frame boards, and build your frame. The frame can be nailed and glued, screwed, pocket holed - it's your choice. The top plywood piece will really help hold everything together. Step 2 Page 10 of 17

11 [24] Next, build your two leg sets and drill matching holes for bolts in the tops of the legs. NOTE: Jaime recommends mitering the bottom corner at 15 degrees too to help the table stand better when open - Page 11 of 17

12 And also act as a finger pull for opening the table. Page 12 of 17

13 Step 3 Page 13 of 17

14 [25] Then use the bolts to attach the legs to the frame. Step 4 Page 14 of 17

15 [26] Glue and nail smooth plywood or other material to the top. Add a handle and personalize as desired! PS - Don't forget the pretty bow! Finishing InstructionsPreparation Instructions: Fill all holes with wood filler and let dry. Apply additional coats of wood filler as needed. When wood filler is completely dry, sand the project in the direction of the wood grain with 120 grit sandpaper. Vacuum sanded project to remove sanding residue. Remove all sanding residue on work surfaces as well. Wipe project clean with damp cloth. It is always recommended to apply a test coat on a hidden area or scrap piece to ensure color evenness and adhesion. Use primer or wood conditioner as needed. Page 15 of 17

16 Source URL: Links [1] [2] [3] 79.jpg [4] 79.jpg [5] 79.jpg [6] 79.jpg [7] 79.jpg [8] [9] [10] [11] [12] [13] -holidays [14] [15] [16] [17] [18] [19] [20] [21] [22] [23] jpg [24] jpg [25] jpg [26] Page 16 of 17

17 179.jpg Page 17 of 17