Notes B

Transcription

1

2 Notes B 2

3 TABLE OF CONTENTS TEKS Fastener Features...B 4 TEKS Self Drilling Fasteners...B 5 Light Duty Steel-To-Steel Applications...B 6 Medium Duty Steel-To-Steel Applications...B 8 Heavy Duty Steel-To-Steel Applications...B 11 Low Profile Architectural Metal Roof Clip Fasteners...B 14 Wood-to-Metal Fasteners...B 16 TEKS with Bonded Washer...B 19 Dekstrip Expandable Edged Flashing...B 22 Dektite and Retrofit Dektite...B 25 TAPCON Concrete and Masonry Anchors...B 28 TAPCON Ceiling Anchor...B 32 E-Z Drywall Anchors...B 34 Rock-On and Backer-On Fasteners...B 36 Gridmate BR Plastic Insulation Fasteners...B 38 B 3

4 TEKS Fastening Features FEATURES Head Threads Pilot Section (When Necessary) Flute Point HEAD Proper head style choice will ensure stability during driving, proper clamping and desired finished appearance. THREAD FORM AND DIAMETER The correct choice of thread form and diameter optimizes low installation torque with high pullout strength. PILOT SECTION The unthreaded portion of the point assures the drilling of the steel is completed before the threads begin tapping into the drilled hole. POINT The point is designed to efficiently remove material and precisely size the hole for the thread. FINISH Platings and coatings provide lubricity during drilling and tapping as well as corrosion resistance. FASTENER DESCRIPTION AND BREAKDOWN EXAMPLE x 3/4" HWH Teks/3 Nominal Screw Size Threads Per Inch Screw Length Head Style Drill Point Type Nominal Screw Sizes Thread Decimal Diameter Equivalent #6.140 #7.150 #8.160 #9.180 # # # # # /4.250 # Steel Gauge Chart Common Decimal Eq. Sheet Steel Gauges Inches MM / / / / Material Thickness (Inches) Screw Size Point 2.4mm mm 2.4mm mm 2.4mm mm 2.50mm mm Drill and Tap Material Thickness Chart 5.3mm mm 4.17mm mm 5.3mm mm 5.3mm mm 6.36mm mm 6.36mm mm 9.51mm mm 12.72mm mm 12.72mm mm #10 #12 1/4 #8 #12 #10 #12 1/4 #12 1/4 #12 #12 1/4 Teks/1 Teks/2 Teks/3 Teks/4 Teks/4.5 Teks/5 *Drill & tap capacities may vary with special feature designs. Refer to product reports for specifics. B 4

5 TEKS Self-Drilling Fasteners Preferred Most by Electrical, Decking, HVAC and Metal Building Contractors DESCRIPTION/ADVANTAGES Light Duty Steel-To-Steel Applications SPECIFICATIONS Diameter / 8-18 Thread Form Head Styles TEKS Self-Drilling Fasteners Sharp convex drill point has precise cutting edges to improve drill performance with less effort. Non-walking point provides fast material engagement. Unique point to thread design extrudes the metal preventing stripout. Point to thread design maximizes pullout performance and minimizes backout. Three head styles available to handle various applications. Climaseal finish provides excellent corrosion resistance Hex Washer Head Socket Pan Head Modified Truss Head (HWH) (SP) (MTH) Drill Point Teks 2 Teks 3 Finish Type Kesternich Results Salt Spray Results (DIN 50018, 2.OL) (ASTM B117) Electro-zinc (EZ) 3 cycles - 5% or less red rust 48 hours - 5% or less red rust Climaseal Coating (CL) 30 cycles - 10% or less red rust 1000 hours - 10% or less red rust Climaseal + Coating (CL+) Meets or exceeds Kesternich and Salt Spray Results of Climaseal Coating (CL) INSTALLATION INSTRUCTIONS 1. A standard screwgun with a depth sensitive nosepiece should be used to install Teks. For optimal fastener performance, the screwgun should be a minimum of 4 amps and have a RPM range of Adjust the screwgun nosepiece to properly seat the fastener. 3. New magnetic sockets must be correctly set before use. Remove chip build-up as needed. 4. The fastener is fully seated when the head is flush with the work surface. 5. Overdriving may result in torsional failure of the fastener or stripout of the substrate. 6. The fastener must penetrate beyond the metal structure a minimum of 3 pitches of thread. B 5

6 TEKS Light Duty Steel-To-Steel Applications Stitch roof deck and wall panel sidelaps. HVAC, electrical trim accessories to steel framing. Residential steel frame construction. Brick ties to steel framing. Track to stud and stud splicing. Hat channel to stud. APPROVALS/LISTINGS Factory Mutual (J.I. 2 X 9A2 AM) ICC - ESR 1976 SELECTION CHART TEKS Fasteners PART REFERENCE DESCRIPTION Finish: Electro-Zinc Plating. HEAD STYLE DRILL POINT DRILL & TAP CAPACITY MAX. MATERIAL ATTACHMENTS BOX QTY P/A X PAK QTY PAK QTY 2240 X 2240 X 8-18 x 1/2" #2 SP # ,000 1, x 1/2" MTH # , X 2280 X 8-18 x 5/8" #2 SP # ,000 1, X 2330 X 8-18 x 3/4" #2 SP # ,000 1, X 2360 X A 8-18 x 1" #2 SP # , X 2220 P X 8-18 x 1/2" 1/4" HWH # ,000 1, X 2310 X A 8-18 x 3/4" 1/4" HWH # ,000 1, A 8-18 x 1" 1/4" HWH # ,000 P Available in P/A PAK TEKS Fasteners PART REFERENCE X Available in X PAK DESCRIPTION Finish: Electro-Zinc Plating. HEAD STYLE DRILL POINT DRILL & TAP CAPACITY MAX. MATERIAL ATTACHMENTS BOX QTY P/A X PAK QTY PAK QTY - HVAC, electrical trim accessories to steel framing - Residential steel frame construction - Track to stud - Hat channel to stud - Stud splicing 2480 X 2480 X x 3/4" #2 SP # , Clips, duct straps, brick 2490 X 2490 X x 1" #2 SP # , ties or accessories to steel framing 2495 X 2495 X x 1-1/4" #2 SP # , X 2400 X x 1/2" 5/16" HWH # ,000 1, P X 2460 P X x 3/4" 5/16" HWH # , A X 2510 A X x 1" 5/16" HWH # , P Available in P/A PAK X Available in X PAK TEKS Fasteners PART REFERENCE DESCRIPTION Finish: Climaseal Coating. HEAD STYLE DRILL POINT DRILL & TAP CAPACITY MAX. MATERIAL ATTACHMENTS BOX QTY x 3/4" 5/16" HWH # ,000 - Clips, duct straps, brick ties or x 1-1/2" 5/16" HWH # ,000 accessories to steel framing 2220CL 2220CL 8-18 X 1/2" 1/4" HWH # ,000 + (CL+) Coating B 6

7 PERFORMANCE TABLES Sheet Steel Gauges TEKS Light Duty Steel-To-Steel Applications GAUGE NO Nominal Decimal Equivalent (Inch) Pullout Values (Average Lbs. Ultimate) FASTENER STEEL GAUGE (Lbs.) DIA. PT # # / Shear Values (Average Lbs. Ultimate) FASTENER STEEL GAUGE (Lapped) DIA. PT # # / Fastener Values FASTENER (Dia-tpi) TENSILE (Lbs. Min) SHEAR (Avg. Lbs. Ultimate) TORQUE (Min. in Lbs.) The values listed are ultimate averages achieved under laboratory conditions and apply to Buildex manufactured fasteners only. Appropriate safety factors should be applied to these values for design purposes. B 7

8 TEKS Self-Drilling Fasteners The Best Point Ever for Speed and Consistency DESCRIPTION/ADVANTAGES Medium Duty Steel-To-Steel Applications TEKS Self-Drilling Fasteners SPECIFICATIONS Diameter / Thread Form /4-14 Point has precise cutting edges to improve drill performance with less effort. Non-walking point provides fast material engagement. Point to thread design maximizes pullout performance and minimizes backout. Drills and taps in the broadest range of applications. Climaseal finish provides excellent corrosion resistance and lower tapping torque. Head Style Hex Washer Head (HWH) Drill Point Teks 2 Teks 3 Finish Type Kesternich Results Salt Spray Results (DIN 50018, 2.OL) (ASTM B117) Electro-zinc (EZ) 3 cycles - 5% or less red rust 48 hours - 5% or less red rust Climaseal Coating (CL) 30 cycles - 10% or less red rust 1000 hours - 10% or less red rust Climaseal + Coating (CL+) Meets or exceeds Kesternich and Salt Spray Results of Climaseal Coating (CL) INSTALLATION INSTRUCTIONS 1. A standard screwgun with a depth sensitive nosepiece should be used to install Teks. For optimal fastener performance, the screwgun should be a minimum of 6 amps and have a RPM range of Adjust the screwgun nosepiece to properly seat the fastener. 3. New magnetic sockets must be correctly set before use. Remove chip build-up as needed. 4. The fastener is fully seated when the head is flush with the work surface. 5. Overdriving may result in torsional failure of the fastener or stripout of the substrate. 6. The fastener must penetrate beyond the metal structure a minimum of 3 pitches of thread. B 8

9 TEKS Medium Duty Steel-To-Steel Applications APPROVALS/LISTINGS Roof deck to steel framing. Wall panel to girt. Duct work to steel framing. Accessories to steel framing Clip to steel framing. Retrofit framing. Factory Mutual (J.I. 2 X 9A2 AM) ICC - ESR 1976 DRILL POINTS Teks 2 Teks 3 SELECTION CHART TEKS Fasteners PART REFERENCE DESCRIPTION Finish: Climaseal Coating. HEAD STYLE DRILL POINT DRILL & TAP CAPACITY MAX. MATERIAL ATTACHMENTS BOX QTY P PAK QTY x 3/4" 5/16" HWH # ,000 - Duct work to steel framing P x 1" 5/16" HWH # , x 1-1/4" 5/16" HWH # , x 1-1/2" 5/16" HWH # , x 2" 5/16" HWH # , /4-14 x 3/4" 3/8" HWH # , /4-14 x 1" 3/8" HWH # , /4-14 x 1-1/4" 3/8" HWH # , /4-14 x 1-1/2" 3/8" HWH # , P 1/4-14 x 2" 3/8" HWH # , /4-14 x 2-1/2" 3/8" HWH # , /4-14 x 3" 3/8" HWH # , /4-14 x 4" 3/8" HWH # P Available in P PAK + (CL+) Coating - Accessories to steel framing - Clip to steel framing - Duct work to steel framing - Accessories to steel framing - Clip to steel framing TEKS Fasteners PART REFERENCE DESCRIPTION Finish: Electro-zinc Plating. HEAD STYLE DRILL POINT DRILL & TAP CAPACITY MAX. MATERIAL ATTACHMENTS x 3/4" 5/16" HWH # ,000 BOX QTY A/X PAK QTY A A x 1" 5/16" HWH # , A A x 1-1/2" 5/16" HWH # , A A x 2" 5/16" HWH # , Duct work to steel framing - Accessories to steel framing - Clip to steel framing /4-14 x 3/4" 3/8" HWH # , A A 1/4-14 x 1" 3/8" HWH # , A A 1/4-14 x 1-1/4" 3/8" HWH # , A A 1/4-14 x 1-1/2" 3/8" HWH # , /4-14 x 2" 3/8" HWH # , /4-14 x 3" 3/8" HWH # ,000 A Available in A PAK X Available in X PAK B 9

10 TEKS Medium Duty Steel-To-Steel Applications PERFORMANCE TABLES Sheet Steel Gauges GAUGE NO Nominal Decimal Equivalent (Inch) Pullout Values (Average Lbs. Ultimate) FASTENER Fastener Values FASTENER (Dia-tpi) TENSILE (Lbs. Min) SHEAR (Avg. Lbs. Ultimate) TORQUE (Min. in Lbs.) / STEEL GAUGE (Lbs.) DIA. PT /16 # / Shear Values (Average Lbs. Ultimate) FASTENER STEEL GAUGE (Lapped) DIA. PT # / The values listed are ultimate averages achieved under laboratory conditions and apply to Buildex manufactured fasteners only. Appropriate safety factors should be applied to these values for design purposes. B 10

11 TEKS Self-Drilling Fasteners First in Performance!! Over 30 Years of Consistent Drilling DESCRIPTION/ADVANTAGES Heavy Duty Steel-To-Steel Applications THE ORIGINAL SELF-DRILLERS FOR HEAVY DUTY TEKS Self-Drilling Fasteners SPECIFICATIONS Diameter / Thread Form 1/4-28 Unique double fluted point has precise cutting edges to improve drill performance in 1/4" thru 1/2" steel. Engineered for fast drilling and smooth tapping with less effort. Climaseal finish provides excellent corrosion resistance and lower tapping torque. Attachments up to 7.2" of material including 1/2" steel. 1/4" Diameter has notched threads to reduce tapping torque. Head Styles Hex Washer Head (HWH) Drill Point Teks 4 Teks 5 Finish Type Kesternich Results Salt Spray Results (DIN 50018, 2.OL) (ASTM B117) Climaseal Coating (CL) 30 cycles - 10% or less red rust 1000 hours - 10% or less red rust INSTALLATION INSTRUCTIONS 1. A standard screwgun with a depth sensitive nosepiece should be used to install Teks. For optimal fastener performance, the screwgun should be a minimum of 6 amps and have a RPM range of (Maximum 1800 RPM is recommended for Teks 5 fasteners) 2. Adjust the screwgun nosepiece to properly seat the fastener. 3. New magnetic sockets must be correctly set before use. Remove chip build-up as needed. 4. The fastener is fully seated when the head is flush with the work surface. 5. Overdriving may result in torsional failure of the fastener or stripout of the substrate. 6. The fastener must penetrate beyond the metal structure a minimum of 3 pitches of thread. B 11

12 TEKS Heavy Duty Steel-To-Steel Applications APPROVALS/LISTINGS Metal deck to structural steel or bar joist. Clips to structural steel or bar joist. Liner panels to structural steel or bar joist. Accessories to structural steel or bar joist. Longer length fasteners can be used in retrofit clip and sheet applications. Factory Mutual (J.I. 2 X 9A2 AM) ICC - ESR 1976 DRILL POINTS Teks 4 Teks 5 SELECTION CHART TEKS Fasteners PART REFERENCE Finish: Climaseal Coating. DESCRIPTION HEAD STYLE DRILL POINT DRILL & TAP CAPACITY MAX. MATERIAL ATTACHMENTS x 1-1/2" 5/16" HWH # ,000 BOX QTY P/X PAK QTY 1650 P P x 7/8" 5/16" HWH # , P P x 1-1/4" 5/16" HWH # , X X x 1-1/2" 5/16" HWH # , P P x 2" 5/16" HWH # , x 1-1/4" 5/16" HWH # , /4-28 x 3" 5/16" HWH # , /4-28 x 4" 5/16" HWH # /4-28 x 5" 3/8" HWH # /4-28 x 6" 3/8" HWH # /4-28 x 8" 3/8" HWH # P Available in P PAK B Available in X PAK Material Thickness (Inches) Screw Size Point 2.4mm 2.4mm 2.4mm Drill and Tap Material Thickness Chart 2.5mm mm mm.91mm 4.17mm 5.3mm 5.3mm mm.91mm.91mm 6.36mm 6.36mm mm mm 3.18mm 3.18mm 3.18mm 3.18mm mm.45mm.45mm #10 #12 1/4 #8 #12 #10 #12 1/4 #12 1/4 #12 #12 1/4 Teks/1 Teks/2 Teks/3 Teks/4 Teks/4.5 Teks/5.125 *Drill & tap capacities may vary with special feature designs. Refer to product reports for specifics. - Metal deck, clips, linear panels or accessories to structural steel or bar joist - Retrofit clip and sheet applications 12.72mm 12.72mm B 12

13 PERFORMANCE TABLES Sheet Steel Gauges TEKS Heavy Duty Steel-To-Steel Applications GAUGE NO Nominal Decimal Equivalent (Inch) Pullout Values (Average Lbs. Ultimate) Fastener Values FASTENER (Dia-tpi) FASTENER PT TENSILE (Lbs. Min.) STEEL GAUGE (Lbs.) DIA. PT /16 1/4 # / Shear Values (Average Lbs. Ultimate) FASTENER STEEL GAUGE (Lapped) DIA. PT /8 1/4 # / SHEAR (Avg. Lbs. Ultimate) TORQUE (Min. in Lbs.) / NOTE: Teks fasteners are not categorized as structural bolts. Proper design criteria and strengths must be used for satisfactory application. The values listed are ultimate averages achieved under laboratory conditions and apply to Buildex manufactured fasteners only. Appropriate safety factors should be applied to these values for design purposes. B 13

14 TEKS Self-Drilling Fasteners Low Profile Architectural Metal Roof Clip Fasteners DESCRIPTION/ADVANTAGES Low Profile Architectural Metal Roof Clip Fastener INCORPORATES THE ITW EXCLUSIVE PHILLIPS SQUARE-DRIV ANTI-CAM-OUT SYSTEM #12 diameter utilizes the ITW exclusive Phillips Square-Driv with patented interlocking components system. - Excellent installation stability. - Extended bit driver life. - Keeps the driver securely mated to the fastener during installation. - Hands-free installation. Fasteners are finished with a corrosion resistant coating. Teks 3 fasteners are available with Gray Spex coating. Sharp convex drill point has precise cutting edges to improve drill performance with less effort. Low profile pancake head style ensures proper installation of metal roof panels. SPECIFICATIONS Diameter / Thread Form Head Styles Phillips Square-Driv Pancake (PSP) Drill Point Teks 3 Finish Type Kesternich Results Salt Spray Results (DIN 50018, 2.OL) (ASTM B117) Grey Specx 15 cycles - 5% or less red rust 300 hours - 10% or less red rust Low profile architectural metal roof clips to steel purlin. Low profile architectural metal roof clips to wood supports. INSTALLATION INSTRUCTIONS 1. A standard screwgun with a depth sensitive nosepiece should be used to install Teks. For optimal fastener performance, the screwgun should be a minimum of 6 amps and have a RPM range of Adjust the screwgun nosepiece to properly seat the fastener. 3. The fastener is fully seated when the head is flush with the work surface. 4. Overdriving may result in torsional failure of the fastener or stripout of the substrate. 5. The fastener must penetrate beyond the metal structure a minimum of 3 pitches of thread. 6. New magnetic sockets must be correctly set before use. Remove chip build-up as needed. B 14

15 SELECTION CHART TEKS Low Profile Architectural Metal Roof Clip Fastener TEKS Fasteners Finish: Gray Spex Coating. PART REFERENCE DESCRIPTION HEAD STYLE DRILL POINT DRILL & TAP CAPACITY MAX. MATERIAL ATTACHMENTS BOX QTY x 1" #2 PSD # ,000 - Low profile architectural metal roof clip to steel purlin PERFORMANCE TABLES Sheet Steel Gauges GAUGE NO Nominal Decimal Equivalent (Inch) Pullout Values (Average Lbs. Ultimate) FASTENER STEEL GAUGE (Lbs.) DIA. PT # Shear Values (Average Lbs. Ultimate) FASTENER STEEL GAUGE (Lapped) DIA. PT 20 GAUGE 18 GAUGE 16 GAUGE 14 GAUGE # Fastener Values FASTENER (Dia-tpi) PT TENSILE (Lbs. Min.) SHEAR (Avg. Lbs. Ultimate) TORQUE (Min. in Lbs.) The values listed are ultimate averages achieved under laboratory conditions and apply to Buildex manufactured fasteners only. Appropriate safety factors should be applied to these values for design purposes. B 15

16 TEKS Wood to Metal Fasteners No Pre-Drilling, Fast, Efficient Attachment of Wood-To-Metal DESCRIPTION/ADVANTAGES Wood-To-Metal Applications TEKS Wood to Metal Self-Drilling Fasteners SPECIFICATIONS Diameter / Thread Form /4-20 Point has precise cutting edges to improve drill performance with less effort. Special winged fasteners ream a hole in wood preventing thread engagement during drilling. Wafer head design has a large bearing surface ideal for plywood. Flat head design countersinks and seats flush in wood. Gray Spex finish provides excellent corrosion resistance and lower tapping torque. Compatible with ACQ treated wood. Head Styles Socket Wafer Head (SW) Philips Flat Head (PFH) Drill Point Teks 3 Teks 4 Finish Type Kesternich Results Salt Spray Results (DIN 50018, 2.OL) (ASTM B117) Electro-zinc (EZ) 3 cycles - 5% or less red rust 48 hours - 5% or less red rust Grey Specx 15 cycles - 5% or less red rust 300 hours - 10% or less red rust INSTALLATION INSTRUCTIONS 1. A standard screwgun with a depth sensitive nosepiece should be used to install Teks. For optimal fastener performance, the screwgun should be a minimum of 6 amps and have an RPM range of Adjust the screwgun nosepiece to properly seat the fastener. 3. Worn or damaged bit tip should be replaced. 4. The fastener is fully seated when the head is flush with the work surface. 5. Overdriving may result in torsional failure of the fastener or stripout of the substrate. 6. The fastener must penetrate beyond the metal structure a minimum of 3 pitches of thread. 7. All #10 diameter Winged parts must be driven into a minimum of 16 GA steel thickness. 8. All 1/4 and #12 diameter Winged parts must be driven into a minimum of 1/8" steel in order to break the wings consistently. B 16

17 TEKS Wood-To-Metal Applications DRILL POINTS Plywood roof and floor sheet to steel frames. 2 x 4 headers to steel frames. Plywood fascia to steel frames. Teks 3 Teks 4 Drill and Tap Material Thickness Chart Material Thickness (Inches) Screw Size Point 2.4mm 2.4mm 2.4mm mm mm mm.91mm 4.17mm 5.3mm 5.3mm mm.91mm.91mm 6.36mm 6.36mm mm mm.45mm.45mm #10 #12 1/4 #8 #12 #10 #12 1/4 #12 1/4 #12 #12 1/4 Teks/1 Teks/2 Teks/3 Teks/4 Teks/4.5 Teks/ mm 12.72mm mm 3.18mm 3.18mm 3.18mm 3.18mm *Drill & tap capacities may vary with special feature designs. Refer to product reports for specifics. SELECTION CHART TEKS Fasteners PART REFERENCE DESCRIPTION HEAD STYLE Finish: Electro-zinc Plating. Without Wings. DRILL POINT DRILL & TAP CAPACITY WOOD ATTACHMENT RANGE BOX QTY X PAK QTY A PAK QTY X X A x 1" #2 SW # /4"-1/2" 5, Plywood, mansard, fascia, X X x 1-1/4" #2 SW # /4"-3/4" 3, roofing, flooring to steel framing X Available in X PAK A Available in A PAK TEKS Fasteners PART REFERENCE DESCRIPTION Finish: Electro-zinc Plating. With Wings. HEAD STYLE DRILL POINT DRILL & TAP CAPACITY WOOD ATTACHMENT RANGE BOX QTY P PAK QTY X PAK QTY X P B x 1-1/2" #2 SW # /4"-1" 3, Plywood, 2 x 4 s to steel framing P P x 2" #3 SW # /4" - 1" 2, P x 2-1/2" #3 SW # /4"-1-1/2" 1, P P x 3" #3 SW # /4"-2" 1, P Available in P PAK X Available in X PAK B 17

18 TEKS Wood-To-Metal Applications SELECTION CHART TEKS Fasteners Finish: Gray Spex Coating. With Wings. PART REFERENCE DESCRIPTION HEAD STYLE DRILL POINT DRILL & TAP CAPACITY WOOD ATTACHMENT RANGE BOX QTY /4-20 x 3" #3 PFH # /4"-2" 1, x 2-1/4" #3 PFH # /4"- 1-3/8" 2, x 2-3/4" #3 PFH # /4"-2-5/8" 1,600 - Plywood, 2 x 4 s to steel framing PERFORMANCE TABLES Sheet Steel Gauges GAUGE NO Nominal Decimal Equivalent (Inch) Pullout Values (Average Lbs. Ultimate) FASTENER Fastener Values FASTENER (Dia-tpi) TENSILE (Lbs. Min) SHEAR (Avg. Lbs. Ultimate) TORQUE (Min. in Lbs.) / STEEL GAUGE Lbs.) DIA. PT /16 1/4 # # # / Shear Values (Average Lbs. Ultimate) FASTENER STEEL GAUGE (Lapped) DIA. PT /8 # # / The values listed are ultimate averages achieved under laboratory conditions and apply to Buildex manufactured fasteners only. Appropriate safety factors should be applied to these values for design purposes. B 18

19 TEKS with Bonded Washer For Weather-Tight Sealing of Roof and Wall Applications DESCRIPTION/ADVANTAGES Metal Roof and Wall Applications TEKS with Bonded Washer SPECIFICATIONS Diameter / Thread Form /4-14 1/4-28 Vulcanized bonding of washer eliminates separation of EPDM from the metal backing. Dual sealing bonded washer prevents leaks. Climaseal finish provides excellent corrosion resistance and lower tapping torque. Point has precise cutting edges to improve drill performance with less effort. Point to thread design maximizes pullout performance and minimizes backout. Head Styles Hex Washer Head with Bonded Washer(HWH) Washer Style Galvanized (G-90) Drill Point Teks 1 Teks 2 Teks 3 Teks 4 Teks 5 Finish Type Kesternich Results Salt Spray Results (DIN 50018, 2.OL) (ASTM B117) Climaseal Coating (CL) 30 cycles - 10% or less red rust 1000 hours - 10% or less red rust Climaseal + Coating (CL+) Meets or exceeds Kesternich and Salt Spray Results of Climaseal Coating (CL) INSTALLATION INSTRUCTIONS 1. A standard screwgun with a depth sensitive nosepiece should be used to install Teks. For optimal fastener performance, the screw gun should be a minimum of 6 amps and have an RPM range of New magnetic sockets must be correctly set before use Remove chip build-up as needed. 3. Adjust the screwgun nosepiece to properly seat the fastener. 4. Overdriving may result in torsional failure of the fastener or stripout of the substrate. 5. The fastener must penetrate beyond the metal structure a minimum of 3 pitches of thread. B 19

20 TEKS Metal Roof and Wall Applications DRILL POINTS Roof panels to purlin or bar joist. Wall panels to girt. Mansard panel to structural. Teks 1 Teks 2 Teks 3 Teks 4 Teks 5 Drill and Tap Material Thickness Chart PROPERLY SEATED WASHERS Underdriven Correctly Driven Overdriven SELECTION CHART TEKS w/bonded Washer PART REFERENCE DESCRIPTION Finish: Climaseal Coating. HEAD STYLE WASHER DIAMETER DRILL POINT DRILL & TAP CAPACITY MAX. MATERIAL ATTACHMENTS x 3/4" 5/16" HWH 9/16" # , W x 3/4" 5/16" HWH 9/16" # , W x 1" 5/16" HWH 9/16" # , W x 1-1/2" 5/16" HWH 9/16" # , W x 2" 5/16" HWH 9/16" # , W /4-14 x 7/8" 5/16" HWH 9/16" # , W /4-14 x 1" 3/8" HWH 9/16" # , W 1/4-14 x 1-1/2" 3/8 HWH 9/16 # , W /4-14 x 2" 3/8" HWH 9/16" # , W x 1-1/4" 5/16" HWH 9/16" # , W x 1-1/2" 5/16" HWH 9/16" # , W x 2" 5/16" HWH 9/16" # , /4-28 x 3" 5/16" HWH 9/16" # , /4-28 x 4" 5/16" HWH 9/16" # /4-28 x 5" 3/8" HWH 3/4" # (CL+) Coating Material Thickness (Inches) Screw Size Point 2.4mm 2.4mm 2.4mm mm mm mm.91mm 4.17mm 5.3mm 5.3mm mm.91mm.91mm mm.45mm.45mm #10 #12 1/4 #8 #12 #10 #12 1/4 #12 1/4 #12 #12 1/4 Teks/1 Teks/2 Teks/3 Teks/4 Teks/4.5 Teks/5 *Drill & tap capacities may vary with special feature designs. Refer to product reports for specifics. BOX QTY 6.36mm 6.36mm mm mm 3.18mm 3.18mm 3.18mm 3.18mm - Brick tie to steel framing - Mansard panel to steel framing - Roof panel to purlin - Stitch roof 12.72mm 12.72mm B 20

21 PERFORMANCE TABLES Sheet Steel Gauges GAUGE NO Nominal Decimal Equivalent (Inch) Pullout Values (Average Lbs. Ultimate) FASTENER Fastener Values FASTENER (Dia-tpi) TENSILE (Lbs. Min.) SHEAR (Avg. Lbs. Ultimate) TORQUE (Min. in Lbs.) / / STEEL GAUGE (Lbs.) DIA. PT /16 1/4 # #12 #12 1/4 Shear Values (Average Lbs. Ultimate) FASTENER TEKS Metal Roof and Wall Applications STEEL GAUGE (Lapped) DIA. PT /8 1/4 # #12 #12 1/ The values listed are ultimate averages achieved under laboratory conditions and apply to Buildex manufactured fasteners only. Appropriate safety factors should be applied to these values for design purposes. B 21

22 DEKSTRIP Expandable Edged Flashing Stretches to Any Shape, Seals and Stays DESCRIPTION/SUGGESTED SPECIFICATIONS Pipe Flashing Applications DEKSTRIP is a flexible neoprene product that is completely chemical resistant. It has an aluminum bar embedded in it to form & follow the various corrugations of your roof. ADVANTAGES Wraps around almost any profile Paintable after installation TPE has a continuous service temperature range of -50 C to +115 C 20 year warranty Serpentine edges stretch up to 25% for added length Great for large round pipes Handles vibration & expansion DEKSTRIP B 22

23 DEKSTRIP Expandable Edged Flashing INSTALLATION INSTRUCTIONS Large square & round ducts & penetrations BASIC Chimneys Skylights Parapet Flashing Expansion Joints Stepped Roof Dissimilar roof profiles Transition wall 1. Snap a chalk line to provide a guide for applying sealant. Gambrel roof Flash between dissimilar materials 2. Apply a continuous bead of sealant along chalk line. SPECIFICATIONS Material Grey TPE 3. Position top edge of Dekstrip over seal bead and install Buildex fasteners at 1-1/2" maximum intervals on top edge. Repeat steps 1, 2, and 3 for the bottom edge. Base Kit Contents Dekstrip material 1" x 4' Aluminum termination strip 3" x 2' Splice tape 4. Apply additional sealant to both fastened edges for maximum weather-tight sealing. B 23

24 DEKSTRIP Expandable Edged Flashing INSTALLATION INSTRUCTIONS SPLICING MATERIALS NEEDED: Leather Gloves Heat Gun 3" x 2' splice tape Shears or scissors 1. Apply splice tape to Dekstrip. 2. Position second Dekstrip over tape & press in place. 3. Apply heat and press firmly to seal edges. DETAILED INSTRUCTIONS 1. Cut splice tape (supplied in Dekstrip carton) to the width needed and remove clear film from one side of the tape. Lining up the edges, press the tape firmly onto the Dekstrip to remove air pockets. 2. Remove remaining film from tape. Apply second piece of Dekstrip over tape and press firmly. 3. Apply heat over spliced area for 1-2 minutes while applying firm pressure over entire spliced area to ensure adhesion. 4. Turn material over and repeat step 3. JOINING ENDS AROUND ROUND PIPES DETAILED INSTRUCTIONS 1. Cut splice tape to length, remove film from one side and apply to Dekstrip. 2. Remove film from top of splice tape. 3. Overlap top piece of Dekstrip and press onto tape. 4. Fold termination strip in half, cut to width, and slide over spliced area and apply to Dekstrip. 5. Fasten through top of termination strip, Dekstrip, and back of strip with Scots fasteners or rivets. 6. Apply sealant to all seams SELECTION CHART DEKSTRIP Expandable Edged Flashing PART REFERENCE DESCRIPTION WEIGHT FASTENERS NEEDED (1-1/2" O.C.) " x 75' 31 lbs " x 75' 38 lbs " x 50' 30 lbs. 800 B 24

25 Dektite and Retrofit Dektite The Original Flexible Pipe Flashing System with a 20 Year Warranty. Standard Dektite DESCRIPTION/SUGGESTED SPECIFICATIONS Pipe Flashing Applications Dektite Will not crack or break. Dekite can be installed over or between the ribs of standard panels. Generally no sealant is required where the Dektite collar provides a compression fit around the pipe. Standard Dektite ADVANTAGES Retrofit Dektite Made of long life, flexible, weatherproof gray EPDM rubber or red silicone. Flexible, corrosion resistant aluminum base conforms to any panel configuration. EPDM and silicone will not crack or break. Pipe diameter markings are clearly indicated for accurate fitting. Designed for 1/4" to 18" diameter pipes. Pleated cone adjusts to any roof pitch and allows for complete flexibility. Step Design vs Dektite No size markings on step design. Dektite underside rib height is 54% lower than step design, resulting in better drainage % -35.1% Retrofit Dektite makes difficult installations a breeze! Wraps around existing or difficult to access pipes. Snaps together in seconds. The built-in crimp means no loose clips or rivets. Grips tight and stays tight. The supple aluminum base conforms to metal profiles One piece construction is easy to install. EPDM has a continuous service temperature range of -53 C to +121 C. Silicone has a continuous service temperature range of -40 C to +176 C Proven resistance to ozone and ultra-violet light. Thickness of the cone, particularly at stress points, considerably impacts on the life span of the flashing. Dektite is up to 66% thinker in some areas over the competition. Step design has exposed corner angles that become vulnerable to degradation when stretched. Step product is WT% thinner compound in critical areas. -54% Retrofit Dektite PHYSICAL PROPERTIES Product Comparison Dektite with Silicone Needs loose clips to join ends. Needs band to seal pipe. Needs sealant applied to base, seam & pipe seam join. Fully integrated waterproof seam joint Seals by strong compound & good design Only needs a sealant on roof and top of seam -24.8% % 3.30mm 7.65mm mm -23.4% 2.57mm 3.171mm -.28% 2.47mm 2.54mm Other Retrofit -12.5% 3.53mm 3.97mm Dektite Retrofit Dektite with wires PRODUCT COMPARISON B 25

26 Dektite and Retrofit Dektite Plumbing Heating Air Conditioning Electrical and Exhaust Vents INSTALLATION INSTRUCTIONS Dektite Cut Dektite at appropriate pipe diameter marking. 2. Slide Dektite flashing down over pipe. 3. Apply sealant on underside of flexible aluminum base. 4. Press Dektite base into contours of panel configuration. 5. Fasten Dektite to surface with Buildex Scots self-drilling fasteners. Apply additional sealant around base if desired. Notes: Dekite can be installed over or between the ribs of standard panels. Can be installed between the rib sections of a Standing Seam Roofs or Architectural Panel. Do Not install over the rib section of the SSR or Architectural Panel ribs. Generally no sealant is required where the Dektite collar provides a compression fit around the pipe. However, some metal pipes and flues include a seam which may require a local application of sealant at the point where the Dektite colla crosses the seam. Retrofit Dektite SPECIFICATIONS Pipe Diameter Ranges 1/4" to 18" Dektite 3/4" to 10" Retrofit Dektite 1/4" to 18" Silicone Materials EPDM Standard and Retrofit Silicone High Temperature Replace with Recommend Sealant: Flexible, Polyurethane-based elastomeric Sealant Begin cutting opposite of the mechanical locking joiner. Cut through the joiner with tin snips. 2. Wrap Retrofit Dektite around the pipe. Engage the top section of the joiner first, then proceed down until joiner is completely engaged. 3. Crimp joiner tightly, starting at the top by squeezing joiner fingers with pliers. 4. Apply sealant to the underside of the ribbed aluminum base. Press Retrofit Dektite against contours of the panel configuration. 5. Attach Retrofit Dektite to the panel with SCOTS self-drilling screws. Screws should be spaced as necessary to avoid gaps between the base and the panel. 6. Apply additional sealant around the top of the Dektite, near the mechanical locking joiner seam. B 26

27 Dektite and Retrofit Dektite SELECTION CHART Dektite Flashing PART REFERENCE DESCRIPTION PIPE OUTSIDE DIAMETER DEKTITE BASE DIAMETER DEKTITE HEIGHT #1 EPDM 1/4" - 2" 4-3/4" 3" #2 EPDM 1-3/4" - 3-1/4" 6-1/4" 4" #3 EPDM 1/4" - 4" 7-3/4" 4" #4 EPDM 3" - 6" 9-1/4" 5" #5 EPDM 4" - 7" 10-3/4" 5" #6 EPDM 5" - 9" 12-1/2" 6" #7 EPDM 6" - 11" 14-1/2" 6" #8 EPDM 7" - 13" 16-1/2" 6" #9 EPDM 10" - 18" 25-3/8" 8" #3 Silicone 1/4" - 4" 7-3/4" 4" #5 Silicone 4" - 7" 10-3/4" 5" #8 Silicone 7" - 13" 16-1/2" 6" #9 Silicone 10" - 18" 25-3/8" 8" 2 Note: When used on roofs where pitch is steeper than 20 degrees, or when used on deep ribbed profile roof panel (1-1/2" deep corrugation or more), consider using next larger size Dektite that will accommodate the same pipe diameter. Flexible, Polyurethane-based elastomeric Sealant. Recommended Fastener: 1/4-14 x 7/8" Scots Teks /1, part number BOX QTY Retrofit Dektite PART REFERENCE DEKTITE SIZE PIPE OUTSIDE DIAMETER DEKTITE BASE DIAMETER DEKTITE HEIGHT EPDM 3/4" - 2-3/4" 6-3/10" 3-1/2" EPDM 2" - 7-1/4" 10-3/4" 5-3/5" EPDM 3-1/4" - 10" 14-1/2" 5-4/5" 5 BOX QTY PERFORMANCE TABLE Dektite Flashing ASTM METHOD TEST DESCRIPTION SPECIFICATION TEST RESULTS D412 Tensile Strength (min. psi rating) 1450 psi min psi D412 Ultimate Elongation (%) 350 min. 535 D1171 Resistance to Ozone-min. rating 100 (no cracks) Passed D673 Heat Aging - 70 hrs. at 100 C Change in Hardness (points) Change in Tensile Strength (%) Change in Elongation (%) ± 15 max. ± 30 max. ± 50 max ASTM METHOD D2137 D624 TEST DESCRIPTION Low Temperature Brittleness- 3 mins. at -40 C Tear Resistance Die C (min.) per inch of width min. SPECIFICATION Non-brittle 125 pounds per inch of width TEST RESULTS Passed 130 pounds U.L. 94 Flame Resistance U.S. 94 H.B. Passed B 27

28 DESCRIPTION/ADVANTAGES TAPCON Concrete and Masonry Anchors Light-To-Medium Duty Masonry Applications The original masonry anchor that cuts its own threads into concrete, brick, or block. Maximum performance is achieved because the Tapcon Anchor, the Condrive Installation Tool, and the carbide-tipped Tapcon Drill Bits are designed to work as a system. It is essential to use the Condrive tool and the correct drill bit to assure consistent anchor performance. ADVANTAGES Fast installation... drill a hole... drive an anchor. Packaged with one Tapcon close tolerance masonry drill bit per 100 anchors. Also available in bulk packaging. Available in 3/16" diameter up to 4" in length and 1/4" diameter up to 6 in length. Compatible for use in ACQ treated wood. Tapcon Anchors Replaces small diameter expansion anchors, plugs and screws in light to medium duty applications. No need to pre-spot holes... and no inserts are required. Reversible and removable... can be installed close to an edge. Hex Head style on Tapcon Anchors is available for majority of fixture anchoring needs Climaseal Coating is standard on all Tapcon anchors to provide extended corrosion resistance Phillips Flat Head style is available when flush seating is necessary in countersink applications Advanced Threadform cuts into masonry materials for greater pullout values Lengths of Tapcon Anchors range from 1-1/4" to 4" in 3/16" and up to 6" in 1/4" diameters. Nail-Type Point guides the anchor into the pre-drilled hole. Excellent for wood to concrete applications SPECIFICATIONS Diameter 3/16" and 1/4" Thread Form Advanced Threadform Technology Head Style Point Type Finish Flat and Hex Head Nail Blue Climaseal B 28

29 Tapcon Concrete and Masonry Anchors APPROVALS/LISTINGS Electrical junction boxes and conduit clips to masonry. Wood headers and furring strips to masonry HVAC strapping to masonry. Plywood backer boards to masonry. Exterior insulation systems to masonry. Miami Dade County Product Control Approved RR25644 ICC-ESR 1671 Masonry ICC-ESR 2202 Concrete City of Los Angeles INSTALLATION STEPS Read instructions before using (installation)! WARNING: If there are any questions concerning proper installation, applications or appropriate use of this product, please call our Technical Services Department at Failure to follow these instructions can result in serious personal injury. INSTALLATION TOOL GUIDELINES Tapcon Condrive Pro Installation Kit A one-tool system engineered to work with all impact drivers, rotary hammers and hammer drills, the Tapcon Pro Installation Kit can drill and drive. The Condrive is designed to speed up anchor installation and enhance jobsite productivity. It features recessed hex drivers designed to significantly reduce over-torquing, head snapping and strip outs, allowing PROs to anchor with confidence and efficiency the first time, every time. PREPARATION 1. Place correct Tapcon drill bit in drill adapter and tighten set screw with hex key (included). For rotary hammer begin at Step Secure drill adapter into 3/8" 1/2" chuck of hammer drill or into 1/4" impact hammer 3. Attach appropiate hex driver or Phillips bit to end of sleeve. DRILL 4. Drill hole 1/4" deeper than depth of anchor embedment. (Min. embedment 1"). Remove dust from hole. SLIDE 5. Slide sleeve over drill bit and snap into drill adapter DRIVE 6. Insert anchor into the end of the sleeve, position fixture to be fastened and drive the Tapcon Buildex Condrive Tools are designed to specifically install Tapcon Anchors and to fit standard hammer drills. 1. Select proper fastener diameter / head style / length a) Use selection chart to choose proper length. 2. Drill Hole use selection chart to determine drill bit length and depth of hole a) Choose appropriate drill bit based upon diameter of Tapcon Anchor. b) Drill hole minimum ¼" deeper than Tapcon Anchor to be embedded. Minimum anchor embedment: 1" Maximum anchor embedment: 1-3/4" 3. Drive Anchor WARNING: WARNING: HEAD STYLES Failure to wear safety glasses with side shields can result in serious personal injury. Always wear ANSI compliant eye protection (ANSI Z ). Using the wrong size drill bit will affect performance values and may cause failure. 3/16" diameter has a 1/4" slotted hex washer head (HWH) 1/4" diameter has a 5/16" slotted hex washer head (HWH) 3/16" diameter uses a #2 phillips flat head (PFH) 1/4" diameter uses a #3 phillips flat head (PFH) B 29

30 Tapcon Concrete and Masonry Anchors SELECTION CHART Tapcon Anchors 3/16" Diameter PART 1/4" HWH PART #2 PFH DESCRIPTION FIXTURE THICKNESS STRAIGHT SHANK DRILL BIT PART DRILL BIT DESCRIPTION BOX QTY CASE QTY BULK QTY 3010 BK 3110 BK 3/16" x 1-1/4" 0-1/4" /32" x 3-1/2" , BK 3120 BK 3/16" x 1-3/4" 0-3/4" /32" x 3-1/2" , BK 3130 BK 3/16" x 2-1/4" 1/2" - 1-1/4" /32" x 4-1/2" , BK 3140 BK 3/16" x 2-3/4" 1" - 1-3/4" /32" x 4-1/2" , BK 3160 BK 3/16" x 3-1/4" 1-1/2" - 2-1/4" /32" x 5-1/2" , /16" x 4" 2-1/4" - 3" /32" x 5-1/2" Tapcon Anchors must be installed using all Buildex system components (Tapcon Anchors, Condrive Tools and Tapcon Drill Bits) in order to qualify for ITW Buildex system support. BK Available in Bulk Pack Qty Tapcon Anchors 1/4" Diameter PART 5/16" HWH PART #3 PFH DESCRIPTION FIXTURE THICKNESS STRAIGHT SHANK DRILL BIT PART DRILL BIT DESCRIPTION 3210 BK 3310 BK 1/4" x 1-1/4" 0-1/4" /16" x 3-1/2" , BK 3320 BK 1/4" x 1-3/4" 0-3/4" /16" x 3-1/2" , BK 3330 BK 1/4" x 2-1/4" 1/2" - 1-1/4" /16" x 4-1/2" , BK 3340 BK 1/4" x 2-3/4" 1" - 1-3/4" /16" x 4-1/2" , BK 3350 BK 1/4" x 3-1/4" 1-1/2" - 2-1/4" /16" x 5-1/2" BK 3370 BK 1/4" x 4" 2-1/4" - 3" /16" x 5-1/2" BK 3380 BK 1/4" x 5" 3-1/4" - 4" /16" x 6-1/2" BK /4" x 6" 4-1/4" - 5" /16" x 7-1/2" Tapcon Anchors must be installed using all Buildex system components (Tapcon Anchors, Condrive Tools and Tapcon Drill Bits) in order to qualify for ITW Buildex system support. BK Available in Bulk Pack Qty BOX QTY CASE QTY BULK QTY Accessories PART DESCRIPTION BOX QTY 7001 Condrive Pro Installation Kit 4 BX /32 x 4-1/2 Tapcon Drill Bit 10 BX /16 x 4-1/2 Tapcon Drill Bit 10 BX /32 x 3-1/2 Tapcon Drill Bit 10 BX /16 x 3-1/2 Tapcon Drill Bit 10 BX /16 x 5-1/2 Tapcon Drill Bit 10 BX /32 x 5-1/2 Tapcon Drill Bit C 3/16 x 7 SDS Plus Tapcon Drill Bit C 5/32 x 7 SDS Plus Tapcon Drill Bit 10 CONDRIVE PRO ADVANTAGES Works with all Impact Drivers, Rotary Hammers, Hammer Drills, Tapcon SDS and Carbide Straight Shank Bits. Fast and Easy: only one tool needed to drill and drive Recessed Hex Driver reduces overtorquing, head snapping, and spinouts Fits fully assembled in carrying pouch for easy storage Tapcon SDS Plus Drill Bits are specially designed to be compatible with Condrive Pro Installation Kit. Use the Tapcon bits and Condrive Pro together to install Tapcon anchors for optimal performance. B 30

31 Tapcon Concrete and Masonry Anchors PERFORMANCE TABLES Tension Values (In Normal-Weight Concrete Lbs.) ANCHOR DIAMETER EMBEDMENT DEPTH CONCRETE STRENGTH 2000 PSI 4000 PSI 5000 PSI 1" /16 1-1/2" /4" " /4 1-1/2" /4" Tension and Shear Values (In CMU 1" Embedment) ANCHOR DIAMETER TENSION (Lbs.) SHEAR (Lbs.) LIGHT WEIGHT MEDIUM WEIGHT LIGHT WEIGHT MEDIUM WEIGHT 3/ / For minimum edge distance and spacing distance, please refer to the ICC-ES report or Miami-Dade report for this product. Lightweight and medium-weight Concrete Masonry Units (CMU) were defined by ASTM C 90. Shear Values (In Normal-Weight Concrete Lbs.) ANCHOR DIAMETER EMBEDMENT DEPTH CONCRETE STRENGTH 2000 PSI 4000 PSI 5000 PSI 1" /16 1-1/2" /4" " /4 1-1/2" /4" NOTE: Indicated tension and shear failure values were obtained in tests conducted at CEL Consulting. Designated holding power depends on the quality of the masonry material, depth of embedment and proper hole size. These figures are offered only as a guide and are not guaranteed in any way by Illinois Tool Works Inc. The figures indicate average ultimate tension and shear failure values. A safety factor of 4:1 or 25% of ultimate value is generally accepted as a safe working load. However, reference should always be made to applicable codes for the specific safe working ratio. All values are based on close tolerance holes drilled with Buildex Tapcon carbide drill bits. Performance of the Tapcon anchor may vary in extremely hard concrete aggregates. Consult your Buildex representative for further information. As in the case with all applications, Buildex can only suggest typical fasteners for typical applications and that the connection design is the sole responsibility of the Building Design Engineer, Architect or otherwise responsible person charged with the design of the connection. For further product information, please contact the nearest Authorized Buildex Distributor or the Buildex Technical Service Department at B 31

32 TAPCON Ceiling Anchor DESCRIPTION Tapcon Ceiling Anchors This innovative anchoring system allows the installer to conduct the installation from the ground for ceiling heights 18 foot or lower. The patented pole system allows the installer to drill the hole from the ground through hard to reach areas where pipes and duck work get in the way. The driving mechanism will also tie the wire after the anchor is fully set. ADVANTAGES Install the anchor from the ground. Eliminating the need for scaffolds or expensive scissor lifts and increase your output. No need to set the anchor using a claw hammer. Just drive the anchor in using the installation tool and your are done. Anchors can easily be inspected for correct installation. No need to pay more for a 1/4" drill bit. This anchor requires a 3/16" carbide bit so you can drill faster with less effort. Reversible and removable...can be installed close to an edge. Tie-Wire Head accommodates up to 3/16" wire. SUGGESTED SPECIFICATIONS The fastener used to suspend T-Bar, Gypsum Wall Board Ceilings, or Light Fixtures in Concrete shall be Buildex Tapcon Ceiling Anchor 1/4" x 1-1/4" with Blue Climaseal Coating (TCA-114). TCA allows for easy access through pipes and obstacles. T-Bar ceiling, gypsum wall board ceiling, and safety chains for light fixtures. SELECTION CHART Tapcon Ceiling Anchors PART DESCRIPTION BOX QTY TCA-114 T1-1/4" Tapcon Ceiling Anchor 1000 SP4 TCA Pole for installing 1 TCA-I TCA-I Driver for pole tool 1 B 32

33 Tapcon Ceiling Anchors PERFORMANCE TABLES Ultimate Tension & Shear Values In 4000 PSI Normal-Weight Concrete (Lbs.) ANCHOR DIAMETER ANCHOR EMBEDMENT ULTIMATE TENSION (Lbs.) ULTIMATE SHEAR (Lbs.) 1/4" 1-1/4" 1,310 1,370 Allowable Edge and Spacing Distances In Normal-Weight Concrete (Lbs.) PARAMETER FULL CAPACITY (Critical Distance Inches) REDUCED CAPACITY (Minimal Distance Inches) LOAD REDUCTION FACTOR Spacing - Tension Spacing - Shear Edge Distance - Tension 2-1/2 1-1/ Edge Distance - Shear 3 1-1/ INSTALLATION STEPS 1. Drill hole 1-1/2" deep into the concrete using a 3/16" ANSI Carbide Drill Bit. 4. Install the Tapcon Ceiling Anchor using a 18v cordless drill with a clutch feature until the anchor collar is flush with the concrete surface. 2. Insert Tapcon Ceiling Anchor into the TCA driver. 5. Pull on the installation pole tool until the head of the anchor is free from the TCA driver. 3. Feed tie wire rod through the TCA driver and the Tapcon Ceiling Anchor. Align Tapcon Ceiling Anchor to 3/16" hole 6. Turn the pole tool using the cordless drill until the tie wire rod is securely fastened into itself. B 33

34 E-Z Drywall Anchors DESCRIPTION/SUGGESTED SPECIFICAITONS Drywall Anchor Applications E-Z Ancor Self-Drilling Anchor The E-Z Ancor is a one-piece self-drilling anchor designed for optimal holding performance in gypsum wallboard. Available in zinc or high strength engineered plastic (non-conductive). Ideal anchor for 3/8", 1/2" and 5/8" gypsum wallboard. The Original! Fast and Easy Self-Drilling Anchors ADVANTAGES No hole preparation necessary; pre-drills own small precise hole in gypsum wallboard. Replaces plastic plugs and toggles. Deep thread design provides strong engagement in 3/8" 1/2" and 5/8" gypsum wallboard. Installs quickly and easily with a phillips screw-driver or square drive bit. Full range of anchors to cover all wall fastening applications. Available in corrosion resistant, non-conductive white nylon. Can be easily backed-out. Low profile head. Single point designs for clean cutting installation. E-Z Ancors E-Z Mini E-Z E-Z E-Z Mini Twist-N-Lock Ancor Twist-N-Lock Toggle B 34

35 Electrical Fixtures Plaques and Awards Thermostats Closet Organizers HVAC Fixtures Coat Racks Plumbing Fixtures Curtain Rods Bathroom Accessories Signs Shelving and Supports Bulletin Boards Mirrors Control Systems Picture Frames Decorative Wall Hangings Brackets Office Material Holders Smoke Detectors Clocks Kitchen Accessories Doorbells Telecommunications Equipment Chalk Boards Remote Control Boxes E-Z Drywall Anchors INSTALLATION INSTRUCTIONS LIGHT DUTY & MEDIUM DUTY E-Z ANCORS 1. Place #2 Phillips screwdriver into recess of E-Z Zinc, E-Z Lite, E-Z Mini, E-Z Stud Solver, Twist-N-Lock, or E- Z Plastic Plus. 2. Press into drywall while turning the anchor clockwise until it is seated flush with wall. 3. Place fixture in position over installed E-Z Zinc, E-Z Lite, E-Z Mini, E-Z Stud Solver, Twist-N-Lock, or Plastic Plus. Insert screw with screw driver. Tighten fixture in place. SPECIFICATIONS Material Drilling Capacity Zinc die cast, Carbon, Steel, Nylon PERFORMANCE TABLE E-Z Ancors 3/8", 1/2" and 5/8" gypsum wallboard DRYWALL THICKNESS HOLDING WEIGHT (lbs.) Gypsum Board Thickness 3/8" 1/2" 5/8" HEAVY DUTY E-Z TOGGLE 1. Using a #2 Phillips screwdriver, drill the E-Z Toggle Anchor into drywall until the head of the anchor is seated flush. 2. To set the clamp behind the drywall, place the mounting screw into the anchor and push or tap firmly until approximately 1" of screw is protruding (do not rotate). Then remove the screw. 3. Place fixture over E-Z Toggle, insert screw and continue to turn until fastened tightly (for example when attaching a 1/2" thick fixture, it will require approx. 23 full rotations of the screwdriver to fully tighten the fixture). EZ Mini and Mini Twist-N-Lock E-Z Anchor and EZ Stud Solver Twist-N-Lock E-Z Toggle These performance values are averages obtained under laboratory conditions. Note that these values will change depending on age, moisture content and surface treatment of the drywall (gypsum) material. Appropriate safety factors should be applied to these values for design purposes. SELECTION CHART E-Z Ancors PART WITH SCREWS PART WITHOUT SCREWS DESCRIPTION MATERIAL MAXIMUM FIXTURE THICKNESS ACCOMMODATES SHEETS METAL SCREW SIZE BOX QTY CASE QTY BULK QTY 6411L 6400L S Mini Twist-N-Lock Nylon 3/4" # , M 6400M E-Z Mini Zinc 3/4" #6, #7, # B E-Z Ancor Zinc 3/4" #6, #7, # , EZ Stud Solver Zinc 3/4" # P 6400P B E-Z Twist N Lock Nylon 3/4" # , B - E-Z Toggle Zinc 1/2" # B Available in Bulk Pack Qty E-Z Mini E-Z E-Z E-Z Mini Twist-N-Lock Ancor Twist-N-Lock Toggle B 35

36 Rock-On Backer-On Fasteners Cement Board and Fiber Cement Backerboard Fasteners DESCRIPTION/ADVANTAGES Cement Board Applications ROCK-ON Rib design under head countersinks into dense material while preventing stripouts. Two point types for steel and wood applications. Larger head diameter increases board surface contact for greater pullover resistance. Rock-On is recommended for ACQ treated wood. SPECIFICATIONS ROCK-ON Diameter #9 Thread Form Drill Point Head Style Finish 9-15 Hi-Lo #9 Type S Wafer Head with countersinking ribs Climacoat BACKER-ON Gimlet points starts easily - no predrilling. Serrated thread design provides reduced installation torque and superior holding power. Rib design under head countersinks into dense material while preventing stripouts. #2 square drive prevents bit from slipping. BACKER-ON Diameter #10 Thread Form Drill Point Head Style Finish Serrated Gimlet Wafer Head with countersinking ribs Long life epoxy topcoat/zinc plating. INSTALLATION INSTRUCTIONS 1. A standard screwgun with a depth sensitive nosepiece should be used to install cement board fasteners. For optimal fastener performance, the screwgun should be a minimum of 6 amps and have an RPM range of Adjust the screwgun nosepiece to properly seat the fastener. 3. Worn or damaged bit tips should be replaced. 4. The fastener is fully seated when the head is flush with the work surface. 5. Overdrivng may result in torsional failure of the fastener or stripout of the substrate. 6. The fastener must penetrate beyond the metal structure a minimum of 3 pitches of thread. Cement-type boards or any dense sheathings to steel or wood studs. Wire lath to steel or wood studs. Plywood to steel or wood studs. Hardie Fiber Cement Backerboard B 36

37 Rock-On, Backer-On Fasteners SELECTION CHART Hi-Lo Rock-On Fasteners PART REFERENCE DESCRIPTION HEAD STYLE BX x 1-1/4" #2 PW BX x 1-5/8" #2 PW MATERIAL ATTACHMENT RANGE BOX QTY Up to 3/4" Material Thickness to Wood 3/8"-1" Material Thickness to Steel Up to 1-1/8" Material Thickness to Wood 3/8"-1-3/8" Material Thickness to Steel Cement Board to wood or light gauge steel gauge Backer-On Fasteners PART REFERENCE DESCRIPTION HEAD STYLE BX23206 BX23206 #10 x 1-1/4" #2 SW BX23137 BX23137 #10 x 1-1/4" #2 SW MATERIAL ATTACHMENT RANGE BOX QTY Up to 1/2" Backer Board to Wood Up to 1" Backer Board to Steel Up to 1/2" Backer Board to Wood Up to 1" Backer Board to Steel Backer Board to wood and steel PERFORMANCE TABLES Sheet Steel Gauges GAUGE NO Nominal Decimal Equivalent (Inch) Pullout Values FASTENER STEEL GAUGE (Lbs.) Hi-Lo Backer-On Wood Embedment #2 SPF 2 x 4 1/2" 3/4" 1" 1-1/4" Hi-Lo Backer-On The values listed are ultimate averages achieved under laboratory conditions and apply to Buildex manufactured fasteners only. Appropriate safety factors should be applied to these values for design purposes. B 37

38 Gridmate BR DESCRIPTION/ADVANTAGES Fastening Insulation To Concrete Textured head allows for coverage of stucco. Fins provided high holding power. Non cold-conductive. Non Corrosive. Made from strong Polypropylene. Easy to install. Plastic Insulation Fasteners All Polymer Modified (PM) Systems. Modified Stucco Systems. Exapnded lath over EPS, XPS or ISO rigid insulation. Fiberglass fabric over rigid insulation. Wire mesh over rigid insulation. Attaching rigid insulation to masonry or concrete. SELECTION CHART Gridmate BR Anchor PART REFERENCE DESCRIPTION HOLE DIAMETER MAXIMUM GRIP BOX QTY /4" 5/16" 1-1/2" /2" 5/16" 2-1/2" /8" 5/16" 3-1/4" /4" 5/16" 4" 100 Washer diameter is 1-3/8" PERFORMANCE TABLE Gridmate BR BASE MATERIAL EMBEDMENT ULTIMATE PULLOUT 25 MPA Concrete 1-1/8" 113 lbs. Concrete Block 1-1/8" 113 lbs. Brick 1-1/8" 113 lbs. 8 fasteners per 4' x 8' sheet required. B 38

39 Notes B 39