10 Ft. x10 Ft. Hard Top Garden House

Transcription

1 ongratulations on your STLK purchase. Smart style, long-lasting durability and unsurpassed value, that s what you get with STLK. omfort for home and outdoors, since 977, backed by the strongest satisfaction guarantee in the business. 0 t. x0 t. ard Top arden ouse tem # or assistance with your STLK product, please contact acific asual customer service at :30 am - :30 pm ST on-ri or at: ustomerservice@acificasual.com (ef # : 5SZ03-2T)

2 Table of ontents Table of ontents...2 Safety nformation...2 are nstructions...2 re-ssembly...3 lanning ssembly...3 art List...3 ssembly... Safety nformation W: Keep all flames and heat sources away from the roof boards and netting panels. These parts are not fire proof and will burn or melt if left in continuous contact with any extreme heat source. W: When assembling and using this product, basic safety precautions must alawys be followed to reduce the risk of personal injury and damage to product or surroundings. o not cook or barbeque under the roof. W: This garden house is T a permanent structure and is designed for sunshade and privacy only. The garden house should only be used in ideal weather conditions. ou UST completely disassemble the garden house prior to any extreme weather such as heavy thunder storms, hurricanes and/or ice/hail storms. ailure to do so may result in structural or property damage. UT: lways install the garden house on level ground utilizing the ground stakes provided for stability. t is not recommended to permanently anchor this garden house to a hard surface such as a wood deck or concrete floor. UT: arden house roof is weather resistant but may leak during precipitation. t is recommended to remove the roof boards if expecting ice or hail storms. UT: Keep all children and pets away from assembly area. egin assembly not less than 6 feet from any obstruction such as fence, garage, house, overhanging branches, clothes line or electrical wires. Some parts may contain sharp edges, wear protective gloves if necessary. are nstructions efore using, wipe with a clean, dry cloth. o not use bleach or solvents. Treat the frame with liquid wax for maximum protection against UV light and salty, damp air. lean the roof panels periodically with a mild soap and water. o not use harsh chemical cleaners as this will damage the panel finish. lease properly tighten all hardware and perform periodic inspections during usage for cracked welds or loose nuts or bolts. 2

3 re-ssembly L SSL t will take at least two people about 0 minutes to complete the assembly process. rubber mallet and a free standing ladder are needed during the process. T LST T: arts not shown to actual size. L K S art escription uantity K ight cross beam Left cross beam orner post orner roof tube oof sheet rail oof sheet rail oof sheet rail oof sheet rail oof rim oof tube etting rail 20 6 art escription uantity L S U-shaped connector Support arm oof sheet oof sheet oof sheet oof sheet oof sheet etting panel mportant: o not remove the protective film from the roof sheets until you are ready to attach them to the frame in Step 9. 3

4 re-ssembly T: ardware not shown to actual size. U V W Z art escription uantity U V W Z oof hub oof hub cover ook Washer plate Washer plate U-bracket nd cover nd cover 6 6 6x5 6x30+ut art escription uantity olt (6x5) olt (6x30) and nut 6 20 Self-tapping screw 32 round stake Wrench Wrench hilips screw driver

5 ssembly ttaching netting rails 32 K ttach one netting rail (K) to each cross beam ()/() with four self-tapping screws () using hilips screw driver (). 2 ssembling cross beams Z 6x Z L / L lug U-shaped connector (L) into each cross beam (), using bolts () loosely secure them together until the end of this step. epeat this for cross beam () until complete cross beams ( & ) are formed. ully tighten all the bolts (). ttach two U-brackets (Z) to the top of each cross beam ( /) with bolts () using wrench (). 5

6 ssembly 3. recting the main frame 6 6x5 K Stand the corner posts () up. ttach the side of the cross beam to the outside right corner of each corner post () and attach the side of the cross beam to the outside left corner of each corner post () with bolts () using wrench ().. ttaching support arms 6 6x5 djust corner posts () upright. ttach support arms () to cross beams ()/() and corner posts () with bolts () using wrench (). 6

7 ssembly 5. ssembling the roof frame U click! U Snap one corner roof tube () into each receiver of the roof hub (U) until you hear a click. 6. ttaching the roof frame V 6x30+ut W U With the ladder in the center of the main frame. lace the roof frame onto the top of the main frame. V ttach each roof tube () onto the bracket at the top of each corner post () with bolts and nuts () using wrenches () and (). ut the cover (V) on the top of the roof hub (U), screw the hook (W) into the bottom of the roof hub (U) until it secures the cover (V) firmly. 7

8 ssembly 7 ttaching roof sheet rails (,,,) 6x x30+ut ig. 7.2 ig. 7. ttach roof sheet rails () and () onto corner roof tube () with washer plates () and bolts () using wrench (). (ig.7.) o not fully tighten bolts until the end of step 0. ttach roof sheet rails () and () onto the brackets on top of cross beams () and () respectively with bolts and nuts () using wrench () and (). (ig.7.2) ollow the above proceedure to attach the roof sheet rails () and () onto the frame.

9 ssembly ttaching roof tubes () from underneath 6x5 ig.. ig..2 ig..3 / ig.. ig..5 / ig..6 rom the upper part of each corner roof tube () hook one end of roof tube () onto the small peg on washer plate (). (ig..) Secure the other end of roof tube () onto the small peg on the opposite washer plate (). epeat this until a x sqaure is formed. (ig..2 ) Loosely secure one washer plate () on each roof sheet rail () / () with bolts (). (ig..3) etween washer plates ( & ), ( & ) and ( & ), attach one roof tube () onto the small pegs of each pair of washer plates. (ig.. & ig.5) ake sure the three roof tubes () on the same side of the roof frame are in the same line. ully tighten all the bolts (). epeat this until a 3x3 sqaure is formed. (ig..6) 9

10 ssembly 9 nstalling roof sheets mportant: o not remove the protective film from the roof sheets until you are ready to attach them to the frame. uring assembly remove the protective film from each roof sheet as you attach them to the frame. Slide each roof sheet () into the rails (/) at until they fit securely at the top of the frame. Slide each roof sheet (/) into the rails (/) until they fit securely at the top of the rails. Slide each roof sheet (/) in the rails () and roof tube () until they fit securely at the top of the rails. ouble check to make sure all roof sheets are secured into each rail evenly without gaps. 0 ttaching roof rims t the bottom of each roof sheet on all four sides of the frame place the roof rims () onto the roof sheets tightly. 0

11 ssembly ttaching end covers and staking the gazebo 20 6x5 6 t the end of each corner roof tube (), cover the adjacent ends of each two roof rim with one end cover () and one bolt () using wrench (). t each side of the frame cover the remaining adjacent ends of each two roof rims with one end cover () and one bolt () using wrench (). ully tighten all bolts (/) to ensure the frame parts are secure. djust each corner post () to upright position. Stake two ground stakes () through the holes on post bases into soft ground. 2 anging netting panels K S ang each netting panel (S) onto the hooks on netting rails (K) in each corner of the garden house. Tie each netting panel to one corner post with hook and loop straps. lose the netting panels by sliding up the zippers to keep insects out. r undo the zipper and collect all netting around corner posts with ties for a clean look.