For assistance with assembly, please contact Customer Care Center

Transcription

1 TM NM: elham Living Steel Pergola azebo with Retractable anopy Shades SKU: P02- or assistance with assembly, please contact ustomer are enter /0

2 Note: t is very important to read and follow these Safety Precautions before assembly and during the use of this product. PR-SSMLY PRPRTON:! TS PK MY ONTN SMLL TMS W SOUL KPT WY ROM LRN Please check that all parts and hardware are included before beginning assembly. Save all packing materials until assembly is complete to avoid accidentally discarding smaller parts or hardware. Read through the preparation and assembly instructions in full before beginning assembly to reduce the risk of personal injury and damage to product or surroundings. Please use UTON N R WN LTN the product to avoid personal injury and (or) damage to the product. lways install on level ground utilizing ground stakes. This garden house cannot be permanently staked or attached to concrete floor or platform. Keep all children and pets away from assembly area. egin assembly not less than 6 feet from any obstruction such as fence, garage, house, overhanging branches, clothes line or electrical wires. Some parts may contain sharp edges, wear protective gloves if necessary. t least two or more people are recommended for safe assembly. Please have a ladder and a rubber mallet ready before assembly. 2/0

3 MNTNN N R TPS OR PROL ) Keep all flame and heat sources away from this tent fabric. This tent is made with fabric that meets P-84 specifications for the flame resistance. t is not fire proof. The fabric will burn if left in continuous contact with any flame source. The application of any foreign substance to the tent fabric may render the flame-resistance properties ineffective. 2) When assembling and using this product, basic safety precautions must always be followed to reduce the risk of personal injury and damage to product or surroundings. o not cook or barbeque under the canopy. 3) Notice: This gazebo / pergola is intended as a temporary shade structure, not a permanent structure. s a result the canopy / top must be removed during heavy rain, winds, or inclement weather including but not limited to thunderstorms, hurricanes, snow, and sleet. ailure to do so will risk damage to the canopy / top and the structure of the unit itself. amage occurred to the unit from not removing the top is not covered by the manufacturer. 4) arden house fabrics are water resistant but no waterproof and may leak during precipitation. abrics will fade from direct exposure to sunlight. 5) Please properly tighten all hardware and perform periodic inspections during usage for cracked welds or loose nuts or bolts. 3/0

4 Part list orner Post orner Post 6 Short Side eam Short Side eam M6 Long Side eam Long Side eam 2-M6 M6 4pcs Short eam pc Short eam 5pcs Short eam 6pcs uide Pole K uide Pole L uide Pole To best protect frame finish, do not put parts directly on ground. M Post ase 4pcs N Post Top over 4pcs racket racket O P pc S6 /0 4 Q anopy Stake ex Wrench ex Wrench R 8pcs S pc T pc olt ( M6x6 ) olt ( M6x55) olt M6x65) olt ( M6x5) 67pcs 2 0pcs 3 6pcs 4 6pcs olt ap 5 83pcs 3/9

5 T Step : ttaching post bases or or M M 4pcs M6x6 8pcs M ttach one post base (M) to the bottom of each corner post () with bolts () using hex wrench (T). ttach one post base (M) to the bottom of each corner post () with bolts () using hex wrench (T). 5 /0

6 Step 2: ttaching long side beams O N N N 4pcs 4 O M6x6 24pcs N 4 M6x5 8pcs S6 S T 6 /0 2. nsert beam () into beam (), secure the bracket (O) to beam () with bolts (). 2.2 nset the post top cover (N) into the top of post (,), make sure holes line up. 2.3 ttach one post () to each beam () with bolts (4) and bolts (). 2.4 ttach one post () to each beam () with bolts (4) and bolts ().

7 Step 3: ttaching short side beams M6x6 24pcs 4 M6x5 4 8pcs S6 S T 3. nsert one beam () into each beam () and secure them with bolts (). 3.2 ttach the beam () to the top of post () with bolts (4) and (). 3.3 ttach the beam () to the top of post () with bolts (4) and (). /0 7

8 2-M6 Step 4: ttaching short beams 4pcs M6 P pc P 5pcs 2 P pc M6x6 x P 2 M6x55 0x T 8/ nsert each beam () into one beam () and secure them with bolts (). 4.2 nsert beam () into beam () and attach bracket (P) to them with bolts (). 4.3 ttach the beams (- ) onto the center of the beams (-) with bolts (2). Note the bracket (P) shall stay underneath the beams (-). 4.4 ttach the beams (-) evenly onto the top of the beams (-) with bolts (2).

9 Step 5: ttaching guide poles 5 6pcs 3 3 6pcs M6x65 O T 5 83pcs 5 3 P 5 5. Snap guide poles () onto each bracket (O). 5.2 ttach the other end of the guide poles () to the beams (-) with bolts (3). 5.3 Snap guide poles () onto bracket (P). 5.4 ttach the other end of the guide poles () to the beams (-) with bolts (3). 5.5 ully tighten all the bolts (,2,3,4). over bolts (,2,3) with bolt caps (5). 9/0 /0

10 Step 6: ttaching canopies Q K 6.2 Q L L K Q 6. Q Q L R 8pcs K L R R 6.3 M 6. Pull canopies onto the guide poles under the short side beams. e sure each canopy lines up with the other at each long side of the frame. 6.2 nsert one guide pole (K) into both ends of one canop y. nsert one guide pole (L) into both ends of the other canopy. Snap each guide pole (L) into each guide pole (K). 0/0 /0 6.3 djust the position of each post (/) to make sure they stand upright. ammer ground stakes into soft ground through the holes on each post base to stabilize the pergola.