ASSEMBLY INSTRUCTIONS

Transcription

1 ASSEMBLY INSTRUCTIONS ATTENTION: THIS PRODUCT IS NOT FOR COMMERCIAL USE INTENDED FOR RESIDENTIAL USE ONLY. RUSF-WM Use the correct bolts as indicated. Do not tighten any of the bolts until is completely assembled. Do not discard of any of the packaging until you have checked that you have all of the parts and fittings required. Keep children away during assembly. This item contains small parts that can be swallowed by children. Children should always be under direct adult supervision while using this product. Retain these assembly instructions for future reference. Quote the following FQC NO. when contacting the service center. SERVICE CENTER TOLL FREE NO. TEL: FAX: PAGE OF COURTYARD CREATIONS INC.

2 A. Read instructions thoroughly. Acquaint yourself with the inventory of parts and the accompanying drawings to ensure safe and proper assembly. B. You will need the following tools: - Phillips Screwdriver (Not Included) - Nut Wrench (See Part #7) - Hex. Key Wrench (See Part #) C. Lay out all parts on a flat surface and identify them using the table below. PARTS LIST PART NO. MATERIAL CODE PART Q TY PART NO. MATERIAL CODE PART Q TY RUSF-CS0 TOP CROSS BEAM W/ADJUSTABLE TEETH 5 7C0A0707Y BOLT M*5 RUSFN0 7C0A0700Y FRONT UPRIGHT SUPPORT BOLT M*0 RUSFN0 7 7C0A0700Y REAR UPRIGHT SUPPORT BOLT M*5 RUSFQ0 7C7A000Y LATERAL CROSS BRACE SCREW ST.* 5 RUSFH0 9 7FA Y REAR CROSS BRACE WASHER d.5*d*. RUSF-CS0 0 7XA90 SWING ARM STEEL WASHER 7 RUSF-CS0 SEAT ASSEMBLY 000C00 PLASTIC NUT M*P.0 RUSFM SWING ARM TUBE BOLT CAP M FRONT LEG CAP BOLT CAP M REAR LEG CAP CANOPY/FRAME CONNECTOR 7GA000 5 RUSF-CS0 SUSPENSION SPRING PLASTIC SCREW 7C0A07907Y 7KAA00----Y BOLT M*55 HEX.KEY WRENCH MM 7C0A07000Y 7 7KAB0----Y BOLT M* NUT WRENCH 0&MM 7C0A0709Y RUSF-CS05 BOLT M*0 CANOPY PAGE OF

3 ASSEMBLY (Note: For all nuts and bolts fastening, always use a washer (#9 or #0) between the tube and bolt or the tube and nut.) Step A Step A - : Insert into the top cross beam w/adjustable teeth (#) upright supports (# and #), fasten them by using bolts (#), washers (#9) and plastic nuts (#). Keep the bolts loose. Do the same procedure for both sides. Do not tighten the bolts after Step A -. Fasten all bolts after Fig A. 9 9 Step A - Step A - : Fasten the lateral cross brace (#) to the upright supports (# and #) by using bolts (#) and washers (#9). Do the same procedure for both sides. 9 9 Step A - : Fasten the rear cross brace (#5) to the rear upright supports (#) by using bolts (#), washers (#9) and plastic nuts (#). Tighten all of the plastic nuts and bolts. Step A Step A - : Insert the front leg caps (#9) and rear leg caps (#0) into all of the base feet. Step A Fig. A 9 PAGE OF

4 Step B: Insert the front of the seat assembly (#7) into the swing arm (#). Fasten them together by using bolt (#7) and steel washer (#0). Open the seat assembly (#7) and fasten a swing arm tube (#) and a swing arm (#) to the seat assembly (#7) by using bolt (#5) and washers (#9), and plastic nut (#). Do the same procedure for both sides. Fasten another swing arm tube (#) to the swing arm (#) at the front bend by using bolts (#), washers (#9), and plastic nut (#). Do the same procedure for both sides Fig. B 0 7 Step C: Hook the suspension springs (#) into the top of both swing arm tubes (#). Do the same procedure for both sides. 7 Fig. C Step D: Hang the other side of the suspension springs (#) into the hole located on the angled brace on the top cross beam w/adjustable teeth (#). Do the same procedure for both sides. Warning: Make sure that both ends of the suspension springs (#) go completely through the holes in the angled braces on the top cross beam w/adjustable teeth (#) and the swing arm tubes (#). Fig. D PAGE OF

5 Step & Step : Slide the canopy/frame connectors (#) into the canopy (#). Fasten them together by using screws (#) in the pre-drilled holes. Make sure that the teeth of the canopy/frame connectors are facing toward the inside of the frame. Step Step Fig. E Step F: Fasten the canopy/frame connectors (#) to the adjustable teeth on the top cross beam w/adjustable teeth (#) by using a plastic screws (#5). 5 5 Fig. F Step G: To assure stability, double check that all of the bolts have been completely tightened and cover them with bolt caps (# and #). Warning: To avoid danger of suffocation, always keep plastic bags or small parts away from babies and children. Fig. G PAGE 5 OF

6 Cleaning and Maintenance Wash frame parts and fabric with mild soap and water, rinse thoroughly. Dry frame completely and allow the fabric to drip dry. Do not use bleach, acid, or other solvents on the fabric or frame parts. In order to prolong the life and beauty of your swing, we recommend that the swing be stored in a dry area when not in use. (For example, overnight or on rainy days) Inspect and tighten all bolts and fasteners on a regular basis to ensure proper performance and safety of your swing. Special Warnings. The user of this swing should always inspect it before each use.. It is essential to place this swing on level ground and not less than feet from any obstruction; such as fences, garages, houses, overhanging branches,laundry lines, or electrical wires.. Check the tightness of all of the nuts and bolts on a regular basis.. Make sure that the suspension springs are properly secured before each use. 5. Always remove the canopy in heavy wind conditions; otherwise the canopy may tip over and cause damage to its parts.. The manufacturer will not accept responsibility for unauthorized repairs or modifications to the swing or its parts. 7. Oil all of the metal parts that move regularly.. Weight limit is 500 lbs. Missing A Part? No Need To Go Back To The Store The store where you made your purchase does not stock parts for this item. If you need parts, whether they are missing or damaged, Call Toll Free: TEL: FAX: Call us between 9:00 AM and :0 PM Eastern Time Monday through Friday READ THESE INSTRUCTIONS COMPLETELY BEFORE STARTING ASSEMBLY SEPARATE AND IDENTIFY ALL PARTS, MAKING SURE THAT YOU HAVE ALL OF THE PARTS LISTED. IF YOU DO NOT LOCATE ALL OF THE PARTS LISTED, INSPECT THE PACKING MATERIAL FOR SMALL PARTS THAT MAY HAVE BECOME SEPARATED DURING SHIPMENT. IF YOU EXPERIENCE ANY DIFFICULTY DURING ASSEMBLY OR IF ANY PARTS ARE MISSING OR DAMAGED, CALL THE HELP LINE AT BEFORE RETURNING THIS ITEM TO THE STORE. PROVIDE THE FOLLOWING INFORMATION WHEN CALLING: -MODEL NUMBER OF THE PRODUCT. -PART NUMBER AND MATERIAL CODE OF THE PART FROM THE PARTS LIST. MOST PROBLEMS CAN BE RESOLVED WITHOUT RETURNING THIS PRODUCT TO THE RETAILER. PAGE OF