ASSEMBLY INSTRUCTION SHEET

Transcription

1 ASSMLY NSTRUTON ST TM# P SU# DSRPTON: RAND WT RPLA USTOMR SRV NO.:

2 ! Warning: 1. Need at least two adults to assemble this fireplace. 2. Assemble on soft, smooth surface to protect finish from being scratched. 3. DO NOT use power tools. 4. Remove all packaging material, make sure all parts are present before assembly. 5. stimated Assembly Time: 30 minutes. xact assembly times will vary based on skill level and past assembly experience. A PARTS LST TOP D AS ustomer Service or the missing or replacement of wooden panels, hardware, or electric fireplace insert, please contact Vendor ustomer Service at Working hour: Mon.-ri., 8:30am - 5:30pm Pacific Standard Time. RONT PANL TOP RAL AR NSTRUTONS: 1. lean periodically by wiping the product with a soft clean cloth. 2. Do not expose your product to any liquids. All liquids should be wiped up immediately with a soft, slightly damp cloth in the direction of wood grain. 3. Do not expose your product to strong or direct sunlight, near heat outlets or air conditioning units, open windows or dampness. xcessive exposure to sunlight and heat can cause fading of your furniture finish. xtreme temperatures and humidity changes can cause wood cracking and splitting. 4. lean using a glass/mirror cleaner and soft cloth. Do not use cleaning products containing abrasives, as these will scratch glass/mirror. LT SD PANL LT SD RAL RT SD PANL RT SD RAL LT POST SUPPORT 2pcs L RT POST SD TRM 2pcs

3 PARTS LST ASSMLY NSTRUTON M Step 1 Place Left side panel () face down on a smooth soft surface. (The side with the most holes should be facing up.) Align the holes of racket (8) with the holes of Left side panel () with the tenons facing outward as shown in figure 1. Secure the racket (8) to the Left side panel () with lat washer (), Spring washer (), and Short bolt (3) using Allen wrench (). DO NOT fully tighten bolts in this step for later LTR RPLA NSRT adjustment. Repeat this procedure to attach racket (8) to Right side panel () and ront panel () as shown in figure LON OLT 1/4*1-3/8" 23 pcs MDDL OLT 1/4*1-1/8" 8 pcs SORT OLT 1/4*5/8" 20 pcs 3 SPRN WASR 1/4" 51 pcs 8 7 LAT WASR ALLN WRN ROUND AD SRW 1/4"*16MM 4 MM #8*12MM 51 pcs 1 pc 6 pcs Tenons facing outside. 8 RAT 10 pcs 8 igure 1 8

4 ASSMLY NSTRUTON Step 2 Place Left post () on a soft smooth surface. With assistance from another adult, Slide Left side panel () into the groove of Left post () until both ends are flush. Secure the Left side panel () to Left post () with Long bolt (1), Spring washer (), lat washer () using Allen wrench () as shown in figure 2. DO NOT fully tighten the bolts in this step for later adjustment. Repeat this procedure to attach Right side panel () to Right post () as shown in figure 2. ASSMLY NSTRUTON Step 3 With assistance from another adult, insert the tenons of Left post () and Left side panel () into the corresponding holes of ase (). Panels may need to be slightly adjusted to be inserted into the proper holes. Secure Left Side panel to ase () with Short bolt (3), Spring washer (), lat washer () using Allen wrench () as shown in figure 3. DO NOT fully tighten bolts in this step for later adjustment. NOT: The Left side panel should be supported until secured in place to prevent the panels from tipping and causing damage or injury. Repeat this process for the Right post () and Right side panel (). 3 1 igure 2 igure 3

5 ASSMLY NSTRUTON Step 4 With assistance from another adult, Place Side trim (L) into the corresponding holes of Left side panel (). Side trim (L) should align with the trim on Left post(). Secure the trim in place with Long bolt (1), Spring washer (), lat washer () using Allen wrench () as shown in figure 4. DO NOT fully tighten bolts in this step for later adjustment. Repeat this process to attach the remaining Side trim (L) to the Right side panel (). ASSMLY NSTRUTON Step 5 nsert the tenons of Support () into the corresponding holes of ase (). Align the holes of Support () and Left post ().Secure Support () to Left post () with Middle bolt (2), Spring washer () and lat washer () using Allen wrench (). DO NOT fully tighten bolts in this step for later adjustment. Repeat this process to attach remaining Support () to Right post () as shown in figure 5. 1 L 2 L igure 4 igure 5

6 ASSMLY NSTRUTON Step 6 With assistance from another adult, place the ront panel () onto the tenons of Supports (). Secure the ront panel () to Left post () and Right post () with Middle bolt (2), Spring washer () and lat washer () using Allen wrench () as shown in figure 6. DO NOT fully tighten bolts at this time for later adjustment. ASSMLY NSTRUTON Step 7 With assistance from another adult, align the Left side rail () with the holes in Support () and ase (). The parts may need to be moved slightly to align the holes properly. Attach Left side rail () to Support () with Long bolt (1), Spring washer () and lat washer () using Allen wrench () as shown in figure 7. DO NOT fully tighten bolts at this time for later adjustment. Repeat this process to attach the Right side rail to the remaining Support () as shown in figure igure 6 igure 7 1

7 ASSMLY NSTRUTON Step 8 With assistance from another adult, Align the holes of Top rail (D) with the holes of ront panel (), Left side rail () and Right side rail (). Secure Top rail (D) to ront panel (), Left side rail () and Right side rail () using Long bolt (1), Spring washer () and lat washer () With Allen wrench () as shown in figure 8. DO NOT fully tighten bolts in this step for later adjustment. ASSMLY NSTRUTON Step 9 With assistance from another adult, align the tenons of Left side panel (), Left post (), ront panel (), Right post () and Right side panel () with the corresponding holes in Top (A) as shown in figure 9. Take care not to pinch your fingers as the top is lowered in place. Secure Top (A) to the Left side panel (), ront panel () and Right side panel () with Short bolt (3), Spring washer () and lat washer () using Allen wrench (). Adjust all parts to minimize any gaps between panels and ully tighten all bolts from Steps 1-9. D A D D 1 1 A 3 igure 8 igure 9

8 ASSMLY NSTRUTON Step 10 Place the lectric fireplace insert (M) into the assembled Mantel from the back. Slide the lectric fireplace insert (M) into the opening of the assembled Mantel and center so the space around the insert and rails is equal. Secure the lectric fireplace insert to the back of the assembled Mantel with Round head screws (7) using Phillips screwdriver (not provided) as shown in figure 10. ASSMLY NSTRUTON M 7 M Not provided Assembly is now complete. Note: Please read the operating manual for the lectric ireplace nsert and lectric ireplace nsert remote control before using ireplace. igure 10 PRNTD N NA MAD N NA