Made in / Hech en CHINA Distributed by Sears, Roebuck and Co., Hoffman Estates, IL 60179

Transcription

1 Owner s Manual Steel Round azebo Made in / Hech en HIN Distributed by Sears, Roebuck and o., Hoffman Estates, IL 079 See our extensive assortment of outdoor living products on-line at and Product ode: D7 M99 KSN: UP ode: Date of Purchase: / /

2 ssembly Instruction for Round azebo (FM00330F) ***UTION: The remote control is not water resistant! During severe or inclement (Rain, Snow, Wet...) weather, you must keep it indoors!

3 Part List Qty Image Description 5 eam eam with Screw Holder ambered Rail D Long Slide ar E Short Slide ar F Post Folding anopy H anopy over Support ar I 2 anopy over ttachment Tube J Solar Panel K eam Hub L Light over M Light N O Rail onnect Post Holder P ase Q anopy Handle R Netting S T anopy over Side Wall U Nut and Washer V 72 Plastic Ring

4 Part List Qty Image W 2 X Y Description Plastic Washer for Slide ars Screw & Nut Screw & Nut Screw Screw Screw Screw Nut Wrench 5 2 Magnetic Plate llen Wrench 7 Light ontrol with Holder 8 Slide ar Holder Plastic rove ountersunk Screw round Stake Wrench 2

5 Step Fig N O N Step:. Lay down all pcs ambered Rails () in a cycle. Insert all pcs Rail onnecters (N) into the end of ambered Rails (), keep screw holes straight, as shown in Fig. 2. Secure all pcs Post Holder (O) to the ambered Rails () with llen Wrench () and Mx5mm Screws (), as shown in Fig Turn over the circle structure as shown in Fig.3. DO NOT PUT NY WEIHT OR PRESSURE ON THE STRUTURE. 3

6 Step 2 Fig K K 3 O O 5 Fig 4 O Step2:. onnect all 5pcs of eams () and pc of eam with Screw Holder () to eam Hub (K). Use pc Mx5 Screw () to secure each beam to eam Hub (K), as shown in Fig. & Fig.2 2. This step requires 2 people to lift the Roof structure onto the circle structure. Have one hold the roof structure and the other person attach the bottoms of eams () and eam with Screw Holder () to the top of Post Holder (O), using Mx45 Screw (). Refer to Fig.3 3. onnect Magnetic Plate (5) with the inner part of ambered Rail () right below the eam with Screw Holder () using Mx8 Screws (3). Refer to Fig.4 4

7 Step 3 Fig 4 Fig 5 K K 4 U Fig 2 Fig X Step3:. Insert the bottom rib (the one without wheel) of the anopy () into the bottom of eam with Screw Holder (), as shown in Fig. onnect the top rib of the anopy () onto the top of eam with Screw Holder () with M5x5 Screw and Nut (X), as shown in Fig.2 2. Place the ribs with wheels onto the ambered Rail (), as Shown in Fig.3 & Fig.4. (Make sure all the wheels are on the back side of the magnetic plate (5). 3. Thread the wire of the anopy () through the top of the eam Hub (K). s shown in Fig.5. Secure the anopy () and eam Hub (K) with a Nut and Washer (U), using Nut Wrench () on the top of the eam Hub (K) and Wrench (2) under the anopy (). Tighten them as shown in Fig. 5

8 Step 4 Fig K M M Step4:. With one person holding the Light (M), another person connect the two wires as shown in Fig. 2. Secure the Light (M) under the Folding anopy () by inserting 2pcs Mx5 Screws() through the bracket and into the top of the Light(M). s shown in Fig.2

9 Step 5 I Fig I I S S H Fig 4 I I Step5:. Insert the 2pcs anopy over ttachment Tube (I) into anopy over (S) as shown in Fig.. ttach the anopy over (S) to the eams ( & ) with 3pcs Mx5 Screws () on each eam. s shown in Fig.3 & Fig.4 2. onnect the anopy over Support ar (H) onto the end of eam () and eam () with Mx5 Screw (). ttach the end of anopy over (S) to the anopy over Support ar (H) using the veko on the bottom of the anopy over (S). s shown in Fig.2 7

10 Step J L J Fig 4 L K M J Fig L Step: *** Take out Solar Panel (J), e sure to turn on the Solar Panel (J) (Press the red button), as shown in Fig.. Thread the wire on the Solar Panel (J) into the big hole of the Light over (L). onnect the Solar Panel (J) and Light over (L) with pc Mx5 (). s shown in Fig.2 2. onnect the wire on the Solar Panel (J) and the wire on the Light (M) in the eam Hub (K). s shown in Fig.3 3. Lay the Solar Panel (J) and Light over (L) onto the top of eam Hub (K). Keep the screw holes straight and secure the Light over (L) onto the beams with 2pcs Mx5 Screws (). s shown in Fig.4 *** Once the Solar Panel (J) and Light (M) is connected, you can try the remote control. If the light turns on, then it works. Otherwise, please check the wiring and make sure the Solar Panel (J) is turned "on". 8

11 Step 7 Y Fig Q P F 8 P F F 2 8 Step7:. ttach the anopy Handle (Q) onto the first outer rib on the front of Folding anopy () with M5x25 Screw and Nut (Y). Make sure the magnet on the handle can be adhered onto the rail. Refer to Fig. 2. Lay down the Post (F), and insert it into the ase (P). lign the screw holes and secure the ase (P) and Post (F) with Mx5 Screw (). Do the same for the other 5pcs Posts. Refer to Fig.2 3. ttach the Slide ar Holder (8) to the top of all pcs Posts (F) with Mx8 Screw (2). Refer to Fig.3 9

12 Step 8 Fig O F F 0 7 F Step8: 9 *** This step requires people and step ladders. Put Posts (F) vertically and close to the Post Holder (O) on the roof structure. have person lift the roof onto the Post (). djust the Post's position to ensure the screw holes are in line with Post Holder (F). 2. Secure the Posts (F) to Post Holder (O) with 5pcs Mx5 Screws () on each Post (F). Refer to Fig. lso tighten the screws on the ambered Rail () one more time in case the screw in the connection part loosen during moving and assembling. 3. Insert Plastic roves (9) into the holes on the Post (F) ( the one has 2 extra screw holes ) as shown in Fig.2; Install the Light ontrol Holder (7) on the Post (F). Push the ountersunk Screw (0) through the Light ontrol Holder (7) and into the Post (F). Refer to Fig.3 0

13 Step 9 D E E D D E 8 Fig 4 D E 2 D W Fig W E 2. Take out pc Short Slide ar (E) and pc Long Slide ar (D), connect the two slide bars with Mx8 Screw (2) in the middle of bars. Make sure there is a Plastic Washer (W) between two bars and a plastic Washer (W) between the Long Slide ar (D) and ambered Rail (). s shown in Fig. 2. Put the two ends of both Slide ar (D & E) into the Slide ar holder (8), as shown in Fig.3 & Fig.4. Tighten the Mx8 Screw (2) in the middle of slide bars to secure the slide bars to the ambered Rail (), as shown in Fig.2. Do the same for other 5 sets of slide bars.

14 Step 0 Fig V T D E V R T T R P F. Put the Plastic Rings (V) into the holes on the top of Sidewalls (T) and Nettings (R). Hang the Sidewall (T) onto the Long Slide ar (D) which is closer to the ambered Rail () as shown in Fig.. Hang the Netting onto Short Slide ar (E), as shown in Fig.2 2. Press down the round Stakes () through the ase (P) into the ground. Refer to Fig.3 2