Sonoma Hardtop Gazebo 10 X 12. Owner s Manual

Transcription

1 Sonoma Hardtop Gazebo 10 X 12 Owner s Manual Congratulations on your purchase of our Sonoma Hardtop Gazebo. Our clear, easy to follow, step-by-step instructions will guide you through the assembly process from start to finish. WARNING: THIS UNIT IS HEAVY! For safety, DO NOT assemble this item alone. Six to eight people are recommended for safe assembly. Keep all children and pets away from assembly area. Children and pets should be supervised when they are in the assembly area of the gazebo. Do not assemble less than 6 ft / 1.8 m from any obstruction such as a fence, garage, house, overhanging branches, laundry line or electrical wires. Some parts may contain sharp edges. Wear protective gloves. When assembling and using this product, basic safety precautions should always be followed to reduce the risk of personal injury and damage to equipment. Please read all instructions before assembly and usage. For outdoor use only. Install on level ground. Check all bolts for tightness before and during usage. IMPORTANT Please take time to read these instructions thoroughly and follow each step carefully for safe and easy operation. Keep this manual for future reference. We would like to hear from you with any comments or suggestions. In the continental U.S., you can call us toll-free at from 8 a.m. to 5 p.m. CST Monday Friday. You can also send us an using the feedback icon at SamsClub.com. Call centre for missing parts: from 8:00 a.m. EST to 8:00 p.m. PST.

2 Parts List Step 1 A1 (x2) Long Decorative Gutter B1 (x2) Short Decorative Gutter C1(X2) Corner Decorative Gutter 1 D1(x2) Corner Decorative Gutter 2 E1(x4) Middle Beam Connector F1(x8) Decorative Gutter Connector G1(X4) Corner Connector H1(x4) Long Mosquito Netting Tube I1(x4) Short Mosquito Netting Tube

3 Step 2 A2(x4) Top Slanting Bar B2 (x1) Big Top Frame C2 (x4) Middle Beam of Big Top D2 (x2) Left Long Support Beam of Big Top Long Side E2 (x2) Right Long Support Beam of Big Top Long Side F2 (x2) Left Short Support Beam of Big Top Long Side G2(x2) Right Short Support Beam of Big Top Long Side H2 (x2) Left Long Support Beam of Big Top Short Side I2 (x2) Right Long Support Beam of Big Top Short Side J2 (x2) Left Short Support Beam of Big Top Short Side Right Short Support K2 (x2) Beam of Big Top Short Side Step 3 A3 (X2) Small Top Bottom Beam 1 B3 (X4) Small Top Sheeting C3 (x2) Roof cover of small top long side D3 (x2) Roof Cover of Small Top Short Side E3 (x1) Small Top Bottom Connecting Frame F3 (X2) Small Top Bottom Beam 2 G3 (x1) Small Top Connector H3 (x1) Small Top Cover I3 (x1) Top Decor J3(x1) Chandelier Hook Step 4 A4(X4) Post Base B4 (x4) Base Cover C4 (x4) Post D4 (x4) Top Block E4(X4) Block Plate F4(X2) Short Right Arc Support G4(X2) Short Left Arc Support H4(X2) Long Right Arc Support I4(X2) Long Left Arc Support

4 Step 5 A5(x2) Left Long Big Top Cover B5 (x2) Right Long Big Top Cover C5 (x4) Left Middle Big Top Cover D5(x4) Right Middle Big Top Cover E5 (x4) Left Small Big Top Cover F5 (x4) Right Small Big Top Cover G5 (x2) Short Big Top Cover H5(X4) Top Cover I5(X18) Roof Press Sheet J5(x1) Mosquito Netting Hardware Pack 1 AA Plastic Cap 16 PCS M6 Flat Washer 64 PCS CC M6x15 Short Bolt 64 PCS JJ Hook 52 PCS LL M6 Wrench 2 PCS Fig.1-1: Connect Decorative Gutter Connectors (F1) with Corner Decorative Gutters1 (C1) and Corner Decorative Gutters 2 (D1) using Short Bolts (CC) and Flat Washers (). Tighten with Wrench (LL). Fig.1-2: Insert Long Decorative Gutters (A1) into Corner Decorative Gutters (C1& D1) using Short Bolts (CC) and Flat Washers (). Tighten with Wrench (LL). (Note: the Corner Decorative Gutters with A1 labels) Fig.1-3: Insert Short Decorative Gutters (B1) into Corner Decorative Gutters (C1& D1) using Short Bolts (CC) and Flat Washers (). Tighten with Wrench (LL). (Note: the Corner Decorative Gutter with B1 labels)

5 Fig. 2: Attach Middle Beam Connectors (E1) to Long Decorative Gutters (A1) and Short Decorative Gutters(B1) using Short Bolts (CC) and Flat Washers (). Tighten with Wrench (LL). Fig.3: Attach Corner Connectors (G1) to Corner Decorative Gutter 1 (C1&D1) using Short Bolts (CC) and Flat Washers (). Tighten with wrench (LL) Fig. 4: Attach plastic cap (AA) to the one end of Long Mosquito Netting Tube (H1), then insert 7 Hooks (JJ) into the inside rail of Long Mosquito Netting Tube (H1) as shown and 6 Hooks (JJ) into the inside rail of Short Mosquito Netting Tubes (I1) as shown. Attach plastic cap (AA) to the other end of netting tubes. Attach the one end of Long Mosquito Netting Tubes (H1) to Long Decorative Gutters (A1) and attach the other end one (H1) to Corner Decorative Gutters (C1&D1) using Short Bolts (CC) and Flat Washers (). Repeat this step for attaching the one end of Short Mosquito Netting Tubes (I1) to Short Decorative Gutters (B1) and attaching the other end of Short Mosquito Netting Tubes (I1) to Corner Decorative Gutters (C1&D1). Tighten with Wrench (LL). Hardware Pack 2 M6 Flat Washer 64 PCS CC M6x15 Short Bolt 16PCS DD M6x15 Short Screw 32 PCS EE M6x55 Long Screw 16 PCS FF M6 Nut 16 PCS

6 Fig.5: Fix the lower end of Top Slanting Bars (A2) onto the Corner Connectors (G1) using Long Screws (EE), Flat Washer () and Nuts (FF). Fig.6: Assemble the top end of Top Slanting Bars (A2) to Big Top Frames (B2) using Bolts (CC) and Flat Washers (). Tighten with Wrench (LL). Fig.7: Fix the lower end of Middle Beams (C2) onto the Big Top Frames (B2) using Bolts (CC) and Flat Washers (). Fig.8: Attach the lower end of Middle Beams (C2) to the lower end of Middle Beam Connectors (E1) using Short Bolts (CC) and Flat Washers (). Tighten with Wrench (LL). Fig.9: Attach one end of Left Long Support Beams of Big Top Long Side (D2) to Middle Beams (C2) using Short Screws (DD) and Flat Washers (). Tighten with Wrench (LL). Fig.10: Fix the other end of Left Long Support Beams of Big Top Long Side (D2) onto the Top Slanting Bars (A2) using Short Screws (DD) and Flat Washers (). Repeat steps 9-10 for remaining big top beams (E2, F2, G2, H2, J2, K2) Hardware Pack 3 M6 Flat Washer 20 PCS CC M6x15 Short Bolt 8PCS DD M6*15 Short Screw 8 PCS KK M6 Nut 4PCS

7 A3 E3 G3 Fig.11 F3 A3 Fig.12 Fig.11 KK A3(F3) Fig.12 CC A3(F3) G3 J3 E3 Fig.13-1 CC E3 CC Fig.14-1 DD DD B3 F3 B3 D3 A3 B2 C3 DD Fig.13-2 D3 B3 DD C3 Fig.14-2 D3 I3 H3 J3 Fig.11: Attach the top end of Small Top Bottom Beams 1 (A3) and Small Top Bottom Beams 2 (F3) to Small Top Connectors (G3) using Nuts (KK) and Flat Washers (). Screw the Chandelier Hook (J3) to Small Top Connector (G3). Fig.12: Attach the lower end of Small Top Bottom Beams 1 (A3) and Small Top Bottom Beams 2 (F3) to Small Top Bottom Connecting Frames (E3) using Short Bolt (CC) and Flat Washers (). Tighten with Wrench (LL). Fig.13-1: Attach assembled small top to Big Top Frames (B2) through Small Top Bottom Connecting Frames (E3) using Short Bolts (CC) and Flat Washers (). Tighten with Wrench (LL). Fig.13-2: Place roof covers of Small Top Long Side (C3) and roof covers of Small Top Short Side (D3) to small top. Fig.14-1: Attach Small Top Sheeting (B3) to Small Top Bottom Beams 1 (A3) and Small Top Bottom Beams 2 (F3) using Short Screws (DD) and Flat Washers (). Tighten with screwdriver. Fig.14-2: Place the Small Top Cover (H3) onto the small top and screw the Top Décor (I3) onto the exposed end of Chandelier Hook (J3). Hardware Pack 4 M6 Flat Washers 92PCS DD M6x15 Short Screw 24 PCS HH Ф8*260 Peg 16PCS II Ф6*80 Anchor 16PCS MM M6x20 Long Bolt 68PCS

8 Fig.15: Insert the Posts (C4) into the Base Covers (B4), then install the Post Bases (A4) to the bottom of Posts (C4) using Small Screws (DD) and Flat Washers (). Fig.16: Attach the Top Blocks (D4) to the top of Posts (C4) using Long Bolts (MM) and Flat Washers (). Tighten with Wrench (LL). (The screw holes on the posts and the screw holes on the block plates must align as shown in order to secure the connection properly.) Fig.17: Lift the assembled roof and attach the assembled post to the Corner Decorative Gutter 1 (C1) and Corner Decorative Gutter 2 (D1) using Long Bolts (MM) & Flat Washers (). Tighten with Wrench (LL). (Note: This unit is heavy. Six to eight people are recommended for this step for safe assembly.) Fig.18: Attach the Corner Connectors (G1) to the Top Blocks (D4) using Long Bolts (MM) and Flat Washers (). Tighten with Wrench (LL). Fig. 19: Attach the Block Plates (E4) to the Top Blocks (D4) using Small Screws (DD) and Flat Washers (). Tighten with Wrench (LL). Fig.20: Attach the Short Right Arc Supports (F4) to Decorative Gutters and the Posts (C4) using Long Bolts (MM) and Flat Washers (). Repeat this step for all other Arc Supports (G4 H4 I4). Fig.21: Fix the gazebo on the grass ground with the Pegs (HH). Fig.21: Fix the gazebo on the cement ground with the Anchors (II). Hardware Pack 5 M6 Flat Washer 68PCS DD M6x15 Short Screw 60PCS GG M6x40MiddleScrews 8PCS

9 Fig.22: Press Left Long Big Top Cover (A5) to Right Long Big Top Cover (B5) Fig.22-1: Insert the assemblies into the U groove of Big Top Frame (B2). Repeat the steps for Short Big Top Cover (G5). Fig.23: Attach Left Long Big Top Covers (A5) and Short Big Top Covers (G5) to Top Slanting Bars (A2) using Small Screws (DD) and Flat Washers (). Fig.24-1: Attach Right Middle Big Top Covers (D5) and Left Middle Big Top Covers (C5) to Top Slanting Bars (A2) using Small Screws (DD) and Flat Washers (). Tighten with screwdriver. Fig.24-2: Attach Right Small Big Top Covers (F5) and Left Small Big Top Covers (E5) to Top Slanting Bars (A2) using Small Screws (DD) and Flat Washers (). Tighten with screwdriver. Fig.25: Press up the roof covers with the Roof Press Sheet (I5) and attach the Roof Press Sheet (I5) to decorative beams using Small Screws (DD) and Flat Washers (). Tighten with screwdriver. Fig.26: Insert the Top Cover (H5) into each hole of Small Top Frame (B2). Fig.27: Attach the Top Cover (H5) on the Top Slanting Bar (A2) using Short Screws (DD) and Flat Washers ()

10 Fig.28: Hang the Mosquito Netting (J5) onto Long Mosquito Netting Tubes (H1) and Short Mosquito Netting Tubes (I1) by Hooks (JJ). Note: Please keep mosquito netting with pre-assembled belt outside. Be mindful of the dimensions of the item to ensure you install the Mosquito NCetting (J5) correctly. Attach 6 hooks to Short Tubes (I1) and 7 hooks to Long Tubes (H1). Now, your Sonoma Pavilion is ready for use. Back up hardware pack M6 Flat Washer 15 PCS CC M6x15 Short Bolts 10 PCS DD M6x15 Short Screws 8 PCS EE M6x55 Long Screw 1 PCS FF M6 Nut 1PCS GG M6x40 Middle Screws 1PCS JJ Hook 8PCS KK M6 Nut 1 PCS

11 IMPORTANT: 1. Keep all children and pets away from assembly area. Children and pets should be supervised when they are in theareaofpavilionconstruction. 2. The area for assembly should not be less than 6 feet from any obstruction such as fence, garage, house, overhanging branches, laundry line or electrical wires. 3. This unit is heavy. Do not assemble this item alone. Six people are recommended for safe assembly. 4. Some parts may contain sharp edges. Wear protective gloves if necessary during assembly. 5. When assembling and using this product, basic safety precautions should always be followed to reduce the risk of personal injury and damage to equipment. Please read all instructions before assembly and use. 6. For outdoor use only. Install on level ground. 16 stakes are provided to secure the pavilion in the ground. If you wish to secure the pavilion to a wood deck or concrete surface, you will need to purchase fasteners appropriate for these surfaces. These are readily available at your local hardware store or home center. 7. Check all bolts for tightness before and during usage. 8. Please check your state and local regulations prior to purchasing. Some jurisdictions may require permits for, or otherwise regulate, installation and use. 9. While this pavilion is manufactured to withstand gale force winds utilizing only the supplied ground stakes, in areas subject to frequent severe weather, securing the pavilion to a deck, concrete patio or footings should be considered. 10. Your pavilion has been engineered to accommodate winter snow loads incurred in most areas. Removal of accumulated snow on the pavilion roof with a roof rake is recommended. In areas that are regularly subject to blizzard conditions however, removal of the roof panel is suggested. The assembled roof structure can simply be left intact until warmer conditions return. CARE & Maintenance Our steel components for garden accessories and furniture are treated with rust inhibiting paint that protects it from rusting. However, due to the nature of steel, surface oxidation (rusting) will occur once these protective coatings are scratched. This is a natural process and is not a defect! To minimize this condition, we recommend care when assembling & handling the product to prevent scratching the paint. Should any scratching or damage occur, we recommend immediate touch-up with rust inhibiting paint. Surface rust can also be easily removed with a very light application of common cooking oil. If surface oxidation (rusting) occurs and if no measure is taken to prevent this, the oxidation may start dripping on to deck or patio and caused damaging stains, which may be difficult to remove. This can be prevented if the measure is taken to keep the product from oxidizing. Made in China