12' 12' Diamond Gazebo Assembly Instruction

Transcription

1 12' 12' Diamond Gazebo Assembly Instruction Model:Lichfield Item: ZYG11-7 IMPORTANT: Please read and follow all safety statements, warnings, assembly instructions, use & care directions before attempting to assemble. 1. When installing and assembling your gazebo, it is recommended that 2 or more adults are involved. 2. Do not use the unit during an electrical storm, as there is a remote chance of getting struck by lightening. 3. Do not climb on top of the gazebo. Falling off the gazebo can result in serious injury, possibly even death. 4. Do not leave the gazebo assembled when there is a risk of high wind, as possible damage will occur to the structure. 5. Never barbecue under this gazebo or use lanterns that contain naked flames. 6. This package contains small items and plastic bags that should be kept away from children. 7. Ensure that all connectors & poles are firmly secured in position fully. It is important to do so before use so as to avoid collapsing or damage to the item, which could result in injury. 8. WARNING: Please take down the gazebo during strong wind. The manufacturer or retailer is not liable for any loss of the product or other items due to the failure to take down the gazebo during strong wind. 1 of 9

2 Parts List Centre screen A1 4 Left screen B1 4 Right screen C1 4 beam A2 4 Centre connector A3 1 Arch bar connecter B3 4 top roof brace I3 4 Arch bar(corner) C3 8 Arch bar D3 4 Small top connector E3 1 pothook F3 1 Big canopy G3 1 Small canopy H3 1 F inial J3 1 Mosquito netting A4 1 stake DD 8 Mosquito hook EE 56 2 of 9

3 Hardware Pack 1 16 pieces (AA) M6 20 mm screw 16 pieces (CC) M6 mm washer 1 piece (W2) M6 Wrench Fig.1 CC AA CC AA B1 A1 C1 Insert the Right Screen (C1) into the Big Screen (A1), pull it down to fix them; Then Attached part C1 and part A1 with screw AA and washer CC, fully tighten. Repeat this procedure for B1 and A1. 3 of 9

4 Hardware Pack 2 16 pieces (BB) M6 15 mm screw 16pieces (CC) M6 mm washer A2 A2 BB Attach A2 to B1 using BB and CC. Repeat this procedure for A2 and C1. C1 B1 A1 C1 Fig.2 B1 Hardware Pack 3 4 pieces (BB) M6 15mm screw 4 pieces (CC) M6mm washer 4 of 9

5 Fig.3-1: Screw Center Hook (F3) into Centre fitting (A3) and secure them properly. Fig.3-2: Connect Slanting Bar (B3) with Centre fitting (A3). Fig.3-3&3-4: A ladder is needed for this step When placing Centre fitting (A3), Connect one end of Corner Arch bar1 (C3) and Slanting Bar (B3), an d fix the other end of C3 with Screen (A1). Fig.3-5& 3-6: Connect one end of Arch Bar 2 (D3) and Cent re Fitting (A3), and secure the other end of D3 to the Beam (A2) with Screw (BB) and Washer (CC). 5 of 9

6 G3 Fig.3-7: Place the large canopy (G3) over theassembled top frame. Do not cover fully. Fig.3-8: Insert Top roof brace (I3) into Small top connector (E3) Fig.3-9: Place the small canopy (H 3) onto the small top frame. Fig.3-10: Tighten the finial (J3) onto the bolt on the top. Fig.3-11: Fit the assembled small top frame onto the large top frame, and insert Top roof brace (I3) into Slanting Bar (B3). Fig.3-12: Fasten the ties on both small canopy (H3) and large canopy (G3). 6 of 9

7 Fig.13 Fig.3-13: Spread the large canopy (G3). Attach the hooks on the canopy to the ScreenBı 1, C1.ı The double roof is now fully assembled. 7 of 9

8 Fig.3-14 EE EE A4 Fig.3-14 Attach the mosquito netting to screen and beam by using EE. Fig.3-15 Anchor the screens to the ground by using stakes (DD). Fig.3-15 Extra parts 4 pieces Spring buckle 2 pieces (AA) M6 20mm screw 4 pieces (CC) M6mm washer 2 pieces (BB) M6 15mm screw 1 piece Touch-up paint 8 of 9

9 USE & CARE 1. This Gazebo is not a permanent structure and should be disassembled & stored away after use. 2. Do not repack your gazebo until completely dry. 3. This Gazebo must not be left erect in windy conditions. WARNINGS 1. Assembly Instructions must be followed. 2. Pegs and ropes supplied must be used to hold this gazebo in place when upright. 3. Warranty does not cover damage due to extreme weather conditions. CUSTOMER SERVICE Zenith Industries, LCC warrants to the original purchaser that this item is free from defects in workmanship and materials of your item provided the item was factory-sealed at the time of purchase and is maintained with care and used only for personal, residential purposes. The item is warranted to be free from defects in material or workmanship for a period of 6 months. Should any manufacturing defect arise within this warranty period, Zenith Industries will repair or replace (at our option) any defective merchandise upon proof of purchase; however, transportation and delivery costs, as well as labor and material charges to remove or replace parts, remain the responsibility of the purchaser. A purchaser of an "open box," previously-returned, or "clearance" item, as well as original purchasers outside of the warranty period, may obtain replacement parts from Zenith Industries for products in current production, at nominal cost. If you are within the return policy that most stores have, you do have the option of returning this item back to the store which you bought it from for an exchange of the same item, or a refund of the purchase. If you are within or beyond the return policy that most stores have, and need tech. assistance or replacement parts, please call Zenith Industries, LLC at 1( 513) from 8:30 am to 5:30 pm eastern standard time or to Service@zenithindllc.com or fax your parts replacement order form together with the purchase receipt to 1 ( 513) for assistance. 9 of 9