Tools for the toughest demands. Special accessories for routing. A handy guide

Transcription

1 Tools for the toughest demands Special accessories for routing A handy guide

2 The Festool router system This part of the router booklet provides information on Festool accessories for routers and edge routers. By using the products listed in this booklet, you can perform many applications in an assured and optimal manner. Power tools, routers and very helpful accessories everything that you need and all from a single source. By reading the information contained in this booklet, you will find out about all the Festool router bits that are available. Cutters for routing edges are listed for the power tools in this section. 2

3 OF 1010 router Super handy and powerful Always under control. Because of its compact shape and low weight, the OF 1010 router is easy to guide with just one hand. And it has the power to do the job. Ergonomic handle MMC electronics Optimal chip extraction Central column clamp Precise depth setting Technical specifications Power consumption Idle engine speed Rapid routing depth setting feature 1,010 W 10,000 24,000 rpm 55 mm Routing depth fine setting Router stroke Max. cutter Ø Dust extraction Ø Weight 8 mm 50 mm 50 mm 27 mm 2.7 kg (The side fence and the guide stop for the guide rail are included within the set and the plus versions.) 3

4 Clamping collets OF 1010 OFK 700 MFK 700 Clamping collets with retainer nuts* For cutter shank Ø 6.0 mm Ø 6.35 mm Ø 8.0 mm * Also for OF 900, OF

5 Base runners with large surfaces OF 1010 Base runner for trim finishing Item Base runner with centre hole Ø 15 mm Item Base runner with chip catcher Ø 48 mm Table extension* Item Table extension with centre hole Ø 15 mm * Also for OF 900, OF 1000, KF 4/5. 5

6 Copying rings OF 1010 Copying rings with fixing screw* Item D 10.8 mm, d 7.8 mm D 17.0 mm, d 14.0 mm D 24.0 mm, d 21.0 mm D 27.0 mm, d 24.0 mm D 30.0 mm, d 27.0 mm D 40.0 mm, d 37.0 mm * Also for OF 900, OF 1000, KF 4/5. Copying rings for use with the joining system Item D 8.5 mm, VS D 13.8 mm, VS D 17.0 mm, VS D 24.0 mm, VS

7 Router attachment for solid wood trim OF 1010 For routing solid wood trim up to 28 mm* Item The angle arm is needed if the edging plate or the copier scanning set is used Edging plate Angle arm and edging plate for flush trimming up to 28 mm solid wood trim Chip deflector suggested when flush trimming solid wood trim * Also for OF 900, OF 1000, KF 4/5. 7

8 Copier scanning set OF 1010 Copier scanning set and angle arm 1) Item Angle arm required in connection with the edging plate or the copier scanning set Copier scanning set 2) Even, curved workpieces or milling templates can be copied by using the copier scanning set and the angle arm ) Also for OF 900, OF 1000 and OF ) Items included: copier scanning rollers Ø 16 and Ø 20 mm, copier scanning pin. 8

9 OF 1400 router The all-around machine for many types of jobs A power tool concept that is setting standards. Whether it s the size, the weight, the handling or the performance all the details and functions are perfectly matched to each other in the OF Fast, easy changing of cutters Copying ring can be changed without tools Quick-acting brake and MMC electronics Dual column clamps Optimal chip extraction Technical specifications Power consumption Idle engine speed Rapid routing depth setting feature 1,400 W 10,000 22,500 rpm 70 mm Routing depth fine setting Router stroke Max. cutter Ø Dust extraction Ø Weight 8 mm 70 mm 63 mm 27/36 mm 4.5 kg (A side fence, 3 clamping collets (8 mm, 12 mm, 1/2") and a Ø 30 mm copying ring are included.) 9

10 Clamping collets OF 1400 OF 2200 Clamping collets with retainer nuts For cutter shank Ø 6.0 mm Ø 6.35 mm Ø 8.0 mm Ø 9.53 mm Ø 10.0 mm Ø 12.0 mm Ø 12.7 mm

11 Copying rings OF 1400 Copying rings* Item D 17.0 mm, d 14.0 mm D 24.0 mm, d 21.0 mm D 27.0 mm, d 24.0 mm D 30.0 mm, d 27.0 mm D 40.0 mm, d 37.0 mm * Can be changed without the use of tools. Copying rings for use with the VS 600 Item D 8.5 mm, VS D 13.8 mm, VS D 17.0 mm, VS D 24.0 mm, VS d D 11

12 Base runners large surfaces/guide system OF 1400 Base runner for trim finishing Item Hard fibre base runner Reduced 20 mm base runner hole, max. cutter diameter 37 mm Base runner with chip catcher and wider surface for secure routing and optimal dust extraction; router passage max. 63 mm Guide system Guide stop with fine settings and support for the router. (please order guide rods separately) Guide rods For use of side fence and the guide stop set, length 400 mm

13 OF 2200 router A masterpiece. The OF 2200 will impress you with its design, its powerful drive, its outstanding ergonomics and precision. And it s rated at an unbelievable 2,200 watts! Strong draw New ergonomic design Base runner replacement without tools Copying ring replacement without tools Double guide column clamping system Technical specifications Power consumption Idle engine speed Router stroke Max. cutter diameter Fine adjustment Dust extraction connection Ø Weight 2,200 W 10,000 22,000 rpm 80 mm 89 mm 1/10 mm 36 mm 7.8 kg (Includes chip catcher, 3 clamping collets (8 mm, 12 mm, 1/2") and Ø 30 mm copying ring.) 13

14 Clamping collets OF 1400 OF 2200 Clamping collets with retainer nuts For cutter shank Ø 6.0 mm Ø 6.35 mm Ø 8.0 mm Ø 9.53 mm Ø 10.0 mm Ø 12.0 mm Ø 12.7 mm

15 Copying rings OF 2200 Copying rings* Item D 17.0 mm, d 14.0 mm D 24.0 mm, d 21.0 mm D 27.0 mm, d 24.0 mm D 30.0 mm, d 27.0 mm D 40.0 mm, d 37.0 mm * Can be changed without the use of tools. d D 15

16 Base runner selection OF 2200 Accessories for base runners, in a Systainer Item Accessories Systainer ZS-OF 2200, metric units including 1x side fence SA-OF 2200, guide stop set FS-OF 2200, base runner LA-OF 2200 Ø 36 CT, base runner LA-OF 2200 Ø 36, base runner with wide support AFB-OF 2200, and Ø 17, 24, 27, 40 mm copying rings, in a SYS 2 SYSTAINER

17 Base runner for groove cutter OF 2200 Base runner Ø 36 CT* Item This base runner is specially designed for copying rings up to 30 mm in diameter, together with extraction ports for extracting chips from above; for secure and clean routing * Can be changed without the use of tools. 17

18 Base runner with wide support OF 2200 AFB-OF base runner* Item Provides increased safety because it reduces the risk of tipping over when routing around corners, and is ideal for safely guiding the OF 2200 on edges * Can be changed without the use of tools. 18

19 Base runner for edges OF 2200 Base runner Ø 36* Item For copying rings with diameters up to 30 mm; in particular, this base runner is perfectly suited for use on edges with small router bits. It helps prevent tipping when routing around corners * Can be replaced without the use of tools. Can also be milled out to accommodate larger router bits. 19

20 Side fence and guide stop OF 2200 Side fence and guide system Item Side fence For example, for rebating or grooving. With adjustable sliding plastic jaws, fine settings at a precision of 1/10 mm, and extractor hood. (please order guide rods separately) Guide stop set With 1/10 mm precision fine settings for the FS/2 guide rail. The base runner with height adjustment for the guide rail ensures that the router is securely positioned. (please order guide rods separately) Guide rods For use of side fence and the guide stop set, length 400 mm

21 Accessories for all Festool routers System accessories for fast and precise routing. 21 www. festool. c o m

22 Hole drilling system OF 1010 OF 1400 Systematic routing of rows of holes for small production runs 1) Item Hole drilling set Guide plate, centring mandrel, 2x side fence (please order the guide rail with the row of holes, clamps and dowel drill separately) Hole drilling set Complete range of items in a Systainer with a Ø 5 mm dowel drill and clamps (please order the guide rail with the row of holes separately) FS/2 guide rail with a row of holes Length 1,080 mm Length 2,424 mm Dowel drill 2) Ø 3 mm ) Ø 5 m Ø 6 mm Ø 8 mm Ø 10 mm Drill 3) Ø 5 m ) Also for the OF 900, OF ) More information is in the router section on Page 23. 3) Without centre point. 22

23 Dovetail joints 1 Basic module VS 600 OF 1010 OF 1400 VS 600 basic unit and router templates For making traditional dovetail joints with 7 different router templates: Partially covered dovetail joints Dovetail sizes 14 mm and 20 mm Open dovetail joints Dovetail sizes 14 mm and 20 mm Slot joints Slot sizes 6 mm and 10 mm Dowel joints 6 mm to 10 mm Item VS 600 basic unit The OF 900 and the OF 1000 can also be used for the joining system. 23

24 Dovetail joints 2 Templates OF 1010 OF 1400 Partially covered dovetail joints* Item Dovetail size 14 mm Workpiece thickness mm (Ø 17 mm copying ring for the OF 1010 included) Suitable cutters, 8 mm shank Dovetail cutter Ø 14.3 mm, 15 HS or Dovetail cutter Ø 14.3 mm, 15 HW Dovetail size 20 mm Workpiece thickness mm (Ø 24 mm copying ring for the OF 1010 included) Suitable cutters, 8 mm shank Dovetail cutter Ø 20 mm, 15 HS or Dovetail cutter Ø 20 mm, 15 HW * With special copying rings for the OF 1400 (Page 11). 24

25 Dovetail joints 3 Templates OF 1010 OF 1400 Open dovetail joints* Item Dovetail joint size 14 mm Workpiece thickness mm (Ø 8.5 and 17 mm copying rings for the OF 1010 included) Suitable cutters, 8 mm shank Dovetail cutter Ø 14.3 mm, 10 HW Spiral groove cutter Ø 6 mm HS Spiral groove cutter Ø 6 mm HW Dovetail size 20 mm Workpiece thickness mm (Ø 13.8 and 24 mm copying rings for the OF 1010 included) Suitable cutters, 8 mm shank Dovetail cutter Ø 20 mm, 10 HW Spiral groove cutter Ø 10 mm HS Spiral groove cutter Ø 10 mm HW * With special copying rings for the OF 1400 (Page 11). 25

26 Dovetail joints 4 Templates OF 1010 OF 1400 Slot joints* Item Dovetail size 6 mm Workpiece thickness 6 10 mm (Ø 8.5 mm copying ring for the OF 1010 included) Suitable cutters, 8 mm shank Spiral groove cutter Ø 6 mm HS Spiral groove cutter Ø 6 mm HW Dovetail size 10 mm Workpiece thickness mm (Ø 13.8 mm copying ring for the OF 1010 included) Suitable cutters, 8 mm shank Spiral groove cutter Ø 10 mm HS Spiral groove cutter Ø 10 mm HW * With special copying rings for the OF 1400 (Page 11). 26

27 Dovetail joints 5 Templates OF 1010 OF 1400 Dowel joint* Item Dowels sizes up to 10 mm in 32 mm template (Ø 13.8 mm copying ring for the OF 1010 included) Dowel drill, 8 mm shank Ø 5 m Ø 6 mm Ø 8 mm Ø 10 mm Drill, 8 mm shank Ø 5 m * With special copying rings for the OF 1400 (Page 11). 27

28 Guide rails OF 1010 OF 1400 OF 2200 Making grooves in surfaces* Item FS/2 guide rails Length 800 mm Length 1,080 mm Length 1,400 mm Length 1,900 mm Length 2,400 mm Length 3,000 mm Length 5,000 mm Connector piece (1 each) For connecting two guide rails for long workpieces Clamps (2 each) Length 120 mm Length 300 mm Clamping width 160 mm (1 each) * Also for the OF 900 and the OF OF 1010 guide stop included with the power tool. The guide stop for the OF 1400 is on Page 12. The guide stop for the OF 2200 is on Page

29 MFS 1 routing template Templates OF 1010 OF 1400 OF 2200 MFS for flexible and versatile routing of cut-outs and radii. Item MFS 400* for routing right-angled or round shapes using a copying ring. Simple duplicating of gradient angles for stairs possible Area: 300 x 100 mm, Radius: Ø mm MFS 700* for routing right-angled or round shapes using a copying ring. Simple duplicating of gradient angles for stairs possible Area: 600 x 300 mm, Radius: Ø 40 1,200 mm * Items included: 2 angle stops, tilt protector, circle routing insert, operating tool 29

30 MFS 2 routing template Extension OF 1010 OF 1400 OF 2200 MFS extension profile Item Extension profile with scale with the MFS 400 or the MFS 700 Areas greater than 600 x 300 mm Radii greater than Ø 1,200 4,000 mm 2x profile, length 200 mm x profile, length 400 mm x profile, length 700 mm x profile, length 1,000 mm x profile, length 2,000 mm, without scale

31 APS worktop template OF 1400 OF 2200 APS worktop routing template for joining profiled worktops Item For corner and panel connections with depths of up to 900 mm. Routing for commercially available connection fittings on the rear of panels For Ø 30 mm copying ring and 14 mm cutter diameter Suitable cutters, 12 mm shank Reversible groove cutter Ø 14 mm, HW Groove cutter Ø 14 mm HW

32 Router carriage OF 1400 OF 2200 Router carriage for making surface hollows Item To precisely and more easily routing surface hollows using the MFS 400 or the MFS 700 routing templates. With Ø 30 mm copying ring (please order routing templates separately)

33 Routing aid OF 1010 OF 1400 OF 2200 Aids for routing on narrow edges Item Ensures a secure position while routing grooves for door seals or security fasteners; material thickness mm

34 OFK 500 edge router The compact edging professional. The OFK 500 weighs in at only 1.4 kg and is perfectly balanced, This makes it handy and perfect for use in a horizontal or vertical manner with the highest run-out accuracy. Easy handling High run-out accuracy Precise cutting results Quick cutter replacement Routing depths can be set to a precision of 1/10 mm Technical specifications Power consumption Idling speed Router stroke Routing diameter max. Dust extraction connection Ø Weight 450 W 28,000 rpm 20 mm Special cutters 27 mm 1.4 kg 34

35 Cutters OFK Ogee cutters ØD NL B R F Replacement ball bearing guide with clamping screw VE 1 each Chamfer cutters ØD NL B R F Replacement ball bearing guide with clamping screw VE 1 each

36 Cutters OFK Edge trimming cutter ØD NL B R F Edge trimming cutter without ball bearing ØD NL B R F Replacement ball bearing guide with clamping screw VE 1 each

37 OFK 700 edge router The multi talented edger. The OFK 700 EQ is a multi-talent among edge trimmers. It makes flush trimming edge and surface protrusions easy. It doesn t matter if the workpiece is big or small, or the edges straight or curved. Detachable router table with large support surface 1.5 tilted router table Routing depths can be set to a precision of 1/10 mm Quick cutter replacement Technical specifications Power consumption Idle engine speed Routing depth max. (1.5 table) vertical horizontal Router stroke Routing diameter max. Dust extraction connection Ø Weight 720 W 10,000 26,000 rpm 9 mm 5 mm 14 mm 30 mm 27 mm 2.0 kg 37

38 Cutters OFK 700 MFK Edge trimming cutter ØD NL GL R F Reversible edge trimming cutter (not shown) ØD NL GL R F Replacement cutters VE 4 each 12 x 12 x Ogee cutters ØD NL GL R F

39 Cutters OFK 700 MFK Rounding edge trimming cutter with ball bearing ØD NL GL R F Replacement ball bearing guide VE 2 each Ø Chamfer cutters ØD NL GL R F Reversible chamfer cutter (not shown) ØD NL GL R F * * * Replacement cutters VE 2 each 12 x

40 MFK 700 modular router Modular work on edges in different ways. Its modular design makes the MFK 700 a multi purpose tool that saves you money. For different jobs, there are two router tables. The motor is protected against overheating whenever edges made of hard materials are being routed. Exchangeable router tables Large surface area Easy router settings Electronic speed adjustment switch Motor temperature monitoring Technical specifications Power consumption Idle engine speed Router stroke Routing diameter max. Dust extraction connection Ø Weight 720 W 10,000 26,000 rpm 14 mm 32 mm/1 27 mm 1.9 kg 40

41 Side fence OFK 700 edge router OFK 700 MFK 700 Side fence with fine setting Item Cast aluminium side fence with movable stop jaws. Fine adjustment with 1/10 mm precision. With extractor hood (included in the MFK 700 set)

42 Router tables 1,5 0 OFK 700 MFK router table for veneered surfaces 0 router table for untreated surfaces 1,5 0 Router table 1.5 table Item For easy flush trimming of edging on veneered surfaces. Because the table is tilted at 1.5, surfaces will not be damaged Router table 0 table Item For workpieces that are veneered or coated, the laminate must be milled precisely at right angles to the surface

43 Tools for the toughest demands Overview of router bits A handy guide

44 Festool router bit selection This guide provides information on the extensive selection of Festool router bits. You will find bits for edge routers along with the edge routers in the accessories section. Router bit dimensions For optimal results, always clamp the router bit as far as possible. At least up to the mark on the shaft. GL (mm): Total length NL (mm): Working length Ø D (mm): Cutter diameter s (mm): Shank diameter Fα ( ): Chamfering angle Marking for minimum clamping length n max. = maximum router speed High performance, high speed steel This steel has mechanical and thermal properties that are best suited for routing soft materials such as, e.g., spruce and pine. Tungsten carbide HW router bits are mostly composed of tungsten carbide. For this reason, these router bits are particularly suitable for working on hardwoods, panel materials and plastics. VE = packaging unit 2

45 Groove cutter 1 1 Solid tungsten carbide groove cutter with standard blade ØD NL GL R Fa More security against small diameter bits breaking because of the low vibration tungsten carbide cutter design The partially ground standard tungsten carbide standard blade provides an increased service life when drilling panel materials 3

46 Groove cutter 2 2 Groove cutter with standard blade ØD NL GL R Fa * Long router bit service life even for plunge cutting because of the soldered standard tungsten carbide blade * for slot jointing using Festool VS 600, with fine precision in dia meter 4

47 Groove cutter 3 3 Groove cutter with standard blade s = 12 mm ØD NL GL R Fa ) ) ) ) Long router bit service life even for plunge cutting because of the soldered standard tungsten carbide blade Groove cutter dimensions Seal Width Depth 1) Planet HS ) Schall-Ex L ) Schall-Ex RD ) Draft excluders ) Double seals ) Schall-Ex Ultra

48 Groove cutter Single-edged groove cutter with standard blade Single-edged router bits in HS steel are ideally suited for softwood applications 5 Spiral groove cutter with standard blade * * * * * For slot joint connections with the Festool VS 600, with extra precision in the diameter. 6

49 Groove cutters/step mills Single-edged reversible groove cutters with standard blade Replacement blades VE 4 each Reversible base cutters VE 4 each Main blade VE 4 each Ø 8 20 x Ø x Ø x Ø x Ø x Ø x Ø x Ø x Step cutters s = 12 mm ØD1 ØD2 T1 NL Fα Particularly suited for cutting edges during window construction The step cutter can be securely moved on the edge of a window casement by using router accessories 7

50 Ovolo bits Ovolo bit For decorative front design of inlays With partially ground standard blade suitable for plunge cuts in furniture 9 Bullnose bit with ball bearing Replacement ball bearing guide VE 2 each Ø Optimally suited for 28 mm thick laminated wood panels The tracer bearing lies directly on the template in this way panels can be optimally profiled without the use of a copying ring 8

51 Roundover bits Roundover bit with 2 ball bearings ØD 16.7 NL 9 GL 49 R 2 Fα * * * * * * * * * s = 12 mm Replacement ball bearing guide VE 2 each Ø Ø With Ø 12.7 mm ball bearing for ogee cuts. With Ø 9.5 mm ball bearing for ovolo cutting. * Delivered items include Ø 12.7 mm ball bearing and Ø 9.5 mm ball bearing. 9

52 Ogee cutter Roundover chamfer bit with ball bearing guide Replacement ball bearing guide VE 2 each By using a roundover chamfer bit, a 6 mm radius that impinges on a chamfer at an edge can be cut without attachments Thus the chamfer cutter (Page 11, No. 12) and the roundover chamfer bit with a conical ball bearing work together perfectly

53 Chamfer cutters Chamfer cutters with ball bearing guides º Replacement ball bearing guide VE 2 each Ø s = 12 mm Replacement ball bearing guide VE 2 each Ø Reversible chamfer/edge-trimming cutter with ball bearing guide Replacement ball bearing guide VE 2 each Replacement blades VE 4 each Ø x

54 Flute cutters Flute cutters ØD 8 NL 8 GL 38 R 4 Fα s = 12 mm Flute cutters with ball bearing guides Replacement ball bearing guide VE 2 each Ø For every flute cutter, Festool offers an ogee cutter with the same radius 12

55 Round nose cutter Round nose cutter Routing with the copying ring Because of the long working length, curved or round channels can be cut with the aid of a template and copying ring 17 Round nose cutter with ball bearing guide Replacement ball bearing guide VE 2 each Ø Routing without a copying ring: Curved or round channels can be cut using the ball bearing with the aid of a quickly made template 13

56 Edge trimming cutter Edge trimming cutter with ball bearing ) ) Replacement ball bearing guide VE 2 each Replacement ball bearing guide VE 2 each 1) ØD 12.7 = ball bearing, lower 2) ØD 19 = ball bearing, upper Ø Ø Reversible blade edge trimming cutter with ball bearing Replacement ball bearing guide VE 2 each Replacement blade VE 4 each Ø x The replaceable and reversible blade provides lasting cutting dimensions and precision, and is optimally suited for edge trimming excess panel material 14

57 Chamfer/edge trimming cutter with ball bearing guide Chamfer/edge trimming cutter with ball bearing guide ØD NL GL R F α / Replacement ball bearing guide VE 2 each Ø flush cut chamfered flush cut + chamfered 21 Drilling cutter ØD NL GL R F α For cut-outs of any kind without pre-drilling, the drilling cutter goes right through the coating material www. festool. c o m 15

58 Rebating cutters Rebating cutter with ball bearing guide ) Replacement ball bearing guide VE 2 each Ø Replacement ball bearing guide set x Ø 9,5 / 1x Ø 12,7 / 1x Ø 16 / 1x Ø 19 / 1x Ø 22 1) Items included: 1 ball bearing 12.7 with 9.5 mm rebate depth. 23 Reversible rebating cutter with ball bearing guide set ) Replacement blade 12 x Replacement ball bearing set 1x Ø 9,5 / 1x Ø 12,7 / 1x Ø 16 / 1x Ø. 19 / 1x Ø ) Items included: ball bearing set from 9.5 to 22 mm. 16

59 Dovetail cutter Dovetail cutter with pre-cutter ØD 14.3 NL 13.5 GL 46 R Fα Dovetail cutter For use with the VS 600 joining system: 1) partially covered dovetail connection 2) open dovetail connection ) ) ) ) ) ) s = 12 mm s = 12 mm

60 Hand rail cutter Hand rail cutter / Always, whenever visible fittings interfere with the overall image of a workpiece, a covered hand rail is an elegant alternative In a single pass, the entire hand rail can be routed on a door or drawer face 27 Recessed grip cutter with ball bearing guide Replacement ball bearing guide VE 2 each Ø

61 Tongue and groove cutter Tongue and groove cutter Mitre tongue and groove cutter s = 12 mm n max. 22,000 Settings table for tongue and groove cutter Wood thickness Height Y dimension Stop X dimension Workpiece upright 1 3 Stop Workpiece flat 1 2 Stop Machine table Machine table 19

62 Script cutter/v-groove cutter Script cutter A fine-grained wood is suggested for script cutting because the power tool can then be guided without jerking 31 V-groove cutter ØD 14 NL 7 GL 50 R Fα Available for making groove decorations at 2 different angles 20

63 Groove cutting disc/cutter spindle d 32 Groove cutting disc ØD B d R Fα * * * * * * * * * Without cutter spindle. 33 Cutter spindle (not shown) ØD B d GL Fα Cutter spindle with ball bearing guide ØD NL d GL Fα Replacement ball bearing guide VE 2 each Replacement ball bearing guide VE 2 each Ø Ø

64 Laminate cutter/parquet cutter Laminate cutter ØD B T GL Fα Replacement slot cutting blade Replacement ball bearing guide VE 2 each Ø Parquet cutter ØD NL T GL Fα Replacement slot cutting blade Ø

65 Hinge location cutter/dowel drill Hinge location cutter Dowel drill 1) Without centre point. 1) 2) ) 3) ) ) ) 39 Dill bit ØD NL B R Fα 2) For drilling rows of holes. 3) For use with the VS 600 joining system dowel unit ) 23

66 T-groove cutters/profile cutters T-groove cutter ØD1 ØD2 NL1 NL2 Fα For routing T-grooves, picture slots and keyhole mountings in solid wood and panel materials 41 Profile cutter ØD NL GL R1 R Profile cutter for routing profiled inlays or cassette fillings 24

67 Profile cutters Roman ogee cutter with ball bearing guide ØD NL GL R1 R Replacement ball bearing guide VE 2 each Ø Classic profile cutter for panel edges and decorative strips 43 Multi-profile cutter with ball bearing guide ØD NL GL R1 R Replacement ball bearing guide VE 2 each Ø Classic profile cutter for panel edges and decorative strips Optimised cutting angle for fewer burn marks 25

68 Profile cutters Profile cutter ØD NL GL R1/2 R Profile cutter with ball bearing guide Replacement ball bearing guide VE 2 each Ø

69 Counter profile cutters Counter profile cutter spring with ball bearing guide ØD NL B R Fα Replacement ball bearing guide VE 2 each Ø Counter profile groove cutter with ball bearing guide ØD NL B R Fα Replacement ball bearing guide VE 2 each Ø

70 Counter profile cutter Profile tongue cutter ØD NL B R Fα s = 12 mm ØD NL B R Fα Profile tongue cutter ØD NL B R Fα s = 12 mm ØD NL B R Fα

71 Facing cutters Facing cutter with ball bearing guide s = 12 mm n max. 22,000 This facing cutter is very suitable for cutting classic inlays 51 Facing cutter without ball bearings s = 12 mm n max. 22,

72 Facing cutters/profile cutters Plasterboard V-groove cutter α Bestell-Nr , Facing cutter with ball bearing guide * * Without ball bearing guide. s = 12 mm Replacement ball bearing guide VE 1 each

73 Ogee cutter with ball bearing guide Profile cutter with ball bearing guide s = 12 mm Replacement ball bearing guide VE 2 each n max. 22,000 Ø Profile cutter s = 12 mm / Replacement ball bearing guide VE 2 each n max. 22,000 Ø

74 Aluminium cutter Aluminium cutter V-groove cutter Milling of aluminium composite panels with the Festool PF 1200 aluminium composite milling machine *. * Further information can be found in the Festool main catalogue or at 32

75 Special cutters for mineral-based solid surface materials Reversible blade edge trimming cutter with ball bearing guide s = 12 mm Replacement ball bearing guide VE 2 each Reversible blades VE 4 each Ø x Reversible blade groove cutter s = 12 mm * Reversible blades VE 2 each 50 x * For use with the APS 900 worktop template. 33

76 Special cutters for mineral-based solid surface materials Solid tungsten carbide spiral groove cutter s = 9.53 mm ØD 9.53 NL 27 GL 70 R Fα s = 10 mm s = 12 mm s = 12.7 mm Solid tungsten carbide roughing and finishing router bit s = 12 mm s = 12.7 mm

77 Special cutters for mineral-based solid surface materials Edge trimming cutter with ball bearing, top s = 12 mm ØD 28 NL 25 GL 80 R Fα ) s = 12.7 mm ) 1) Replacement ball bearing guide VE 1 each 1) Ball bearing fits both cutters. Ø Edge trimming cutter crossover cutter ball bearings s = 12 mm (11 ) ) s = 12.7 mm (11 ) ) 2) Replacement ball bearing guide VE 1 each 2) Replacement ball bearing guide VE 1 each Ø Ø ) Both ball bearings included with delivered items. 35

78 Special cutters for mineral-based solid surface materials Chamfer cutter s = 12 mm ØD 23 NL 25 GL 66 R Fα s = 12.7 mm Chamfer cutter with ball bearing, top s = 12 mm ØD 28 NL 25 GL 80 R Fα * s = 12.7 mm * * Replacement ball bearing guide VE 1 each Ø

79 Special cutters for mineral-based solid surface materials Chamfer cutters with ball bearing guides s = 12 mm ) s = 12.7 mm ) 1) Replacement ball bearing guide VE 1 each Reservoir cutter with ball bearing guide s = 12 mm ) ) ) ) ) ) s = 12.7 mm ) ) ) ) ) ) 2) Replacement ball bearing guide VE 1 each n max. 22,

80 Special cutters for mineral-based solid surface materials Chamfer cutter undercut with ball bearings s = 12 mm ) s = 12.7 mm ) 1) Replacement ball bearing guide VE 1 each Ø Roundover chamfer bit with ball bearing guide s = 12 mm ) s = 12.7 mm ) 2) Replacement ball bearing guide VE 1 each Ø n max. 16,000 Through the combined use of the chamfer cutter and the roundover chamfer cutter, counters and worktops can be made to look modern 38

81 Special cutters for mineral-based solid surface materials Plane cutter s = 12 mm ØD NL GL R Z s = 12.7 mm ØD NL GL R Z Chamfer cutter with ball bearing guide Using the chamfer cutter, excess laminate on the edges panels can be removed (liquids will stay on the panel) s = 12 mm ØD NL GL R Z s = 12.7 mm ØD NL GL R Z Replacement ball bearing guide VE 1 each Ø

82 Special cutters for mineral-based solid surface materials Ogee cutter with ball bearing guide s = 12 mm s = 12.7 mm Replacement ball bearing guide VE 1 each Ø n max. 22,000 Ogee cutters with radius from 3 mm to 25.4 mm 40

83 Special cutters for mineral-based solid surface materials Chamfer cutter undercut with ball bearings HW s = 12 mm HW s = 12.7 mm Replacement ball bearing guide VE 1 each Ø n max. 22,000 The result of perfect profile machining a mineral stone wash basin with a modern design. 41

84 TTS Tooltechnic Systems AG & Co. KG Wertstraße 20 D Wendlingen represented in Great Britain by: TTS Tooltechnic Systems GB Ltd Saxham Business Park Saxham Bury St Edmunds Suffolk IP28 6RX GREAT BRITAIN Phone: +44 (0) Fax: +44 (0) represented in Ireland by: TTS Tooltechnic Systems Ireland Ltd. Unit 1B Century Business Park St. Margarets Road Finglas Dublin 11 IRELAND Tel (0) Tel (0) Fax +353 (0) pf@festool.ie Festool GmbH Export Department Wertstraße 20 D Wendlingen Phone (+49) 70 24/ Fax (+49) 70 24/ ebg@tts-festool.com Item No Subject to change without notice. All rights reserved. Products may differ from those pictured. Prepared for TTS Tooltechnic Systems AG & Co. KG, DE Wendlingen, 09/2008