Since 1950 Commercial Division

Transcription

1 Since 1950 Commercial Division *These images represent the types of structures we specialize in. Aluminum storefronts are not available

2 MASONRY (AS) FRAME Multiple Application 5-3/4 OAL 16 Gauge Galvaneal Frame Closer & Panic Reinforced Embossed for 90M Fire Rating Reinforced For Closer & Panic Special Mortar Guards Prevent Mortar Fill In Frame Prepped For Silencer Available 4 Face Head Jamb Steelcraft Locations ASA Strike Welding Service Available 4" Head frame face dimension 2" Head frame face dimension 4-7/8" Throat 5-3/4" Frame depth 4-7/8" Throat 5-3/4" Frame depth DRYWALL (KDDW) FRAME 5-5/8 or 5 7/8 OAL Accurate Miters Make Corners Attractive 16 Gauge Galvaneel Frame Tension Anchor Standard Reinforced For Closer & Panic 10 Guage Hinge Reinforcements Embossed for 90M Fire Rating Intergal Corner Tabs For Locking Miters Steelcraft Locations ASA Strike Prepped for Silencers 2" Face (Interior Application Only) 4-5/8" or 4-7/8" Throat 5-3/4" Frame Depth SPLIT FRAME 16 Gauge Galvaneal Frame 4-1/2 Hinge Prep Steelecraft Location Prepped for Silencers Non Kerf Application ASA Strike Prep Wrap around frame or butted application Prefinished Doors In Stock for all Frames on this Page! Throat Sizes in 3 models for jamb depth ranges 3 1/ / See Hollow Metal R/O Info Page 14 1

3 Masonry Frames 2/6 Head 2/8 Head 3/0 Head 3/0 + 4 Head 3/6 Head 4/0 Head 4/0 + 4 Head 5/0 Head 5/4 Head 6/0 Head Hinge Jamb LH Strike Jamb LH Hinge Jamb RH Strike Jamb RH 5-3/4 5-3/ A A Drywall Frames 2/6 Head 2/8 Head 3/0 Head 3/6 Head 4/0 Head 5/0 Head 5/4 Head 6/0 Head Hinge Jamb LH Strike Jamb LH Hinge Jamb RH Strike Jamb RH Split Frames 2/6 Head 2/8 Head 3/0 Head 3/6 Head 4/0 Head 5/0 Head 5/4 Head 6/0 Head Hinge Jamb LH Strike Jamb LH Hinge Jamb RH Strike Jamb RH 5-5/8 4-5/8 Throat /2 to 6 3-1/2-5 Throat Small /8 5-5/8 4-7/8 Throat 4-5/8 Throat A /8 to 9 4-5/8-8 Throat Medium to Throat Large /2 to 6 3-1/2-5 Throat Small /8 to 9 4-5/8-8 Throat Medium /8 4-7/8 Throat A to Throat Large

4 Rediframe - Non Kerf Light Commercial 18 Guage Frame Prefinished Ivory or Brown 4-1/2 Hinge Prep Steelecraft Location Standard Snap On Modern Casing Silencers Included Non Kerf Application ASA Strike Prep Prefinished Doors In Stock 4-7/8 Throat, in Stock Slip-on Drywall Application (Fixed Frame - Interior Application Only) Works perfectly with Hollow Metal and our Wood Doors. Rough Openings Measure rough opening for door frames and sidelites from finished floor. Frames may be conveniently installed afterwalls are finished and flooring application is layed. * Same Rough Openings on pages 3 & 4 Rediframe Closure Parts Brown 4-7/8 Throat Ivory 4-7/8 Throat CLOSURE HEADS CLOSURE LEGS CLOSURE LEGS 2/8 2/10 3/0 4/0 5/0 6/0 LH RH DBL LH RH DBL

5 DUNBARTON COMMERCIAL SPLIT 4-1/2 Steelcraft Hinge Locations Non Kerf Application Standard Modern Snap on Casing ASA Strike Prep Standard Split Sizes 4-5-1/ / / /4 Prefinished Ivory or Brown Prefinished Doors in Stock Silencers included Availability: & Multiple Application (Adjustable Split Frame - Interior and Exterior Application) Brown 4 to 5-1/4 Throat Ivory 4 to 5-1/4 Throat Brown 5 to 6-1/4 Throat Ivory 5 to 6-1/4 Throat Brown 6 to 7-1/4 Throat Ivory 6 to 7-1/4 Throat Brown 7 to 8-1/4 Throat Ivory 7 to 8-1/4 Throat BASE PARTS Brown Ivory CLOSURE HEADS CLOSURE LEGS CLOSURE LEGS 2/8 2/10 3/0 4/0 5/0 6/0 LEGS LEGS DBL LH RH DBL /8 2/10 3/0 4/0 5/0 6/0 LEGS LEGS /8 2/10 3/0 4/0 5/0 6/0 LEGS LEGS /8 2/10 3/0 4/0 5/0 6/0 LEGS LEGS /8 2/10 3/0 4/0 5/0 6/0 LEGS LEGS BASE BASE BASE BASE LEG LH LEG RH LEG DBL LG LH LEG RH LEG DBL Purchase a Hollow metal door(s), clear coated Birch or Brown Birch door(s) IN STOCK Get a Brown door & frame in a matter of days! 4

6 161 Prep 2/6 2/8 3/0 3/6 4/0 FLUSH DOOR LH/RH RH LH LH/RH RH LH LH/RH RH LH LH/RH RH LH LH/RH RH LH SI PANEL RH LH TWO PANEL SQUARE RH LH RH LH ONE PANEL PANIC REINFORCED DOOR 2/6 2/8 3/0 4/0 FLUSH DOOR SI PANEL RH LH TWO PANEL SQUARE RH LH RH LH ONE PANEL Features and Benefits: * Bevel Edge * Polystyrene Core for Insulating Value * All for use with Hollow Metal Frames, Commercial Rediflex and Rediframe * Steelcraft Hinge Locations * Deadbolt Available - Leadtimes may Occur * All Available up to 90 Minute Fire Rating * R rating 7.0 Custom Types of Doors Available - Just Ask 5

7 Residential CLOSER KITS Residential CLOSER KITS Commercial Division DUNBARTON KERF RESIDENTIAL SPLIT 4 Prem Door Spec Hinge Location Kerf for Weather Strip For use with Wood Casing Optional Metal Snap On Casing 2 PC Adjustable Strike Three Different Adjustable Strike Finishes Prefinished Bright White Availability:, & 8/0 4-1/2-5-1/2 5-1/2-6-1/2 6-1/2-7-1/2 Dunbarton Rediflex Frames Single Door Unit Dunbarton Rediflex Frames For ADA Sill Deduct 7/8 STOCK Standard Sill 2/6 2/8 2/10 3/ Nominal Door Size Rough Opening Size Width Height Width Height 2'0" 6'8" 25-1/4" 81-5/8" 2'6" 6'8" 31-1/4" 81-5/8" 2'8" 6'8" 33-1/4" 81-5/8" 2'10" 6'8" 35-1/4" 81-5/8" 3'0" 6'8" 37-1/4 81-5/8" REDIFLE CASING SETS 2/8 3/0 MODERN STOCK Standard Sill STOCK 8/0 Standard Sill STOCK ADA Sill STOCK ADA Sill STOCK 8/0 ADA Sill (Special Order) CASING RETAINER BAG SET BOTH SIDES Flush Six Panel Two Panel Two Panel Roman Multiple Application (Adjustable Split Frame - Interior and Exterior Application) Four Panel New England Three Equal Panels Three Panel Craftsman Note: These are the Residential MHD doors that work harmoniously with this frame system.

8 Commercial Division Hollow Core MINUTE 1-3/4 2/0 2/4 2/6 2/8 2/10 3/0 3/6 4/0 2/0 2/4 2/6 2/8 2/10 3/0 Primed Hardboard Skin 8/0 WS WS WS WS WS WS Birch Rotary Cut Skin 8/0 Clear Birch Rotary Cut Skin 8/0 Brown Birch Rotary Cut Skin 8/0 Oak Plain Sliced Skin 8/0 Imperial Oak Skin 8/0 Regency Walnut Skin 8/0 WOOD DOOR STOCK INFORMATION 7

9 45-60 MINUTE 1-3/4 90 MINUTE 1-3/4 3/6 4/0 2/0 2/4 2/6 2/8 2/10 3/0 3/6 4/0 2/0 2/4 2/6 2/8 2/10 3/0 3/6 4/0 8 = Stock WS = Wood Stave

10 TOP RAIL STILES FPC-9: Particleboard Core Door 9-Ply CORE SPECIFICATIONS Thickness: 1-3/4 Core: Particleboard which complies with ANSI A LD2 or 1-LD1. Veneer: Rotary Natural Birch and Plain Sliced Red Oak Aspen Stiles: 1-1/4 min. (before trim) Structural Composite Lumber (SCL). HDF CROSSBAND VENEER SCL Rails: Adhesives: 2-1/4 min. (before trim) Door assembly Type I Veneers Type II PLASTIC LAMINATE DOORS AVAILABLE VENEERS AVAILABLE MAHOGANY MAPLE WHITE MAPLE QTR SAWN WHITE OAK CALL FOR QUOTE TOP RAIL BONDED BOTTOM RAIL FD9-90: Fire Resistant Core Door 45 to 90 min. SPECIFICATIONS Max Size: Singles: 4 0 x 10 0 Pairs: 8 0 x 10 0 Thickness: 1-3/4 STILES BONDED (MATCHING VENEER BAND) CORE Core: Veneer: Stiles: Rails: Adhesives: Incombustible non-asbestos engineered mineral core 9-Ply 1 Firestop laminated to 1/2 (before trim) wood... veneered with compatible veneer band. 2 Firestop top and bottom. Door assembly Type I Veneers Type II (Type I Available) SBC LABELS FIRE DOORS NEUTRAL PRESSURE & CATEGORY B POSITIVE PRESSURE HDF CROSSBAND FACE VENEER BOTTOM RAIL BONDED Fire Rating: Neutral (standard) and Positive Pressure Category B** Intertek Testing Service/Warnock Hersey (ITS-WH) 90-minute B label Standards: ANSI/WDMA I.S.1A and AWI Section 1300 *Minimum 5.5 from any edge of door including hardware cutouts, to meet labeling and warranty requirements. **Contact SBC for size restrictions 9

11 Masonry Wire Anchor Wood Stud, Steel Stud or Masonry Anchors PEEP SITE 1755 US4, 26d, 10R #64 Silencer 4" 3/8" 4-7/8 Strike ASA Double Door Strike US10R US26D Kick Plate 6 x 28 US3, US261, US10R 6 x 30 US3, US260, US10R 6 x 34 US3, US26D, US10R Push Plate 3-1/2 x 15 US3, US10, US28 #570 Dustproof Strike Faceplate measures 1-3/8 x 2-7/8 Barrel is 7/8 dia. x 2 depth US10R US26D #43 Push and Pull Plate 3-1/2 x 15 US3, US10, US28 #282D #283D 24 or 30 rod US10B US26D US10B US26D #278D SURFACE BOLT 6 US3 Strike Filler Plate VINYL SEAL 156V VINYL SWEEP 96V 3/4" 1/4" 7/8" 1/4" 7/8" 10

12 BEVELED DOOR EDGE SET 543 1" o o o o 1" 1 3/4" Required for Fire Rated pairs with double vertical rod exit devices SADDLE THRESHOLD 424 shold BEVELED EDGE Z ASTRAGAL ON INACTIVE LEAF /8" 1 3/4" 87 o 93 o 140P 7/8" POSITIVE PRESSURE CATEGORY B SEAL e and Smoke Seal STOP DOOR cone Bulb Fire and Smoke Seal STOP HEAD & LATCH JAMB DOOR HINGE JAMB SPRING ADJUSTABLE ASTRAGAL SEAL SET 140P 1/4" 1/2" 1 1/16" SADDLE THRESHOLD shold 426 3/8" to 3/4" Spring loaded Adjustable 6" Typical Wall.175 1/2" 9/16" polypropylene Typical Wall.125 1/2" 3/8" 4" Plain bearing hinge Ball bearing hinge spring Hinge NRP Hinge Pinned Non Removable EISTING MASONRY HOLLOW METAL FRAME ANCHORS NEW MASONRY WOODSTEEL STUD COMPRESSION FINISH DRYWALL Dynabolt 4" 3/8" 11

13 We have a full line of architectural hardware - refer to our sales experts for your needs 12

14 Fire Protective Ceramic Safety Glass Pyran Platinum F Material 3/16" (5mm) thick glass ceramic Neutral coloration - clear and wireless Advanced manufacturing process eliminates the need for surface polishing 10 year Manufacturer Warranty Weight: 2.5 lbs./sq. ft. STC 31 rating Fire-rating information: CAN/ULC-S104, ULC CAN4-S106 with closed cell PVC foam glazing tape like NGP GT-116, GT-118, or GT132 IBC applicable edition may limit maximum size allowable Impact Safety Rating Information: Meets ANSI Z97.1, Class A Meets CPSC 16CFR 1201 (Category I and II) Complies with IBC requirements for use in doors, side-lites, transom lites and borrowed lites 3/16" *HM-V *HM-NL-3 *HM-NL4 *HM-NL5 HM-G HM-LV *Stock Sizes for Fire Rating HM-4 HM-6 HM-9 HM NEW! REPLACES WIRE GLASS Max. Visible Glass Area Max. Width Max. Height Rating Application (Sq. Inches) Visible Glass Visible Glass 20, 45, 60, 90 Minute Doors* 2,736 36" 76" (non-temp rise) 20, 45, 60, 90 Minute Side-lites, 3,422 76" 76" Borrowed lites, Transom lites 180 Minutes Doors* including " 33" temp-rise r No Vision Door Louver for 1-3/4" Thick Doors L-700-R Materials & Finishes 18 ga. cold rolled steel Mitered and welded corners Welded reinforcing clips at corners Inverted V design Blades 24 ga. steel; hemmed edges Counter-sunk mounting screw-holes #8 x 3/4" Phillips head SMS Available in uneven and fractional sizes Free area 55% HM-LV Fire-rated Fusible Link Louver for 1-3/4" Thick Doors up to 90 Minutes L C *up to 90 minutes. Materials & Finishes 18 ga. cold rolled steel frame 18 ga. cold rolled steel adjustable Z blades Mitered corners secured with reinforcing clips Stainless Steel Spring 165 Fusible link Free area 40% #8 x 3/4" Phillips head SMS 3/16" 1 3/4" 3/16" 165 FUSI STOP HM-LVL FUSIBLE LINK STOP BLADE 1" OPERATING LEVER ORDER SIZE LESS 1/8 ORDER SIZE & DOOR CUTOUT ORDER SIZE PLUS 7/8 (O.D. FRAME) 13

15 COMMERCIAL DOOR HANDING (RHRA) (LHRA) SHUSTERʼS Building Components GALVANNEAL steel provides superior durability and protection against rust in Artek Doors and Frames What is GALVANNEAL? It is steel with a matte-gray galvanneal coating applied by the steel producer to both sides of the sheet, suitable for immediate painting without further treatment except normal cleaning. Why use GALVANNEAL? To provide superior and inexpensive protection against rust. To eliminate the need for costly touch-up prior to finish painting. To eliminate the need for costly packaging from the factory. Where to use GALVANNEAL? Common interior and exterior environments in residential, commercial and industrial construction. Is GALVANNEAL the same as Galvanize? No. Galvanneal is a zinc-iron alloy coating. Galvanize is a bright zinc coating with a multifacteted crystal structure. Galvanneal is provided at no charge. Galvanize is an optional extra. Are there other names for GALVANNEAL? Yes. Satincoat, Wipecoat and Galvanneal are synonymous. Product storage Do not allow moisture or liquid of any kind to remain on or trapped between surfaces. Store Artek products off the ground and in covered, dry places. Inspect stored products regularly. If moisture is present, dry immediately. Polystrene Core 1-3/4 polystrene composite construction. All reinforcing boxes contain polystyrene. Flush, 6 panel or 2 panel square embossed surface. R factor: 7.0 STC 26 in 20 gauge material. GALVANNEAL provides an excellent base for finish painting. Surface must be clean and dry, if required, to clean surface oils and grease use ZYLOL or TULUOL. Paint locally or on site according to the application, local conditions and paint specifications. For most interior and exterior applications, directly apply an alkyd or acrylic latex paint in semi or gloss finish. Primer is not required. Do not use chemical pretreatments or mineral spirits. Why coat steel with Zinc? It is the least expensive way of protecting steel against corrosion. Zinc, with it s very low corrosion rate, shields the steel against most common environments, for as long as the zinc lasts. Technical Bits This material may not be reproduced in its entirety or in part, in any form whatsoever. Prices and specifications subject to change without notice. SHUSTER S BUILDING COMPONENTS 2920 Clay Pike Irwin, PA ASTM A653/653M - Standard Specifications for Steel Sheet, Zinc Coated (Galvanized) or Zinc- Iron Alloy Coated (Galvanneal) by the Hot-Dip process. Arteks standard grade of steel is Commercial Steel (CS) type B with the coating designation A40 having a minimum thickness of.40 oz/ft 2, total both sides (metric equivalent is ZF120 with 120g/m 2 ).

16 SHUSTER S BUILDING COMPONENTS 2920 Clay Pike North Huntingdon, PA