Wood Door Technical Manual Architectural Accessories Details. Revised Nov., 2017
|
|
- Caren Alexander
- 6 years ago
- Views:
Transcription
1 Architectural Accessories Details Revised Nov., 2017
2 Handing Chart Index Graham Maiman May, 2017 Contents Construction Detail... 2 Wood Moulding Louver Unites - Wood and Metal... 5 Vision Panels - Wood and Metal... 6 Factory Installed Glass Astragals/Edges...10 Dutch Door Doors with Transoms (Non Fire-Rated) Doors with Transoms (Fire-Rated) Wicket Door...23 Special machining - Rabbiets/Radius Edge...24 Flush Bolts...25 Fire Door Plant-Ons...26 Full Glass / Full Warranty Door...27 ElectroLynx...28 Door Glazing Charts Wood Frames
3 2 GRAHAM Graham Maiman MAIMAN Construction Details Meeting Edge Options No Bevel Bevel Rabbeted Parallel Bevel Dbl. Egress Metal Edge Guards/Astragal Metal Edge Guards Flat Astragal Glazing Options Standard Minimums All cutouts for metal or wood vision panels must be a minimum of 5 (152 mm) from the edge of the door and/or other cutouts for louvers, locks, closers or other hardware. Flush Mouldings* This 5 (152 mm) distance must be maintained or the fire label and warranty will be voided. For non-fire rated doors, the distance may be decreased to 5 (127 mm). Less than 5 (127 mm) may affect the warranty Using a 10 (254 mm) margin between the edge of the door and the edge of any cutout near the lock area will eliminate most label and warranty conflicts. Lip Mouldings** * A variance in the downset of flush mouldings may occur due to allowable tolerance deviations of components. ** Lip mouldings only are available for Thermal Fused Doors.
4 Wood Mouldings 3 GRAHAM Graham Maiman MAIMAN November, 2016 General Moulding Requirements Species shall match or be compatible with face veneer or laminate Moulding shall be free of open defects, shake, splits, or doze Moulding must be smooth and free of visible knife, saw or sanding marks 2 3 Lip Moulding for Lites 1. Matching specie to door face veneer for Premium grade. For use with 1-3/4 thick doors M2G - Flat Lip Moulding 15/16 wide x 5/8 thick, 3/32 radius. M3G - Beveled Lip Moulding 15/16 wide x 3/4 thick, 3/32 radius 2. Wire Brad - Lip Moulding is factory attached. 3. 1/4 Glazing - Glazing materials are not included. 4. Beveled back for glazing compound or 1/16 tape (not included). 5. Lites - Order size - visible glass size Cutout size = visible glass + (2 x moulding profile) Glass size = cutout - 1/4 wide - 1/4 high 1 4 3/32 15/16 3/32 15/16 3/8 5/8 1/2 3/4 11/16 11/16 M2G M3G Flush Moulding for Lites Matching specie to door face veneer for Premium grade. For use with 1-3/4 thick doors M6G - Flush Moulding 11/16 wide x 3/8 thick, 3/32 radius. 2. Wire Brad - Flush Moulding is factory attached. 3. 1/4 Glazing - Glazing materials are not included. 4. Beveled back for glazing compound or 1/16 tape (not included). 5. Lites - Order size - visible glass size Cutout size = visible glass + (2 x moulding profile) Glass size = cutout - 1/4 wide - 1/4 high 1 3/32 4 3/8 A variance in the downset of flush mouldings may occur due to allowable tolerance deviations of components. 11/16 M6G
5 4 GRAHAM Graham Maiman MAIMAN Wood Mouldings July, 2017 Fire Rated Flush Wood Moulding for Lites 1. Available with 45, 60 and 90 minute fire rated (mineral core) doors. Hourly Rating Area (in 2 ) Width (inch) Height (inch) Multiple Lites Distance from Lite Cutout to: Door Edge (inch) Hardware Prep Cutout (inch) Lite Cutouts (inch) Minute* Yes, sum of areas < 1296 in Factory installed: glass, glazing material, glazing bead, clips, nails, provided. 3. Flush Moulding Profile: MF3 4. Available Species: Red Oak, Natural Birch, White Maple, Cherry, Mahogany, and Walnut. Contact you Customer Service Professional for availability of other species. 5. Glass: 1/4 thick nominal wired glass (100 in 2 maximum) or 3/16 thick nominal ceramic (1296 in 2 maximum) 6. Cutout Size and Glass Size: Cutout Width = Visible Glass Width Cutout Height = Visible Glass Height Glass Width = Visible Glass Width Glass Height = Visible Glass Height /4 MF3 A variance in the downset of flush mouldings may occur due to allowable tolerance deviations of components. *The International Building Code (IBC) states that fire protection rated glazing in excess of 100 in 2 is not permitted in 60 and 90 minute fire rated doors. NFPA 80 states that glazing materials in vision panels shall be installed in accordance with inspection service procedure and under label service.
6 Louver Units 5 GRAHAM Graham Maiman MAIMAN V-Slat Wood Louver 3/32 3/32 11/16 7/16 M2W 3/8 7/16 M6 W 5/ /2 3/ L100 Wood Non-Vision Louver Unit - 3/4 wide, 33% free air movement. Matching specie to door face veneer for Premium grade. For use with 1-3/4 thick doors. Specify louver size the same as cutout size. 1-3/8 thick doors require framed louvers. Louvers may not be installed in 20 minute fire doors. M2W - Flat Lip Moulding 11/16 wide x 5/8 thick, 3/32 radius. M6W - Flush Moulding 7/16 wide x 3/8 thick, 3/32 radius 2. Wire Brad - Mouldings are factory attached. Louvers are not factory installed as standard. Louvers may be facorty installed as an option. 3. Field installation may require the use of glazing tape for proper fit. A variance in the downset of flush mouldings may occur due to allowable tolerance deviations of components. V-Slat Metal Louver 3/32 3/32 9/16 5/8 5/16 M2M 3/8 5/16 M6M 2 1 1/16 1/ L600 Metal Non-Vision Louver Unit - 1-1/16 wide, 20 gauge steel, 50% free air movement. For use with 1-3/4 thick doors. 1-3/8 thick doors require framed louvers. Louver cutout is 1/8 less then order size. Louvers may not be installed in 20 minute fire doors. M2M - Flat Lip Moulding 9/16 wide x 5/8 thick, 3/32 radius. M6M - Flush Moulding 5/16 wide x 3/8 thick, 3/32 radius 2. Wire Brad - Mouldings are factory attached. Louvers are not factory installed. Louvers may be facorty installed as an option. 3. Field installation may require the use of glazing tape for proper fit. A variance in the downset of flush mouldings may occur due to allowable tolerance deviations of components. Metal Fusible Link Louver L1900A Framed Metal Non-Vision Louver Unit - Fire rated fusible link unit for use with 45, 60 or 90 minute fire doors. 1-3/4 wide. 135 degree F fusible link. 40% free air movement. For use with 1-3/4 thick doors only. Not factory installed. Louvers may not be installed in 20 minute fire doors. 2. Steel mounting frame overlaps door face Through bolt applied. Security screws are available by option. 4. Metal fusible link louvers will not be factory installed.
7 6 GRAHAM Graham Maiman MAIMAN Vision Panels Fire rated Metal Vision Panel 1. M110 Metal Vision Frame - Fire rated for 20, 45, 60 and 90 minute fire door applications. 18 gauge steel with mitered, round corners that are braced and welded. Available wood veneer wrapped as an option. Low profile for hardware clearance. 2. Metal frame and glazing support clip. 3. Vandal proof binder screw. 4. For 1/4 thick listed glazing (not included). Note: No glazing compound or tape is required. Not factory installed. 5. Fire rated metal vision panels will be factory installed. 6. Lites - Order size = visible glass size Cutout size = visible glass size + 1-1/2 side + 1-1/2 high Glass size = visible glass size + 3/4 wide + 3/4 high 7. Listed for UL10b and UL10c Note: Custom shapes for specialty lites must be specified for visible glass size and cutout size. 20 Minute Moulding for Lites 1. Matching specie to door face veneer for Premium grade. For use with 1-3/4 thick 20 minute rated fire doors. M2L - Beveled Lip Moulding 1 wide x 3/4 thick. M2F - Beveled Flush Moulding 3/4 wide x 1/2 thick. 2. Metal glazing support clip. 3. Glazing compound or tape required for proper fit (not included). 4. For 1/4 thick listed glazing (not included). Size are visible glass size. Cutouts are 1 larger in width and height. Custom shapes for specialty lites must be specified for visible glass size and cutout size. 5. Lites - Order size = visible glass size Cutout size = visible glass size + (2 x moulding profile) Glass size = cutout - 1/4 wide - 1/4 high 6. Listed for UL10b and UL10c A variance in the downset of flush mouldings may occur due to allowable tolerance deviations of components. Note: Custom shapes for specialty lites must be specified for visible glass size and cutout size. 4 11/16 1/2 9/32 1/2 1/2 1 M2F M2L 1 3 2
8 Factory Installed Glass Architectural Accessories Detail 7 GRAHAM Graham Maiman MAIMAN KERALITE FILMED GLASS DESCRIPTION FIRE RATING MINUTE US TESTING LISTED AND LABELED WITH UNDERWRITERS LABORATORIES INC. FILE #R TESTED IN ACCORDANCE WITH UL 9, UL 10B, UL 10C, NFPA 80, NFPA 252, NFPA 257 CANADIAN TESTING CAN/ULC-S106, S104 IMPACT SAFETY RATING CPSC 16CFR PART 1201 (CATEGORIES I & II), ANSI Z97.1, CAN/CGSB-12.1-M NOMINAL THICKNESS 3/16 (5 MM) THICKNESS TOLERANCE +1/64 TO -1/64 (+0.4 MM TO -0.4 MM) U VALUE BTU/(HR*SQFT*DEGF) 0.88 WEIGHT (LBS/SQ FT.) 2.4 APPROX. VISIBLE LIGHT TRANSMISSION 86% RATING MAXIMUM EXPOSED AREA MAXIMUM WIDTH MAXIMUM HEIGHT 20, , CORE TYPE Mineral, Particleboard, Engineered Composite, Agrifiber Mineral, Particleboard, Engineered Composite 60* Mineral 60* Mineral 60, Mineral Temp Rise Mineral ** Glazing tape required for all fire rated applications KERALITE LAMINATED GLASS DESCRIPTION FIRE RATING MINUTE US TESTING LISTED AND LABELED WITH UNDERWRITERS LABORATORIES INC. FILE #R14515 TESTED IN ACCORDANCE WITH UL 9, UL 10B, UL 10C, NFPA 80, NFPA 252, NFPA 257 CANADIAN TESTING CAN/ULC-S106, S104 IMPACT SAFETY RATING CPSC 16CFR PART 1201 (CATEGORIES I & II). ANSI Z97.1, CAN/CGSB-12.1-M NOMINAL THICKNESS 5/16 (8 MM) THICKNESS TOLERANCE +1/64 TO -1/64 (+0.4 MM TO -0.4 MM) U VALUE BTU/(HR*SQFT*DEGF) 0.88 WEIGHT (LBS/SQ FT.) 4.1 APPROX. VISIBLE LIGHT TRANSMISSION 82% RATING MAXIMUM EXPOSED AREA MAXIMUM WIDTH MAXIMUM HEIGHT 20, , CORE TYPE Mineral, Particleboard, Engineered Composite, Agrifiber Mineral, Particleboard, Engineered Composite 60* Mineral 60* Mineral 60, Mineral Temp Rise Mineral ** Glazing tape required for all fire rated applications
9 8 GRAHAM Graham Maiman MAIMAN Factory Installed Glass FIRELITE NT (FIG05) Glass Description CERAMIC, FILMED FIRE AND SAFETY RATED GLASS BRAND: FIRELITE NT GRADE: PREMIUM THICKNESS: 3/16 NOMINAL WARRANTY: 3 YEAR LIMITED INCLUDES: GLAZING TAPE AND SETTING BLOCKS AS REQUIRED IMPACT SAFETY RATING: CPSC 16CFR1201, CAT I AND CAT II FIRE LISTINGS UL APPROVED, POSITIVE PRESSURE. GLASS IS MARKED IN ACCORDANCE WITH INTERNATIONAL BUILDING CODE SECTION AND 2406 NOTES RATING MAXIMUM EXPOSED AREA MAXIMUM WIDTH MAXIMUM HEIGHT 20, , CORE TYPE Mineral, Particleboard, Engineered Composite, Agrifiber Mineral, Particleboard, Engineered Composite 2 60* Mineral 2 60* Mineral 2 60, Mineral Temp Rise Mineral * 2 lites max 1 Same as above PEMKO FG Same as above PEMKO FG FIRELITE PLUS (FIG06) Glass Description CERAMIC, LAMINATED FIRE AND SAFETY RATED GLASS BRAND: FIRELITE PLUS GRADE: PREMIUM THICKNESS: 5/16 NOMINAL WARRANTY: 5 YEAR LIMITED INCLUDES: GLAZING TAPE AND SETTING BLOCKS AS REQUIRED IMPACT SAFETY RATING: CPSC 16CFR1201, CAT I AND CAT II FIRE LISTINGS UL APPROVED, POSITIVE PRESSURE. GLASS IS MARKED IN ACCORDANCE WITH INTERNATIONAL BUILDING CODE SECTION AND 2406 NOTES RATING MAXIMUM EXPOSED AREA MAXIMUM WIDTH MAXIMUM HEIGHT 20, , CORE TYPE Mineral, Particleboard, Engineered Composite, Agrifiber Mineral, Particleboard, Engineered Composite 2 60* Mineral 2 60* Mineral 2 60, Mineral Temp Rise Mineral * 2 lites max 1 Same as above PEMKO FG Same as above PEMKO FG
10 Factory Installed Glass Architectural Accessories Detail 9 GRAHAM Graham Maiman MAIMAN 1/4 TEMPERED (FIG01) Glass Description 1/4 CLEAR TEMPERED IMPACT SAFETY RATED GLASS QUALITY RATING: Q3, ASTM C THICKNESS: 1/4 NOMINAL WARRANTY: 1 YEAR LIMITED INCLUDES: GLAZING TAPE AND SETTING BLOCKS AS REQUIRED IMPACT SAFETY RATING: CPSC 16CFR1201, CAT I AND CAT II GLASS IS MARKED IN ACCORDANCE WITH INTERNATIONAL BUILDING CODE SECTION 2406 NOT FOR USE ON FIRE RATED DOORS 1/4 FILMED WIRE (FIG02) Glass Description 1/4 FILM WIRE, FIRE AND IMPACT SAFETY RATED GLASS QUALITY RATING: Q3, ASTM C THICKNESS: 1/4 NOMINAL WARRANTY: 1 YEAR LIMITED INCLUDES: GLAZING TAPE AND SETTING BLOCKS AS REQUIRED IMPACT SAFETY RATING: CPSC 16CFR1201, CAT I AND CAT II FIRE LISTINGS UL AND INTERTEK/WARNOCK- HERSEY APPROVED, POSITIVE PRESSURE. GLASS IS MARKED IN ACCORDANCE WITH INTERNATIONAL BUILDING CODE SECTION AND 2406 RATING MAXIMUM EXPOSED AREA MAXIMUM WIDTH MAXIMUM HEIGHT 20, CORE TYPE Mineral, Particleboard, Engineered Composite, Agrifiber 60, 90 * Mineral Temp Rise Mineral * Non Temp Rise
11 10 GRAHAM Graham Maiman MAIMAN Astragals/Edges Flat Wood Astragal 1. A1 Wood Astragal - 2 wide, 1/2 thick, 1/4 radius on face edges. Matching specie to door face veneer for Premium grade. For use with 1-3/4 or 1-3/8 thick doors. 2. May be applied using wood screws and adhesive. 3. Not for use on any 45, 60 or 90 minute fire rated doors. Flat wood astragals may be applied to 20 minute neutral pressure tested pairs with Firestop metting edges. 1 Metal Astragal & Edge 1. M207. metal Edge Set With Overlapping Astragal - 16 gauge welded astragal overlaps meeting edge 1. Approved for 20, 45, 60 and 90 minute fire door applications. Available wood veneer wrapped as an option. May be specified unmachined or machined for builders hardware gauge wrap-around metal edge overpals meeting stile Phillips Flat head Screws - #8 x 3/4 12 on center (included). 3 Note: Overlapping astragals are no longer required for fire rated pairs. 1 2 Double Metal Edge 1. M208 Double Metal Edge Set - 20 gauge wrap-around metal edge overlaps metting stiles of doors 1. Approved for 20, 45, 60 and 90 minute fire door applications. Available wood veneer wrapped as an option. may be specified unmachined or machined for builders hardware. 2. Phillips Flat head Screws - #8 x 3/4, 12 on center (included). Note: Double metal edges are no longer required on 20, 45, 60 or 90 minute paris if doors are specified to be without metal edges. Requires special interior blocking profiles. 3. Also available with 5 wrap-around metal edges for use with the application of concealed vertical rod exit devices in the M250 series. 2 1
12 Dutch Door (Non Fire Rated) Architectural Accessories Detail 11 GRAHAM Graham Maiman MAIMAN Height By Specification General Notes 1. Allow for shelf thickness when specifying hardware. 2. Standard shelf is (28 mm) thick wood, 1 side only. 3. Standard wood shelf sits between leaves. 4. Shelf and supports are not factory installed 5. Note if shelf is not required. 6. Note if other than standard shelf is required. 7. Dutch doors are available in GPD or GCD bonded consturction only. 8. GPD has matching bottom rail in top leaf. GCD has non-matching bottom rail in top leaf. 9. Dutch doors are available in single openings up to 4 0 x 9 0. Dutch doors are available in paired openings up to 8 0 x /16 Height By Specification (includes shelf) 8 1-3/4 Shelf 4 1-1/8 4 Shelf Bracket
13 12 GRAHAM Graham Maiman MAIMAN Dutch Door (Non Fire Rated) General Notes 1. Dutch doors may be provided with: a. Straight cut metting edges of top and bottom leaf. b. Rabbeted metting edges of top and bottom leaf. 2. Standard clearnace between top leaf and bottom leaf of Dutch doors is 3/ Dutch door latching may be cylindrical, mortise or flushbolt latches that latch: a. top leaf into bottom leaf, bottom leaf into frame. b. top leaf into bottom leaf, top leaf into frame. c. top leaf into frame, bottom leaf into frame. NON RATED DUTCH DOOR TOP LEAF 2 Wood Rails (Min.) 1-1/8 Wood Shelf 2 Wood Rails (Min.) BOTTOM LEAF EXAMPLE OF LATCHING CONFIGURATION TOP LEAF TOP LEAF ACTIVE LEAF INACTIVE LEAF BOTTOM LEAF BOTTOM LEAF PAIR OF DUTCH DOORS
14 Dutch Door (20 Minute Fire Rating) Architectural Accessories Detail 13 GRAHAM Graham Maiman MAIMAN Height By Specification 1/8 General Notes 1. Allow for shelf thickness when specifying hardware. 2. Standard shelf is (28 mm) thick wood, 1 side only. 3. Standard wood shelf sits between leaves. 4. Shelf and supports are not factory installed 5. Note if shelf is not required. 6. Note if other than standard shelf is required. 7. Dutch doors are available in GPD or GCD bonded consturction only. 8. GPD has Firestop bottom rail in top leaf. Firestop top rail in bottom leaf. GCD has Firestop bottom rail in top leaf, Firestop top rail in bottom leaf. 9. Dutch doors are not available in 90 minute neutral pressure tested construction. 10. Positive pressure fire tested Dutch door constructions are not available. 11. Dutch doors are available in 20 minute fire rated single openings up to 4 0 x Dutch doors are available in 20 minute fire rated paired openings up to 8 0 x 8 0. Height By Specification (includes shelf) 8 1-3/4 Shelf 1-1/8 4 4 Shelf Bracket
15 14 GRAHAM Graham Maiman MAIMAN Dutch Door (20 Minute Fire Rating) General Notes minute Dutch doors may be provided with one of these: a. An overlapping astragal applied to the bottom rail of the top leaf b. Intumescent fire seal installed in the bottom rail of the top leaf. c. Standard wood shelf sits between leaves. 2. A maximum 1/8 (3.2 mm) clearance between top leaf and bottom leaf of fire rated Dutch doors is allowed. 3. Fire rated Dutch doors require both leaves to be self latching. Leaf to leaf or leaf to frame. 4. Fire rated Dutch door latching is limited to cylindrical or mortise latches that latch: a. top leaf into bottom leaf, bottom leaf into frame. b. top leaf into bottom leaf, top leaf into frame. c. top leaf into frame, bottom leaf into frame. 5. Flushbolts are allowed on the inactive leaves of a pair. 20 MINUTE DUTCH DOOR TOP LEAF 2 wide Firestop Rails (Min.) Intumescent 1-1/8 Wood Shelf 2 wide Firestop Rails (Min.) BOTTOM LEAF EXAMPLE OF LATCHING CONFIGURATION TOP LEAF TOP LEAF ACTIVE LEAF INACTIVE LEAF BOTTOM LEAF BOTTOM LEAF PAIR OF DUTCH DOORS
16 Dutch Door (45/60 Minute Fire Rated) Architectural Accessories Detail 15 GRAHAM Graham Maiman MAIMAN Height By Specification 1/8 General Notes 1. Allow for shelf thickness when specifying hardware. 2. Standard shelf is (28 mm) thick wood, 1 side only. 3. Standard wood shelf butts to face of bottom leaf. 4. Shelf and supports are not factory installed 5. Note if shelf is not required. 6. Note if other than standard shelf is required. 7. Dutch doors are available in GPD or GCD bonded consturction only. 8. GPD has Firestop bottom rail in top leaf. Firestop top rail in bottom leaf. GCD has Firestop bottom rail in top leaf, Firestop top rail in bottom leaf. 9. Dutch doors are not available in 90 minute neutral pressure tested construction. 10. Positive pressure fire tested Dutch door constructions are not available. 11. Dutch doors are available in 45/60 minute fire rated single openings up to 4 0 x Dutch doors are not available in 45/60 minute fire rated paired openings. Height By Specification (includes shelf) 8 1-3/4 Shelf 1-1/8 4 4 Shelf Bracket
17 16 GRAHAM Graham Maiman MAIMAN Dutch Door (45/60 Minute Fire Rated) General Notes 1. 45/60 minute Dutch doors may be provided with one of these: a. An overlapping astragal applied to the bottom rail of the top leaf b. Intumescent fire seal installed in the bottom rail of the top leaf. c. Standard wood shelf sits between leaves. 2. A maximum 1/8 (3.2 mm) clearance between top leaf and bottom leaf of fire rated Dutch doors is allowed. 3. Fire rated Dutch doors require both leaves to be self latching. Leaf to leaf or leaf to frame. 4. Fire rated Dutch door latching is limited to cylindrical or mortise latches that latch: a. top leaf into bottom leaf, bottom leaf into frame. b. top leaf into bottom leaf, top leaf into frame. c. top leaf into frame, bottom leaf into frame. 45/60 MINUTE DUTCH DOOR TOP LEAF 2 wide Firestop Rails (Min.) Intumescent 1-1/8 Wood Shelf 2 wide Firestop Rails (Min.) BOTTOM LEAF EXAMPLE OF LATCHING CONFIGURATION TOP LEAF TOP LEAF BOTTOM LEAF BOTTOM LEAF
18 Doors with Transoms (Non-Rated) Architectural Accessories Detail 17 GRAHAM Graham Maiman MAIMAN November, 2016 Non-rated Doors with Transoms 1. Doors with transoms are available with or without frame transom bars in single or paired openings. 2. Meeting edges of transoms and doors in openings without transom bars may be straight cut or rabbeted. See standard rabbet detail. 3. Doors with transoms are available in GPD and GCD bonded constructions only. 4. GPD has matching rails at bottom of transom and top of door. GCD has 5. non-matching rails at bottom of transom and top of door. 6. Spring bolts are required for installation of transom panels. To receive lifetime warranty on doors and transoms, springbolts must be placed a minimum of 2 (51 mm) from each corner. Panels up to 18 (458 mm) in height require 2 springbolts per side. Panels up to 36 (916 mm) in height require 3 springbolts per side. Panels up to 40 (1220 mm) in height require 4 springbolts per side. 7. Doors with transoms are available in single openings up to 4 0 x Maximum transom panel size in a single opening up to 4 0 wide x 3 4 high. Doors with transoms are available in paired openings up to 8 0 x Maximum transom panel size is a paired opening is 8 0 wide x 3 4 high.
19 18 GRAHAM Graham Maiman MAIMAN Doors with Transoms (Non-Rated) November, 2016 NON RATED DOOR WITH TRANSOM Solid Wood Cores Transom 1 Wood Rails 1/8 Max. Gap 1 Wood Rails 1/8 Max. Gap Steel Astragals Optional Solid Wood Cores 1-3/4 1-3/4 DOOR WITH TRANSOM IN FRAME WITH MULLION Non-Rated Doors with Transoms Transom 1 Wood Rails Mullion 1. Doors with transom may be provided with: a. Straight cut meeting edges of door and transom with an over lapping astragal optional. b. Straight cut meeting edges of door and transom with frame transom bar. c. Rabbeted meeting edges of door and transom. 2. A maximum 1/8 (3.2 mm) clearance between door and transom is allowed in non-rabbeted applications. 3. Transom panels must be installed using springbolts placed a minimum of 2 (51 mm) from each corner. 1 Wood Rails
20 Door with Transom (20 Minute Fire Rated) Architectural Accessories Detail 19 GRAHAM Graham Maiman MAIMAN 20 Minute Fire Rated Doors with Transoms 1. Transom panels must be the same construction as the 20 minute fire door. 2. Neutral pressure tested doors with transom panels may be rabbeted, or installed with a metal edge and astragal, or with a transom bar between the door and transom. Positive pressure tested doors with transom panels must be installed in a frame with a transom bar between the door and transom. 3. Transom installed over a pair of 20 minute rated doors must be separated with a frame mullion. The mullion must limit the width of each separate transom to the width of each leaf of the door pair. 4. The transom panel must be machined for spring bolts by the licensed machiner of manufacturer. The appropriate number of springbolts will be supplied by the machiner. 5. Fire rating labels will be provided on door and transom stating Door and Transom Assembly. 6. Fire rated transom panels must be installed using approved steel springbolts. The springbolts shall be placed 2 (51 mm) from each corner with the minimum number centered on each side. Holes must be drilled in the frame to accept the springbolts. Hole locations vary with respect to rabbeted and unrabbeted tansoms. Panels up to 18 (458 mm) in height require 2 springbolts per side. Panels up to 36 (916 mm) in height require 3 springbolts per side. Panels up to 40 (1220 mm) in height require 4 springbolts per side. 7. Maximum clearance between the frame and panel must be 1/8 (3.2 mm). 8. Doors with transoms are available in single openings up to 4 0 x Maximum transom panel size in a single opening up to 4 0 wide x 3 4 high. Doors with transoms are available in paired openings up to 8 0 x Maximum transom panel size is a paired opening is 8 0 wide x 3 4 high. Transom panels above pairs of doors must be separated by a mullion.
21 20 GRAHAM Graham Maiman MAIMAN Door with Transom (20 Minute Fire Rated) Solid Wood Cores Transom 1/8 Max. Gap 1 Wide Firestop Rails Min. 1 Wide Firestop Rails Min. 1/8 Max. Gap Steel Astragals Solid Wood Cores 1-3/4 20 Minute Doors with Transoms 1. Neutral pressure tested fire doors with transoms may be provided with: a. Straight cut meeting edges of door and transom with an over lapping astragal. b. Straight cut metting edges of door and transom with frame transom bar. c. Rabbeted meeting edges of door and transom. Positive pressure tesed fire doors with transoms must be installed in a frame with transom bar between the door and transom. 2. A maximum 1/8 (3.2 mm) clearance between door and transom is allowed in non-rabbeted applications. Maximum clearance between the frame and transom panel must be 1/8 (3.2 mm). 3. Fire rated Transom panels must be installed using approved steel springbolts. The springbolts shall be placed 2 (51 mm) from each corner with the minimum number centered on each side. Holes must be drilled in the frame to accept the springbolts. Hole locations vary with respect to rabbeted and unrabbeted transoms. Panels up to 18 (458 mm) in height require 2 springbolts per side. Panels up to 36 (916 mm) in height require 3 springbolts per side. Panels up to 40 (1220 mm) in height require 4 springbolts per side. 1-3/4 20 MINUTE DOOR WITH TRANSOM IN FRAME WITH MULLION Transom 1 Wide Firestop Rails Min. Mullion 1 Wide Firestop Rails Min.
22 45/60/90 Minute Fire Rated Doors with Transoms Architectural Accessories Detail 21 GRAHAM Graham Maiman MAIMAN 45/60/90 Minute Fire Rated Doors with Transoms 1. Transom panels must be the same construction as the 20 minute fire door. 2. Neutral pressure tested doors with transom panels may be rabbeted, or installed with a metal edge and astragal, or with a transom bar between the door and transom. Rabbeted door and transom assemblies must be constructed with minimum 5 (127 mm) Firestop bottom rail of transom and top rail of door. The rabbet must be a minimum 1/2 (13 mm) deep x 7/8 (22 mm) wide. Positive pressure tested doors with transom panels must be installed in a frame with a transom bar between the door and transom. 3. If an overhead door closer is to be installed the bottom rail of the transom and the top rail of the door must be 5 (127 mm) Firestop. When transom bar is provided the rails shall be standard Firestop or Firestop II material. 4. Transom installed over a pair of fire rated doors must be separated with a frame mullion. The mullion must limit the width of each separate transom to the width of each leaf of the door pair. 5. The transom panel must be machined for spring bolts by the licensed machiner of manufacturer. The appropriate number of springbolts will be supplied by the machiner. 6. Fire rating labels will be provided on door and transom stating Door and Transom Assembly. 7. Fire rated transom panels must be installed using approved steel springbolts. The springbolts shall be placed 2 (51 mm) from each corner with the minimum number centered on each side. Holes must be drilled in the frame to accept the springbolts. Panels up to 18 (458 mm) in height require 2 springbolts per side. Panels up to 36 (916 mm) in height require 3 springbolts per side. Panels up to 40 (1220 mm) in height require 4 springbolts per side. Maximum clearance between the frame and panel must be 1/8 (3.2 mm). 8. Neutral pressure tested fire doors with transoms are available in single openings up to 4 0 x Positive pressure tested fire doors with transoms are available in single openings up to 4 0 x 9 0. Neutral pressure tested fire doors with transoms are available in paired openings up to 8 0 x Positive pressure tested fire doors with transoms are available in paired openings up to 8 0 x 9 0. Maximum transom panel size in a single opening up to 4 0 wide x 3 4 high. Maximum transom panel size in a paired opening is 4 0 wide x 3 4 high. Transom panels above pairs of doors must be separated by a mullion.
23 22 GRAHAM Graham Maiman MAIMAN Doors with Tramsoms (45/60/90 Minute Fire Rated) Transom 5 Wide Firestop Rails Min. 1/8 Max. Gap 5 Wide Firestop Rails Min. 1/8 Max. Gap Steel Astragals 1-3/4 1-3/4 45/60/90 Minute Doors with Transoms 1. Neutral pressure tested fire doors with transoms may be provided with: a. Straight cut meeting edges of door and transom with an over lapping astragal. b. Straight cut metting edges of door and transom with frame transom bar. c. Rabbeted meeting edges of door and transom. Rabbeted meeting edges require 5 (127 mm) bottom rail of tramson and top rail of door. Positive pressure tesed fire doors with transoms must be installed in a frame with transom bar between the door and transom. 2. A maximum 1/8 (3.2 mm) clearance between door and transom is allowed in non-rabbeted applications. Maximum clearance between the frame and transom panel must be 1/8 (3.2 mm). 3. Fire rated Transom panels must be installed using approved steel springbolts. The springbolts shall be placed 2 (51 mm) from each corner with the minimum number centered on each side. Holes must be drilled in the frame to accept the springbolts. Hole locations vary with respect to rabbeted and unrabbeted transoms. Panels up to 18 (458 mm) in height require 2 springbolts per side. Panels up to 36 (916 mm) in height require 3 springbolts per side. Panels up to 40 (1220 mm) in height require 4 springbolts per side. 45/60/90 MINUTE DOOR WITH TRANSOM IN FRAME WITH MULLION Transom G-P Firestop Composition 1 Wide Firestop Rails Min. Mullion G-P Firestop Composition 1 Wide Firestop Rails Min.
24 Wicket Doors (Standard) Architectural Accessories Detail 23 GRAHAM Graham Maiman MAIMAN General Notes 1. Requires handing of call door and wicket door 2. Latch/lock for call door must be suitable for rabbeted application 3. Shelf and call door are not factory installed 4. Available in GPD or GCD bonded constructions only 5. SCLC (EC) core required Call Door Hinged Side Unrabbeted Rabbeted Shelf 3/32 Reveal Wicket Door 1-1/8 Thick Shelf 1-3/4 8 13/16 9/16 Shelf 2 Call Door Size Opening Size /4 Typical Rabbet Shelf Bracket
25 24 GRAHAM Graham Maiman MAIMAN Special Machining General Notes Standard Rabbet 1. Provide non-vision joint between door and transom. 2. Non-fire rated wood core door/transom units hae solid matching hardwood top rail in door and bottom rail in transom. 3. Rabbets allow 1/8 spacing between door and transom when door is in closed position. 4. Available on 20-minute rated doors/transoms. 5. May be applied to 45, 60 and 90-minute fire doors. Mineral core fire door/transom units do not have matching rails. requires special construction. 6. Available on 1-3/4 thick doors only. 7. Available in GPD or GCD bonded constructions only. Note: GPD has matching bottom rail on top leaf and matching top rail on bottom leaf. GCD has non-matching bottom rail on top leaf and non-matching top rail on bottom leaf. General Notes Transom 1. Used on doors when specified using pivot hinges or when double acting door is specified. 2. When specified for application to lock stile, verify lock/latch hardware compatibility. Requires full face stile. 3. When specified for application to hinge stile, verify radius of edge with hardware template requirements. 4. Available on 1-3/4 thick doors only. 5. Available in GPD or GCD bonded constructions only. 6. Not available on any fire rated door. 7. Specify radius on hinge and lock edge. Radius Edge Door Available Radii (R) Convex Concave 2-1/2 1-7/8 1-1/2 1-5/32 1-5/32
26 Flush Bolts Architectural Accessories Detail 25 GRAHAM Graham Maiman MAIMAN May, 2017 Corner mounted flush bolts having mortised cutouts greater than 3/4" wide and 1" deep have a tendency to flare out (flushbolt flare). Flare-out of door corners and any functional problems resulting from hardware preparations requiring removal of core material at door corners is not considered a manufacturing defect under the manufacturer warranty. Delamination or breakage due to mishandling at the corner is common and is not considered a manufacturing defect. If this type of flush bolt is required, ASSA ABLOY requires the use of one of the following to maintain warranty on the door. a. Flush bolt end caps, supplied by others (see detail). End caps are not provided by ASSA ABLOY. b. Astragal/edge set (must be specified on order). Flush bolt end cap. End cap fits over the top rail so the bolt can protrude through the hole. Top flush bolt on mineral core doors: Corner mount flush bolts required on fire rated doors must be used in conjunction with manufacture s required fire listing approvals for use in wood doors. Flush bolts not intended for use in wood doors will not be covered under manufacture warranty. Typical flaring problem with corner mount auto flush bolt requiring complete removal of core at corner. Cutout Edge View Flush Bolt Cutout Top View
27 26 GRAHAM Graham Maiman MAIMAN Fire Door Plant-Ons Architectural Accessories Detail May, 2017 General Notes Minimum spacing to edge of door or cutout. Minimum spacing between plant-ons. Decorative Door Plant-ons are allowed on 20, 45, 60 and 90 minute labeled fire doors. The following conditions apply: 1. Type, size and configuration are limited by the door manufacturer s tested authorities. 2. The plant-ons must be applied under label service at factory or qulaified distributor. Plant-ons may not be field applied to fire rated doors. Standard Profiles Offered 1. ASSA ABLOY offers the following profiles. Customers may supply assembled plant-ons in other species and profiles, provided they meet the specifications for the intended use listed below. These may also be used on non-fire rated doors. 9/16 3/4 Minimum enclosed area. Twice the profile width for width of area.. 1-1/2 P-7 5/8 1-1/2 P-8 Specifications 20 Minute GP 45/60 Minute GP 90 Minute Max. Profile Width: 1-3/4 2-1/2 2-1/2 Max. Profile Height 3/4 3/4 3/4 Wood Specie Douglas Fir or Denser Same Same Attachment Adhesive or Mechanical Adhesive or mechanical Adhesive Spacing: to edge of door or cutout 2-3/8 P Between Plant-ons Equal or Greater than Profile Same Same Min. Enclosed Area N/A 2 Time Profile Width & Height 2 Time Profile Width & Height Coverage Mouldings may not cover in excess of 20% of door face. Mouldings may not cover in excess of 22% of door face. Mouldings may not cover in excess of 22% of door face.
28 Full Glass/Full Warranty Door 27 GRAHAM Graham Maiman MAIMAN October, " 6" Maximum Size: Thickness: Series: Core: Rating: Visible Size: Glass Thickness: Mouldings: Glazing Material: Moulding Installation: Warranty: 4 0 wide x 9 0 high 1-3/4 only GPD, GCD Wood based particle core Non-rated or 20 min. only. Fire rated must follow fire listing requirements for glass size and lite/lock conflicts Minimum 8 top rail to visible glass Minimum 6 lock stile and hinge stile to visible glass Minimum 12 bottom rail to visible glass Maximum 1/4" glass only M2G (lip), M3G (beveled lip), M6G (flush), M2F (20 min. flush), M2L (20 min. lip), MVP. All moulding is sized for installation with 1/4 glass. Only factory installed glass will have factory installed moulding. Factory installed moulding will have nail holes filled. If not factory installed, moulding will ship loose; nail holes will not be filled Per project specification 12" For non-rated wood doors, moulding must be installed using 3/32 glazing tape on both sides of the glass and must be fastened every 8 on center using 3d finishing nails (glazing tape and finish nails not provided). For fire rated applications, follow the installation instructions for the listed and labeled lite kit Not warranted for exterior applications or applications which expose a door to extremes of temperature and/or humidity regardless of the physical placement
29 28 GRAHAM Graham Maiman MAIMAN ElectroLynx System Architectural Accessories Detail THE GRAHAM ELECTROLYNX CABLE IS EQUIPPED WITH THE ELECTROLYNX SYSTEM OF PLUG IN CONNECTORS FOR FAST, EASY, CONNECTION TO SIMILARLY EQUIPPED ASSAABLOY HARDWARE. THE ELECTROLYNX CABLE HAS 12 CONDUCTORS OF 22 GA. WIFRE, WITH ELECTROLYNX CONNECTORS. POWER OVER ETHERNET (POE) IS AVAILABLE IF REQUIRED. AVAILABLE IN GPD & GCD DOORS ONLY SINGLE CABLE LOCK EDGE VERIFY CABLE LOCATION BEFORE MODIFYING DOOR OR SURFACE APPLICATION OF HARDWARE. 3/8 HINGE EDGE 3 HINGE DOOR SINGLE CABLE 4 HINGE DOOR MULTIPLE CABLE 5 HINGE DOOR C L ELECTRIC HINGE LOCATION HARDWARE LOCATION *ELECTRIC HINGE LOCATION ELECTRIC HINGE LOCATION ELECTRIC HINGE LOCATION MULTIPLE CABLE* LOCK EDGE HINGE EDGE ELECTRIC HINGE LOCATION ELECTRIFIED TRIM 3/8 FIRE STOP BLOCKING OR WIDER FIRE STOP STILE DEPENDING ON HARDWARE REQUIREMENTS *DOOR MUST BE PREPPED WITH A MINIMUM OF 4 HINGES *THE ELECTROLYNX HINGE WILL ALWAYS BE LOCATED IN THE SECOND HINGE FROM THE FLOOR MAXIMUM OF TWO RACEWAYS PER DOOR ON FIRE-RATED DOORS. CAN BE USED IN BOTH NEUTRAL & POSITIVE PRESSURE DOORS CATEGORY A & B
30 Door Glazing Chart 29 GRAHAM Graham Maiman MAIMAN November, 2017 General Notes: All glass must be fire rated and safety impact rated. Fire Rating (Minutes) 1/4 Filmed Wire Lite Kit Max Size (in 2 ) Max Width (Inches) Max Length (Inches) Temp Rise No 20 Wood No No Agrifiber and Mineral core only. 45 MF No Universal (LDF) core only No Yes 60 MF No Universal (LDF) core only No No 90 MF No Universal (LDF) core only. 3/16 Firelite NT, 5/16 Firelite Plus, 3/16 Vetrotech Standard Film, 5/16 Vetrotech Standard Film * No * No * No Agrifiber and Mineral core only. Notes Maximum 4090 door. Must use Pemko FG3000S45 Glazing Tape. Not allowed on Agrifiber core doors * No Maximum 4090 door. Must use Pemko FG3000S45 Glazing Tape. Mineral core only. 45 Wood 1080* No Response Engineered core only. 45 MF3 1296* No Universal (LDF) core only No Yes * No Maximum 4090 door. Must use Pemko FG3000S90 Glazing Tape * No Maximum 4090 door. Must use Pemko FG3000S90 Glazing Tape. (Two light maximum, 960 in2 each, 12 maximum width). 60 MF3 1296* No Universal (LDF) core only No Yes * No Maximum 4090 door. Must use Pemko FG3000S90 Glazing Tape. 90 MF3 1296* No Universal (LDF) core only. * Multiple Lites Allowed
31 30 GRAHAM Graham Maiman MAIMAN Door Glazing Chart November, 2017 General Notes: All glass must be fire rated and safety impact rated. Fire Rating (Minutes) Lite Kit 3/16" Pyran Platinum F Max Size (in 2 ) Max Width (Inches) Max Length (Inches) Temp Rise Notes * No 20 Wood 1296* No Maximum 4090 door. Must use Pemko FG3000S45 Glazing Tape. Not allowed on Agrifiber core doors * No Agrifiber and Mineral core only * No Maximum 4090 door. Must use Pemko FG3000S45 Glazing Tape. Mineral core only. 45 MF3 1296* No Universal (LDF) core only No Yes * No Maximum 4090 door. Must use Pemko FG3000S90 Glazing Tape * No Maximum 4090 door. Must use Pemko FG300S90 Glazing Tape. (Two light maximum, 900 in2 each, 12" maximum width). 60 MF No Universal (LDF) core only No Yes * No Maximum 4090 door. Must use Pemko FG3000S90 Glazing Tape. 90 MF3 1296* No Universal (LDF) core only. 3/8" Pyran Platinum L No * No Maximum 4090 door. Must use Pemko FG3000S45 Glazing Tape. Not allowed on Agrifiber core doors No Agrifiber and Mineral core only * No Maximum 4090 door. Must use Pemko FG3000S45 Glazing Tape. Mineral core only No Yes * No Maximum 4090 door. Must use Pemko FG3000S90 Glazing Tape * No Maximum 4090 door. Must use Pemko FG3000S90. Glazing Tape. (Two light maximum, 960 in2 each, 12 maximum width) No Yes * No Maximum 4090 door. Must use Pemko FG3000S90 Glazing Tape. * Multiple Lites Allowed
32 Door Glazing Chart 31 GRAHAM Graham Maiman MAIMAN November, 2017 Core Rating (Minutes) Minimum Light/Lock Distance Maximum Light/Lock Distance Minimum Light/Door Edge Particleboard (PC) None 1-1/2" 3-5/16" 5" Particleboard (PC) /2" 4" 4" Agrifiber (AF) /2" 4" 4" Lead Line (LE) None 1-1/2" 3-5/16" 5" Lead Line (LL) /2" 5" 5" Agrifiber (AF) 45 4" 4" 4" Engineered (EC) None 1-1/2" 3-5/16" 5" Engineered (EC) /2" 4" 4" Response Engineered (RC) 45 4" 4" 4" G.P. White Mineral (FD) " 5" 5" G.P. Blue Mineral (BC) " 5" 5" G.P. LDF (FD) /16" 5" 5"
33 32 GRAHAM Graham Maiman MAIMAN Wood Frames Architectural Accessories Detail ASSA ABLOY offers a complete line of non-rated frames to compliment our fire-rated frames. All of our frames feature the same high quality craftsmanship as our stile and rail doors and will match them beautifully. We use the same veneer and finishing products on both doors and frames, regardless of fire-rating. Over the last 35 years we have found flat jambs to be the most economical, environmentally responsible, and highest quality in appearance and construction. Flat jambs are a much more stable product than other types of jambs, and the veneered frame will be of superior face materials. We produce flat jambs with the door stops constructed of solid lumber: long, loose, and unmitered to be applied in the field. This allows for a perfect fit when the door is hung and latched. The frames themselves will be a veneered construction with the exception of Paint Grade jambs which may be solid lumber. The 1/16 veneer used on the stiles and rails of our doors is the same 1/16 veneer we use on our frames. These frames can also be used for sidelights or transoms. Non-Rated Stain Grade Flat Jamb Standard jamb thickness is 13/16 and standard door stop size is 5/8 x 1-1/2 as shown in the standard construction drawing above. We can also produce custom frames in other dimensions with few restrictions for non-rated jambs. Note on Rabbetted Jambs ASSA ABLOY also offers non-rated rabbetted jambs, in both single and double rabbet. However, for continuity of products as well as conservation of resources, We HIGHLY RECOMMEND that a flat jamb with a wider door stop (as necessary) be used in lieu of solid lumber rabbetted jambs. Fire-Rated rabbetted jambs are not available.
34 Wood Frames Architectural Accessories Detail 33 GRAHAM Graham Maiman MAIMAN 20-Minute Fire-Rated Flat Jamb Neutral and Positive Pressure Categories A & B Max. single frame size 4-0 x 9-0 Max. paired frame size 8-0 x 9-0 Wood species W. Pine or denser Min. wall thickness 3.75 Min. stop height.625 Min. stop width 1.5 Min. casing size wide x.375 Casing wood species Any 4-sided sidelite frames 3-0 x sided transom frames 8-0 x 3-0 Borrowed sidelite frames 1-6 x 7-0 Borrowed transom frames N/A Wall types Steel, wood stud, or masonry 20 Minute Stain Grade Flat Jamb
35 34 GRAHAM Graham Maiman MAIMAN Wood Frame 45 and 60 Minute Wood Frame Specifications Neutral and Positive Pressure Categories A & B Neutral Pressure Max. single frame size 4-0 x x 9-0 Max. paired frame size 8-0 x x 9-0 Wood species Any Any Min. wall thickness Min. stop height Min. stop width 1 (1.5 standard) 1.5 Positive Pressure Min. casing size wide x wide x.313 Wall types Steel stud, wood stud, or masonry Steel stud, wood stud, or masonry 90 Minute Wood Frame Specifications Neutral and Positive Pressure Categories A & B Neutral Pressure Max. single frame size 4-0 x x 8-0 Max. paired frame size 8-0 x 8-0 Pending Wood species Any Any Min. wall thickness Min. stop height Min. stop width 1 (1.5 standard) 1.5 Positive Pressure Min. casing size wide x wide x.313 Wall types Steel stud, wood stud, or masonry Steel stud, wood stud, or masonry
36 Wood Frame Architectural Accessories Detail 35 GRAHAM Graham Maiman MAIMAN 45, 60, and 90 Minute Jambs Neutral and Positive Pressure Categories A & B (Category B shown below)
Infinity 20 Min. FIRE RATED DOORS WARNOCK HERSEY INFINITY - STANDARD RAISED - 20 MIN. RATING SOFTWOOD STILE
Infinity 20 Min Note: 20 Minute (Positive Pressure) Category A & B Manufacturing Specifications MAXIMUM SIZES All doors shall have a minimum thickness of 1-3/4" + 1/16" Single Swing: 4/0 x 9/0 Standard
More informationFIRE RATED DOOR AND FRAME GENERAL REQUIREMENTS
FIRE RATED DOOR AND FRAME GENERAL REQUIREMENTS These requirements apply to all fire rated doors, frames, and windows. Requirements for the installation of these assemblies are included in the Standard
More informationFIRE RATED DOOR AND FRAME GENERAL REQUIREMENTS
` FIRE RATED DOOR AND FRAME GENERAL REQUIREMENTS These requirements apply to all fire rated doors, frames, and windows. Requirements for the installation of these assemblies are included in the Standard
More informationEncore 20 Min. FIRE RATED DOORS WARNOCK HERSEY ENCORE - STANDARD PANEL - 20 MIN. RATING
Encore 20 Min 20 Minute (Positive Pressure) - Category B Manufacturing Specifications MAXIMUM SIZES All doors shall have a minimum thickness of 1-3/4" + 1/16" Single Swing: 4/0 x 8/0 Standard Pair: 8/0
More informationACCESSORIES. Factory-Installed Glazing
ACCESSORIES Affordable Options from VT With options such as factory-installed glazing, applied mouldings and factory-installed louvers available from VT Industries, you can achieve the look you want with
More information20 Minute Rated Barrier Resistant (BR SCL5-20PP) Bonded SCL Core, 5-Ply Construction, Cat. A, PP
20 Minute Rated Barrier Resistant (BR SCL5-20PP) Bonded SCL Core, 5-Ply Construction, Cat. A, PP (Fire Test Standards IBC, UL-10C, CAN/ULC S104, & NFPA 252) Single Swing ONLY Core Type & Standards Structural
More information45 Minute Rated Mineral STC35/34 (FD5-45PP STC 35/34) Bonded Mineral Core, 5-Ply Construction, Cat. A, PP
45 Minute Rated Mineral STC35/34 (FD5-45PP STC 35/34) Bonded Mineral Core, 5-Ply Construction, Cat. A, PP (Fire Test Standards IBC, UL-10C, CAN/ULC S104, & NFPA 252) Single Swing (STC35) Pair or Double
More informationProduct Guide Specification For Nonrated & 20-Minute Rated Doors
Woodtech Trading Company 455 Fourth Avenue E.N. P.O. Box 2609 Columbia Falls, MT 59912 800-775-1352 (phone) 800-775-1353 (fax) www.woodtechdoor.com Product Guide Specification For Nonrated & 20-Minute
More informationTHIS PAGE INTENTIONALLY LEFT BLANK
THIS PAGE INTENTIONALLY LEFT BLANK Seamed Edge Doors 1000 Series 16 and 18 Gauge Doors Cold Rolled or Galvanized Steel Tight Corner Seam Full Body Polystyrene Core or Honeycomb Core Non-Handed Design 12-Gauge
More informationBovard Studios Inc. Section April 6, 2004 Page 1
April 6, 2004 Page 1 This section includes solid flush and surface articulated wood doors, may have veneer facing, solid or glazed (stained glass) design, factory pre-fit, may be factory finished or site
More informationDETAILED STILE AND RAIL WOOD DOOR SPECIFICATION
DETAILED STILE AND RAIL WOOD DOOR SPECIFICATION UNIVERSITY CONTACT: Structural Services, Maintenance & Operations (302) 831-8456 PART 1 GENERAL DOORS 1.01 GENERAL PROVISIONS 1. The Drawings and General
More informationMASTERSPEC TECHNICAL SPECIFICATIONS DIVISION 08 - OPENINGS
SECTION 081433 - STILE AND RAIL WOOD DOORS PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Exterior stile and rail wood doors and sidelites. 2. Interior stile and rail wood doors. 3. Interior fire-rated,
More informationNon-Rated Agrifiber (AF5-NR) Bonded Agrifiber Core, 5-Ply Construction
Non-Rated Agrifiber (AF5-NR) Bonded Agrifiber Core, 5-Ply Construction Single Swing Pair or Double Egress Core Type & Standards Agrifiber: ANSI A208.1.2009 grade LD-1 (26-28 lb/ft 3 ) Complies with CARB
More informationInstallation Instructions. 45 and 60-Minute Positive Pressure Fire-Rated Veneered Door Frame UBC & UL-10C
Wood Doors Installation Instructions 45 and 60-Minute Positive Pressure Fire-Rated Veneered Door Frame UBC 7-2-1997 & UL-10C Positive Pressure Category Requirements: Category C The Maiman Company Fire
More informationLead Lined, Non-Rated Particleboard (LL PC7-NR) Bonded Particleboard Core, 7-Ply Construction
Lead Lined, Non-Rated Particleboard (LL PC7-NR) Bonded Particleboard Core, 7-Ply Construction Single Swing Pair or Double Egress Core Type & Standards Particleboard: ANSI A208.1.2009 grade LD-1 (32 lb/ft
More informationInstallation Instructions. 45 and 60-Minute Fire-Rated Neutral Pressure Veneered Door Frame UBC & UL-10C
Installation Instructions 45 and 60-Minute Fire-Rated Neutral Pressure Veneered Door Frame UBC 7-2-1997 & UL-10C Door Requirements: Consult the door manufacturer to make sure that the doors are qualified
More informationVictory Fire Door Inspections
Vickie Evans, FDAI Over 30 years in door and hardware industry DHI instructor and Education Advocate Certified Fire Door Inspector To compartmentalize a building Deter the spread of smoke and flames Fire
More informationA & F Wood Products, Inc 5665 Sterling Drive Howell, Michigan Phone: Fax: Toll Free:
Machining Specifications Flush 20 Minute Door HINGES: Up to 3/0 x 7/0: 4 high x 105 steel, mortised, Surface (labeled self-closing spring type) 4.5 X 134 steel, mortised, surface. Over 3/0 x 7/0: 4.5 high
More informationDOOR COMPONENTS, INC Technical Data
DOOR COMPONENTS, INC Technical Data DOOR COMPONENTS, INC 7980 Redwood Ave Fontana, CA 92336 Phone (909) 770 5700 Toll Free (866) 989 3667 Fax (909) 770 5722 www.doorcomponents.com INDEX FRAMES: PAGE #
More informationNon-Rated STC43-46 (SCL5-NR STC 43-46) Bonded SCL Core, 5-Ply Construction
Non-Rated STC43-46 (SCL5-NR STC 43-46) Bonded SCL Core, 5-Ply Construction Single Swing Pair or Double Egress Core Type & Standards Structural Composite Lumber: (38 lb/ft 3 ) Maximum Sizes 4 0 x 8 0 N/A
More informationBuyLine /CON. Acrovyn Doors. Indestructible?
08 14 23/CON BuyLine 5613 Acrovyn Doors Indestructible? Facilities get damaged, Acrovyn Doors don t. Conventional doors don t stand up to daily abuse Doors in hospitals, schools and offices are subjected
More informationAMBICO Limited Section and WOOD BULLET RESISTANT DOORS AND FRAMES Page 1
Page 1 This section includes AMBICO Bullet Resistant, Wood Doors and Bullet Resistant Steel Frames which meet the UL752 Standard for Bullet-Resisting Equipment. This section relies on both the Canadian
More informationDOOR SPECIFICATIONS FLUSH HOLLOW CORE
FLUSH HOLLOW CORE Specifications: 3 & 5 Ply construction. Meets or exceeds industry standards of WDMA I.S.1. Lay Up Method Loose Maximum Sizes: Width - 4/0. Length depends on face (See faces below for
More informationSECTION WOOD DOORS
SECTION 08211 WOOD DOORS Notice to Vendors: CANV prefers to purchase products that contain tropical wood only if they are certified according to the guidelines of the Forest Stewardship Council (FSC).
More information.1 Comply with the General Conditions of the Contract, Supplementary General Conditions and the requirements of Division 1.
PAGE 1 PART 1 GENERAL 1.1 REFERENCE.1 Comply with the General Conditions of the Contract, Supplementary General Conditions and the requirements of Division 1. 1.2 RELATED WORK SPECIFIED ELSEWHERE.1 Installation
More informationDCI Hollow Metal Technical Data
DCI Hollow Metal Technical Data DCI HOLLOW METAL 7980 Redwood Ave Fontana, CA 92336 Phone (909) 770-5700 Toll Free (866) 989-3667 Fax (909) 770-5722 www.dcihollowmetal.com INDEX FRAMES: PAGE # ANCHORS:
More informationChevy Chase Club June 30, 2008 Bowie Gridley Architects
SECTION 081433 - STILE AND RAIL WOOD DOORS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationProduct Guide. An Introduction to Hollow Metal Terminology and CURRIES Product. ASSA ABLOY, the global leader in door opening solutions
Product Guide An Introduction to Hollow Metal Terminology and CURRIES Product in door opening solutions CURRIES CURRIES Company of Mason City, Iowa is pleased to introduce you to Basic Hollow Metal Terminology.
More informationB. Shop Drawings: Include elevations, door edge details, frame profiles, metal thicknesses, preparations for hardware, and other details.
SECTION 081113 - HOLLOW METAL DOORS AND FRAMES PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Standard hollow metal doors and frames. 1.2 SUBMITTALS A. Product Data: For each type of product indicated.
More informationB. Shop Drawings: Include elevations, door edge details, frame profiles, metal thicknesses, preparations for hardware, and other details.
SECTION 081113 - HOLLOW METAL DOORS AND FRAMES PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Standard hollow metal doors and frames. 1.2 SUBMITTALS A. Product Data: For each type of product indicated.
More informationSubject: Specification Compliance
Subject: 08 11 13 Specification Compliance CURRIES product quality and performance is equal to or exceeds the manufacturers listed in most 08 11 13 Specification. 16 gauge top and bottom caps must be specified
More informationMeasuring Door Gap Dimensions of Swinging Fire Doors with Builders Hardware
Recommendations for Measuring Door Gap Dimensions of Swinging Fire Doors with Builders Hardware By Keith E. Pardoe Speed, accuracy, and above all consistency are essential when determining the clearance
More informationB. Shop Drawings: Include elevations, door edge details, frame profiles, metal thicknesses, preparations for hardware, and other details.
SECTION 081113 - HOLLOW METAL DOORS AND FRAMES PART 1 - GENERAL 1.1 SUMMARY A. Section includes standard hollow metal doors and frames. 1.2 SUBMITTALS A. Product Data: For each type of product indicated.
More informationPRICE BOOK APRIL 1, 2016 USAWOODDOOR.COM Rev. 3/1/16 Thorofare, NJ
PRICE BOOK APRIL 1, 2016 USAWOODDOOR.COM 856-384-9663 Rev. 3/1/16 Thorofare, NJ 877-950-3667 USA WOOD DOOR PRODUCTS AND SERVICES MOHAWK ALGOMA MASONITE MANUFACTURER'S PREFINISH COLORS IN STOCK CUSTOM
More informationTable of Contents Holders & Stops
Copyright 2003, 2007, 2009-2012, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Table of Contents Overview.... 1 General Information.... 2 How to Select Product... 3 Options,
More informationINTERIOR ALUMINUM DOORS AND FRAMES
INTERIOR ALUMINUM DOORS AND FRAMES 8401 Rovana Circle, CA. 95828 PHONE: 1.866.566.2161 FAX: 1.888.454.2889 www.doormerica.com Updated - 9-1-2017 INTERIOR ALUMINUM FRAME SPECIFICATIONS Phone: 866-566-2161
More informationCAPTIVATING LOOK STILE & RAIL DOORS
CAPTIVATING LOOK STILE & RAIL DOORS 1 VT STILE & RAIL DOORS Whether you're restoring a historic building or wanting to add the perfect detail to a new design, you'll find the elegance and beauty your project
More informationSECTION FINISH CARPENTRY PART 1 GENERAL. 1.1 SECTION INCLUDES A. Interior Finish Carpentry Work: 1. Refer to schedule at end of Section.
SECTION 06200 - FINISH CARPENTRY PART 1 GENERAL 1.1 SECTION INCLUDES A. Interior Finish Carpentry Work: 1. Refer to schedule at end of Section. 1.2 RELATED SECTIONS A. Section 06100 - Rough Carpentry:
More informationSECTION WOOD AND PLASTIC DOORS. A. PART A and DIVISION 1 of PART B are hereby made a part of this SECTION.
SECTION 081416 PART 1 GENERAL 1.01 GENERAL REQUIREMENTS A. PART A and DIVISION 1 of PART B are hereby made a part of this SECTION. B. Examine all conditions as they exist at the project prior to submitting
More informationARCHITECTURAL STICK SYSTEMS
ABOUT THE STICK SYSTEMS: The Steelcraft Architectural Stick Systems are designed to fit virtually all construction requirements for commercial building applications. These frame assemblies are fabricated
More informationTable of Contents Holders & Stops
Copyright 2003, 2007, 2009-2018, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Table of Contents Overview.... 1 General Information.... 2 Features and Details.... 3 590
More informationSECTION HOLLOW METAL DOORS AND FRAMES
SECTION 081113 HOLLOW METAL DOORS AND FRAMES PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Standard hollow metal doors and frames. 1.2 SUBMITTALS A. Product Data: Include construction details, material
More informationSuperior Quality. Custom Crafted.
Superior Quality. Custom Crafted. Residential and Commercial Interior Doors The Edenton The Ashley The South Beach The Augusta The Manteo The Camilla The Devonshire The Berkley The Savannah The Vineyard
More information300 Series Pin & Barrel Type Continuous Stainless Steel Hinges
www.mfsales.com 300 Series Pin & Barrel Type Continuous Stainless Steel Hinges Short Form Architectural Specification: Continuous hinges shall be full height piano-type hinge providing full height door
More informationPROJECT LOCATION SECTION PREFINISHED STEEL DOOR FRAMES
SECTION 08 1213.17 PART 1 - GENERAL 1.01 SECTION INCLUDES A. Prefinished steel door frames. B. [Sidelites] [, borrowed lites] [, and transom] assemblies. 1.02 RELATED REQUIREMENTS A. Section 06 2000 Finish
More informationPRODUCT DATA CATALOG
PRODUCT DATA CATALOG CONTENTS PAGE STANDARD ELEVATIONS 2 STANDARD ELEVATIONS 3 DOOR SPECIFICATIONS 4 LOUVER SPECIFICATIONS 5 GLAZING SPECIFICATIONS 5 DOOR HANDING CHART 6 CLINE STANDARD HARDWARE LOCATIONS
More informationHeavy Wall Applied Stop Tube Frame and Door Installation
INSTALLATION INSTRUCTIONS Heavy Wall Applied Stop Tube Frame and Door Installation IMPORTANT: Read all instructions before beginning installation. These instructions are provided to help prevent installation
More informationInspiration: Inside and Out
Inspiration: Inside and Out Interior and Exterior Stile and Rail Wood Doors Opening New Possibilities Introducing Exterior Stile and Rail Doors The beauty and durability of an architectural wood door shouldn
More informationSECTION BULLET- RESISTANT DOORS
1 SECTION 08 3950 BULLET- RESISTANT DOORS PART 1- GENERAL 1.01 SUMMARY A. This Section Includes: 1. Bullet- resistant steel door and frame systems. 2. Door hardware for bullet- resistant steel door and
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Thermally Broken Framing and Door Installation SL-450TB (2" x 4-1/2" with 1" Glazing) & SL-600TB (2" x 6" with 1" Glazing) IMPORTANT: Read all instructions before beginning installation.
More informationSECTION HOLLOW METAL DOORS AND FRAMES
PART 1 GENERAL 1.01 SECTION INCLUDES SECTION 08 11 13 HOLLOW METAL DOORS AND A. Non-fire-rated hollow metal doors and frames. B. Hollow metal frames for wood doors. C. Fire-rated hollow metal doors and
More informationKarpen. Steel. Custom Doors & Frames. The Custom Quick-Ship Professionals. Division
Karpen Steel Custom Doors & Frames The Custom Quick-Ship Professionals Division 08 1110 right. time. MADE ON When we call ourselves The Custom Quick-Ship Professionals, it s not a declaration we take lightly.
More informationSeries D200 Narrow Stile Series D300 Medium Stile * D500 Wide Stile ** Standard Aluminum Swing Entrance Doors
E F C O C O R P O R A T I O N Visit us on the web at efcocorp.com IMPACT GRADE BALLISTIC GRADE Series D200 Narrow Stile Series D300 Medium Stile * D500 Wide Stile ** Manufacturer Configurations Narrow
More informationASSA ABLOY Overview Playbook
ASSA ABLOY Overview Playbook Attack Resistant Openings ASSA ABLOY is the global leader in door opening solutions, dedicated to satisfying end-user needs for security, safety and convenience 1 About This
More informationINSTALLATION SHOP DRAWINGS FOR MINNEAPOLIS, MN
MINNEAPOLIS, MN 2-0- 2-- General Notes Abbreviations Deviations from Architectural Specifications Deviations from Architectural Drawings ALUM. = ALUMINUM B.O. = BY OTHERS CONT. = CONTINUOUS. = CLEARANCE
More information129 KITCHEN BASE CABINET 480
129 KITCHEN BASE CABINET 480 There are two sorts of kitchen cabinets: base cabinets, which sit on the floor, and wall cabinets. Base cabinets provide both storage space and work surfaces. They often house
More informationDOOR COMPONENTS. from Ferche Millwork. Astragals. Jambs Mull Center Stop Brickmould. Sills Thresholds. Rated Frames
DOOR COMPONENTS from Ferche Millwork Ferche Millwork is your one-stop-shop for all your door hanging needs. Interior, exterior, residential or commercial, we have it or can make it! Astragals Jambs Mull
More informationWOOD COLLECTION GENERAL INFORMATION / LIMITED WARRANTY. MITRED MORTISE & TENON SHAKER MDF FIVE PIECE.
GENERAL INFORMATION / LIMITED WARRANTY WOOD COLLECTION CHANGES TO ORDER LEAD TIME Changes to an order can not be made once the order is in production. An order can go into production as early as 24 hours
More information1530(F) Mortise Exit Devices Installation Instructions
1530(F) Mortise Exit Devices Installation Instructions Singe Doors or Pairs (2) 12-12-24 PFHUM/WS 798 Universal Strike Standard Device Package Devices are packed ready for application reinforced metal
More informationHeavy Wall Applied Stop Tube Frame and Door Installation
INSTALLATION INSTRUCTIONS Heavy Wall Applied Stop Tube Frame and Door Installation Read all instructions before beginning installation. These instructions are provided to help prevent installation problems
More informationCheckmate Stops & Holders. Absolute Door Control and Entire Opening Protection
Checkmate Stops & Holders Absolute Door Control and Entire Opening Protection checkmate stops & holders TABLE OF CONTENTS General Information...3 How to Select Product...4 Options...5 Certifications...5
More informationWarranty, Care & Finish, and Installation
Warranty, Care & Finish, and Installation INDEX Page Warranty... 2 Care & Finishing, and Installation... 3 Claim Procedure... 5 Page 1 Infinity, Encore, & Ovation Warranty WARRANTY PERIOD: TYPE INTERIOR
More informationINSTALLATION INSTRUCTIONS. Thermal Entrances AA 250/AA 425 THERMAL DOOR WITH TRIFAB 601/601T FRAMING
JANUARY, 2014 1 INSTALLATION Thermal Entrances AA 250/AA 425 THERMAL DOOR WITH TRIFAB 601/601T FRAMING INSTRUCTIONS 2 FRAME ASSEMBLY JANUARY, 2014 601442 SHEAR BLOCK BALL BEARING NRP BUTT (FACTORY APPLIED
More informationWhat You ll Find In This Brochure:
J O B S I T E Useful Jobsite Information For VT Architectural Wood Doors What You ll Find In This Brochure: VT Industries, Inc. provides architectural grade interior wood doors that have been manufactured
More informationThermally Broken Framing and Door Installation
INSTALLATION INSTRUCTIONS Thermally Broken Framing and Door Installation IMPORTANT: Read all instructions before beginning installation. These instructions are provided to help prevent installation problems
More informationSeamed Edge Doors 1000 Series
Seamed Edge Doors 1000 Series 16 and 18 Gauge Doors Cold Rolled or Galvanized Steel Tight Corner Seam Full Body Polystyrene Core or Honeycomb Core Non-Handed Design 12-Gauge Closer Reinforcement Reversible
More informationSTC 46 3-Sided Paired Frame (Double Rabbet Only)
(Toll Free) Phone 866-452-1845 Fax 910-452-1848 STC 46 3-Sided Paired Frame (Double Rabbet Only) FRAME PART DIMENSIONS E E THROAT THROAT MINIMUM 3 5/16" MAXIMUM 13" D A=Jamb Depth MINIMUM 4 5/16" MAXIMUM
More informationThis section describes the design requirements and materials/products for door hardware.
Facilities Division Standards Section 08710 Door Hardware SUMMARY This section describes the design requirements and materials/products for door hardware. DESIGN REQUIREMENTS Coordinate with the McCarran
More informationTender No Section St. James - Assiniboia Centennial Pool Fitness Facility Addition Page 1
Fitness Facility Addition Page 1 PART 1 GENERAL 1.1 SECTION INCLUDES.1 Finish carpentry items including shop prefabricated casework and countertops..2 Hardware and attachment accessories..3 Wood Benches..4
More informationACME 50 Application Guide
ACME 50 Application Guide p1 CONTENTS Features & Benefits... 2 Product Images... 3-8 TRIM AND CONNECTORS Trim & Connector Diagram.... 9 Partition Profile Section... 10 Adjustability.... 11 Ceiling & Floor
More informationJ O B S I T E. What You ll Find In This Brochure: Please take a few minutes to read through all information to ensure customer satisfaction.
J O B S I T E Useful Jobsite Information For VT Architectural Wood Doors What You ll Find In This Brochure: VT Industries, Inc. provides architectural grade interior wood doors that have been manufactured
More informationSPLIT FRAME INSTALLATION INSTRUCTIONS
SPLIT FRAME INSTALLATION INSTRUCTIONS Revised 2014/09/29 Guillaume Gauthier, Eng. Product Manager RECEIPT OF MERCHANDISE... 2 INSTALLATION... 2 SPLIT FRAME COMPONENTS... 3 TOOLS, HARDWARE AND PARTS...
More informationC-Series & S-Series Classic Frame with Transom (Single or Pair)
1. TOOLS REQUIRED Tape measure 6' magnetic level 3' magnetic level Safety Glasses Screw gun #2 Screwdriver tip #3 Screwdriver tip Philips Head screwdriver (Used to move frame on wall using oval slots on
More informationVISION FRAMES. Specify Stock Sizes. Save Time and Money. Square Inches. Order Size and Door Cutout. LoPro. Visible Lite. .com
Specify Stock Sizes Save Time and Money LoPro Order Size and Door Cutout Visible Lite Square Inches Visible Lite Glass Size Large Round Lite Medium Round Lite Small Round Lite Full Glass lite Half Glass
More informationPERFORMANCE TEST REPORT. Rendered to: GLASSCRAFT DOOR COMPANY. PRODUCT TYPE: 6' x 8' Double Inswing Hardwood Door with Half Circle Transom
PERFORMANCE TEST REPORT Rendered to: GLASSCRAFT DOOR COMPANY PRODUCT TYPE: 6' x 8' Double Inswing Hardwood Door with Half Circle Transom Title Uniform Load Deflection Test Pressure Uniform Load Structural
More informationGuide Specification Section Interior Aluminum Doors and Frames
Guide Specification Section 08 11 16 Interior Aluminum Doors and Frames SECTION 08 11 16 The Sliding Door Company s door and frame system includes glazed swing doors, sidelights, transoms, and fixed panels
More informationBlock Frame Inovo Patio Door/Transom/Sidelite Field Mulling Instructions. simonton.com/installation. If mulling sidelites, skip to Step 5.
Effective Date: 10/1/17 Tools Needed Kit Contents Safety Glasses Cordless Drill Phillips Screw Bit Two-step Drill Bit (3/8-1/8 ) Utility Knife Interior Mullion Exterior Mullion Cover Hardware Kit Clamps
More informationProduct Guide Specification
Product Guide Specification Specifier Notes: This product guide specification is written according to the Construction Specifications Institute (CSI) 3-Part Format, including MasterFormat, SectionFormat,
More informationAluminum Continuous Geared Hinges
Manufacturing, Inc. Overhead Holders & Stops Hospital Push/Pull Latches Electro-Magnetic Door Holders Electrical Power Transfer Products Stainless Steel Continuous Pin & Barrel Hinges Stainless Steel Edge
More informationSince 1950 Commercial Division
Since 1950 Commercial Division *These images represent the types of structures we specialize in. Aluminum storefronts are not available MASONRY (AS) FRAME Multiple Application 5-3/4 OAL 16 Gauge Galvaneal
More informationA. All trim that has been damages, broken, or missing shall be repaired or replaced with material of the same size, shape, and type.
SECTION 062000 - FINISH CARPENTRY PART 1 - GENERAL 1.1 SECTION REQUIREMENTS A. All trim that has been damages, broken, or missing shall be repaired or replaced with material of the same size, shape, and
More informationMusic Area Casework General 1.01 Summary Related Sections Definitions Qualifications and Quality Assurance
1.00 General 1.01 Summary Music Area Casework A. This section includes the following Scope of Work as referred to in the plans: 1. Thermally Fused Laminate manufactured casework, for use in music areas,
More information4. Partially open the operating panel and tilt the top toward the interior of the door (Figure 4). Lift the panel off the sill and set it aside.
Effective Date: 10/1/2017 Tools Needed Kit Contents Hardware Kit Safety Glasses Cordless drill Phillips screw bit Two-step drill bit (3/8-1/8 ) utility knife Interior Mullion Exterior Mullion Cover clamps
More informationD I F F E R E N T B Y D E S I G N
DIFFERENT BY DESIGN INTRODUCTION Welcome to Dorwest. If you re looking for an innovative, quality door that has countless design possibilities, we have the door for you. DIFFERENT BY DESIGN Why Dorwest?
More informationProduct Guide Specification
VT Industries, Inc. April 2014 890 Central Court New Albany, Indiana 47150 Toll Free (800) 626-6271 Fax (712) 368-4111 Website www.vtindustries.com E-mail door_info@vtindustries.com Product Guide Specification
More informationProduct Selection Guide
Selection Guide GLAZING PRODUCTS DOOR LOUVERS VISION FRAMES D o o r P r o d u c t s 4958 Stout Dr. #119 San Antonio, TX 78219 210.662.6300 Fax 210.662.2828 E-mail door@anemostat www.anemostat V I S I O
More informationFLUSHLINE ENTRANCES. Features
OCTOBER, 2006 FLUSHLINE ENTRANCES FEATURES 1 Features Flush appearance with a face sheet of fiberglass reinforced polyester (FRP) or aluminum, that is captured on four sides by integral extruded reglets
More informationIntegrity Polygon and Round Top Installation and Finishing Instructions
Integrity Polygon and Round Top Installation and Finishing Instructions 08/20/2004 70852 BEFORE YOU BEGIN IMPORTANT: Read these instructions thoroughly before beginning to install your Integrity Polygon
More informationFold-A-Way Patio Door ASSEMBLY & INSTALLATION GUIDE
Fold-A-Way Patio Door ASSEMBLY & INSTALLATION GUIDE This instruction guide provides the minimum recommended procedures to correctly prepare the rough opening, install a fold-a-way patio door unit and apply
More informationWHITE W/OAK TRIM NATURAL MEDIUM NORTHPORT OAK
WHITE W/OAK TRIM NATURAL MEDIUM NORTHPORT OAK Accessories. We believe that functionality is at the heart of any great kitchen. Above are a few of the accessories available with Merillat Essentials. The
More informationED5800 (A) Series. Installation Instructions. Concealed Vertical Rod. Exit Device WARNING
Strike Shim (2) Supplied Strike Plate (3) 10-24 x 3/4" PFHMS (6) 10-24 x 1/2" PFHMS Top Latch TopTube Concealed Vertical Rod Exit Device Important: For use with metal doors only. Device is packed ready
More informationImola. elmwood fine custom cabinetry. scroll for more information. General Specifications. Prime Center Panel. Additional Panel Options
4.7 5. 5.7 General Specifications Door Construction: 5 Piece Wood Mortise & Tenon door. Center Panel Construction: 3/8 thick veneer flat center panel, virtually flush with back of rails. See drawings for
More informationAndersen Complementary Clad Casement Windows (2005 to Present)
Andersen Complementary Clad Casement Windows (2005 to Present) What s in This Section Clad Casement Windows... Page 3 Part Illustrations... 3 Parts Illustration - Standard Casements... 3 Parts Illustration
More informationImola 44. elmwood fine custom cabinetry. scroll for more information. General Specifications. Prime Center Panel. Additional Panel Options
General Specifications Prime Center Panel 4.7 5. 5.7 Door Construction: 5 Piece MDF with 44 applied moulding around the outside of the rails. Center Panel Construction: 3/8 recessed panel. See drawings
More informationC. HMMA 863: Guide Specifications for Detention Security Hollow Metal Doors and Frames
SECTION 083463 DETENTION DOORS AND FRAMES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationHOLLOW METAL DOOR/WINDOW SYSTEM FOR THERMALSAFE CF WALLS WINDOW ASEMBLY GUIDE PIONEERING INSULATED METAL PANEL TECHNOLOGY
HOLLOW METAL DOOR/WINDOW SYSTEM FOR THERMALSAFE CF WALLS WINDOW ASEMBLY GUIDE PIONEERING INSULATED METAL PANEL TECHNOLOGY PIONEERING INSULATED METAL PANEL TECHNOLOGY TABLE OF CONTENTS DETAIL TITLE PAGE
More informations tops & holder s Absolute Door Control and Entire Opening Protection
check mate s tops & holder s Absolute Door Control and Entire Opening Protection Copyright 2001-2018, ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or
More informationInstallation Instructions
TEL: 09 579-8895 FAX: 09 579-2933 EMAIL: sales@nzfiredoors.co.nz NZ Fire Doors Ltd, 89 Gavin Street, Ellerslie, PO Box 12709, Penrose 1642, Auckland, New Zealand. www.nzfiredoors.co.nz Installation Instructions
More informationWELLNESS CENTER REMODEL UNIVERSITY OF CALIFORNIA, MERCED MERCED, CALIFORNIA PROJECT NO.: 907432 C. Solid Surfacing Material: 1. Manufacturers: D. Wood: a. First Floor; Wilsonart International, Solid Surfaces,
More informationSliding Glass Door Assembly and Installation Guide
Sliding Glass Door Assembly and Installation Guide Index Door System Components and Hardware The following components are needed to complete the installation of your Sliding Patio Door unit. Check all
More information