Double Pedestal Desk INSTRUCTIONS CARTONS: TT7130, MP4024, (2)PBBF30 TT-B PED-A PED-A MP-C

Transcription

1 Page 1 Organize your parts and hardware. You will need (2) people, a Phillips head screwdriver and rubber mallet. TT-B Parts : TT-B: Desk Top (71 x 29.5 x 1 ) : Box Box File Pedestal (15.5 x 29.5 x 25 ) : Ped Foot Bracket (29.5 D) : Modesty (40 x 25 x 1 ) Figure 1: : Ped Top Bracket (29.5 D) Cam ock Assembly: To open Cam, point arrow toward Cam Pin hole. To lock Cam, turn clockwise. MPORTANT NOTCE: Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the parts from being scratched. Check to be sure that you have all parts and hardware. Remove all wrapping materials, including staples & packing straps before you start to assemble. Do not tighten all screws/bolts until completely assembled. eep all hardware parts out of reach of children.

2 Page 2 Hardware : F: Corner Bracket G: Allen ey H: Set of eys : Fine threaded Cam Pins : 1.5 ong Bolts (38mm) : 3/4 Wood Screws (19mm) 8 M: Glides : 3/4 Short Bolts (19mm) N: Cam Caps O: Handles P: Handle Screws (25mm) Quantity: 6 REMOVE PEDESTA DRAWERS FOR NSTAATON STEP 1 : Pull out each drawer on the Box Box File Pedestals() and find the black tabs at the end of the suspension. ift one side up and press the other side down and simultaneously pull the drawer out. This will unlock the drawer and release it. Repeat this for all drawers.

3 Page 3 STEP 2 : Remove 2 Cam Pin Covers from each of the Box Box File Pedestals() in the location shown below. Then insert a Fine threaded Cam Pin() into each of the revealed inserts. STEP 3 : Attach the Ped Foot Bracket() to the bottom of 1 Box Box File Pedestal() with 3 ong Bolts() and 3 Wood Screws(). Also, insert 2 Glides(M) into Ped Foot Bracket(). Repeat this step for the second Box Box File Pedestal. NOTE: Flange on Ped Foot Bracket should face toward your Cam Pin location from STEP 2. M M Flange

4 Page 4 STEP 4 : Attach both Ped Top Brackets() to Desk Top(TT-B) as shown below. Use 6 Short Bolts() per Ped Top Bracket. Do not tighten bolts until all bolts have been started. TT-B STEP 5 : Attach 1 Box Box File Pedestal() to one of the Ped Top Brackets() using 3 ong Bolts(). NOTE: Cam Pins on the Box Box File Pedestal should face inward for modesty attachment. STEP 6 : Attach the Modesty() to the Box Box File Pedestal() by inserting Cam Pins into Cam ocks. ock Cams (Figure 1). NOTE: Cam ocks should face the interior of the Desk. Cam Pin ocation Cam Pin ocation

5 Page 5 STEP 7 : Attach the second Box Box File Pedestal() to the Modesty() by sliding the Pedestal into Cam ocks on the Modesty. ock Cams (Figure 1). STEP 8 : Attach the second Box Box File Pedestal() to the second Ped Top Brackets() using 3 ong Bolts(). STEP 9 : For additional stability, attach 1 Corner Bracket(F) to each Box Box File Pedestal() and the Modesty() with 6 Wood Screws() per Corner Bracket. STEP 10 : Flip desk upright with at least 2 people. Replace drawers and attach Handles(O) with 2 Handle Screws(P) to the Box Box File Pedestals(). Finish by covering all Cam ocks on the Modesty() with Cam Caps(N).