Star Bright Chest of Drawers L3938

Transcription

1 Thank you for shopping with GLTC, we hope you enjoy having this product in your home. We know assembling furniture, toys or accessories is not everyone s favourite way to spend their time, so we ve tried to make assembling this item as quick and painless as possible. Star Bright Chest of Drawers L3938 Hopefully our efforts will have been worthwhile and you ll sail through the whole process. But if it all feels a bit too much like hard work, then we do have an assembly company we can recommend: the Flatpack Construction Company offers a nationwide service and can be contacted on Good luck! A few important pointers before you start: It might be worth checking on our website that there are no updates or revisions to these instructions (if we have had helpful feedback from other customers we pass it on via the product web page). Simply check any site updates. Please read the instructions right through before you start, and check separating all the hardware into piles makes it easier to be sure that everything is present and correct. Make sure you have the right tools. Allen keys are provided if required, tools you need at the beginning of the instructions. It s a good idea to build the unit in the room where you are going to be using it, to avoid the need to move it after it s been assembled. easy - medium - hard two-person job V1 06/06/2016 Do not throw away any packing materials until assembly is complete, just in case you accidentally discard smaller parts or hardware. 1

2 Safety Warnings: Adult assembly required. Unassembled product contains small parts which may present a choking hazard. Children should be kept away from the product during assembly to avoid any possible risk of injury. This product is heavy, we recommend that you build it where you are planning to use it. DO NOT use power tools in the assembly of this product as there is a risk of over-tightening and consequently splitting of the wood. To avoid possible injury from tipping, DO NOT allow children to climb on the product. Always use the wall straps provided. suitable for the wall type. If in doubt, please seek professional advice. Please retain these instructions for future reference. Customer Service: not begin assembly and do not use the item. Please contact GLTC Customer Services on immediately. We do stock spare hardware packs at our warehouse, so we should be able to send you a replacement pack immediately if required. Product Care: Wipe clean using a soft damp cloth followed by a dry cloth. Do NOT use cleaning products which contain ammonia, solvents or abrasive material. Do NOT expose the item to extremes of heat and humidity. Could we do better? If there is anything you think could be improved in these instructions or in the assembly of this product we d be grateful if you could let us know; we ll pass any helpful hints and tips on to other customers via our website and update the instructions. All you need to do is drop us a line at instructions@gltc.co.uk Thank you 2

3 Component Check List Component Check List A B K L 1x Vertical Divider Panel 1x Wide Horizontal Divider Panel 4x Drawer RH Side 2x Large Drawer Back C D M N 1x LH Side Panel 1x Narrow Horizontal Panel 2x Large Drawer Base 1x RH Small Drawer Front E F O P 1x RH Side Panel 1x Base Plinth 1x LH Small Drawer Front 2x Small Drawer Base G H Q 1x Top Panel 1x Base Panel 2x Small Drawer Back I J 2x Large Drawer Front 4x Drawer LH Side 3

4 Component Check List Component Check List #2 8x Runner Sides 8x Runners 12x Screws 16mmL 48x Screws 12mmL x Wooden Dowels 20mmL 18x Screws 25mmL 2x Anti Tip Straps 2x Screws 3.5 Diameter x18mml 3 You will need (not supplied) 28x Cam Dowels 35mmL 28x Cam Locks 14mm Diameter 1x Allen Key Phillips Head Screwdriver #7 #8 4x Barrel Nuts 4x Threaded Bolts 42mmL 4

5 STEP 1: Take vertical divider panel A and attach a runner side to BOTH sides of the panel. Note the position of the screws in the close up illustration and ensure the stopper of the runner is at the back of the panel as illustrated. NOTE: You will be building this unit face down. To make later steps easier and also to protect the product during the building process, we suggest laying the polystyrene packing STEP 2: Attach panel A to the wide horizontal divider panel B. Note the small drill holes along the top edge on panel B should be visible and facing upwards and the larger drill holes on the face of the panel should be facing towards the base (as shown). The stopper A A place. FRONT A B Hardware for Step 1: Hardware for Step 2: 6x 12mmL Screws 2x 25mmL screws 2x Runner Sides FRONT 2x Wooden Dowels 5

6 STEP 3: Take LH side panel C and attach 3x side runners (). Use the close up detail for the screw positions on the runner and ensure the stopper of the runner is at the back of the panel. Note: Panel C should be positioned with the grooved edge facing upwards and the smaller drill holes facing towards the base as shown. When the runners are in place, insert 3x cam dowels () into the larger of the drill holes that are positioned between the runners. STEP 4: Insert 4x wooden dowels () into the remaining holes in between the runners of side panel C and push panels B and D into position as shown. Insert 3x cam locks () into the large holes of panels B & D facing the base and turn clockwise to lock. C C B D Hardware for Step 3: 3x Cam Dowels Hardware for Step 4: 9x 12mmL Screws 3x Cam Locks 3x Runner Sides 4x Wooden Dowels 6

7 STEP 5: Take RH side panel E and attach 3x side runners (). Use the close up detail from step 3 for the screw positions on the runner and ensure the stopper of the runner is at the back of the panel. Note: Panel E should be positioned with the grooved edge facing upwards and the smaller drill holes facing towards the base as shown. When the runners are in place, insert 3x cam dowels () into the larger of the drill holes that are positioned between the runners. STEP 6: Connect panel E to the part assembled unit using 4x wooden dowels (). When in position, insert 3x cam locks () into the large drill holes of panels B & D and turn clockwise to lock. E E D B C Hardware for Step 5: 3x Cam Dowels Hardware for Step 6: 9x 12mmL Screws 3x Cam Locks 3x Runner Sides 4x Wooden Dowels 7

8 STEP 7: STEP 8: Position base plinth F onto the unit using 4x wooden dowels (), ensuring the recessed groove of the base plinth is facing up. When in place, insert 4x barrel nuts (#7) into the holes on the inside of the side panels and then insert 4x bolts (#8) into the base plinth. Tighten fully with the Allen key. NOTE: This is where it helps building on the polystyrene packaging. The unit will now be raised slightly making it easier to attach the base & top panels without having to lift up the part constructed unit. Prepare the top panel G with 6x cam dowels (). G Hardware for Step 8: 2x 6x Cam Dowels #8 #7 #7 #7 #7 G B C #8 F #8 E Hardware for Step 7: #8 4x Wooden Dowels 4x #8 Bolts Hardware for Step 9: 6x Cam Locks STEP 9: Position the top panel G onto the unit using 6x wooden dowels (), keeping the recessed groove of the panel facing up. 4x #7 Barrel Nuts 6x Wooden Dowels Insert 6x cam locks () into the larger drill holes on the inside faces of the unit and turn clockwise to lock. F 8

9 STEP 10: Attach the two back panels (H), leaving the holes on the top corners free. STEP 11: TWO PEOPLE are needed to stand the unit upright. Now attach the anti-tip straps to the remaining holes in the top corners of the unit. 1 1 H H 2 2 H H Hardware for Step 11: Hardware for Step 10: 2x 1 Anti Tip Straps 12x 16mmL Screws 2x 2 18mmL Screws 9

10 STEP 12: Create the drawers. Start by attaching the remaining parts of the runners to ALL of the side panels J & K. Note the open end of the runner should be at the back of the drawer side panel, by the visible drill holes. STEP 13: Prepare both of the large drawer fronts. Hardware for Step 13: I I J #2 FRONT #2 #2 K 8x Cam Dowels STEP 14: Build the two large drawers by joining a set of side panels J & K to drawer back panel L, keeping the grooves aligned on the inside. When secure, slide in the drawer base panel M and follow with the drawer front I. Fix in place with 4x cam locks (), turning clockwise to lock. Repeat with the second J large drawer. L FRONT Hardware for Step 12: Hardware for Step 14: K M I 24x 12mmL Screws 8x Cam Locks 8x #2 Runner 8x 25mmL Screws 10

11 STEP 15: STEP 17: Prepare the two small drawer fronts. N O Hardware for Step 15: Build the LH small drawer by joining a set of side panels J & K to drawer back panel Q, keeping the grooves aligned on the inside. When secure, slide in the drawer base panel P and follow with the drawer front O. Fix in place with 4x cam locks (), turning clockwise to lock. Q K Hardware for Step 17: J P O 8x Cam Dowels 4x Cam Locks STEP 16: Build the RH small drawer by joining a set of side panels J & K to drawer back panel Q, keeping the grooves aligned on the inside. When secure, slide in the drawer base panel P and follow with the drawer front N. Fix in place with 4x cam locks (), turning clockwise to lock. 4x 25mmL Screws STEP 18: Insert the drawers. Q J Hardware for Step 16: K P N 4x Cam Locks 4x 25mmL Screws 11 The anti-tip wall straps should now be attached to the wall using hardware that is suitable for the type of walls in your home (not provided). Copyright 2016 G.L.T.C. Ltd. All rights reserved. Great Little Trading Company and GLTC are registered trade marks of G.L.T.C. Limited.