Lateral/ Single Shelf Low Credenza INSTRUCTIONS CARTONS: TT6020, PLF3020, PSC3020

Transcription

1 Page 1 INSTUCTINS rganize your parts and hardware. You will need (2) people, a Phillips head screwdriver and a rubber mallet. TT-H LS-E PED-L LS-D PED- LS-B Parts : Figure 1: : Back Panel (28 x x 1 ) LS-B: Base Panel (28 x 19 x 1 ) LS-C: Top Panel (28 x 16 x 1 ) Cam Lock Assembly: To open Cam, point arrow toward Cam Pin hole. To lock Cam, turn clockwise. LS-D: Foot Bracket (19.75 D) LS-E: Shelf (28 x x 1 ) : Left Side (19.75 x 17 x 1 ) : ight Side (19.75 x 17 x 1 ) TT-H: Credenza Top (59 x x 1 ) Parts List continued on back. IPTANT NTICE: Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the parts from being scratched. Check to be sure that you have all parts and hardware. emove all wrapping materials, including staples & packing straps before you start to assemble. Do not tighten all screws/bolts until completely assembled. eep all hardware parts out of reach of children.

2 Page 2 Parts continued: PED-L: Lateral (29.5 x x ) INSTUCTINS PED-: Foot Bracket (19.75 D) Hardware : J: Allen ey : Wood Cam Pins 4 : 1.5 edium Bolts (38mm) N: Shelf Pins L: 2.35 Long Bolts (60mm) : 3/4 Wood Screws (19mm) 2 P: Cam Caps Q: Glides : Washers S: 1 Top Screws (25mm) 4 2 T: Handles U: Handle Screws (25mm) : Connector

3 Page 3 INSTUCTINS STEP 1 : Insert 2 Wood Cam Pins() into Back Panel(). Place Back Panel() on a flat surface with pins facing up. STEP 2 : Attach Base Panel(LS-B) and Top Panel(LS-C) to Back Panel() by inserting and locking cams (Figure 1). Note: The cam locks on the Base Panel face away from Back Panel and the cam locks on the Top Panel face the interior. LS-C LS-B STEP 3 : Insert 6 Wood Cam Pins() into the Left Side() and ight Side(). STEP 4 : Attach the Left Side() and ight Side() by inserting and locking cams(figure 1). STEP 5 : Pull out each drawer on the Lateral(PED-L) and find the black tabs at the end of the suspension. Lift one side up and press the other side down simultaneously and pull the drawer out. This will unlock the drawer and release it. epeat this for all drawers.

4 Page 4 INSTUCTINS NTE : PDUCT IS EESIBLE. PLACE CPNENTS(LW LATEAL, PEN SHELF) NEXT T EACH THE IN THE IENTATIN THAT YU CHSE. STEP 6A : Insert 2 Glides(Q) into each Lateral Foot Bracket(PED-) and pen Storage Foot Bracket(LS-D). Q Q Q Q PED- LS-D STEP 6B : n a clean, flat surface, lay both components on their backs next to one another. Attach 1 Lateral Foot Bracket(PED-) and 1 pen Storage Foot Bracket(LS-D) as shown in Figure 1-A(Left, ight) in the locations shown below(figure 1). Figure 1A- Left Figure 1A- ight Figure 1 STEP 6C : Connect both components to one another by following Figure 2 and Figure 3 as shown below. L L Figure 2 L L Figure 3

5 Page 5 INSTUCTINS STEP 7 : Attach Credenza Top(TT-H) to both Components with 8 Top Screws(S). TT-H S S STEP 8 : Insert 4 Shelf Pins(N) in pen Storage Component at desired height and place Shelf(LS-E). eplace File Drawers and attach Handles(T) with 2 Handle Screws(U) each. Finish by covering all Cam Locks with Cam Caps(P). NTE: Lip on Handle should face down.