D M. 123eFit Connectors. Part Number Code Key. Reference standard IEC and IEC IV. Environment. II. Mechanical Performance

Size: px

Start display at page:

Download "D M. 123eFit Connectors. Part Number Code Key. Reference standard IEC and IEC IV. Environment. II. Mechanical Performance"

Felix Banks
6 years ago
Views:

Reference standard IEC60169-16 and IEC60169-4 I. Electric Performance 50 range Insert Loss: (db) 0.1 Temp.

Material and Plating Insulation resistance(mω) 10000 5000 Work voltage(v) (ut) Whorl pull 1000 450 Vibration PIM(dBc) IV.

1 Reference standard IEC and IEC I. Electric Performance 50 range Insert Loss: (db) 0.1 Temp.range -40 C to +85 C Weather standard IEC /85/21 Waterproofing standard IP68 IEC Fc ROHS Compliant III. Material and Plating Insulation resistance(mω) Work voltage(v) (ut) Whorl pull Vibration PIM(dBc) IV. Environment Component Material Plating Inner conductor: Spring Copper Outer conductor: Brass Silver 5µm ut: Brass Insulator: TPFE Impedance (Ω) II. Mechanical Performance Copper tin-zine 2µm ickel 5µm Conductor resistance(mω) outer conductor <0.2 inner conductor <0.8 Super Flexible Part umber Code Key D M 1 1/2 Flexible Cable 2 1/2 Super Flex Cable D Type Type M Male F Female MR Male Right Angle 123-2AS 123eFit connectors have been designed for high performance and quick installation. The Flexline connector is a universal connector for LDF, LCF, and annular type cable. 123eFit Flexline connectors integrate a self flaring flange and retention collate. This design utilizes fewer separate components; thus decreasing the number of moving parts. Fewer moving parts means better PIM performance and fewer parts to lose. 123eFit Super Flexline connectors are a two-piece screw on style connector for FSJ, SCF, and Super Flexline cable. These connectors require no special tooling other than two wrenches and an automated stripping head. ( 29 )

123-1DM 123-1DMR 123-1DF 123-1M 123-1MR 1/2 Flexible Connectors GP/CMR/CMP straight male flexible cable connector 123-1DM right angle male flexible cable connector 123-1DMR 1.

2 123-1DM 123-1DMR 123-1DF 123-1M 123-1MR 1/2 Flexible Connectors GP/CMR/CMP straight male flexible cable connector 123-1DM right angle male flexible cable connector 123-1DMR female flexible cable connector 123-1DF.3-3.7GHz 1.02 straight male flexible cable connector 123-1M right angle male flexible cable connector 123-1MR -155 female flexible cable connector 123-1F 123-2DM 123-2DMR 123-2DF 123-2M 123-2F PIM (dbc) 123-2MR 1/2 Super Flexible Connectors GP/CMR/CMP Part # straight male super flexible cable connector 123-2DM 1.08 right angle male super flexible cable connector 123-2DMR female super flexible cable connector 123-2DF straight male super flexible cable connector 123-2M right angle male super flexible cable connector 123-2MR female super flexible cable connector 123-2F PIM (dbc) ( 30 )

66-140 66-141 66-142 66-143 QMA right angle field termination type LMR 240 66-140 DC-2.5 GHz 1.

3 QMA right angle field termination type LMR DC-2.5 GHz 1.17 QMA field termination type LMR QMA SMA right angle field termination type LMR SMA straight field termination type LMR Male straight field termination type LMR Male right angle field termination type LMR MR Female straight field termination type LMR Din Male Striaght field termination type LMR DM Din male right angle field termination type LMR DMR QMA right angle field termination type LMR QMAR DC-2.5 GHz 1.17 QMA field termination type LMR QMA SMA right angle field termination type LMR SMAR SMA straight field termination type LMR SMA Male straight field termination type LMR M Male right angle field termination type LMR MR Female straight field termination type LMR F Din Male straight field termination type LMR DM Din Male right angle field termination type LMR DMR 400 Connectors ( 31 ) 240 Connectors

1/2 123eFIT Flexible Installation Procedure Review the instructions carefully prior to

Dust or grease will effect the overall performance of the assembly.

Strip the cable; a proper strip will result in the corrugation being stripped to the middle

2. Install O-rings to the cable and lubricate with grease (Fig 6)

Using a 19MM wrench screw clockwise the connector clamp into the main body of the connector

Install the connector clamp to the cable; the collate (inside the connector clamp) should

If the cable is not flush with the collate the 7.

These instructions apply to all 123-1-XXX connector series and type connectors FIG.

2 Main body, connector clamp, O-ring and grease. FIG. 4 FIG. 5 FIG.

7 OT EOUGH Lubricate both O-rings with grease.

4 1/2 123eFIT Flexible Installation Procedure Review the instructions carefully prior to assembly. Make sure that the area for assembly is clean and free from any type of debris. Dust or grease will effect the overall performance of the assembly. It is recommended that the installer wear safety glasses and gloves. 1. Strip the cable; a proper strip will result in the corrugation being stripped to the middle of the crest. Refer to (Fig 4) and/or (Fig 5) for a proper strip. 4. Add grease to the connector clamp O-ring (Fig 7). 2. Install O-rings to the cable and lubricate with grease (Fig 6). 6. Hold the main body still with the 22MM wrench. Using a 19MM wrench screw clockwise the connector clamp into the main body of the connector (Fig 10). 5. Install the main body of the connector (Fig 9). 3. Install the connector clamp to the cable; the collate (inside the connector clamp) should lock into place on the first corrugation. If you can easily pull it off, the strip is bad. If the cable is not flush with the collate the 7. Tighten the assembly to 20-M (tight snug fit) do not over tighten. strip is bad (Fig 7). These instructions apply to all XXX connector series and type connectors FIG AS - Auto Stripper, 19MM and 22MM open box wrenches. FIG. 2 Main body, connector clamp, O-ring and grease. FIG. 4 FIG. 5 FIG. 3 Install the 123-1AS into a standard drill and strip the cable. FIG. 6 FIG. 7 OT EOUGH Lubricate both O-rings with grease. First corrugation must be stripped to the middle of the crest. Add O-ring. TOO MUCH FIG. 8 FIG. 9 Install connector and lubricate O-ring with grease. FIG. 10 FIG. 11 PERFECT Proper stripping. Flare copper corrugation with small flathead screwdriver to prevent connector from detaching. Install the main body. Rotate connector clamp clockwise while holding the main body still. Final. ( 32 )

1/2 123eFIT Super Flexible Installation Procedure Review the instructions

Make sure that the area for assembly is clean and free from any type of debris.

It is recommended that the installer wear safety glasses and gloves. 1.

Install the O-ring on to the cable (Fig 4) and lubricate with grease (Fig 5)

Screw the main body of the connector into the connector clamp clockwise with a

Install the connector clamp to the cable; screw clockwise until the connector

These instructions apply to all 123-2-XXX connector series and type connectors

2 Main body, connector clamp, O-ring and grease. FIG.

5 1/2 123eFIT Super Flexible Installation Procedure Review the instructions carefully prior to assembly. Make sure that the area for assembly is clean and free from any type of debris. Dust or grease will effect the overall performance of the assembly. It is recommended that the installer wear safety glasses and gloves. 1. Strip the cable. 4. Install the main body of the connector (Fig 7). 2. Install the O-ring on to the cable (Fig 4) and lubricate with grease (Fig 5). 5. Using a 19MM wrench hold the connector clamp in place. Screw the main body of the connector into the connector clamp clockwise with a 20MM wrench (Fig 8 ). 3. Install the connector clamp to the cable; screw clockwise until the connector clamp is flush with the cable corrugation (Fig 6). Lubricate the O-ring with grease. 6. Tighten the assembly to 20-M (tighten to a snug fit) do not over tighten. These instructions apply to all XXX connector series and type connectors FIG AS - Auto Stripper, 19MM and 20MM open box wrenches. FIG. 2 Main body, connector clamp, O-ring and grease. FIG. 4 Add O-ring. FIG. 7 Install the 123-2AS into a standard drill and strip the cable. FIG. 5 Lubricate O-ring with grease. Install the main body FIG. 3 FIG. 6 Screw on the connector clamp until its flush with the corrugation. Lubricate O-ring with grease. FIG. 8 Rotate main body clockwise while holding the connector clamp still. FIG. 9 Final. ( 33 )

STANDARD COAXIAL CONNECTORS. Eco 7/16 series

STANDARD COAXIAL CONNECTORS. Eco 7/16 series STANDARD COAXIAL CONNECTORS Eco 7/16 series Eco 7/16 INTRODUCTION GENERAL Standard coaxial connectors Screw on coupling Compliant to CECC and IEC standards 50 Ω APPLICATIONS Broadcast RF components (filters,