Repair Instructions. Replacing a La Z Time Mechanism Side Subassembly. Remove the Back(s): Remove the Mechanism Assembly: CAUTION.

Size: px
Start display at page:

Download "Repair Instructions. Replacing a La Z Time Mechanism Side Subassembly. Remove the Back(s): Remove the Mechanism Assembly: CAUTION."

Transcription

1 Replacing a La Z Time Mechanism Side Subassembly Tools Required: Slotted Screwdriver Power Driver 8" Driver Extension Ruler Note: Extension springs are not typically used on non-chaise standard width styles, but can be added as a service solution for additional legrest support when needed. Remove Extension T 30 Torx Bit T 25 Torx Bit Torque Wrench Socket Wrench Please read through all instructions prior to beginning the repair. CAUTION Risk of injury: Always wear safety goggles or glasses when completing repairs. 2. Note: Illustrations show the style 480 and the left side of the left mechanism being replaced. Remove the Back(s): 1. Pull the lower outside back cover to loosen the back upholstery from the fastening tape on the bottom side of the rear seat rail. Close the legrest. Using the T 30 bit, remove the four ½" truss head screws securing the reclining unit to the bottom rails. If repairing a reclining chair, remove the bottom rails. If repairing a motion sofa or motion modular unit, carefully move the reclining unit to be repaired away from the other units. Remove (4) ½" Screws 2. Unlock the back brackets using a slotted screwdriver, remove the upholstered back and set the back aside. If needed, refer to Replacing a Back work instruction for back removal and installation instructions. Repeat steps 1 and 2 for all backs. 3. Carefully turn the unit upside down to rest on the top of the arms. 3. Remove (4) ¾" Screws Remove the Mechanism Assembly: 1. Extend the legrest. Using the T 25 bit, remove the four ¾" pan head screws attaching the upholstered legrest to the mechanism. Set the screws and legrest aside. If repairing a wide style, or chaise style, or any style using a center extension spring, extend the legrest, unhook the extension spring and set it aside. Refer to image at top right. 1 of 7

2 4. If repairing a non chaise style, use the T 25 bit to remove the two ¾" pan head screws attaching the upholstered mid ottoman to the mechanism. Set the screws and mid-ottoman aside. Unhook Cable Return Remove (2) ¾" Screws Remove the black nylon trip lever from the mechanism. Rotate the trip lever until the tab aligns with the slot in the side rail, pull it out away from the mechanism and set the assembly aside. Unhook the extension spring on the side of the mechanism and set aside. Remove Trip Lever Unhook Extension Disconnect the cable end of the release subassembly from the mechanism side rail by sliding the end off the mount. 9. Using the T 25 bit, remove the four 1¼" pan head screws securing the mechanism to the seat side rails. The mechanism is now detached from the body assembly. Left Sid e 6. Remove (4) 1¼" Screws 7. Unhook the cable return spring from the mechanism side rail. Refer to image at top right. 2 of 7

3 10. If repairing a non chaise style, remove the mid ottoman bracket from the side of the mechanism that you are replacing. Use the T 25 bit to remove the 3/8" truss head screw securing the bracket to the mechanism. Set the screw and bracket aside. Remove both brackets if replacing both mechanism side subassemblies. 2. Extend the legrest. 3. Using a socket wrench and a T-30 bit, remove the ½" truss head screw securing the front stabilizer rail to the side mechanism. Set the screw aside. Remove 3/8" Screw and Ottoman Bracket Remove ½" Screw Using a socket wrench and a T 30 bit, remove the ½" truss head screw securing the rear stabilizer rail to the side mechanism. Set the screw aside. Close the legrest. Carefully lift the mechanism away from the upholstered body and place it right side up on a work bench or table. Remove ½" Screw 5. Separate the stabilizer rails from the mechanism side subassembly. With the exception of the drive rod, the side is now detached from the mechanism. 6. Carefully pull the side subassembly out and away from the drive rod and discard. Refer to image on the following page. Install the New Side Subassembly: 1. Remove the hairpin clip from the drive rod on the side being replaced. Remove Hairpin Clip 3 of 7

4 Insert Hairpin Clip Pull Away 7. Set the new side subassembly in position. Make sure both legrests are closed so the orientation of both sides match. 8. Line the plastic bushing on the side subassembly up to the drive rod and push in place until the hairpin clip holes are closely aligned. 11. Align the New Side to the Drive Rod and Push in Place Attach Rear Rail in Middle Hole Attach the rear stabilizer rail to the new side subassembly using the socket wrench with a T 30 bit and a ½" truss head screw. Use the middle hole in the rear stabilizer rail for this connection. Go slow, keeping the screw straight to ensure proper threading and not strip the head. Torque fastener to 4½ 5 ft lbs. Move the stabilizer rails into position around the front and rear motion arms. Front Motion Arm Extend the legrest. Attach the front stabilizer rail to the new side subassembly using the socket wrench and T 30 bit and a ½" truss head screw. Use the top hole in the front stabilizer rail for this connection. Make sure the rail is completely flush to the motion arm before making this connection. Go slow, keeping the screw straight to ensure proper threading and not strip the head. Torque fastener to 4½ 5 ft lbs. Close the legrest. Rear Motion Arm 10. Align the hole in the drive rod to the hole in the plastic bushing on the new side subassembly. Insert the hairpin clip to secure the drive rod connection. Refer to image at top right. 4 of 7 Attach Front Rail in Top Hole

5 13. Repeat steps 1 through 12 if replacing both mechanism side subassemblies. Replace the Mechanism Assembly: Tighten Rear Wing Nuts Completely 1. Align the mechanism to the body assembly Check the rear wing nuts to make sure they are completely tightened. Tighten wing nuts if loose. 15. Check the front wing nuts to make sure they are in the same setting on both sides and are not completely tightened or loosened. The standard setting is 7/16" from the wing nut to the lip of the slide pivot rivet as shown below. Note: The wing nuts can be adjusted to the Using the T 25 bit, attach the mechanism to the seat side rails using four 1¼" pan head screws. Install the two front screws first, followed by the two back screws. Tighten screws as required without stripping the wood or breaking the fasteners. Attach Mechanism to Seat 3. Extend the legrest. Connect the extension spring to the side of the mechanism starting with the front connection. Make sure to orient the spring so that the open end of front hook faces toward the seat as shown below. Front /16" Wing Nuts 7 consumer s preferred setting, but should not be completely tightened or loosened and both sides should be set to the same measurement. 16. Open End Faces Toward Seat Check the adjustable legrest cams to make sure they are in the same setting on both sides. The FRONT 4. If repairing a non chaise style, attach the mid ottoman bracket. Line the mid ottoman bracket up with the legrest linkage and rotate it clockwise, toward the front of the recliner, until it stops and the holes are aligned. Use the T 25 bit and a 3/8" truss head screw to secure the connection. Torque fastener to 4½ 5 ft-lbs. Repeat for other side if both brackets were removed. Refer to image on following page. Cam in Center Position 5 of 7

6 Attach Mid Ottoman Bracket(s) Insert Trip Lever and Rotate Forward 5. If repairing a non chaise style, use the T 25 bit and two ¾" pan head screws to attach the upholstered mid ottoman to the mechanism. Torque fasteners to 3 3½ ft-lbs. Using the T 25 bit and four ¾" pan head screws, attach the upholstered legrest to the mechanism. Torque fasteners to 3 3½ ft-lbs. Hook the cable return spring to the mechanism side rail. Attach Cable Return 9. Attach Upholstered Mid Ottoman Connect the cable end of the release subassembly to the mechanism side rail. Orient the cable so the cable conduit faces away from the seat and slide the end over the mount until seated. Cable Conduit Faces Away From the Seat Attach Upholstered Legrest 7. Insert the black nylon trip lever into the mechanism side rail and rotate it toward the front of the recliner to lock it in place. Refer to image at top right. 6 of 7

7 10. Close the legrest. 11. If repairing a motion sofa or motion modular unit, carefully move the reclining unit into position next to the other unit(s). Connect Extension Front Bottom Rail Open End Faces Up Toward Seat 14. Close the legrest and return unit to its upright position. Install the Back(s): 12. Secure the reclining unit to the bottom rails using a T 30 driver and four ½" truss head screws. Start and snug up the two inside screws first, followed by the two outside screws. Do not completely tighten the screws until all four are installed. Once installed, torque these screws to 4½ 5 ft-lbs. Attach Mechanism to Bottom Rails WARNING Risk of injury: Do not operate the unit until the back is installed and locked. 1. Lay the back across the arm(s) of the body. Lift the back at a slight angle and align the brackets on the back with the mechanism brackets in the body. 2. Lower the back onto the body, making sure the back and mechanism brackets are completely engaged. To do this, while standing behind the unit, twist the back from side to side. If one or both sides move out of position the brackets are not engaged; remove the back and reinstall. Refer to Replacing a Back work instruction for details if needed. 13. If repairing a style that uses the center extension spring, extend the legrest and connect the spring. Make sure to orient this spring with the open end of the front hook facing toward the seat. Refer to image at top right. 3. After you verify that both sets of brackets are completely engaged, lock the back brackets using a slotted screwdriver to push down the locking levers. 4. Smooth the outside back cover over the back, pulling the cover tight. Firmly press the fastening tape on the back cover to the fastening tape on the bottom edge of the rear seat rail. 5. Repeat steps 1 through 4 until all backs are installed. 6. Verify the mechanism operation and make adjustments as needed. Pour l assistance en français, appelez votre représentante de service à la clientèle. 7 of 7

Tools Required: Materials Identification and Segregation: Disassembly Steps: Aeron Disassembly for Recycling

Tools Required: Materials Identification and Segregation: Disassembly Steps: Aeron Disassembly for Recycling Y Aeron Disassembly for Recycling Tools Required: Power Driver 2 lbs Hammer Torx Bit Safety Glasses Rubber Mallet Materials Identification and Segregation: Where possible, plastic components are marked

More information

RBP-1215B-RX DODGE RAM QUAD CAB RX3

RBP-1215B-RX DODGE RAM QUAD CAB RX3 RBP-1215B-RX3 2002-2017 DODGE RAM 15-3500 QUAD CAB RX3 Passenger side RX-3 Side Step Drill Template Passenger side rear Modular Bracket (6) L Support Brackets Driver side rear Modular Bracket Driver side

More information

C4 Fabrication Rock Slider Installation 14+ 5th Gen 4Runner w/o KDSS

C4 Fabrication Rock Slider Installation 14+ 5th Gen 4Runner w/o KDSS C4 Fabrication Rock Slider Installation 14+ 5th Gen 4Runner w/o KDSS Thank you for your purchase of the C4 Fabrication s 5th Gen 4Runner Rock Sliders! This product was carefully crafted to ensure a perfect

More information

INSTALLATION INSTRUCTIONS DODGE RAM 2 & 4WD 1500 PART # P5058

INSTALLATION INSTRUCTIONS DODGE RAM 2 & 4WD 1500 PART # P5058 INSTALLATION INSTRUCTIONS 2009-13 DODGE RAM 2 & 4WD 1500 PART # P5058 PARTS LIST: Qty Description Qty Description 1 Grille Guard 12 12-1.75mm Hex Nuts 2 Upper Frame Mounting s (for trucks without tow hooks

More information

TorqueMaster Replacement Spring

TorqueMaster Replacement Spring TorqueMaster Replacement Spring Installation Instructions NOTE: Use these installation instructions in conjunction with the TorqueMaster Repair / Replacement Spring Program literature. Copyright 999 Wayne-Dalton

More information

7878 K940. Checkpoint Antenna. Kit Instructions. Issue B

7878 K940. Checkpoint Antenna. Kit Instructions. Issue B 7878 K940 Checkpoint Antenna Kit Instructions Issue B Revision Record Issue Date Remarks A July 7, 2009 First issue B Nov2013 Revised the Checkpoint installation procedures for 7878 and 7874 scanners Added

More information

Installation Guide Installation Kit for Mounting Philips MP20/30/40/50 on Datex-Ohmeda Aisys Anesthesia Machine

Installation Guide Installation Kit for Mounting Philips MP20/30/40/50 on Datex-Ohmeda Aisys Anesthesia Machine Installation Guide Installation Kit for Mounting Philips MP20/30/40/50 on Datex-Ohmeda Aisys Anesthesia Machine The purpose of this guide is to: 1. Describe mounting of Counterweight (page 2). 2. Describe

More information

Side Mount INSTRUCTION BOOKLET #C122 BED STYLE: PARK CITY

Side Mount INSTRUCTION BOOKLET #C122 BED STYLE: PARK CITY Side Mount BED STYLE: PARK CITY INSTRUCTION BOOKLET #C1 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION PROCESS COULD RESULT

More information

SAM. Model: STV-C65 LCD Mobile Visualized Stand Instruction Manual. Weight Capacity: 1251bs / 56.7kg Suits LCD Flat Panel Display: 42"-55" Page 20

SAM. Model: STV-C65 LCD Mobile Visualized Stand Instruction Manual. Weight Capacity: 1251bs / 56.7kg Suits LCD Flat Panel Display: 42-55 Page 20 SAM Model: STV-C65 LCD Mobile Visualized Stand Instruction Manual Weight Capacity: 1251bs / 56.7kg Suits LCD Flat Panel Display: 42"-55" 20 Step 6 LCD Mobile Lift Stand Model: STV-C65 Cable management

More information

EmagiKit. Privacy Pod Plus. Quiet. Easy. Affordable. INSTRUCTIONS ASSEMBLY

EmagiKit. Privacy Pod Plus. Quiet. Easy. Affordable. INSTRUCTIONS ASSEMBLY EmagiKit Privacy Pod Plus Quiet. Easy. Affordable. INSTRUCTIONS ASSEMBLY DIMENSIONS AND COMPONENTS 47 47 Ceiling Unit 2-B 2-L 2-R Glass Door Corner Trim Door Handle 90 Adjustable Height Work Surface 1-B

More information

PORTA~TRACE. GAGNE, INC. 41 Commercial Dr. Johnson City, New York Phone: Fax: ASSEMBLY INSTRUCTIONS

PORTA~TRACE. GAGNE, INC. 41 Commercial Dr. Johnson City, New York Phone: Fax: ASSEMBLY INSTRUCTIONS PORTA~TRACE GAGNE, INC. 41 Commercial Dr. Johnson City, New York 13790 Phone: 1-607-729-3366 Fax: 1-607-729-7644 ASSEMBLY INSTRUCTIONS PORTA~TRACE MODEL 2436T LIGHT TABLE PORTA~TRACE MODEL 3648T LIGHT

More information

Hardware and Components:

Hardware and Components: Hardware and Components: (A) 5/16 x 2 Hex Bolt (B) 5/16 x 2-1/4 Hex Bolt (C) 5/16 x 2-1/2 Hex Bolt (D) 4X 5/16 x 3/4 Hex Bolt (E) 4X 5/16 x 1-1/4 Hex Bolt (F) 11X 5/16 Flat Washer (G) 12X 5/16 Nylock Nut

More information

INSTALLATION INSTRUCTIONS GRILLE GUARD RAM 1500 PART # 5058/5058-2

INSTALLATION INSTRUCTIONS GRILLE GUARD RAM 1500 PART # 5058/5058-2 INSTALLATION INSTRUCTIONS GRILLE GUARD PART # 5058/5058-2 PARTS LIST: Qty Description Qty Description 1 Grille Guard 8 12-1.75mm x 35mm Hex Bolts 2 Upper Frame Mounting s (for trucks without tow hooks

More information

Fig. 1 Fig. 2. Fig. 3 Fig. 4 TOOLS REQUIRED: *Phillips Screwdriver *Three Inch Putty Knife*Panel Removal Tool *10mm Nut Driver CONTENTS:

Fig. 1 Fig. 2. Fig. 3 Fig. 4 TOOLS REQUIRED: *Phillips Screwdriver *Three Inch Putty Knife*Panel Removal Tool *10mm Nut Driver CONTENTS: *Phillips Screwdriver *Three Inch Putty Knife*Panel Removal Tool *10mm Nut Driver CONTENTS: 2EA. 6X9 TWO WAY SPEAKERS P/N 05030281AA 1EA. INSTRUCTIONS P/N RBI05LXREAR 300c and Charger 1. Remove the lower

More information

Queen Wingback Bed King Wingback Bed

Queen Wingback Bed King Wingback Bed Parts and Hardware List A. Side Rails with Attachment Hooks 2 pcs B. Foot Rail 1 pc C. Head Rail 1 pc D. Center Support Slat 1 pc E. Leg Supports 3 pcs F. Support Slats 4 pcs G. Flat Washers 8 pcs H. Lock

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS SPORTSMAN WINCH MOUNT GRILLE GUARD APPLICATION: 2016-2018 Toyota Tacoma PART NUMBER: 40-93885, 45-93880, 46-23885 ITEM QUANTITY DESCRIPTION TOOLS NEEDED 1 1 WINCH TRAY 15MM SOCKET

More information

Mechanical Frappe Press

Mechanical Frappe Press Mechanical Frappe Press Operation Manual CONTENTS OPERATIONAL INSTRUCTIONS PRECAUTIONS PART NAMES INCLUDED ITEMS BASIC OPERATION MAINTENANCE REPLACEMENT PARTS Thank you for using The Frapptastic Five Mechanical

More information

MANUAL CARTON STAPLER MODEL: H-1025 MANUAL

MANUAL CARTON STAPLER MODEL: H-1025 MANUAL MANUAL CARTON STAPLER MODEL: H-1025 MANUAL WARNING Before operating this stapler familiarize yourself with the safety warnings and instructions in this manual. Keep these instructions with the stapler

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS AUTOMOTIVE PRODUCTS, INSTALLATION INSTRUCTIONS PLATINUM 4 OVAL STEP BAR (90 BENT END) APPLICATION: 2010-2015 Dodge Ram 2500/3500 Mega Cab PART NUMBER: 21-3570, 21-3575, 23-3570, 23-3575, 25-3570, 25-3575,

More information

Hardware and Components:

Hardware and Components: Hardware and Components: (A) 4X 5/16 x 1 Carriage Bolt (B) 2X 5/16 x 2-1/4 Carriage Bolt (C) 2X 5/16 x 3-1/4 Hex Bolt (D) 2X 5/16 x 3/4 Hex Bolt (E) 2X 5/16 x 1-1/4 Hex Bolt (F) 5/16 x 2-1/4 Hex Bolt (G)

More information

OWNER S MANUAL CONTENTS. The only table saw fence with Automatic Positioning Control TM

OWNER S MANUAL CONTENTS. The only table saw fence with Automatic Positioning Control TM The only table saw fence with Automatic Positioning Control TM OWNER S MANUAL Please read this owner s manual before use and keep it at hand for reference. Note: The INCRA TS II system consists of three

More information

WILDING WALLBEDS INSTALLATION INSTRUCTION Side Mount

WILDING WALLBEDS INSTALLATION INSTRUCTION Side Mount WILDING WALLBEDS INSTALLATION INSTRUCTION Side Mount For Wallbed models: Do-It-Yourself Insturction booklet C92 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE

More information

Step 1: The larger tower box contains the tower machine, a set of Silver 100 Lid Keys, and a set of Black 002 Coin Box Keys

Step 1: The larger tower box contains the tower machine, a set of Silver 100 Lid Keys, and a set of Black 002 Coin Box Keys 2 3 Step 1: Each tower is shipped as two boxes the large tower box and the smaller stand box. Open each of the boxes and inventory each of the parts before starting assembly to ensure all parts have arrived.

More information

INSTALLATION INSTRUCTIONS GRILLE GUARD 09-ON DODGE RAM PART #

INSTALLATION INSTRUCTIONS GRILLE GUARD 09-ON DODGE RAM PART # INSTALLATION INSTRUCTIONS GRILLE GUARD 09-ON DODGE RAM PART # PARTS LIST: Qty Description Qty Description 1 Grille Guard 8 12-1.75mm x 35mm Hex Bolts 2 Brackets (for trucks without 22 12mm x 30.1mm OD

More information

Replacing the Reciprocator on the SWF Compact Series Machine (601C and 1201C)

Replacing the Reciprocator on the SWF Compact Series Machine (601C and 1201C) Follow the instructions below to replace the reciprocator in the SWF Compact series machines. The tools required can be found in the tool kit that came with the machine. Preparation 1. First, place the

More information

GENUINE PARTS INSTALLATION INSTRUCTIONS

GENUINE PARTS INSTALLATION INSTRUCTIONS GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: PART NUMBER: Running Boards Kit Nissan Pathfinder/ Infiniti QX60 999T6 X5060 (Pathfinder Running Board Kit) 999T6 R5060 (Infiniti QX60

More information

SAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.

SAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER. SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions

More information

Customer Notice: Congratulations again on your SawStop purchase, and thank you! -SawStop Tualatin, OR

Customer Notice: Congratulations again on your SawStop purchase, and thank you! -SawStop Tualatin, OR Customer Notice: Congratulations on the purchase of this Sliding Crosscut Attachment. As the owner of a SawStop saw, you are familiar with our high standards for quality, fit and finish. Different from

More information

BY ALIEN TECHNOLOGIES CORP

BY ALIEN TECHNOLOGIES CORP BY ALIEN TECHNOLOGIES CORP Assembly Instructions TopLift Pros YOU MAY ALSO REVIEW OUR ASSEMBLY VIDEO, PLAY AND PAUSE AT YOUR CONVENIENCE. JUST VISIT US AT WWW.TOPLIFTPROS.COM AND GO TO Customer Support

More information

LY5005/ LY5007/

LY5005/ LY5007/ LY5005/3300-000-010 LY5007/3300-000-020 Operation/Maintenance Manual For Parts or Technical Assistance 800-327-0770 Table of Contents Style LY5005 & LY5007/3300-000-010 & 3300-00-020 2-3 Drive Rod Assembly

More information

Topo Freestanding Applications - Private Office

Topo Freestanding Applications - Private Office 4 3 2 Topo Freestanding Applications - Private Office Combo Wrench If you have a problem, question, or request, call your local dealer, or Coalesse at 1.800.627.6770 Or visit our website: www.coalesse.com

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Trans4mer Grille Guard/Winch Mount Kit 645 For Chevrolet Silverado 500HD & 3500 This WARN Trans4mer system can be customized to give your Chevy Silverado a wide variety of looks,

More information

Installation Instructions

Installation Instructions For Medium (15-18.5K) + Heavy duty (22-28.5K) Air Conditioner READ BEFORE INSTALLING UNIT To avoid risk of personal injury, property damage, or product damage due to the weight of this device and sharp

More information

LEG CURL IP-S1315 INSTALLATION INSTRUCTIONS

LEG CURL IP-S1315 INSTALLATION INSTRUCTIONS LEG CURL IP-S35 INSTALLATION INSTRUCTIONS Copyright 2009. Star Trac by Unisen, Inc. All rights reserved, including those to reproduce this book or parts thereof in any form without first obtaining written

More information

TASK: Replace Control Mechanism/Drive End for G71 Supervue/Everglide Vertical headrail

TASK: Replace Control Mechanism/Drive End for G71 Supervue/Everglide Vertical headrail 1. Locate the clear plastic louver stems where louvers are attached. 2. Rotate louvers open. Slide a hard plastic card between the louver and the long side of the louver stem. Push the card and louver

More information

Diva Acoustical Ceiling

Diva Acoustical Ceiling Installation Instructions Diva Acoustical Ceiling CONTENTS Important User Information...........................2 Safety Precautions.................................3 Required Tools....................................3

More information

IDR assembly instructions:

IDR assembly instructions: IDR assembly instructions: Required Tools: 2 X 12mm Open End Wrench 14mm open end wrench #2 Phillips Head Screw Driver (Drill with adjustable torque clutch recommended) 8mm nut driver (Supplied in IDR-AK)

More information

INSTRUCTION BOOKLET #C10 Watch step by step installation instructions at: https://www.wallbedsbywilding.com/wallbed-installation-studio-series/ WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY.

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS R5 STEP BOARD APPLICATION: 2009-2017 Dodge Ram 1500 Quad / Crew Cab 2010-2017 Dodge Ram 2500/3500 Crew Cab PART NUMBER: 28-51040, 28-51045, 28-51050, 28-51055 ITEM QUANTITY DESCRIPTION

More information

WEIGHT ADJUSTABLE ESPREE. Model 2ESP-WA-C48- Model 2ESP-WA-C60- 2ESP-WA Rev B 8/17 ASSEMBLY AND OPERATION

WEIGHT ADJUSTABLE ESPREE. Model 2ESP-WA-C48- Model 2ESP-WA-C60- 2ESP-WA Rev B 8/17 ASSEMBLY AND OPERATION WEIGHT ADJUSTABLE ESPREE PNEUMATIC TABLE BASE 2ESP-WA Rev B 8/17 Model 2ESP-WA-C48- Model 2ESP-WA-C60- = SLV, BLK or WHT ASSEMBLY AND OPERATION PARTS AND TOOLS PLEASE REVIEW these instructions before beginning

More information

MM340 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS

MM340 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS MM30 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS Please read this entire manual before you begin. Do not unpack any contents until you verify all requirements on PAGE.

More information

PERSONAL RECORD KEEPING

PERSONAL RECORD KEEPING 2 P R O 3 7 0 A s s e m b l y i n s t r u c t i o n s PERSONAL RECORD KEEPING Tip: Record the serial numbers of your Octane Fitness elliptical in the spaces below. This will make it easier for you to obtain

More information

M ACS Instructions

M ACS Instructions APPLICABLE MODELS: Nissan Frontier 2005 and up short bed with Utili-Trak mounting rails PACKAGE CONTENTS 00-0060-M-01-1205 ACS Instructions Leitner Designs 25675 Taladro Circle Unit E Mission Viejo, CA

More information

INSTALLATION MANUAL. All Recessed Wall-Mount Modules Front-Loading, Rear-Loading, Parcel-Only, Collection Box, Trash/Recycling Bin

INSTALLATION MANUAL. All Recessed Wall-Mount Modules Front-Loading, Rear-Loading, Parcel-Only, Collection Box, Trash/Recycling Bin INSTALLATION MANUAL All Recessed Wall-Mount Modules Front-Loading, Rear-Loading, Parcel-Only, Collection Box, Trash/Recycling Bin TABLE OF CONTENTS GENERAL INFORMATION AND ADVISORIES 3 USPS INSTALLATION

More information

How To Measure Your Finished Opening

How To Measure Your Finished Opening 3000 Series Bifold Doors How To Measure Your Finished Opening MEASURE FROM RIGHT TO LEFT 2 PLACES (WIDTH) MEASURE FROM TOP TO BOTTOM 2 PLACES (HEIGHT) Tools Required for Assembly: Tools Needed: Phillips

More information

INSTALLATION GUIDE. Model:B60 RECESSED IN WALL MOUNT

INSTALLATION GUIDE. Model:B60 RECESSED IN WALL MOUNT INSTALLATION GUIDE Model:B60 RECESSED IN WALL MOUNT Features: Installs between 16 (406mm) wood stud centers Mounting Pattern Compliance: VESA 100*100mm up to 600 x 400mm Level 5 degree horizontal adjustment

More information

Instructions. (a) Upper Chair Assembly. (b) Chair Base

Instructions. (a) Upper Chair Assembly. (b) Chair Base Instructions (a) Upper Chair Assembly (b) Chair Base. Open carton and remove chair base from shipping tray.. Place chair base on the floor in an upright position. 3. Remove upper chair assembly from carton

More information

3/8-16 x 3/4 cap screw. 3/8-16 hex nut for above screws. 1/4-20 x 3/4 socket cap screw. 3/16 short arm hex key (not to scale)

3/8-16 x 3/4 cap screw. 3/8-16 hex nut for above screws. 1/4-20 x 3/4 socket cap screw. 3/16 short arm hex key (not to scale) Super Slab Roller 24, 30 and 36 models Worktable Assembly Directions P.O. Box 89 Cheney, WA 99004 USA 509.235.9200/800.23.7896 Fax: 509.235.9203 www.northstarequipment.com Revised September, 2006. All

More information

HONDA RIDGELINE (KIT #601) Installation Instructions (to be used in addition to owners manual)

HONDA RIDGELINE (KIT #601) Installation Instructions (to be used in addition to owners manual) HONDA RIDGELINE (KIT #601) Installation Instructions (to be used in addition to owners manual) IMPORTANT NOTE: Read before beginning installation. These instructions replace all of Step 1 of the instructions

More information

INSTRUCTION BOOKLET #C0 Watch step by step installation instructions at: https://www.wallbedsbywilding.com/wallbed-installation-studio-series/ WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY.

More information

MODEL SK61732 COMPRESSOR SERVICE KIT

MODEL SK61732 COMPRESSOR SERVICE KIT MODEL SK61732 COMPRESSOR SERVICE KIT For use on 607 and 617 Model Compressors with.32 Stroke WARNING: Unplug the compressor before beginning disassembly. CAUTION: Improper assembly or use of damaged parts

More information

MEC Auto-Mate Assembly Manual. For MEC 9000G/GN and 8567 Grabber Series

MEC Auto-Mate Assembly Manual. For MEC 9000G/GN and 8567 Grabber Series MEC Auto-Mate Assembly Manual For MEC 9000G/GN and 8567 Grabber Series Thank you We really appreciate your support of our product line. But our commitment to you hardly ends here. We won't be satisfied

More information

SM-RAZOR-ART2-L / SM-RAZOR-ART2-XL

SM-RAZOR-ART2-L / SM-RAZOR-ART2-XL SM-RAZOR-ART2-L / SM-RAZOR-ART2-XL Strong Razor Series Articulating Mount for Large and Extra Large Displays INSTRUCTION MANUAL Installation Manual Warnings: Installation of this product should be done

More information

INSTRUCTION BOOKLET #34. For Wallbed models: KING SIZE SIERRA WITH STORAGE HEADBOARD

INSTRUCTION BOOKLET #34. For Wallbed models: KING SIZE SIERRA WITH STORAGE HEADBOARD For Wallbed models: KING SIZE SIERRA WITH STORAGE HEADBOARD INSTRUCTION BOOKLET #34 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION

More information

TYGER GUARD. Parts List BEFORE INSTALLATION WARNING TG-GD6D /7. Tyger Guard. Tube Brackets (Bull Bar) passenger or driver side

TYGER GUARD. Parts List BEFORE INSTALLATION WARNING TG-GD6D /7. Tyger Guard. Tube Brackets (Bull Bar) passenger or driver side TYGER GUARD TM BEFORE INSTALLATION TG-GD6D60068 READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. REMOVE CONTENTS FROM BOX AND VERIFY ALL PARTS ARE PRESENT. ASSISTANCE IS RECOMMENDED. CUTTING IS

More information

Assembled Ez2 Positioning/Operating Instructions

Assembled Ez2 Positioning/Operating Instructions Assembled Ez2 Positioning/Operating Instructions Step 1: Remove packaging material from unit. Report any damage to trucking company as soon as possible. Strap Unit Hand Truck Step 2: Remove unit from skid.

More information

Mighty Mo GX Series Cabinet Installation Guide. OR Rev /11

Mighty Mo GX Series Cabinet Installation Guide. OR Rev /11 Mighty Mo GX Series Cabinet Installation Guide OR-71601787 Safety and Warning ATTENTION The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating

More information

Modular Drawer & Door Systems Installation Instructions Locking Drawers and Receding Doors

Modular Drawer & Door Systems Installation Instructions Locking Drawers and Receding Doors Modular Drawer & Door Systems Installation Instructions ocking Drawers and Receding Doors Pre-Installation Before you begin installation: 1. Read through the installation procedure before starting the

More information

GlideRite Retractable Cover System For HotSpring & Tiger River Spas (except Classic & pre-2000 Landmark Spas)

GlideRite Retractable Cover System For HotSpring & Tiger River Spas (except Classic & pre-2000 Landmark Spas) List of Contents Quantity Description 12 #10 x 1 ½ Flat Head Phillips Screw (see pg. 2) 2 #10 x ½ Pan Head Phillips Screw (see pg. 2) 8 ¼ x 2 ½ Lag Bolt (see pg. 2) 7 ¼ 20 x 5 / 8 Hex Head Bolt (see pg.

More information

The Bowflex Revolution XP Home Gym Assembly Instructions. P/N: Rev ( /0 )

The Bowflex Revolution XP Home Gym Assembly Instructions. P/N: Rev ( /0 ) P/N: 001-7057 Rev ( /0 ) The Bowflex Revolution XP Home Gym Assembly Instructions 2 Table of Contents Before You Start... 2 Tools You Will Need / Hardware Contents... 3 Box Contents... 6 Assembling Your

More information

Sales & Service. JFK - Just For Kids. sasportonline.com. 135 Forestview Road 7879 Will Rogers Blvd.

Sales & Service. JFK - Just For Kids. sasportonline.com. 135 Forestview Road 7879 Will Rogers Blvd. Sales & Service sasportonline.com SA Sport (Canada) SA Sport (U.S.A.) 135 Forestview Road 7879 Will Rogers Blvd. P.O. Box 40 Fort Worth, Texas Orillia, Ontario USA 76140 Canada L3V 6H9 Telephone: (705)

More information

OPERATOR'S MANUAL 46" SNOW BLADE. Model Numbers OEM IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY

OPERATOR'S MANUAL 46 SNOW BLADE. Model Numbers OEM IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY OPERATOR'S MANUAL 46" SNOW BLADE Model Numbers 190-833-OEM IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY MTD PRODUCTS INC. P.O. BOX 368022 CLEVELAND, OHIO 44136-9722 PRINTED IN U.S.A. FORM NO.

More information

KIT ASSEMBLY INSTRUCTIONS

KIT ASSEMBLY INSTRUCTIONS JUMPING JACK TRAILER KIT KIT ASSEMBLY INSTRUCTIONS A torque wrench (provided in the in-store tool kit) is required to assemble this trailer kit. Torque is a twisting (ft.-lb.).copy force measured in foot-pounds

More information

TITAN2-EDGE Public Access Computer Station Dual Track

TITAN2-EDGE Public Access Computer Station Dual Track TITAN2-EDGE Public Access Computer Station Dual Track TITAN2-EDGE Rev A 6/17 Model TITAN2-EDGE ASSEMBLY AND ADJUSTMENT TITAN2-EDGE PARTS AND TOOLS PLEASE REVIEW these instructions before beginning the

More information

Installation Instructions

Installation Instructions edium + Heavy duty READ BEFORE INSTALLING UNIT Preliminary instructions: 1. Check window opening size: the mounting parts furnished with this air conditioner are made to install in a wooden sill double-hung

More information

INSTRUCTION BOOKLET #C20

INSTRUCTION BOOKLET #C20 INSTRUCTION BOOKLET #C0 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION PROCESS COULD RESULT IN SEVERE PERSONAL INJURY TO

More information

READ BEFORE INSTALLING UNIT INSTALLATION WARNINGS AND CAUTION

READ BEFORE INSTALLING UNIT INSTALLATION WARNINGS AND CAUTION edium + Heavy duty READ BEFORE INSTALLING UNIT INSTALLATION WARNINGS AND CAUTION Carefully read the installation manual before beginning. Pay attention to danger and safety notices. be exposed: Carefully

More information

Assembly Instructions and Parts Manual JPSF-1 Fence and JPSR Rail Set

Assembly Instructions and Parts Manual JPSF-1 Fence and JPSR Rail Set Assembly Instructions and Parts Manual JPSF-1 Fence and JPSR Rail Set WALTER MEIER (Manufacturing) Inc. 427 New Sanford Road LaVergne, Tennessee 37086 Part No. M-708482 Ph.: 800-274-6848 Revision C2 02/2013

More information

Models 2230 and 2240

Models 2230 and 2240 Models 2230 and 2240 Overview... 2 Tools Needed... 2 Hardware...3 Assembly... 4-13 Installation... 14 Drawer Removal... 15 Operation... 15 Maintenance... 15 Accessories... 16 Limited Warranty... 16 Perform

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS SNYPER TUBULAR FENDERS APPLICATION: 2007-2017 Jeep Wrangler JK PART NUMBER: 62-1005, 62-1015 ITEM QUANTITY DESCRIPTION TOOLS NEEDED 1,2 2 FRONT FENDERS, DRIVER (1) AND PASSENGER

More information

ASSEMBLY AND CARE INSTRUCTIONS JUST FOR KIDS 355

ASSEMBLY AND CARE INSTRUCTIONS JUST FOR KIDS 355 ASSEMBLY AND CARE INSTRUCTIONS VERSION: 8920100 (Revised 06/16) JUST FOR KIDS 355 SALES AND SERVICE spiethamerica.com Canada and International 135 Forestview Road, PO Box 40 Orillia, Ontario, Canada L3V

More information

MULTI-ACTIVITY PLAY TABLE

MULTI-ACTIVITY PLAY TABLE ASSEMBLY INSTRUCTIONS! WARNING: CHOKING HAZARD - Small parts. Not for children under 3 years.! CAUTION: Adult assembly required. C 2006 Melissa and Doug, Inc. All Rights Reserved www.melissaanddoug.com

More information

Series 4 HV Single Monitor Lift Assembly Instructions

Series 4 HV Single Monitor Lift Assembly Instructions 6703 Zinser Street Schofield, WI 54476 6/13/17 Series 4 HV Single Monitor Lift Assembly Instructions Read all the instructions before beginning. Hardware Pack # 53368 Page1 OF 6 Tools Required for Assembly:

More information

Removing the Z-Axis lead screw

Removing the Z-Axis lead screw Page 1 of 8 TITLE: Sabre Z-Axis Lead Screw Replacement Procedure Gerber FastFact #: 5048 Supplied by: Gerber Hardware Support Last Modified: June 14, 2007 Summary: Tools used: The following procedure explains

More information

SmartView Mounting Frame 3 Wide x 3 Deep Video Wall Display Installation Guide

SmartView Mounting Frame 3 Wide x 3 Deep Video Wall Display Installation Guide SmartView Mounting Frame 3 Wide x 3 Deep Video Wall Display Installation Guide WMK-034 This display kit mounts ViewSonic 46 Video Wall displays in a 3 wide by 3 deep landscape configuration. The frame

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS For Wallbed models: Do-It-Yourself BOOKLET #C90 WARNING! ALL MURPY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION

More information

FRONT BUMPER KIT P/N APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Instr Rev Page 1 of 6

FRONT BUMPER KIT P/N APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Instr Rev Page 1 of 6 FRONT BUMPER KIT P/N 2882301 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please retain these

More information

https://www.wallbedsbywilding.com/wallbed-installation-studio-series/

https://www.wallbedsbywilding.com/wallbed-installation-studio-series/ For Wallbed models: KING SIZE INSTRUCTION BOOKLET #C1 Watch step by step installation instructions at: https://www.wallbedsbywilding.com/wallbed-installation-studio-series/ WARNING! ALL MURPHY/WALLBED

More information

ABM International, Inc. Navigator Assembly Manual

ABM International, Inc. Navigator Assembly Manual ABM International, Inc. 1 1.0: Parts List Tablet (Qty. 1) Tablet mount (Qty. 1) NOTE: Mount may appear and operate different then image below Control Box (Qty. 1) Motor Power Supply (Qty. 1) 2 X-axis motor

More information

Installation Instructions

Installation Instructions For Medium (15-18.5K) + Heavy duty (-8.5K) Air Conditioner READ BEFORE INSTALLING UNIT To avoid risk of personal injury, property damage, or product damage due to the weight of this device and sharp edges

More information

Bushwacker Jeep Flat Style Fender Flares Front Pair

Bushwacker Jeep Flat Style Fender Flares Front Pair Bushwacker Jeep Flat Style Fender Flares Front Pair Note: These instructions involve cutting parts of your vehicle. Please read all instructions prior to starting. Installation Time: 3-4 Hours Tools Required:

More information

Technical Procedure. HIITMill (X) Push/Pull Brake Cable Install

Technical Procedure. HIITMill (X) Push/Pull Brake Cable Install HIITMill (X) Push/Pull Brake Cable Install Applies to: HIITMill and HIITMill X Required Tools: 2.5mm Allen Key 3mm Allen Key 4mm Allen Key 5mm Allen Key 6mm Allen Key 10mm Wrench 10mm Socket Ratchet Needle

More information

INSTALLATION INSTRUCTIONS WINCH MOUNTING KIT Part Number: Application: Kymco MXU 250

INSTALLATION INSTRUCTIONS WINCH MOUNTING KIT Part Number: Application: Kymco MXU 250 INSTALLATION INSTRUCTIONS WINCH MOUNTING KIT Part Number: 72008 Application: Kymco MXU 250 Your safety, and the safety of others, is very important. To help you make informed decisions about safety, we

More information

Star Trac Turbo Trainer Assembly & Setup

Star Trac Turbo Trainer Assembly & Setup Star Trac Turbo Trainer Use the following procedures to unpack and assemble your Turbo Trainer manufactured by Star Trac. UNPACKING AND PARTS LIST Position the shipping carton so the Heavy End logo is

More information

IN 578. Tools Required. Torque Specification: 10mm Socket 7/16 Socket 1/2 Socket 1/2 Wrench 7/16 Wrench 1/8 Allen Wrench.

IN 578. Tools Required. Torque Specification: 10mm Socket 7/16 Socket 1/2 Socket 1/2 Wrench 7/16 Wrench 1/8 Allen Wrench. Tools Required 2011-C Ford F250/F350 No Drilling into Vehicle is Required 10mm Socket 7/16 Socket 1/2 Socket 1/2 Wrench 7/16 Wrench 1/8 Allen Wrench FL277 x 1 Torque Specification: 1/4 Bolts - 6 Ft Lbs.

More information

Service Bulletin

Service Bulletin Service Bulletin 18-026 April 24, 2018 Version 5 Safety Recall: Left (Driver Side) Second Row Seat Recliner Does Not Lock Supersedes 18-026, dated April 7, 2018 to revise the information highlighted in

More information

GlideRite Retractable Cover System For Hot Spot Spas (SE & SLX only)

GlideRite Retractable Cover System For Hot Spot Spas (SE & SLX only) List of Contents Quantity Description 12 #10 x 1 ½ Flat Head Phillips Screw (see pg. 2) 2 #10 x ½ Pan Head Phillips Screw (see pg. 2) 8 ¼ x 2 ½ Lag Bolt (see pg. 2) 7 ¼ 20 x 5 / 8 Hex Head Bolt (see pg.

More information

CTTR Tire Rack Required tools

CTTR Tire Rack Required tools CTTR Tire Rack Required tools Torque wrench, ratchet, 9/16 socket, tape measure, and square edge. ASSEMBLY REQUIREMENTS *Torque all T-bolt nuts to 35-40 foot pounds. Failure to follow the assembly instructions

More information

Installation Instructions

Installation Instructions DODGE RAM 2500 20K Industry Standard SuperRail Custom Mounting Kit #2336 Gross Trailer Weight (Maximum)...20,000 lbs. Vertical Load Weight (Max. Pin Weight)...5,000 lbs. SYSTEM TOW CAPACITY Please note,

More information

Media Storage Systems Fixed Media Cabinets

Media Storage Systems Fixed Media Cabinets Owner s Manual Media Storage Systems Fixed Media Cabinets Contents 1-Column Fixed Media Storage Cabinet Important User Information...........................2 Safety Precautions.................................3

More information

3 wide x 3 deep Video Wall Display Installation Guide

3 wide x 3 deep Video Wall Display Installation Guide HoverTrack Series 3 wide x 3 deep Video Wall Display Installation Guide VWD-3X3-X462 This display kit mounts NEC X461UN and X462UNS LCD monitors in a 3 wide by 3 deep landscape configuration. The frame

More information

2-Door EXO-Top Roof Rack System

2-Door EXO-Top Roof Rack System Page 1/29 Part 13516.01 2-Door EXO-Top Roof Rack System! WARNING The EXO-Top Roof Rack System is rated to a dynamic 300 lb, evenly distributed load. Further loading could result in serious injury or death.

More information

Table of Content. Sayl Disassembly for Recycling

Table of Content. Sayl Disassembly for Recycling Y Sayl Disassembly for Recycling Table of Content 1. Work Chair Disassembly... 2 2. Side Chair Disassembly...17 3. Work Stool Footring Disassembly... 22 1 Y Sayl Disassembly for Recycling Work Chair Disassembly

More information

Mini Cooper Lock Actuator

Mini Cooper Lock Actuator 2001-2006 Mini Cooper Lock Actuator Replacement This guide is on how to remove the lock actuator from the cars door. Written By: Jem ifixit CC BY-NC-SA www.ifixit.com Page 1 of 13 INTRODUCTION In order

More information

FENDER FLARE INSTALLATION

FENDER FLARE INSTALLATION Customer Support TM FENDER FLARE INSTALLATION TG-FF8C4108 IMPORTANT TYGER only approves the installation according to our instructions with the hardware provided. WARNING Failure to complete the installation

More information

Removing and Replacing the Y-truck

Removing and Replacing the Y-truck Service Documentation Removing and Replacing the Y-truck To remove and replace the Y-truck you will need the following tools: 4mm Allen wrench 12mm stamped flat wrench #2 Phillips screwdriver (magnetic

More information

BMW X5 OEM RUNNING BOARD PART#SBBW

BMW X5 OEM RUNNING BOARD PART#SBBW INSTALLATION INSTRUCTIONS 2014-2016 BMW X5 OEM RUNNING BOARD PART#SBBW-146-74 QTY HARDWARE 1 Driver Side OEM Running Board 1 Passenger Side OEM Running Board 8 Rivet Pin 1 Page Step 1: Verify all parts

More information

F l a t S c r e e n A R M S I n s t a l l a t i o n

F l a t S c r e e n A R M S I n s t a l l a t i o n ITEM NUMBERS (1) #TOACAORG16 (2) #TOACAORG20 (3) #TOACATRP24 (4) #TOACATRP30 (5) #TOACATRPDS (6) #TOACATRPSS TOOLS REQUIRED (1) 3/8 Wrench (not provided) (2) Phillips head screwdriver (not provided) (1)

More information

MantelMount. TM1A Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS

MantelMount. TM1A Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS MantelMount TMA Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS TM Thank you for choosing the MantelMount television wall mount. Please read this entire manual before

More information

Oasis Recliner Disassembly Instructions

Oasis Recliner Disassembly Instructions These instructions may be used to disassemble all versions of our Oasis Recliner seating line and available options. Time Required: 20 minutes. (Internal metal frame) D: Reaching up and inside the back,

More information