Sandwich panel Compartment details, ceiling PRINCIPLE DETAILS 1:1
|
|
|
- Grace Watson
- 6 years ago
- Views:
Transcription
1 Drawing nr Contents of drawing Rev date SPA50--E-EN Joint between panels SPA5--E-EN Ceiling, middle area SPA52--E-EN Ceiling, edge area SPA52--2E-EN Ceiling, edge area SPA52--3E-EN Ceiling, longitudial edge, not fixed SPA52--4E-EN Ceiling, edge area, panel end City sector type, Name and address Block Site/Reg nr File nr Drawing type Contents of drawing Sandwich panel Compartment details, ceiling Nr : Ruukki Construction Oy Vimpelintie 66 tel FI ALAJÄRVI fax FINLAND wwwruukkicom Designer Ruukki Checked PRINCIPLE DETAILS Work nr Work nr Drw nr Rev
2 ceiling Joint between panels Rev date Work nr Drawing nr Rev Rev SPA50--E-EN Ruukki File nr :2,5 SPA50--E-ENdwg 33 THICKNESS CLASS: 80, 25, 50, 75, 200 AND 230 mm THICKNESS CLASS: 00 mm Sandwich panel SPA Screw, d(min) = 4,2 mm, elements are fastened to each other from top suface joints, max distance between fasteners 500 mm 33 Elastic groove joint sealant, installed in the factory Copyright Rautaruukki Oyj Allowed only for designs with Ruukki's products
3 middle area Rev date Work nr Drawing nr Rev Rev SPA5--E-EN A File nr :4 SPA5--E-ENdwg Fire protection wool FPS 7, thickness (mm) Structure EI60 EI90 EI20 EI80 EI Sandwich panel SPA 09 /EAHP3/ Hat purlin 3 /EAR8/ Cover flashing Flashing screw c/c 300 mm 28 Threaded rod M2 /EA3SS40/ Sealing band 3 /EAWS30565/ Mineral wool /EAFW / Fire protection wool Copyright Rautaruukki Oyj Allowed only for designs with Ruukki's products
4 edge area Rev date Work nr Drawing nr Rev Rev SPA52--E-EN A File nr :4 SPA52--E-ENdwg Fire protection wool FPS 7, thickness (mm) Structure EI60 EI90 EI20 EI80 EI240 Fire protection of column according to structural designer Sandwich panel SPA /EAFC/ Fastening corner flashing 3 /EAR8/ Cover flashing 58 /EAR23/ Cover flashing 20 Self-drilling panel screw, washer with sealing 23 Fastener for flashing, washer with sealing Flashing screw c/c 300 mm /EA3SS40/ Sealing band 3 /EAWS30565/ Mineral wool /EAFW / Fire protection wool 08 Copyright Rautaruukki Oyj Allowed only for designs with Ruukki's products
5 edge area Rev date Work nr Drawing nr Rev Rev SPA52--2E-EN A File nr :4 SPA52--2E-ENdwg Fire protection wool FPS 7, thickness (mm) Structure EI60 EI90 EI20 EI80 EI240 Fire protection of column according to structural designer Sandwich panel SPA 3 /EAR8/ Cover flashing 58 /EAR23/ Cover flashing 20 Self-drilling panel screw, washer with sealing 23 Fastener for flashing, washer with sealing Flashing screw c/c 300 mm /EA3SS40/ Sealing band 3 /EAWS30565/ Mineral wool /EAFW / Fire protection wool 58 Support according to structural designer Copyright Rautaruukki Oyj Allowed only for designs with Ruukki's products
6 longitudial edge, not fixed Rev date Work nr Drawing nr Rev Rev SPA52--3E-EN A File nr :4 SPA52--3E-ENdwg Fire protection wool FPS 7, thickness (mm) Structure EI60 EI90 EI20 EI80 EI Sandwich panel SPA 52 /EAR9/ Cover flashing 53 /EAIC2/ Internal corner flashing Flashing screw c/c 300 mm /EA3SS40/ Sealing band 3 /EAWS30565/ Mineral wool /EAFW / Fire protection wool Copyright Rautaruukki Oyj Allowed only for designs with Ruukki's products
7 edge area, panel end Rev date Work nr Drawing nr Rev Rev SPA52--4E-EN A File nr :4 SPA52--4E-ENdwg Fire protection wool FPS 7, thickness (mm) Structure EI60 EI90 EI20 EI80 EI Fire protection of column according to structural designer Sandwich panel SPA 4 External corner flashing, according to project 58 /EAR23/ Cover flashing 20 Self-drilling panel screw, washer with sealing Flashing screw c/c 300 mm /EA3SS40/ Sealing band 3 /EAWS30565/ Mineral wool /EAFW / Fire protection wool Copyright Rautaruukki Oyj Allowed only for designs with Ruukki's products
Drawing nr. Contents of drawing Date Rev. date
Contents of drawing date SPA30--E-EN Fastening to floor, vertical or horizontal installation 72202 SPA3--E-EN Vertical joint, horizontal installation 72202 605206 SPA3--2E-EN Vertical joint, horizontal
SANDWICH PANEL SPA INSTALLATION INSTRUCTIONS
www.ruukki.com SANDWICH PANEL SPA INSTALLATION INSTRUCTIONS Content Installation directions and fastening of the panels... 3 Weights of the panels... 3 Additional information of the panels... 3 Preparing
MACHINING HOT-ROLLED STEEL PLATES AND COILS
www.ruukki.com MACHINING HOT-ROLLED STEEL PLATES AND COILS This brochure compiles information on machining our hot rolled steel products, including the following methods: drilling thread cutting sawing
PREFABRICATIONS, PRECISION CUT LENGTHS AND PRECISION CUT PLATES WITH BEVELLED EDGE
www.ruukki.com PREFABRICATIONS, PRECISION CUT LENGTHS AND PRECISION CUT PLATES WITH BEVELLED EDGE HOT-ROLLED STEEL PLATES AND COILS Precision cut lengths and precision cut plates with a bevelled edge are
MECHANICAL BACK FASTENED SYSTEMS INSTALLATION DATA
MECHANICAL BACK FASTENED SYSTEMS INSTALLATION DATA 7/16 PETRARCH ARCHITECTURAL WALL PANELS APPLIED OVER A STUDWALL BY MEANS OF A FIELD ASSEMBLED BACK FASTENED SYSTEM DESIGN CONCEPT 7/16 panels may be installed
Roofs. Installation instructions Models Classic C and D
Roofs Installation instructions Models Classic C and D A complete roof includes a lot more than just the roofin g sheets. A combination of lead-ins, water removal systems, ladders, roof bridges and snow
Roofs. Installation instructions Models Monterrey and Elite
Roofs Installation instructions Models Monterrey and Elite A complete roof includes a lot more than just the roofing sheets. A combination of lead-ins, water removal systems, ladders, roof bridges and
ASSEMBLY INSTRUCTION CONTENT
ASSEMBLY INSTRUCTION CONTENT 1. Main information...2 2. Opening 20 move type container...4 3. Assembly 20 move type container...6 1 1. MAIN INFORMATION Tools and materials for assembling are needed: 1.
Construction details: Master-C type profiles and joints:
Construction details: Master-C type profiles and joints: Master-C 3g 32 mm. (1 1/4 ) 1000 mm. (39 3/8 ) outer face inner face 10.5 fixing details: sealing washers shall be installed through a 2-3/8 x 1-9/16
dimensional and shape tolerances HOT-ROLLED STEEL PLATES AND COILS
www.ruukki.com dimensional and shape tolerances HOT-ROLLED STEEL PLATES AND COILS Scope The dimensional and shape tolerances of steel are determined by the requirements of the materials standard or the
IOM 004 Effective 3/29/04 Rev A. MULTI-VENT Laminar Flow Panels Installation Operation and Maintenance
IOM 004 Effective 3/29/04 Rev A MULTI-VENT Laminar Flow Panels Installation Operation and Maintenance Contents Batten Arrangements...3 Slip-On Battens...4 Ceiling Opening...5 Installation...5 Hanger Bracket
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS A CSW Industrials Company FR and FRE Roof Expansion Joint Covers IMPORTANT The following instructions are very important. Read them carefully, and be sure you understand them
ALL SEASON PATIO COVER
ALL SEASON PATIO COVER 61 Where the All Season Patio Cover is to be attached to the home, create a level line showing where the top of the mounting rail is to be located. Install each section with the
Wall mounting with holding profile
B Main profile C Edge profile D Wall spacer E Heradesign acoustic panel Edge distance max. 250 mm c Centre distance of basic section (see table) B max. 600 mm or 625 mm a Centre distance of spacer (see
FRP GATES MM08 FRP GATES Rev. 3 COMPOSITE SOLUTION PAGE 1
FRP GATES MM08 08.02.2016 Rev. 3 FRP GATES COMPOSITE SOLUTION PAGE 1 SUMMARY 1. USES AND CHARACTERISTICS... 3 2. EMPLOYMENT FIELDS... 4 3. MATERIALS... 5 3.1 TABLE OF PROFILES AND STRUCTURAL ACCESSORIES...
Austin Standing Seam Awning Assembly and Installation Instructions. Assembly Instructions
Austin Standing Seam Awning Assembly and Installation Instructions Be sure to use safety glasses when assembling and installing the awning. Some metal parts may have sharp edges. Use work gloves to handle
Instructions for Installation on a Pitched Roof LIGHTWAY optical tube LW 260, LW 320, LW 520, LW 760
Lightway, s.r.o. Registered office: Ledvinova 1714, 149 00 Praha 4 Offices: Za Humny 1054/4a, 161 00 Praha 6 tel.: 235 300 694, fax: 235 300 218 Company ID No.: 63669366, Tax ID No.: CZ63669366 Bank: KB
Instructions for Installation on a Flat Roof
Lightway, s.r.o. Registered office: Ledvinova 1714, 149 00 Praha 4 Offices: Za Humny 1054/4a, 161 00 Praha 6 tel.: 235 300 694, fax: 235 300 218 Company ID No.: 63669366, Tax ID No.: CZ63669366 Bank: KB
KEITH PANEL SYSTEMS FUNDERMAX- MAX EXTERIOR EXPOSED FASTENER PRESSURE EQUALIZED WALL SYSTEM
S Y S T E M D E T A I L S FUNDERMAX- MAX EXTERIOR EXPOSED FASTENER PRESSURE EQUALIZED WALL SYSTEM PAGE TITLE PAGE Table of Contents Fundermax Max Exterior Product Information Design and Installation Information
Hang-TITE Rod Hanger Screws
Description The Hang-TITE Rod Hanger Screw is a one-piece, internally threaded anchor designed for suspending threaded rod for applications like cable-tray, pipe hanging, fire protection, and electrical
vacon nxs/p ac drives flange mounting kit for fr7-fr9 installation manual
vacon nxs/p ac drives flange mounting kit for fr7-fr9 installation manual 2 vacon Flange mounting kit FR7-FR9 INDEX Document code: DPD01880B Date: 02.10.2017 1. General... 2. Vacon Flange Mounting Kit
BUTCHER BLOCK MICROWAVE OVEN STAND
BUTCHER BLOCK MICROWAVE OVEN STAND 828 The butcher block has fallen out of favor in recent years, replaced by the countertop cutting board in an attempt to save space. This design, however, makes the butcher
WALL TO FABRICATED FLOOR
WALL TO FABRICATED FLOOR PERIMETER WALL IS HELD IN PLACE BY WOODEN STRIP SCREED OPTIONAL NSF COVED FLOOR IS SHOWN PARTITION WALL IS HELD IN PLACE BY WOODEN STRIP SCREED OPTIONAL NSF COVED FLOOR IS SHOWN
TECHNICAL GUIDE BEONSTONE PANELIZED STONE SIDING
TECHNICAL GUIDE BEONSTONE PANELIZED STONE SIDING TABLE OF CONTENTS This installation guide provides detailed step-by-step instructions for do-it-yourself projects. We invite you to read it carefully and
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS SHOWER DOOR KIT ALUMINUM 2503 E. Vernon Avenue, Los Angeles, CA 90058-1826 Phone: (800) 421-6144 EXT. 7740 Fax: (800) 458-7496 crlaurence.com Email: showers@crlaurence.com 11M0260
TABLE OF CONTENTS: SHEET 3: REMOTE DRIVER BOX INSTALLATION SHEET 7: OCTAGON JUNCTION BOX INSTALLATION
TABLE OF CONTENTS: SHEET 2: MULLION SYSTEM INSTALLATION SHEET 3: REMOTE DRIVER BOX INSTALLATION SHEET 4: 2 X 4 EXTERIOR TRANSITION PLATE INSTALLATION SHEET 5: 2 X 4 EXTERIOR INSTALLATION SHEET 6: 4 X 4
EXPOSED FASTENING SYSTEM WITH SCREWS OR RIVETS
External EXPOSED FASTENING SYSTEM WITH SCREWS OR RIVETS Parklex Facade may be installed using mechanical fasteners, such as screws or rivets. The panels are attached to vertical battens. In the event that
Ekoroof LiteTile Headwall Flashing Installation Detail
Ekoroof LiteTile Flashing Installation Detail 3/8 2 4 -to-wall fastener is 1 1/2 Tapcon, 1 1/2 Approved Concrete Drive Pin, or 1 1/2 Corrosion Resistant & Approved Screw w/ EPDM washer & Hex or Concealor
Assembly Instructions
Selling Station Assembly Instructions View from above without top A B C D Rounded finished corners on A & D Square unfinished 3-sides on B & C Selling Station Components (2) 2' x 6' Side s Have a channel
1.) Type: VL-F Single compartment rectangular smoke extraction ducts and fittings
1.) Type: VL-F Single compartment rectangular smoke extraction ducts and fittings 2.) Manufacturer / Place of manufacture: AEROPRODUKT Zrt., 6640 Csongrád, Szegedi út 1., HUNGARY 3.) Function: The smoke
Walls Fact Sheets. Partition Walls and Walls Cladding. Perforated Board. Sandwich Board
s Partition and Perforated Board Sandwich Board Please consult Viroc Technical File available at www.viroc.pt, on EN language, on Downloads page. Other Viroc Recommended Solutions files, organized by type
1 IMPORTING GDL-OBJECT...1
GDL-OBJECT TABLE OF CONTENTS 1 IMPORTING GDL-OBJECT...1 2 MTH CONCERTTO -OBJECT...3 2.1. Information-window...3 2.2. Settings-window...3 2.3. Dimensions-window...4 2.4. Mounting frame and screws -window...6
Installation and Operating Instructions. Intake pit with Skandia conveyors (en)
Installation and Operating Instructions Intake pit with Skandia conveyors 408115 (en) ANTTI-TEOLLISUUS OY Koskentie 89 FI-25340 Kanunki, Salo Tel. +358 2 774 4700 Fax +358 2 774 4777 E-mail: antti@antti-teollisuus.fi
KS42 MF SERIES - HORIZONTAL INSTALLATION
CI-DS-01-KSMF H CI-PJ-01-KSMF H CI-PJ-02-KSMF H CI-PJ-03-KSMF H CI-PJ-04-KSMF H CI-PJ-05-KSMF H CI-PJ-06-KSMF H CI-PJ-07-KSMF H CI-PJ-08-KSMF H CI-PJ-09-KSMF H CI-PJ-10-KSMF H CI-PJ-11-KSMF H CI-PJ-12-KSMF
HOLLOW METAL DOOR/WINDOW SYSTEM FOR THERMALSAFE CF WALLS WINDOW ASEMBLY GUIDE PIONEERING INSULATED METAL PANEL TECHNOLOGY
HOLLOW METAL DOOR/WINDOW SYSTEM FOR THERMALSAFE CF WALLS WINDOW ASEMBLY GUIDE PIONEERING INSULATED METAL PANEL TECHNOLOGY PIONEERING INSULATED METAL PANEL TECHNOLOGY TABLE OF CONTENTS DETAIL TITLE PAGE
PRIME SHOWER ENCLOSURE INSTALLATION INSTRUCTIONS
PRIME SHOWER ENCLOSURE INSTALLATION INSTRUCTIONS IMPORTANT DreamLine reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings,
900 SERIES PANEL SHEET INDEX STAGGERED ENDLAP STAGGERED MALE LEG AT ENDLAP CONTINUOUS FEMALE ENDLAP INSTALLATION SEQUENCE CI-WR
900 SERIES PANEL CI-DS-01-900 CI-PJ-01-900 CI-PJ-02-900 CI-EL-01-900 CI-EL-02-900 CI-EL-03-900 CI-EL-04-900 CI-EL-05-900 CI-EL-06-900 CI-EL-07-900 CI-EL-08-900 CI-RD-01-900 CI-RD-02-900 CI-RD-03-900 CI-EV-01-900
calculated with factor of safety of 2.5 for bending stress, 3.0 for shear stresses and deflection limitation of L/180.
Metl-Span CF-42 Light Mesa Wall Panels 26 Ga. Exterior / 26 Ga. Interior Facings Allowable Connection Load 1,7,8,9,10 (psf) for Two or More Equal Spans Panel Type 2 Design Criteria 3,4,5,6 Support Span
FW / FIG Partition Kit(s) Installation Instructions
FW / FIG Partition Kit(s) Installation Instructions This instruction explains how to join 8 in. and 10 in. top piping partitions to FIG and FW merchandisers. Do not remove the shipping braces until the
Column and Beam Fire Protection SYSTEMS 335 INSTALLATION 337 GENERAL REQUIREMENTS 337 FRAMING 337
SYSTEMS 335 INSTALLATION 337 GENERAL REQUIREMENTS 337 FRAMING 337 PLASTERBOARD LAYOUT 337 PLASTERBOARD FIXING 337 CONSTRUCTION DETAILS 341 Column and Beam Fire Protection Column and beam protection systems
FOREPOLING PRODUCT CATALOGUE ROBIT FOREPOLING PRODUCT CATALOGUE ROBIT
ROBIT FOREPOLING PRODUCT CATALOGUE ROBIT FOREPOLING PRODUCT CATALOGUE RoX+ 76,1 systems RoX+ 88,9 systems RoX+ 101,6 systems RoX+ 114,3 systems RoX 139,7 systems RoX+ 168,3 systems RoX+ GFRP 76,1 systems
SecuAnch Roof Anchor System
Height Safety Products Email: marketing@fallprotec.com SecuAnch Roof Anchor System 1 Presentation The SecuAnch lifeline is designed to be permanently installed on buildings and other structures where maintenance
The General Principles of Detailed Design at Ruukki Construction Ltd. Julia Piiroinen
The General Principles of Detailed Design at Ruukki Construction Ltd 1. The feasibilities of production at the workshops 2. Hot-rolled I-profile 2.1. Stiffeners 2.2. End plates 2.3. Lifting 3. Welded I-profile
Ceiling mount for BW1 THEATRE Concept (R ) INSTALLATION MANUAL. Part. No.: R Date: Rev: 01
Ceiling mount for BW1 THEATRE Concept (R9852065) INSTALLATION MANUAL www.cineversum.com Date: 10112008 Rev: 01 Part. No.: R599769 Assembly Instructions: This product is designed to be used in private homes.
AWNING / PATIO COVER INSTALLATION INSTRUCTIONS
AWNING / PATIO COVER INSTALLATION INSTRUCTIONS Before You Begin Read the installation instructions thoroughly before beginning the installation procedure. Perspective In the Awning Instructions, Back means
INSTALLATION AND OPERATING INSTRUCTIONS
Labkotec Oy Labkotie 1 FI-36240 KANGASALA FINLAND Tel. +358 29 006 260 Fax +358 29 006 1260 Internet: www.labkotec.fi 26.09.2008 1 / 5 Capacitive level sensor KAS/3W INSTALLATION AND OPERATING INSTRUCTIONS
Section 3: Understanding Your Shop Drawings Reading Shop Drawing Abbreviations 60" O.A. stands for the overall dimension from the back wall to the front face of achieve your 60" overall you will set the
!When using electrical equipment, basic safety precautions should always be followed, including the following: INSTALLATION INSTRUCTIONS
TABLE OF CONTENTS: SHEET 2: MULLION SYSTEM INSTALLATION SHEET 3: REMOTE DRIVER BOX INSTALLATION SHEET 4: 2 X 4 EXTERIOR WITH TRANSITION PLATE INSTALLATION SHEET 5: 2 X 4 INSTALLATION SHEET 6: 4 X 4 EXTERIOR
CORNERVIEW / FRENCH CORNER
CORNERVIEW / FRENCH CORNER SHOWER ENCLOSURE INSTALLATION INSTRUCTIONS IMPORTANT DreamLine reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date
Installation Instructions
Important 1. Acclimate materials 24 hrs before installation. Maintain temperature controlled environment after installation. 2. Install in accordance with manufacturer s installation instructions. Failure
Double Screen Door Installation Instructions
Double Screen Door Installation Instructions (36) #8x1 tek screws (20) #8x1/2 tek screws Package Includes: (2) PCA Screen Doors (1) Astragal (1) Left Hand Z-bar (1) Right Hand Z-bar (1) Header Z-bar (2)
Extrusions GB-3-IN01. Updated: Scale: REV: - This Drawing is Protected by Copyright Altus NZ Ltd.
Extrusions Updated: N/A Scale: N.T.S REV: - Dwg Dwg Revision Rev No Description Description Date GB-3-IN01 Index Page - - - - - GB-3-001 Extrusions - - - - - GB-3-002 Extrusions - - - - - GB-3-003 Extrusions
VisioGlide 100 System W4F Four doors 2 fixed, 2 sliding
Balcony Systems 2011 Visio Glide W4-F Curved Sliding Doors 4 doors: 2 fixed, and 2 sliding Installation guide 1. Insert silicone into the two bottom corners before closing the frame. 1 2. Connect top and
Table and Furniture Base Fittings Plinth Adjusting Fittings
Adjusting screw with M8 or M thread Rigid, for glide inserts, steel thread Finish/Colour: Black, thread galvanized Version: With acceptance Ø30 mm Thread M8 650.22.381 M 650.22.382 Packing: 1 or 0 pcs.
Top Mount Ultra Modern Hanger
Top Mount Ultra Modern Hanger ASSEMBLY INSTRUCTIONS TOP MOUNT ULTRA MODERN HANGER Recommended Tools Level Tape Measure Pencil Drill with 1/8, and 1/4, Drill Bits and Phillips Bit Socket Wrench with 9/16
Kai Installation Instructions
Kai Installation Instructions Before Beginning Installation Read through the entire instruction thoroughly A minimum of 2 people are required for this assembly These instructions reflect typical assemblies;
INSTALLATION INSTRUCTIONS for Wood/Clad Wood Windows without Exterior Trim or Nailing Fin (JII025) ImpOrTaNT INFOrmaTION & GlOssary.
for Wood/Clad Wood Windows without Exterior Trim or Nailing Fin (JII025) Thank you for selecting JELD -WEN products. Attached are JELD-WEN s recommended installation instructions for metal clad wood windows
JOINT FOR ELLIPTICAL BAR (LUXE) C = Nominal boom length. Rubber bead boom A. ig.1
800TSE JOINT FOR ELLIPTIL R (LUXE) (mm) 114 min. 40 D E = oom section back part = Nominal boom length E = Rubber bead boom = oom section front part D = Rubber bead boom H = eiling height 2586 3036 2696
KS SERIES - VERTICAL INSTALLATION
CS-DS-01-KSV CS DISCLAIMER CS-PJ-01-KSV KS42SL EXPANDED PANEL JOINT CS-PJ-02-KSV KS42SL ENGAGED PANEL JOINT CS-PJ-03-KSV KS45SL EXPANDED PANEL JOINT CS-PJ-04-KSV KS45 FLAT ENGAGED PANEL JOINT CS-PJ-05-KSV
Outdoor Cooler Cart. Outdoor Cooler Cart Construction Instructions
Outdoor Cooler Cart Outdoor Cooler Cart Construction Instructions Make the Legs and Side Panels. Cut the eight long and short leg pieces to length. See Material List on next page.. Apply a bead of glue
Shaft Wall SYSTEMS 210 INSTALLATION 211. Shaft Wall systems are fire rated non-load bearing walls used for shafts and service ducts.
SYSTEMS 210 INSTALLATION 211 GENERAL REQUIREMENTS 211 FRAMING 212 PLASTERBOARD LAYOUT 213 PLASTERBOARD FIXING 214 CONSTRUCTION DETAILS 217 Shaft Wall Shaft Wall systems are fire rated non-load bearing
HIA AIR CARGO HAMILTON ADDENDUM #3. Addendum No. A03 (Architectural) o Text 1 page o SK-10a o SK-10b o SK-11
HIA AIR CARGO HAMILTON ADDENDUM # (This Addendum consists of six () pages) Cover sheet Schedule time lines for Architectural Precast, Miscellaneous Metals, Insulated Metal Panels, Roofing and Aluminum
DBP Technical Data Series Rev. 0 Jan. 1, Pre Assembled Door Canopies
Technical Data Series Revised: 1 January, 2011 Article IX. SECTION 9.01 PERSONAL DOOR CANOPIES...3 SECTION 9.02 ERECTION INSTRUCTIONS...4 SECTION 9.03 ERECTION ILLUSTRATIONS...7 SECTION 9.04 MULL INSTRUCTIONS
Installation Instructions
Important SECTION VIEW 1. Acclimate materials 24 hrs before installation. Maintain temperature controlled environment after installation 2. Install in accordance with manufacturer s installation instructions.
Shetland Stalls Installation Instructions
Shetland Stalls Installation Instructions RAMM Horse Fencing and Stalls 13150 Airport Hwy. Swanton, OH 43558-9615 1-800-434-8456 Rev. 1/9/18 Before you start Kit can accommodate up to 12 wide stall front
SECTION SHEET METAL FLASHING AND TRIM
SECTION 07620 PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Formed roof drainage sheet metal fabrications. 2. Formed low-slope roof sheet metal fabrications. 1.2 SUBMITTALS A. Shop Drawings: Show
Sport-Thieme. Full-Size Goal. Assembly instructions. 7,32x2,44 m, Portable
Assembly instructions Sport-Thieme 7,32x2,44 m, Portable Art.-Nr.: 115 0793 257 7207 Full-Size Goal 0218214 2018 Sport-Thieme GmbH D-38367 Grasleben Germany sport-thieme.com info @sport-thieme.com Phone:
installation manual nx frequency converters flange mounting kit for nxs/p frequency converters fr7-fr9
installation manual nx frequency converters flange mounting kit for nxs/p frequency converters fr7-fr9 vacon Flange mounting kit FR7-FR9 INDEX Document code: ud00877 Date: 11/19/010 1. General.... Vacon
INSTALLATION INSTRUCTIONS SIDELITE ASSEMBLY SERIES 900 TERRACE DOOR AND SERIES 925 PATIO DOOR
INSTALLATION INSTRUCTIONS SIDELITE ASSEMBLY SERIES 900 TERRACE DOOR AND SERIES 925 PATIO DOOR Phone: (800) 262-5151 Fax: (866) 262-3299 crlaurence.com usalum.com crl-arch.com 11M0292 HANDLING, STORAGE,
GlideRite Retractable Cover System For Hot Spot Spas (SE & SLX only)
List of Contents Quantity Description 12 #10 x 1 ½ Flat Head Phillips Screw (see pg. 2) 2 #10 x ½ Pan Head Phillips Screw (see pg. 2) 8 ¼ x 2 ½ Lag Bolt (see pg. 2) 7 ¼ 20 x 5 / 8 Hex Head Bolt (see pg.
20011, F100 - F150 - F250 - F350 P.U. & BRONCO Tools Needed for Installation:
Rev-4 05-24-12 CUT OUT FLARES INSTALLATION INSTRUCTIONS FOR 20011, 20012 F100 - F150 - F250 - F350 P.U. & BRONCO Tools Needed for Installation: Step 1: Painting (A) 3/8 Drill (B) 3/16 Drill Bit (C) 5/16
Big Block Installation Manual For Systems without A/C
Big Block Installation Manual For Systems without A/C Billet Specialties, Inc. 500 Shawmut Ave. La Grange, IL 60526 Tech Line (708) 588-0505 Fax (708) 588-7181 Hardware List For Chevrolet Big Block Tru
HPH Series J-Hook Installation Instructions
HPH Series J- Installation Instructions 1 Mounting to a vertical surface: HPH16, HPH32, HPH48 and HPH64 Use a nail*, bolt* or screw* with a minimum head diameter of 0.329 (1-A) and an appropriate length
A500 ASSEMBLY & INSTALLATION INSTRUCTIONS
ASSEMBLY & INSTALLATION INSTRUCTIONS 1 CONTENTS 2 Component Parts A B Canopy Mounting Plate C Cap (3) D Threaded Nipple E Threaded Standoffs (2) F Anchors (8) G #10 Screws (8) H Safety Cable (2) I Safety
VIGO - COLUMN SYSTEM
VIGO - COLUMN SYSTEM COMPONENTS 6 7 3 2 17 15 12 14 11 13 15 10 16 9 8 1 2 5 1 4 1 - Column system stile 2 - Column system LED cover 3 - Column system cover 4 - Column plug 5 - Column mount 6 - Column
Bedienungsanleitung - Operating Instructions - Mode d emploi
Bedienungsanleitung - Operating Instructions - Mode d emploi LAMINATED BUSBAR MACHINING UNIT 2017 Alfra GmbH II. Industriestraße 10 D-68766 Hockenheim Tel.: +49 (0)6205-3051-0 Fax: +49 (0)6205-3051-150
SHEET METAL FLASHING AND TRIM Christ on the Mountain
SECTION 076200 - SHEET METAL FLASHING AND TRIM PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Compatibly with the bumping of flashings and trim as identified in the Membrane Roofing Section 075000.
METL-VISION WINDOW SYSTEM FOR HORIZONTAL WALL PIONEERING INSULATED METAL PANEL TECHNOLOGY
METL-VISION WINDOW SYSTEM FOR HORIZONTAL WALL Window assembly GUIDE PIONEERING INSULATED METAL PANEL TECHNOLOGY PIONEERING INSULATED METAL PANEL TECHNOLOGY CONTENTS DETAIL TITLE FILE NO. PAGE NO. INTRODUCTION..................................................................
INSTALLATION MANUAL STOREFRONT DOORS
INSTALLATION MANUAL STOREFRONT DOORS www.aluflam-usa.com SYSTEM DESCRIPTION - Extruded and filled aluminum framing, tested and approved by UL - 3-3/8 frame depth - Clear, fire-rated safety glazing - Door
GlideRite Retractable Cover System For HotSpring & Tiger River Spas (except Classic & pre-2000 Landmark Spas)
List of Contents Quantity Description 12 #10 x 1 ½ Flat Head Phillips Screw (see pg. 2) 2 #10 x ½ Pan Head Phillips Screw (see pg. 2) 8 ¼ x 2 ½ Lag Bolt (see pg. 2) 7 ¼ 20 x 5 / 8 Hex Head Bolt (see pg.
SPRINGLOK SPRINGLOK FLASHING SYSTEM PRODUCT BROCHURE ENGINEERED PRODUCT SYSTEMS
FLASHING SYSTEM ENGINEERED PRODUCT SYSTEMS PRODUCT BROCHURE 2 ND EDITION FLASHING SYSTEM FUNCTIONALLY UNIQUE. ENGINEERED PRODUCT SYSTEMS / FLASHING Fry Reglet comprehensive selection of moisture prevention
ATOMIC. ASM Panel Brochure ARCHITECTURAL SHEET METAL,
ATOMIC ARCHITECTURAL SHEET METAL, INC. ASM Panel Brochure 3207 Labore Road Vadnais Heights, MN 55110 Phone: 651-646-1706 Fax: 651-646-1684 atomic@atomicsheetmetal.com 1 of 1Page 0 of 0 ARCHITECTURAL SHEET
1 RANNILA PANEL 3LOCK...2
1.6 SPECIFYING THE PANEL... 14 1.6.1 General... 14 1.6.2 Wind Loads... 15 1.6.2.1 External Walls... 15 1.6.2.2 Double Facades... 15 Structural Systems / Rannila Panel 3Lock 1 RANNILA PANEL 3LOCK...2 1.1
Installation Type. Edge of Door. Pull (Hinge) Side Mounted. Hinge Edge of Door. Push (Stop) Side Mounted
Installation Instructions CAUTION An incorrectly installed or improperly adjusted door closer can cause property damage or personal injury. These instructions should be followed to avoid the possibility
SIMPLER BETTER FASTER
SIMPLER BETTER FASTER 1. FITTING RING BEAMS DETAILS Always work anti-clockwise viewed from outside the roof. Each bar should be sequentially numbered, i.e. 1, 2, 3. Select the ring beam, position the left
INSTALLATION INSTRUCTIONS
EDGE PIVOT DOOR EPDSC0760 EPDSC0800 EPDSC0900 EPDSC1000 ESPSC0760 ESPSC0800 ESPSC0900 ESPSC1000 PIVOT DOOR IN ALCOVE PIVOT DOOR & SIDE PANEL INSTALLATION INSTRUCTIONS IMPORTANT - Please read before installation
RL7035 LED Linear Light - Only for recessed installation
RL7035 LED Linear Light - Only for recessed installation 80 5 Description RL7035 linear light is mainly designed for recessed installation or continous lighting the light body has simple appearance with
14000 I/O Series Flush Glaze. Fabrication and Installation Instructions
14000 I/O Series Flush Glaze Fabrication and Installation Instructions Last saved on 12/18/2009 Table of Contents GENERAL CONSTRUCTION NOTES...3 EXTRUDED ALUMINUM PARTS...4 ACCESSORIES...5 OVERVIEW...6
ICC INDUSTRIAL CHIMNEY COMPANY INC. ST-JEROME, QUÉBEC, CANADA, J7Y 4B7 TEL: (450) FAX: (450)
ICC INDUSTRIAL CHIMNEY COMPANY INC. ST-JEROME, QUÉBEC, CANADA, J7Y 4B7 TEL: (450) 565-6336 FAX: (450)565-6519 www.icc-rsf.com INSTALLATION AND OPERATION INSTRUCTIONS "Model VIP" CHIMNEY TYPE: FACTORY BUILT
GlasRoc Sheathing Type X
Wall / Fire-Rated Systems 3-5/8" (92 mm) Steel Studs ProRoc Steel Stud System 3-5/8" (92 mm) Steel Track 3-1/2" (89 mm) Glass Fiber or Mineral Wool Insulation GlasRoc Sheathing Type X UL Design U465 Cavity
IMPORTANT WARNINGS AND CAUTIONS!
I N S T R U C T I O N M A N U A L The Christie Vivid Green ceiling mount will suspend your Christie Vivid Green projector in an upright position to compliment conference rooms, classrooms or home theater
A-dec 574L and 575L Dental Lights on a Cabinet or Wall INSTALLATION GUIDE
A-dec 574L and 575L Dental Lights on a Cabinet or Wall INSTALLATION GUIDE A-dec 574L Dental Light Mounted on an A-dec Inspire TM 59 Central Console Before You Begin. Turn off the power to the system before
INSTRUCTIONS. Taurus (BM) Unit Assembly
INSTRUCTIONS Taurus (BM) Unit Assembly Tool Selection QTY Description QTY Description 1 Flat head screw driver 1 Air ratchet 1 Drill with ¼ Bit 1 7/16 deep well socket (for wood base) 1 Drill with 3/16
P /8 Ring Diameter 90. Trim Ring Mounting Holes P /8. 393/16 Ring Diameter. Stud Minimum
PARTS LIST VARIABLE Top Over Head Support Bracket 1 872070 P4000-SMR Over Head Joiner Bracket 1 VARIABLE Bottom Over Head Bracket 1 79741 P4000-SMR 4 Angled Leg 4 100-00230-14 1/4-20 x 31/2 RD. HD. MS.
Sport-Thieme Handball Goal, 3x2 m, Free-Standing or socketed
Assembly instructions Art.-Nr.: 201 0915 203 4502 Sport-Thieme Handball Goal, 3x2 m, Free-Standing or socketed 0218214 2018 Sport-Thieme GmbH D-38367 Grasleben Germany sport-thieme.com info @sport-thieme.com
Ramp Door OEM INSTALL MANUAL
Ramp Door OEM INSTALL MANUAL TABLE OF CONTENTS System and Safety Information 2 Weight Ratings 2 Ramp Door 2 Patio Door 2 Resources Required 2 Installation 3 Notes 5 System and Safety Information The following
INSTALLATION INSTRUCTIONS FOR TEUTONIC ENTRANCE DOOR RECOMMENDATIONS FOR COMMON INSTALLATION OF ENTRANCE DOORS.
INSTALLATION INSTRUCTIONS FOR TEUTONIC ENTRANCE DOOR RECOMMENDATIONS FOR COMMON INSTALLATION OF ENTRANCE DOORS. Installer: DO NOT DISCARD Please leave the Installation Guide with the owner. Please read
Roof Lantern. Installation Guide. Scan to view the installation guide on your mobile or tablet
Roof Lantern Installation Guide Scan to view the installation guide on your mobile or tablet TOOLS REQUIRED Cordless Screwdriver 5mm Hex Bit (Supplied) Soft Mallet Wire Cutters Sealant PACKAGING CONTENTS
GIRTS ON BACK OF BUILDING
GIRTS ON BACK OF BUILDING ALL GIRTS ARE 1 1/2 SQUARE TUBE. GIRT LENGTHS FOR 12, 20, 24, AND 30 WIDE BUILDINGS: ON 12 WIDE BUILDINGS GIRTS ARE 67 3/4 LONG ON 20 WIDE BUILDINGS GIRTS ARE 56 3/4 LONG ON 24
900 SERIES WALL PANELS
CI-DS-01-900 CI-PP-01-900 CI-PJ-01-900 CI-PJ-02-900 CI-PJ-03-900 CI-BS-01-900 CI-BS-02-900 CI-BS-03-900 CI-BS-04-900 CI-BS-05-900 CI-OC-01-900 CI-OC-02-900 CI-IC-01-900 CI-FO-01-900 CI-FO-02-900 CI-FO-03-900