S T E P 1. Tools Needed. Curved Needle Nose Pliers. L Shaped Tool (Supplied w/ kit) Flathead Eyeglasses Screwdriver
|
|
- Amberlynn Bailey
- 6 years ago
- Views:
Transcription
1 Curved Needle Nose Pliers Flathead Eyeglasses Screwdriver L Shaped Tool (Supplied w/ kit) Tools Needed
2 2 Make sure weapon is pointed in a safe direction, unloaded, and on safe.
3 3 Remove lower receiver by pressing take down pin from left to right and slide receiver froward towards muzzle and lift to remove.
4 4 T O O L S N E E D E D 2 3 Use eye glasses screw driver to remove the threaded roll pin from the right side of the Receiver. Use a small flat head screw driver to pry up the plastic OEM selector switch. Remove selector switch from the assembly.
5 5 2 3 Press selector drum from right to left, you will feel the selector drum pop over the safety detent. Remove selector assembly from the left side of the trigger module.
6 6 T O O L S N E E D E D 2 3 Once Selector is removed, place thumb on hammer, squeeze trigger, and ride hammer forward. Use curved needle nose pliers to grab ahold of the front of the hammer spring guide, compress and pivot up and away from hammer and remove.
7 7 T O O L S N E E D E D Use needle nose pliers to remove safety detent and spring.
8 8 Kit Includes: Safety Drum 2x safety lever springs and retention studs 2x selector levers Lever install and removal tool Replacement safety detent spring T O O L S N E E D E D Degree detents 90 Degree detents Installing Handl Defense Safety Selector Determining whether you want a 45 or 90 degree selector options: -45 Degree: Detent index marks are closely positioned together. -90 Degree: Detent index marks appear to be a single point that is visible from the 2 oclock position Desired position will need to face down when installed. It is recommended that a lever to be installed at this point to maintain orientation.
9 9 T O O L S N E E D E D 2 3 Insert small supplied spring and retention stud into the end of the selector cam opposite from the detent notches. Select desired lever and slide dove tail onto the corresponding interface on the selector. Use supplied L shaped tool to depress detent allowing the lever to continue sliding on the dovetail until you hear the retention stud pop into place. Be sure to visually verify detent is engaged by viewing the silver detent thought the hole in the center of the round portion of the lever.
10 0 T O O L S N E E D E D Install safety detent and spring. Use supplied safety detent spring. Do not use OEM detent spring.
11 Apply downward pressure. Insert selector cam into receiver from left to right. Be sure the extended tab of the selector lever is facing to the rear. Apply downward pressure on the safety cam while pressing left to right. You might need to rotate the cam back and forth while doing so. This will allow the cam to fully seat. When fully seated, cam should rotate freely with positive engagement of the detent in the necessary fire positions and main body of cam should be flush with the outside of the receiver on the right side.
12 2 2 3 Insert small supplied spring and retention stud into the end of the selector cam opposite from the detent notches. Select desired lever and slide dove tail onto the corresponding interface on the selector. Use supplied L shaped tool to depress retention stud allowing the lever to continue sliding on the dovetail until you hear the retention stud pop into place. Be sure to visually verify detent is engaged by viewing the silver retention stud through the hole in the center of the round portion of the lever.
13 3 T O O L S N E E D E D 2 3 To re-install the hammer spring, be sure hammer is in the up position. Use curved needle nose pliers to grab the pronged end of the hammer spring guide rod. Insert into large side of the hammer spring support pin. Compress spring and pivot 45 degrees downward allowing U shaped end of the hammer spring guide rod to interface on hammer. Be sure to function test to ensure proper function.
14 4 Your installation is now complete. Be sure to function test weapon and trigger mechanism. Be sure that the desired 45 or 90 degree option has been properly selected. Re-install trigger module onto weapon by reversing steps 2 through 3.
AR-15 Lower Receiver Assembly Instructions
AR-15 Lower Receiver Assembly Instructions Tools There are a few tools that make it easier to put together these kits, but none of them are necessary. Minimum requirements include a hammer and punch to
More informationRepairing Microsoft Wedge Touch Mouse Battery Cover Retaining Clip
Repairing Microsoft Wedge Touch Mouse Battery Cover Retaining Clip Disassembly, repair and reassembly of Wedge Touch mouse when the battery cover will not stay closed. Also is a good guide to repair other
More informationAmerican Morse Equipment
American Morse Equipment Thank you for purchasing an American Morse Porta Paddle-II Kit. We redesigned the original Porta Paddle for ease of assembly & provide all parts finished and ready for assembly,
More informationMS2 Straight Key Kit Assembly Manual
American Morse Equipment MS2 Straight Key Kit Assembly Manual Thank you for purchasing our MS2 Miniature Straight Key Kit! Please take a few minutes to look over these instructions before starting assembly.
More informationFor installation assistance, contact SARGENT at DOORS SHOWN HERE SWING IN FOR ILLUSTRATION PURPOSES ONLY.
SARGENT Installation Instructions for LP8600 x LR8600 & 12-LP8600 x 12-LR8600 Series Low Profile Panic and Fire Exit Devices on Double Egress & Double Doors or LS8600 & 12-LS8600 Low Profile Exit Device
More informationAR-15 Armorer s Essentials Kit. Product # Instructions # Revision: B
AR-15 Armorer s Essentials Kit Product #156111 Instructions #1025769 Revision: B 1 INDEX 3 AR-15 Adjustable Receiver Link 3 Pivot Pin and Roll Pin Installation Tool 4 Mag well Vise Block 7 Upper Vise Block
More informationBasic steps to time the Gammill quilting machine s rotary sewing hook
Basic steps to time the Gammill quilting machine s rotary sewing hook 1.) Turn the machine off and unplug it. 2.) With the needle bar in the raised position, remove the bobbin and bobbin case. 3.) Remove
More informationExterior Door Handle - LH - Unpainted (05-14 All)
Tools Required: Exterior Door Handle - LH - Unpainted (05-14 All) 1) 10mm and 7mm sockets 2) Socket wrench (small size recommended) 3) T30 Torx bit 4) Plastic pry/molding tool (below, A) 5) Thin plastic
More informationTRUE TECHNICAL SERVICE MANUAL - ALL MODELS. DOORS/DRAWERS/LIDS
DOORS/DRAWERS/LIDS 55 56 NOTES DOORS/DRAWERS/LIDS Springs 97 TORSION SPRING REPLACEMENT GDM RADIUS FRONT - SWING DOOR INSTALLATION INSTRUCTIONS Tools Required (2) - 1 8" drift Punch (forged) Needle-Nose
More informationTable of Content. Sayl Disassembly for Recycling
Y Sayl Disassembly for Recycling Table of Content 1. Work Chair Disassembly... 2 2. Side Chair Disassembly...17 3. Work Stool Footring Disassembly... 22 1 Y Sayl Disassembly for Recycling Work Chair Disassembly
More informationHP COLOR LASERJET 3500
HP COLOR LASERJET 3500 TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS HP COLOR LASERJET 3500 TONER CARTRIDGE REMANUFACTURING THE HP 3500 COLOR LASERJET TONER CARTRIDGE By Javier Gonzalez and the Technical
More informationRecommended Equipment and Tools
Recommended Equipment and Tools [1] Philips Screwdriver [2] Flat Blade Screwdriver [3] 1/8 Hex Driver [4] Needle-nosed Pliers [5] X-acto Knife [6] Soft Foam Pad (or equivalent) Equipment and Tools PAGE
More informationM14 MODULAR CHASSIS SYSTEM (MOD 1) INSTRUCTION MANUAL. West Springfield, MA Phone: (866) FAX: (413)
M14 MODULAR CHASSIS SYSTEM (MOD 1) INSTRUCTION MANUAL Troy Industries, Inc. WWW.TROYIND.COM West Springfield, MA 01089 Phone: (866) 788-6412 FAX: (413) 383-0339 Thank You M14/M1A MODULAR CHASSIS SYSTEM
More informationM14 MODULAR CHASSIS SYSTEM (MOD 1) INSTRUCTION MANUAL. West Springfield, MA Phone: (866) FAX: (413)
M14 MODULAR CHASSIS SYSTEM (MOD 1) INSTRUCTION MANUAL Troy Industries, Inc. WWW.TROYIND.COM West Springfield, MA 01089 Phone: (866) 788-6412 FAX: (413) 383-0339 Thank You M14/M1A MODULAR CHASSIS SYSTEM
More informationM*CARBO Winchester Model 70 Trigger Spring Kit Download or Print Instructions Contact: Page 1
Download or Print Instructions Contact: help@mcarbo.com Page 1 Step 1: Clear your Firearm - Remove the magazine, check the chamber, bolt face and magazine well. Step 2: Gather Parts and Tools Needed Step
More informationReplacing the Reciprocator on an SWF Multi-head.
Replacing the Reciprocator on an SWF Multi-head. Follow the instructions below to replace the reciprocator in the SWF multi-head machines. The tools required are found in the tool kit that came with the
More informationPowerbook G3 Lombard (1999) USB Repair Manual
Powerbook G3 Lombard (1999) USB Repair Manual Copyright 2003 Powerbookmedic.com. All rights reserved. Any portion of this manual may not be copied, reproduced, or distributed without the express written
More informationMMD Convertible Styling Bar Customer Installation Guide
MMD Convertible Styling Bar Customer Installation Guide TOOLS REQUIRED/RECOMMENDED: Electric Drill 1 Forstner Bit (Hole Saw) 1 3/8 Hole Saw (manual calls for 1 ¾ ) 1/8, 3/8 & ¾ Drill Bits Rivet Gun Trim
More information1. Turn off or disconnect power to unit (machine). 2. Push IN the release bar on the quick change base plate. Locking latch will pivot downward.
Figure 1 Miniature Quick Change Applicators, of the end feed type, are designed to crimp end feed strip terminals to prestripped wires. Each applicator is set up to accept the strip form of certain specific
More information100mm (3in) Slide Stop Cut to 6mm (1/4in) Sections. Quantity: mm (10in) Skewers Quanity: 10. Material to Lift. Material for Blades.
Wind Lift Page 1 The Activity This guide will take you through the process of creating a wind powered lift. You ll start by creating the stand. The lift mechanism, hub and blades are then added. Before
More information3.2.3 Rear Door Window and Quarter Window Carrier Assembly
Tighten all bolts. Tighten bolts marked -1- and -2- in specified sequence. Tightening torque: 8 Nm Remaining bolts can be tightened in any sequence. Insert door window -3- through window recess without
More informationESRA III. Expressive System for Robotic Animation
ESRA III Expressive System for Robotic Animation 1 ESRA III Kit Contents 1 Hitec Servos 8 Upper Eye Support 2 Dagu (New as of 7/12) 9 Lower Eye Support 3 Eye Balls 10 Main Support 4 Flat Servo Plate 11
More informationSignal Mirror Installation Instructions
Signal Mirror Installation Instructions 2006 2007 Honda Ridgeline THE safety accessory of the 21 st Century. P/N 210 0142 0 Rev. A (9/5/07), BTV 2007 Muth Company, LLC Professional Installation Recommended:
More information*D-1030* 1 PARTS CHECK 8 REVERSING INSTRUCTIONS F-XX-C & XX-C D Customer Service. Installation Instructions. Exit Devices
*D-1030* D-1030 F-XX-C & XX-C Exit Devices Installation Instructions 8 REVERSING INSTRUCTIONS TO REVERSE THE HANDING OF A (F)XX-C DEVICE NOTE: TO REVERSE TRIM, REFER TO SEPARATE INSTALLATION SHEETS. 1
More information7878 K940. Checkpoint Antenna. Kit Instructions. Issue B
7878 K940 Checkpoint Antenna Kit Instructions Issue B Revision Record Issue Date Remarks A July 7, 2009 First issue B Nov2013 Revised the Checkpoint installation procedures for 7878 and 7874 scanners Added
More informationInstallation Instructions for FC2 & FC15 Forward Controls for the Super Magna
Installation Instructions for FC2 & FC15 Forward Controls for the Super Magna It is highly recommended that you use a thread lock compound such as Loctite brand on all threads to keep them from vibrating
More informationBUILDING A GHOST GLOCK. Prepper Mike
BUILDING A GHOST GLOCK Prepper Mike WHAT IS A GHOST GLOCK? Ghost guns are guns that don t need to be registered Ghost guns are built by the owner based on not more than 80% complete lowers Ghost guns are
More informationMANUAL CARTON STAPLER MODEL: H-1025 MANUAL
MANUAL CARTON STAPLER MODEL: H-1025 MANUAL WARNING Before operating this stapler familiarize yourself with the safety warnings and instructions in this manual. Keep these instructions with the stapler
More informationBearing Overhaul Instructions for: Tallboy (.1) 2009
Bearing Overhaul Instructions for: Tallboy (.1) 2009 Tools Needed: 7900 Removal Tool 7902 Removal Tool 7900/7902/6902 Press Tool Grease Gun (included with frame) (2) ll/16" or adjustable wrenches 9/16"
More informationReplacing the Reciprocator on the SWF Compact Series Machine (601C and 1201C)
Follow the instructions below to replace the reciprocator in the SWF Compact series machines. The tools required can be found in the tool kit that came with the machine. Preparation 1. First, place the
More informationIMPORTANT! Recommended Tools. 7/16 Deep socket Phillips screwdriver
IMPORTANT! Read all instructions carefully before commencing any work. Always wear proper safety equipment. Some installation steps will require two or more installers. Recommended Tools Ratchet 10-mm
More informationPRO 400 M401 MFP M425 CF-280A/X TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS
HP PRO 400 M401 MFP M425 CF-280A/X TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS HP CF-280A/X TONER CARTRIDGE REMANUFACTURING THE HP LASERJET PRO 400 M401/MFP M425 (CF-280A/X) TONER CARTRIDGE By Mike Josiah
More informationThis instruction manual is an in-depth look and explanation of how to assemble and install the Murphy Bed properly and efficiently.
This instruction manual is an in-depth look and explanation of how to assemble and install the Murphy Bed properly and efficiently. Don t be put off by the size of the instruction manual as the large diagrams
More informationHP M506/MFP M527 CF-287A/X
HP M506/MFP M527 CF-287A/X TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS HP CF-287A/X TONER CARTRIDGE REMANUFACTURING THE HP LASERJET ENTERPRISE M506/MFP M527 CF-287A/X TONER CARTRIDGE By Mike Josiah and
More informationRobodyssey ESRA III. Expressive System for Robotic Animation
Robodyssey ESRA III Expressive System for Robotic Animation Assembly and Operation Instructions Version 1.0 Robodyssey Systems, LLC. Phone/Fax: 609-585-8535 20 Quimby Avenue Web: www.robodyssey.com Trenton,
More informationVolkswagen Window Regulator Repair
The tools you will need to complete the repair will be a T20 Torx screwdriver and a Flat Screwdriver additionally, you could also use a pair of pliers to remove the plastic plug holding the wire nearest
More informationRIVAL CALIBURN ASSEMBLY
RIVAL CALIBURN ASSEMBLY 08/02/18 The RIVAL Caliburn is a Mag-Fed Pump-Action Homemade Nerf Blaster design released as a Public Domain license file set by Captain Slug (http://www.captainslug.com). You
More informationRepair Instructions. Replacing a La Z Time Mechanism Side Subassembly. Remove the Back(s): Remove the Mechanism Assembly: CAUTION.
Replacing a La Z Time Mechanism Side Subassembly Tools Required: Slotted Screwdriver Power Driver 8" Driver Extension Ruler Note: Extension springs are not typically used on non-chaise standard width styles,
More informationKIT. Assembly Instructions. HayDay, LLC
KIT Assembly Instructions HayDay, LLC 1-800-732-1654 www.stablegrazer.com Read completely through the assembly instructions before starting assembly. The Stable Grazer Kit comes in two boxes. Remove all
More informationSTAGE PAGE. 6 The left front door interior The right front wheel The right front seat back The right front wheel 37
Pack 2 STAGE PAGE 6 The left front door interior 25 7 The right front wheel 29 8 The right front seat back 33 9 The right front wheel 37 10 The right front door 41 11 The right front door window 45 12
More informationIntroduction: The T30069 Center Punch Tool installs BAND-IT 3/8" and 5/8", 201 Stainless Steel and Galvanized Carbon Steel clamps.
Instruction Manual Introduction: The Center Punch Tool installs BAND-IT 3/8" and 5/8", 201 Stainless Steel and Galvanized Carbon Steel clamps. Table of Contents: 1. Introduction & Safety Practices 2. Operating
More informationPLEASE READ THE ENTIRE BULLETIN BEFORE BEGINNING THE PROCEDURE
Bulletin # 205 System 4 Board Replacement Page 1 of 5 Summary Products Affected Key Word Tags Tools/Equipment (If Required) Parts/Materials (If Required) Related Media Replacing the System 4 control board
More informationProctor Silex 2-Slice Extra Wide Slot Toaster Teardown
Proctor Silex 2-Slice Extra Wide Slot Toaster Teardown Taking apart the Proctor Silex 2-Slice Toaster is order to access it's circuit board for maintenance. Written By: Cory ifixit CC BY-NC-SA www.ifixit.com
More informationRTA-3520 DIMENSIONS MAXIMUM WEIGHT CAPACITIES. Product Size: 47.5"W x 23"D x 30"H
MODEL RTA - 3520 Thanks for purchasing one of our products. Please read carefully the assembly instructions before the installation. Please save this manual for future reference. Complete video assembly
More informationIntroduction: The T30069 Center Punch Tool installs BAND-IT 3/8" and 5/8", 201 Stainless Steel and Galvanized Carbon Steel clamps.
Instruction Manual Introduction: The Center Punch Tool installs BAND-IT 3/8" and 5/8", 201 Stainless Steel and Galvanized Carbon Steel clamps. Table of Contents: 1. Introduction & Safety Practices 2. Operating
More informationSTEINBERGER TRANSTREM (TYPE 2) TECHNICAL DOCUMENT
STEINBERGER TRANSTREM (TYPE 2) TECHNICAL DOCUMENT These instructions apply to newer style TransTrems only (non-threaded ball type or modified threaded ball type). For purposes of discussion, these TransTrems
More informationPage 1 of 12 DZ /02/15
Page 1 of 12 Dee Zee Running Board Installation Instructions Congratulations on your purchase of a quality Dee Zee product. Dee Zee is recognized as having the highest quality running boards and accessories
More informationRazr Adapter Retrofit Project by Craig Hoy, Edmonton, AB, Canada
Razr Adapter Retrofit Project by Craig Hoy, Edmonton, AB, Canada The following is a description of the process that I have used to modify the console eject box for e38, e39, e46 and x5 s, part number 84-21-6-933-415.
More informationINSTALLATION INSTRUCTIONS GRILLE GUARD RAM 1500 PART # 5058/5058-2
INSTALLATION INSTRUCTIONS GRILLE GUARD PART # 5058/5058-2 PARTS LIST: Qty Description Qty Description 1 Grille Guard 8 12-1.75mm x 35mm Hex Bolts 2 Upper Frame Mounting s (for trucks without tow hooks
More informationINSTALLATION INSTRUCTIONS DODGE RAM 2 & 4WD 1500 PART # P5058
INSTALLATION INSTRUCTIONS 2009-13 DODGE RAM 2 & 4WD 1500 PART # P5058 PARTS LIST: Qty Description Qty Description 1 Grille Guard 12 12-1.75mm Hex Nuts 2 Upper Frame Mounting s (for trucks without tow hooks
More information5X Racing Mazda Miata Shifter Rebuild Kit Installation Instructions
5X Racing 1999-2005 Mazda Miata Shifter Rebuild Kit Installation Instructions Thank you for purchasing our Miata shifter rebuild kit for the 1999-2005 Mazda Miata! These instructions will guide you on
More informationApplications: Section 1: Getting Started Tools Needed: BEFORE
Installation of KBD Body Kits Porsche GT 3 Look/Style 2 Piece Polyurethane Front Bumper & Lip Applications: Porsche 996: 1999-2001 Porsche Boxster 986: 1997-2004 Page 1 Tools Needed: Philips Head Screwdriver
More informationINVENT3D Printer Kit Disassembly Instructions
INVENT3D Printer Kit Disassembly Instructions Version 6 AST2 10/26/16 1 I. General Disassembly Instructions Use the case layer drawings to ensure that components are stored in the appropriate location
More information40 & 50 Foot PS-1 Box Car Assembly Instructions
40 & 50 Foot PS-1 Box Car Instructions Push the #2100 coupler/stirrup assembly onto the ends of the metal floor. Slide them into the slots and slightly lift the ends (wings), then press firmly on the front
More information4. Z-axis assembly. 4. Z-axis assembly. Written By: Josef Prusa manual.prusa3d.com Page 1 of 18
4. Z-axis assembly Written By: Josef Prusa 2017 manual.prusa3d.com Page 1 of 18 Step 1 Get the necessary tools 13/17mm spanners 3.6mm flathead screwdriver Needle-nose pliers 2.5 and 1.5mm Allen key Step
More information2015 GMC Yukon. Upper Class Grille Insert
Upper Class Grille Insert TOOLS REQUIRED: Flat Head Screwdriver Long Flat Head Screwdriver Phillips Screwdriver 7mm Socket 10mm Socket Ratchet & Extensions 3/16 Drill Bit Power Drill Cutting Wheel or Saw
More informationThe Bowflex Revolution XP Home Gym Assembly Instructions. P/N: Rev ( /0 )
P/N: 001-7057 Rev ( /0 ) The Bowflex Revolution XP Home Gym Assembly Instructions 2 Table of Contents Before You Start... 2 Tools You Will Need / Hardware Contents... 3 Box Contents... 6 Assembling Your
More informationRingblaster Mark IV Maintenance Guide. Version 1.5
Ringblaster Mark IV Maintenance Guide Version 1.5 WARNING Winchester Industrial Equipment and Loads must be properly stored, handled and maintained for safe and proper function. Mishandling or failure
More informationINSTRUCTION BOOKLET #34. For Wallbed models: KING SIZE SIERRA WITH STORAGE HEADBOARD
For Wallbed models: KING SIZE SIERRA WITH STORAGE HEADBOARD INSTRUCTION BOOKLET #34 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION
More information5X Racing Miata Radio Delete Plate Installation Instructions
5X Racing 99-05 Miata Radio Delete Plate Installation Instructions Thank you for purchasing our unique, aluminum race inspired radio delete plate for your 1999-2005 Mazda Miata! These instructions will
More informationTRUE TECHNICAL SERVICE MANUAL - ALL MODELS. DOORS/DRAWERS/LIDS
DOORS/DRAWERS/LIDS 55 56 NOTES DOORS/DRAWERS/LIDS Swing s 73 74 NOTES INSTALLATION OF A GDM-SWING DOOR Phillips Head Screwdriver (2) - 1/8" Drift Punches (forged) Top Bracket NOTE: It may be necessary
More informationCALIBURN ASSEMBLY INSTRUCTIONS
CALIBURN ASSEMBLY INSTRUCTIONS The Caliburn is a Mag-Fed Pump-Action Homemade Nerf Blaster design released as a Public Domain license file set by Captain Slug (http://www.captainslug.com). You are welcome
More informationTriplex Instructions for Packing and Unpacking
2-8-8-2 Triplex Instructions for Packing and Unpacking It is recommended that you review all these instructions before removing the engine or tender from the poly foam container. www.mthtrains.com Table
More informationInstallation Instructions 8115F 8115SF
TM Installation Instructions 85F 85SF Single Control Centerset Lavatory Faucet with Speed Connect Drain Congratulations on purchasing your American Standard faucet with the Speed Connect Drain, a feature
More informationLEFT-SIDE CARTR. LATCH REPLACEMENT
Service Edge Page 5 long screw A. TOP COVER: 3 short screws, 1 long screw B. LEFT COVER: 4 tabs, 2 screws SCREW SCREW LEFT-SIDE CARTR. LATCH REPLACEMENT CLJ 3000, 3600, 3800, CP3505 This printer series
More informationReferencing 0,0 position
Page 1 of 11 TITLE: SABRE X-Axis Lead Screw Replacement Procedure Gerber FastFact #: 2013 Supplied by: Gerber Hardware Support Last Modified: March 1, 2011 Summary: The following procedure explains how
More informationSHUR-LOK CORPORATION TECHNICAL SALES BULLETIN
Page 1 of 11 1.0 INTRODUCTION: 1.1 This Technical Sales Bulletin describes installation procedure of SL850 Blind-Threaded and SL854 Thru-Threaded Pull-up type inserts. These procedures use the SLPGA850
More informationXEROX PHASER 3600 TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS
XEROX PHASER 3600 TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS XEROX PHASER 3600 TONER CARTRIDGE REMANUFACTURING THE XEROX PHASER 3600 TONER CARTRIDGE By Mike Josiah and the Technical Staff at UniNet The
More informationSUPER PRO GUN & SUPER PRO GUN II
MAGNUM VENUS PRODUCTS Maintenance & Repair Manual Part No. M6707-1-1 Revision 04.14.01 Maintenance & Repair Corporate HQ & Mfg. Phone: (727) 573-2955 Fax: (727) 571-3636 Email: info@magind.com Web: www.magind.com
More informationService Bulletin
Service Bulletin 18-026 April 24, 2018 Version 5 Safety Recall: Left (Driver Side) Second Row Seat Recliner Does Not Lock Supersedes 18-026, dated April 7, 2018 to revise the information highlighted in
More informationJenny Legs Assembly Instructions
Jenny Legs Assembly Instructions R EXTENDED PHILLIPS BIT MM ALLEN WRENCH 6MM HEX DRIVE /" 007 Steelcase Inc. Grand Rapids, MI 90 U.S.A. Printed in U.S.A. Page of 6 88000 Rev F Jenny Club Instructions:
More informationINSTALLATION INSTRUCTIONS
TOOLS REQUIRED: Level Square Phillips Screw Driver Slot Screw Driver Pliers Clamp PARTS PROVIDED: Frame Installations Screws. 4 per door. (#8 x 1-3/4 ) Sex Bolt. 4 per frame joint. Torque Lever 2 Shelf
More informationMini Cooper Lock Actuator
2001-2006 Mini Cooper Lock Actuator Replacement This guide is on how to remove the lock actuator from the cars door. Written By: Jem ifixit CC BY-NC-SA www.ifixit.com Page 1 of 13 INTRODUCTION In order
More informationQB78 CO 2 Pellet Rifle
QB78 CO 2 Pellet Rifle Maintenance Instructions Text and photos by George Fox Lang The Chinese QB78 pellet rifle is one of the nicest and most popular CO 2 rifles ever produced. Here are the long-wanted
More informationDroplit v2 Frame Assembly
SeeMeCNC Guides Droplit v2 Frame Assembly Droplit v2 Frame Assembly Written By: JJ Johnson 2017 seemecnc.dozuki.com Page 1 of 22 Step 1 Droplit v2 Frame Assembly Locate the Projector Plate, Projector Joining
More informationTop Innovations, Inc. Innovative Products to Make Your Life Easier. Model SP-402 Owner s Manual
Top Innovations, Inc. Innovative Products to Make Your Life Easier Model SP-402 Owner s Manual THIS IS NOT A TOY! Adult supervision recommended Item contains sharp functional points and small parts Machine
More informationInstallation And Care Instructions. Vertical Honeycomb Shades
Installation And Care Instructions Vertical Honeycomb Shades Rev 5/2013 Table Of Contents Getting Started... 3 Parts Overview... 4 Materials Required... 5 Tools Required... 6 Outside Mount Installation...
More informationCALIBURN ASSEMBLY INSTRUCTIONS
CALIBURN ASSEMBLY INSTRUCTIONS The Caliburn is a Mag-Fed Pump-Action Homemade Nerf Blaster design released as a Public Domain license file set by Captain Slug (http://www.captainslug.com). You are welcome
More informationFig Remove chain cover plate bolts. Fig Remove hammer member. Fig Loosen set screws at base of 12-tooth sprocket.
Fig. 17.2. Remove chain cover plate bolts. Fig. 17.1. Remove hammer member. Fig. 17.3. Remove chain cover plate. Fig. 17.4. Loosen set screws at base of 12-tooth sprocket. Page 61 Fig. 17.5. Remove socket
More informationHarmony Remote Repair
Harmony Remote Repair harmonyremoterepair.com How to install your new Harmony One Front Cover/Touch Screen Important! Before you begin working on your Harmony One, you must discharge any static electricity
More informationInstallation for Full Size Polaris Ranger Crew Doors
Installation for Full Size Polaris Ranger Crew Doors Order of Installation: Heater Doors Wiper on to Windshield Windshield Top & Back Panel Note: Most of the steps in these instructions need to be repeated
More informationPAK Drum Roll Top Assembly Instructions. Note: 2 people will be required to assemble roll top
PAK901 4 Drum Roll Top Assembly Instructions Note: 2 people will be required to assemble roll top PLEASE READ ASSEMBLY INSTRUCTIONS CARFULLY Tools required: 5/8 Socket & Ratchet 9/16 Deep Well Socket &
More informationD3976 RECESSED EXIT INSTALLATION INSTRUCTIONS
PACKAGE CONTENTS PRODUCT MUST BE INSTALLED ACCORDING TO ALL APPLICABLE BUILDING AND LIFE SAFETY CODES TEMPLATE INSTALLATION INSTRUCTIONS STRIKE HAND TOOL 5/32 HEX KEY ROD END CAPS EXIT DEVICE CRANK ARM
More informationDIY S2000 Door Card Removal
DIY S2000 Door Card Removal This Do-It-Yourself guide is intended to guide you through removing the door cards from your S2000. Tools Required: Phillips Head Screwdriver Trim tools (pry tool and a trim
More informationModule One: Non Powered Hand Tools
Module One: Non Powered Hand Tools What is included in this module Why are we learning this? Safety rules Right tool for the right job Identity of Tools Hands on time Quiz Why are we here? Basic knowledge
More informationMac mini Model A1176 SSD Installation
Mac mini Model A1176 SSD Installation Installing an SSD in the Mac Mini A1176 Written By: Dozuki System 2017 guides.crucial.com Page 1 of 13 INTRODUCTION Upgrade your hard drive for more storage capacity.
More informationHow to: Disassemble and Reassemble the M1 Garand.
Yugo M-48 M1 Garand Russian Mosin Nagant Swiss Schmidt Rubin Swedish Mauser German Mauser 98k Finnish Nagant Nagant Carbines How to: Disassemble and Reassemble the M1 Garand. So, you just purchased a surplus
More informationP.O. Box 8400 Green Bay, WI (920)
P.O. Box 8400 Green Bay, WI 54308-8400 (920) 468-2165 Change Notice No. 112 Implemented By: KI-Pembroke Notification By: Scott Vissers Date: 03/15/10 Component Product Title: Series XXI Lateral Filing
More informationREMOVAL/INSTALL INSTRUCTIONS: REPLACEMENT RADIO BUTTONS
REMOVAL/INSTALL OF RADIO BUTTONS (Part# 76824) GM Vehicles 2003-2007 General Tech Tips: Work in a location that is clean & static-free (static discharge has the potential to permanently damage electrical
More informationASSEMBLING YOUR L&L EASY-FIRE KILN
TABLE OF CONTENTS TOOLS NEED FOR THE JOB............ 1 UNPACKING........................... 2 Inspect for visible damage.......................... 2 Remove Top from Carton........................... 2
More informationINSPECTION AND CORRECTION OF BELLHOUSING TO CRANKSHAFT ALIGNMENT
INSPECTION AND CORRECTION OF BELLHOUSING TO CRANKSHAFT ALIGNMENT BACKGROUND Proper alignment of the transmission input shaft to the crankshaft centerline is required in order to achieve the best results
More informationInstallation Instructions for Cirrus Suspension Downlight with Power - End Feed. Section One: 4" Flush Canopy Version
Doc # 0-CSP-E_0 W. Fullerton Chicago, IL 606 Ph:.0. Fax:..6 www.pureedgelighting.com info@pureedgelighting.com 06 PureEdge Lighting. All Rights Reserved. Installation Instructions for Cirrus Suspension
More informationELECRAFT KXPD1 PLUG-IN KEYER PADDLE
Introduction ELECRAFT KXPD1 PLUG-IN KEYER PADDLE Assembly and Operating Instructions Revision B, July 27, 2011. Copyright 2011, Elecraft; All Rights Reserved The KXPD1 is a unique plug-in keyer paddle
More informationHDL(M)6 Nut/Screw Assembly
HDL(M)6 Nut/Screw Assembly Remove, repair, and reassemble the nut and screw assembly in your HDL series double lock vise. In these instructions when we refer to the front of the vise or nut/screw assembly,
More informationAdjusting, Changing and Maintaining The Latches and Catches on Your Airstream
Adjusting, Changing and Maintaining The Latches and Catches on Your Airstream Hinges,Latches and Catches in your Airstream Bumps, pulling, gravity and time can have an affect on hinges and latches. Adjustments
More informationES# ECS MKV R32 Dead Pedal Kit Installation Instructions
ECS MKV R32 Dead Pedal Kit ES#261054 Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles as well as the personal safety of those performing the repairs.
More informationPRINTER REPAIR ARTICLE HP LJ 4345/M4345 Swing Plate Replacement
a1 output bin a2 DUPLEXER a4 FORMATTER COVER a5 FORMATTER a3 fuser entr. guide PRINTER REPAIR ARTICLE HP LJ 4345/M4345 Swing Plate Replacement Grinding noise near the fuser means it is time to replace
More informationWPS crew Doors Installation instructions
WPS-132-133 crew Doors Installation instructions ORDER OF INSTALLATION FOR A COMPLETE ENCLOSURE OF A CREW WPS (Weather Protection System) IS AS FOLLOWS: 1. Heater 2. Rear Thresholds - Right Hand & Left
More informationSentinel Series Cigar Humidor End Tables
Sentinel Series Cigar Humidor End Tables Assembly Instructions Models: Sentinel 500, 1000 and 1500 Style: Traditional SENTINEL ASSEMBLY INSTRUCTIONS Congratulations! You have purchased a superior cigar
More informationOD1505 MAINTENANCE OF THE M249 MACHINEGUN
SUBCOURSE OD1505 EDITION 7 MAINTENANCE OF THE M249 MACHINEGUN US ARMY TANK TURRET REPAIRER CORRESPONDENCE COURSE MOS/SKILL LEVEL: 45K30 MAINTENANCE OF THE M249 MACHINEGUN SUBCOURSE NO. OD1505 US Army
More information