Mounting Kit for HP N-class Servers AR8014A

Size: px

Start display at page:

Download "Mounting Kit for HP N-class Servers AR8014A"

Brendan Parsons
5 years ago
Views:

1 Mounting Kit for HP N-class Servers AR8014A This kit is used to mount an HP N-class or rp7400 server in a NetShelter SX or VX enclosure. HP compatibility bracket (2) SX extender brackets (4) M6 12 Torx screw (32) M6 caged nut (24) Tools required Caged nut tool Torx T30/#2 Phillips wrench Drill How to install and remove caged nuts To install a caged nut: Warning Install the caged nut horizontally. Do not install the caged nut vertically with the sides of the caged nut engaging the top and bottom of the square hole. 1. Insert the caged nut into the square hole by hooking one side of the caged nut assembly through the far side of the hole. 2. Place the caged nut tool (provided) on the other side of the caged nut and pull to snap it into position. To remove a caged nut: 1. Remove any attached screw. 2. Grasp the caged nut and squeeze the sides to release it from the square hole.

2 Installation for a NetShelter SX enclosure 1. Install two caged nuts in the side-facing holes of each of the four mounting flanges. 2. Install an SX bracket extender on each of the four mounting flanges using eight M6 x 12 Torx screws and the caged nuts installed in step 1. ns0947a ns0945a 2 Mounting Kit for HP N-class Servers AR8014A

3 3. Install 16 caged nuts on the SX bracket extenders, four caged nuts per bracket, three U-spaces apart. (The top and the bottom caged nut should be in the center hole of a U- space.) 4. Install the HP compatibility bracket, using eight M6 x 12 Torx screws (provided). ns0953a ns0948a 5. Install the HP rail onto the bracket, using four M6 screws (provided with server). 6. Repeat steps 4 5 for the other side of the enclosure and continue installation as specified in the HP manual. Mounting Kit for HP N-class Servers AR8014A 3

4 Installation for a NetShelter VX enclosure 1. Install eight caged nuts on the sides of the front and rear mounting flanges 5 U-spaces apart. (The top and the bottom caged nut should be in the center hole of a U-space.) 5U ns0300a 2. Align the holes on the bracket with the caged nuts, but do not secure the bracket in place. 3. Mark the bracket slot positions on each flange and remove the bracket. 4. Drill holes in the mounting flanges at the marked locations using a drill bit with a diameter of 1/2-inch (13 mm) or larger. ns0302a ns0301a 4 Mounting Kit for HP N-class Servers AR8014A

5 5. Install the bracket, using eight M6 x 12 Torx screws (provided). ns0303a 6. Install the HP rail onto the bracket, using four M6 screws (provided with server). 7. Repeat steps 1 6 for the other side and continue installation as specified in the HP manual. Mounting Kit for HP N-class Servers AR8014A 5

8 APC Worldwide Customer Support Customer support for this or any other APC product is available at no charge in any of the following ways: Visit the APC Web site to access documents in the APC Knowledge Base and to submit customer support requests. (Corporate Headquarters) Connect to localized APC Web sites for specific countries, each of which provides customer support information. Global support searching APC Knowledge Base and using e-support. Contact an APC Customer Support center by telephone or . Regional centers: Direct InfraStruXure Customer Support Line APC headquarters U.S., Canada Latin America Europe, Middle East, Africa (1)(877) (toll free) (1)(800) (toll free) (1)(401) (USA) (353)(91) (Ireland) Japan (0) Australia, New Zealand, South Pacific area (61) (2) (Australia) Local, country-specific centers: go to for contact information. Contact the APC representative or other distributor from whom you purchased your APC product for information on how to obtain local customer support. Entire contents 2005 American Power Conversion. All rights reserved. Reproduction in whole or in part without permission is prohibited. APC, the APC logo, InfraStruXure, and NetShelter are trademarks of American Power Conversion Corporation and may be registered in some jurisdictions. All other trademarks, product names, and corporate names are the property of their respective owners and are used for informational purposes only. * B-001* B /2005

NetShelter Recessed Rail Kit AR8010BLK

NetShelter Recessed Rail Kit AR8010BLK Inventory M6 screw (24) M6 caged nut (24) 6U 15U Horizontal brace (4) Horizontal brace (2); when using baying brackets 6U and 15U vertical mounting rail (4 each)