Installation Instructions

Transcription

1 TS SERIES Traditional Square Accessories Installation Instructions " TOWEL BAR.0 " TOWEL BAR.0.90 DOUBLE ROBE HOOK.0.0 " HANDLE. " HANDLE.0 Thank you for selecting American-Standard...the benchmark To ensure that your installation proceeds smoothly--please read instructions carefully before you begin. M9 REV.. Recommended Tools 0' Tape Measure Electric Drill Level INSTALLATION OF MOUNTING BRACKETS FOR ALL WALL MOUNTED ACCESSORIES The WALL MOUNTED ACCESSORIES work best if secured to a wall stud or cross brace within the wall, using the SCREWS () supplied. If the ACCEASAORY is to be installed on a tile or plaster wall the ANCHORS () and SCREWS () should be used. Determine desired height and location (optional) and mark a center line. Make sure the centerline is level. Using the MOUNTING BRACKET () as a template mark the two spots for the mounting holes. If MOUNTING BRACKET () is secured to a stud or cross brace drill small pilot holes for SCREWS (). For installations on tiled walls or drywall, use TILE ANCHORS () and SCREWS () for securing MOUNTING BRACKET () to wall. Drill two /" diameter holes a minimum of -/" deep. Insert the two TILE ANCHORS () flush with face of finished wall. Place MOUNTING BRACKET () over TILE ANCHORS () and insert SCREWS () provided with a flat blade screwdriver. See illustration below. Secure MOUNTING BRACKET () to wall with SCREWS () Regular Screwdriver Phillips Screwdriver mm Hex wrench CARE INSTRUCTIONS: DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH. DO NOT: CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH WITH A COARSE SURFACE. DRILL PILOT HOLE FOR WOOD SCREW () OR /" DIA. HOLE FOR ANCHOR () C L /" (9mm) /" (9mm)

2 and ROBE HOOK INSTALLATION Refer to Step for installation of MOUNTING BRACKETS (). Align accessory and place ACCESSORY ESCUTCHEON () onto MOUNTING BRACKET (). Secure accessory with () using a mm HEX WRENCH (). INSTALL Refer to Step for installation of MOUNTING BRACKETS (). NOTE: The center line distance between the two MOUNTING BRACKETS is -/" (mm). Make sure the two MOUNTING BRACKETS () are level. Install the ACCESSORY ESCUTCHEONS () on the MOUNTING BRACKETS (). Make sure the ACCESSORY ESCUTCHEONS () with holes for the horizontal shaft are facing inward. Secure ACCESSORY ESCUTCHEONS () with () using a mm HEX WRENCH (). Install the PAPER HOLDER SHAFT () into the mounted ACCESSORY ESCUTCHEONS (). " (mm) M9 REV..

3 " and " TOWEL BAR INSTALLATION Refer to Step for installation of MOUNTING BRACKETS (). NOTE: The center line distance between the two MOUNTING BRACKETS is " (.mm) or " (09.mm). Make sure the two MOUNTING BRACKETS () are level. Install the ACCESSORY ESCUTCHEONS () on the MOUNTING BRACKETS (). Secure ACCESSORY ESCUTCHEONS () with () using a mm HEX WRENCH (). " (.mm) " (09.mm) " HANDLE INSTALLATION Note: Professional installation is required for this product. The warranty does not cover damage to the shower door due to improper installation. Determine the desired height and location and mark a horzontial centerline. Make sure the centerline is level. Drill two /" (mm) diameter mounting holes through the shower door " (09.mm) apart. Insert BOLTS (), GASKETS () and INSERTS () on the inside of the shower door. On the outside of the shower door, install SQUARE GASKETS (a), MOUNTING BRACKETS () and HEX NUTS (). Tighten HEX NUTS () but do not over tighten. Install HANDLE () onto MOUNTING BRACKETS (). Secure the HANDLE () with S () using a mm HEX WRENCH (). /" - /" (.mm - 9.mm) C/L " (09.mm) () /" (mm) DIA. MOUNTING HOLES a a M9 REV..

4 " HANDLE INSTALLATION Note: Professional installation is required for this product. The warranty does not cover damage to the shower door due to improper installation. Determine the desired height and location and mark a vertical centerline. Make sure the centerline is level. Drill two /" (mm) diameter mounting holes through the shower door " (.mm) apart. Insert BOLTS (), GASKETS (), INSERTS () and MOUNTING BRACKETS () on the inside of the shower door. On the outside of the shower door, install GASKETS (), MOUNTING BRACKETS () and HEX NUTS (). Tighten HEX NUTS () but do not over tighten. Install HANDLE () onto MOUNTING BRACKETS (). Secure the HANDLE () with S () using a mm HEX WRENCH (). " (.mm) " (.mm) C/L () /" (mm) DIA. MOUNTING HOLES /" - /" (.mm - 9.mm) M9 REV..

5 DOUBLE ROBE HOOK.0 M9-000A M9-000A M9-000A M9-000A M9-000A.0 TS SERIES Traditional Square Bath Accessories " TOWEL BAR " TOWEL BAR DOUBLE ROBE HOOK " HANDLE " HANDLE MODEL NUMBERS M9-000A.90 M9-YYYOA " HANDLE. M9-000A " TOWEL BAR.0 " HANDLE.0 M9-000A M9-000A M9-000A Replace the "YYY" with appropriate finish code CHROME OIL RUBBED BRONZE SATIN NICKEL " TOWEL BAR M9-000A M9-000A M9-000A HOT LINE FOR HELP For toll-free information and answers to your questions, call: Weekdays :00 a.m. to :00 p.m. EST IN MEXICO IN CANADA (TORONTO ) Weekdays :00 a.m. to :00 p.m. EST Product names listed herein are trademarks of American Standard Inc. AS America, Inc. 0 M9 REV..