Installation Instructions
|
|
- Morris Casey
- 6 years ago
- Views:
Transcription
1 MOUNT TUB SYSTEMS HAMPTON TRIM KIT T Installation Instructions T T T T Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. Trim Kits 4mm 5mm Certified to comply with ANSI A U.S. Patent No. D403,750 M968655A T mm 5mm LEVER T mm LEVER T mm 1 INSTALLATION Complete FINISHED before trim installation. Turn off the water supplies. Remove the GUARDS from the BODIES. Remove the GUARD and 1/4" PLUG from the SHANK. 5mm The SHANK height should be 1" to 2" above the FINISHED. Cut the SHANK if necessary. Remove all burrs and bevel the end of the shank. Failure to do so may damage the O-ring during installation and cause water leakage. Drill a 3/16" hole in the finished deck. See TEMPLATE for location. FINISHED 1/4" PLUG SHANK GUARD GUARDS REMOVE ALL BURRS AND BEVEL 5mm 1"- 2" 3/16" DRILLED HOLE SHANK Product names listed herein are trademarks of American Standard Inc. American Standard Inc mm (23/32") FRONT 8.4mm (21/64") 3/16" DIA. HOLE 18.6mm DIA. (47/64") SHANK TEMPLATE FOR ROLL PIN LOCATION
2 1 CONTINUED Lubricate the O-RING and O-RING. Push on SHANK and align slot in with 3/16" drilled hole. Tighten SET securely with 4mm. Remove the PLUG BUTTON from the. 4mm SET FINISHED O-RING O-RING 3/16" DRILLED HOLE SHANK PLUG BUTTON 5mm 2 Position the in the groove in the base of the. Push the down onto the and tighten the SET securely with the 5mm. Insert the PLUG BUTTON into the. TRIM Place the SEALS over the BODIES. Thread the S into the BODIES. Align the STEM with the as necessary. Thread the into the BODIES until the contacts the finished deck. STEM SEALS BODY 4 TESTING 5 Turn the HOT clockwise and the COLD counterclockwise to the off position. Unscrew and remove the END. Slowly turn on the water supplies. Operate the S to flush water lines thoroughly. Check connection for leakage. Turn the Handles off. Replace the END. HOT COLD END 3 INSTALL GROOVE S LEVER Turn into OFF position. Push into in a way that the male square on the fits in the female square of the. O-RING SERVICE To change the direction of handle rotation Turn off the water supplies Turn to the off position. Remove the and the. Pull the off and remove. Unscrew the. Unscrew the LOCK NUT and remove. A 17mm deep socket is required. Remove the CARTRIDGE by pulling up on the. Remove the from the CARTRIDGE. Remove the SPRING CLIP. Remove the STOP. Turn it 90 and replace. Replace the SPRING CLIP. STOP 90 LOCK NUT SPRING CLIP Push and onto STEM. Check alignment, if not satisfactory aligned; Push out carefully. Turn into OFF position. Turn either 45 or 90 so that male square on Push into. catches different female square in. Assemble and tighten. Push in top of. LEVER STEM Push and onto STEM. Push onto. Assemble and tighten. Push in top of. HOTLINE FOR HELP For toll-free information and answers to your questions, call: 1 (800) Weekdays 8:00 a.m. to 7:00 p.m. Eastern Time IN CANADA (TORONTO ) Reverse the above steps to reassembly the components. If the spout drips, operate the handles several times from the off to the on position. Do not force - the handles only turn 90 CARTRIDGE M968655A
3 MOUNT TUB FILLERS HAMPTON & PERSONAL TRIM KITS Installation Instructions T991 SERIES Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. T Trim Kits Certified to comply with ANSI A U.S. Patent No. D403,750 M T HAND SEAL HAND SEAL SEAL SEAL T T LEVER HAND SEAL LEVER HAND SEAL SEAL SEAL 1 INSTALL GUARD STEM REMOVE THE GUARD. Place the SEAL over the BODY. Thread the into the BODY. Align the STEM with the as necessary. Thread the into the BODY until the contacts the finished deck. SEAL FINISHED
4 2 INSTALL S LEVER S LEVER S LEVER LEVER Turn STEM fully clockwise (Tub Fill position). 3 Push into in a way that the male square on the fits in the female square of the. STEM Push and onto STEM. Check alignment, if not satisfactory aligned; Turn STEM fully clockwise Push out carefully. (Tub Fill position). Turn either 45 or Push into. 90 so that male square on catches different female square in. Assemble and tighten. Push in top of. INSTALL HAND Push and onto STEM. Push onto. Assemble and tighten. Push in top of. Unscrew the from the. Slip the through the and the. Insert a SEAL into the CONNECTOR. HAND Pull out the GUARD and. Unthread the GUARD from the END connection. Be careful not to allow the to fall back through the. Thread the onto the END connection and tighten securely. Apply a sealant around the HOLE. Thread the into the until the contacts the finished deck. SEAL HAND Loosen the SET in the and rotate the towards the center of the tub. Retighten the SET. Thread the into the. Insert a SEAL into the connector and connect the HAND. Place the HAND into the. GUARD SEAL END SET HOTLINE FOR HELP For toll-free information and answers to your questions, call: 1 (800) Weekdays 8:00 a.m. to 7:00 p.m. Eastern Time IN CANADA (TORONTO ) Product names listed herein are trademarks of American Standard Inc. American Standard Inc SEALANT M968357
5 MOUNT TUB SYSTEMS ROUGH KIT Installation Instructions R800 SERIES R810 SERIES R810 SERIES Thank you for selecting American-Standard... the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. R800 SERIES Certified to comply with ANSI A U.S. Patent No. D403,750 M968650C 1 ROUGHING-IN 2 FINISHED 1-3/8 D MAX. 1 D MAX. ACRYLIC BATH 4 1. THICKNESS TOTAL THICKNESS UP TO 2-1/2" 2. FINISHED FINISHED VARIABILITY ACCOMMODATES ING MATERIAL (TILE, MARBLE, CORIAN...) TO 1" THICK 1 3 FITTING SURFACE (2) 1-3/8 D HOLES 1" D 1/2" COPPER INLET SUPPLIES 8" to 12" 10" for R /8 3. FITTING SURFACE ADJUSTABILITY, TO 1-1/2" THICK 4. ACRYLIC BATHS ADJUSTABILITY, TO 1-1/2" THICK 8" to 12" 10" for R810 1" D HOLES (2) 1-3/8 D HOLES 2 MOUNT SHANK Drill holes in mounting deck as shown. The maximum allowable deck thickness is 1-1/2". Insert the SHANK through the mounting deck from below. Assemble the SHANK LOCK RING so it is flush with the top of the threads on the SHANK. SHANK LOCK RING FLUSH WITH TOP OF THREADS ON SHANK SHANK LOCK RING SHANK FRICTION NUT SHANK 1-1/2 MAX. FITTING
6 3 MOUNT BODIES Cut the copper outlet tubes of the BODIES as required. (Not necessary for R810). Insert the HOT and COLD BODIES into the TEE. (Not necessary for R810). The HOT BODY is marked with a red label. Insert the BODIES and TEE through the mounting deck from below. Assemble the LOCK RINGS so they are flush with the top of the BODIES. Insert the SHANK into the TEE. (Not necessary for R810). Tighten the BODY and SHANK NUTS securely. Fasten the LOCK RING to the wooden mounting surface with #8 screws (not provided). BODY FITTING LOCK RING FRICTION NUT LOCK RING FLUSH WITH TOP OF THREADS ON SHANK LOCK RING # 8 S HOT SHANK COLD TEE OUTLET TUBE (CUT AS REQUIRED) 4 SOLDER CONNECTIONS Connect the water supply lines to the copper inlet tubes of the BODY. Solder all TEE and WATER SUPPLY CONNECTIONS. Remove the GUARD from the SHANK. Assemble the 1/4" PLUG to the SHANK with a thread sealant. Turn on the water supplies and check all connections for leakage. Replace the GUARD on the SHANK. Turn off the water supplies. GUARD 1/4" PLUG TEE CONNECTIONS WATER SUPPLY CONNECTIONS 5 SERVICE TO CHANGE THE DIRECTION OF ROTATION DEEP SOCKET 17mm (11/16") Turn off the water supplies. Turn to the off position. Unscrew the LOCK NUT and remove. A 17mm deep socket is required. STOP 90 LOCK NUT Remove the CARTRIDGE by pulling upon the. Remove the from the CARTRIDGE. SPRING CLIP Remove the SPRING CLIP. Remove the STOP. Turn it 90 and replace. Replace the SPRING CLIP. CARTRIDGE Reverse the above steps to reassembly the components. If the spout drips, operate the handles several times from the off to the on position. Do not force - the handles only turn 90 M968650C
7 MOUNT TUB SYSTEMS MODEL NUMBERS R800 R810 LOCK RING M A LOCK NUT A A A LOCK RING A A SPINDLE A KIT M A CARTRIDGE A DEEP SOCKET 17mm (11/16") M A KIT M A R810 SERIES SOCKET NOT INCLUDED WITH FITTING HOTLINE FOR HELP For toll-free information and answers to your questions, call: 1 (800) Weekdays 8:00 a.m. to 7:00 p.m. Eastern Time IN CANADA (TORONTO ) Product names listed herein are trademarks of American Standard Inc. C American Standard Inc *WITH BRAZED TEE M968650C
8 MOUNT TUB FILLERS & PERSONAL ROUGH KIT Installation Instructions R890 SERIES Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. Certified to comply with ANSI A U.S. Patent No. D403,750 M968355D 1 ROUGHING-IN 1 1-3/8 D HOLE 1-3/8 D MAX. 6 to 18 FINISHED 2 1-3/8 D MAX. ACRYLIC BATH 4 1. THICKNESS TOTAL THICKNESS UP TO 2-1/2" 2. FINISHED FINISHED VARIABILITY ACCOMMODATES ING MATERIAL (TILE, MARBLE, CORIAN...) TO 1" THICK 3. FITTING SURFACE ADJUSTABILITY, TO 1-1/2" THICK 3 3-5/8 TUB 4-5/16 5-5/16 1-3/8 D 4. ACRYLIC BATHS ADJUSTABILITY, TO 1-1/2" THICK 1/2" NPT FITTING SURFACE SHW 1/2" NPT INLET 1-3/8 D HOLE FOR 1-3/8 D HOLE FOR HAND 6 to 18 HOLES 2 LOCATION OF R890 WHEN USED WITH R800 R800 ROUGH KIT R890 SERIES & PERSONAL ROUGH KIT 8" to 12" HOT AND COLD BODIES "A" DIMENSION CAN BE FLEXIBLE TO ACCOMMODATE CUSTOMER'S REQUIREMENTS A A 6" to 18" BATH CONNECTION HAND CONNECTION TUB HOT INLET COLD INLET 1/2" COPPER WATER TUBE INLET (MIXED SUPPLY FROM BATH FITTING) PLUMBER TO MAKE ALL PIPING CONNECTIONS BETWEEN BODIES, SUPPLY TO TRANSFER AND CONNECTION TO BATH. PIPING SHOWN SHADED IS NOT SUPPLIED AND MUST BE FURNISHED BY INSTALLER. SHW 1/2" COPPER WATER TUBE (MIXED SUPPLY TO TUB FILLER ) OUTLET (MIXED SUPPLY TO HAND )
9 3 INSTALLATION NOTE: Use thread sealant on all threaded connections. Drop the (1) into the hole in the mounting deck. 4 5 Assemble the (2) and LOCKNUT (3) to the (1) and tighten securely. For copper water tube installations, make two 4" long adapter nipples ( 1/2" Male NPT x 1/2" CWT ). Thread nipples into the inlet and tub outlet of the BODY. Tighten connections securely. Do Not Solder these Connections on the BODY. Damage may occur. Thread (4) into the CONNECTION (5) of the BODY (6) and tighten securely. Check with local plumbing codes for backflow prevention requirements. Install a backflow prevention device if required. Assemble NUT (7) and (8) onto BODY (6). Insert the BODY (6) through the mounting deck from below. Assemble the LOCK RING (9) so it is flush with the top of the BODY (6). Position the BODY (6) as required and tighten the NUT (7) securely. Fasten the LOCK RING (9) to the wooden mounting surface with #8 screws (not provided). Connect the water inlet and tub outlet lines to the BODY (6). TEST Cap the OUTLET. Remove the GUARD. Remove the GUARD. Assemble the 1/4" PLUG to the SHANK with a thread sealant. See the R800 SERIES ROUGH KIT instructions for details. Turn on the water supplies. Rotate the back and forth fully. Check all connections for leakage. Turn off the water supplies. Replace the GUARD and the GUARD. Remove the from the OUTLET. Note: Test Cap not provided. 1/2" COPPER WATER TUBE (MIXED SUPPLY TO TUB FILLER ) Insert the through the from below the mounting deck. Thread the GUARD onto the END connection. LOCK RING FLUSH WITH TOP OF THREADS ON SHANK BODY FITTING SURFACE #8 S TUB OUTLET GUARD #8 S OUTLET (MIXED SUPPLY TO HAND ) GUARD /8" Dia. HOLE FOR HAND WATER INLET 4" LONG NIPPLES 1/2" COPPER WATER TUBE INLET (MIXED SUPPLY FROM BATH FITTING) END Insert the GUARD into the. SERVICE TO REMOVE Turn off the water supplies. Turn to the off position. Remove the from by losening screw. Using 14mm (9/16") Deep Socket, remove diverter. DEEP SOCKET 14mm (9/16") M968355D
10 & PERSONAL ROUGH KIT MODEL NUMBER R890 LOCK RING M A A KIT M A A A A KIT M A M A HOT LINE FOR HELP For toll-free information and answers to your questions, call: Weekdays 8:00 a.m. to 8:00 p.m. EST IN CANADA (TORONTO ) Weekdays 8:00 a.m. to 7:00 p.m. EST IN MEXICO Product names listed herein are trademarks of American Standard Inc. American Standard Inc M968355D
Installation Instructions
Contemporary Round Floor Mounted Tub Filler Thank you for selecting American-Standard... the benchmark of fine quality for over 00 years. To ensure that your installation proceeds smoothly-- please read
More informationInstallation Instructions
Contemporary Square Floor Mounted Tub Filler Thank you for selecting American-Standard... the benchmark of fine quality for over 00 years. To ensure that your installation proceeds smoothly-- please read
More informationINSTALLATION INSTRUCTIONS
Flash Shower Valve Rough With Screwdriver Stops Thank you for selecting American-Standard... the benchmark of fine quality for over 0 years. To ensure that your installation proceeds smoothly-please read
More informationInstallation Instructions
LIFETIME UNIVERSAL DRAIN OVER THE RIM DRAIN AND STANDARD DRAIN BATH WASTE AND OVERFLOW WITH TOE TAPPER Installation Instructions 99.00.XXX Thank you for selecting American-Standard...the benchmark of fine
More informationInstallation Instructions 8115F 8115SF
TM Installation Instructions 85F 85SF Single Control Centerset Lavatory Faucet with Speed Connect Drain Congratulations on purchasing your American Standard faucet with the Speed Connect Drain, a feature
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Square Free Standing Floor Mount Tub Filler Model D35900900 Thank you for selecting DXV. To ensure that your installation proceeds smoothly, please read these instructions carefully
More informationONASSIS SHOWER SET INSTALLATION
SKU(s): 925939 BEFORE YOU BEGIN We recommend consulting a professional if you are unfamiliar with installing plumbing fixtures. Signature Hardware accepts no liability for any damage to the plumbing, floor,
More informationInstallation Instructions
ROTARY DRAIN Rotary Bath Waste And Overflow with Pop-up Drain Installation Instructions 8.SERIES BATH-DRAIN SERIES Thank you for selecting American-Standard...the benchmark of fine quality for over 00
More informationINSTALLATION GUIDELINES
STYLE No. DSXS20 with 8 Shower Head and Metal Cross Handles STYLE No. DSXS2C System with Metal Cross Handles STYLE No. DSXS30 with 8 Shower Head, Metal Lever and Cross Handle STYLE No. DSXS3C System with
More informationEXIRA SHOWER SET INSTALLATION
SKU(s): 925470 EXIRA SHOWER SET INSTALLATION BEFORE YOU BEGIN We recommend consulting a professional if you are unfamiliar with installing plumbing fixtures. Signature Hardware accepts no liability for
More informationCALLAS THERMOSTATIC SHOWER SET
SKU(s): 925945 CALLAS THERMOSTATIC SHOWER SET BEFORE YOU BEGIN We recommend consulting a professional if you are unfamiliar with installing plumbing fixtures. Signature Hardware accepts no liability for
More informationcaroma marc newson shower mixer
caroma marc newson shower mixer PLUMBERS INSTALLATION INSTRUCTIONS IS1215A(07/12) Important Information Brazed connections should NOT be made directly onto the mixer, as excessive heat will cause permanent
More informationINSTALLATION GUIDELINES
RW ATLAS Wall Mounted Lavatory Faucet Metal Wheel Handles Style No. RWLS60 IMPORTANT: INSTALLATION GUIDELINES To ensure this product is installed properly, you must read and follow these guidelines. The
More informationInstallation Instructions
TS SERIES Traditional Square Accessories Installation Instructions " TOWEL BAR.0 " TOWEL BAR.0.90 DOUBLE ROBE HOOK.0.0 " HANDLE. " HANDLE.0 Thank you for selecting American-Standard...the benchmark To
More informationInstallation Instructions 3/4 Thermostatic Valve Rough-in & Trim (PL8950)
Tub & Shower PL950 Installation Instructions 3/ Thermostatic Valve Rough-in & Trim (PL950) CONTENT 0 - Valve & stop vlave specifications 03 - Face plate specifications 0 - Handle specifications 05 - Shower
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS NOT INCLUDED NOT INCLUDED MODEL: LUGARNO HAND SHOWER SET (RH-9) Restoration Hardware Hand Shower / Slide Bar Specification Diagram SHOWN WITH SHOWER SET RH-90 (NOT INCLUDED) All
More informationMALEKO WALL-MOUNT FAUCET INSTALLATION
SKU(s): 934146 BEFORE YOU BEGIN We recommend consulting a professional if you are unfamiliar with installing bathroom fixtures and plumbing. Signature Hardware accepts no liability for any damage to the
More informationLATTIMORE SHOWER SET INSTALLATION
SKU(s): 931419 LATTIMORE SHOWER SET INSTALLATION BEFORE YOU BEGIN We recommend consulting a professional if you are unfamiliar with installing plumbing fixtures. Signature Hardware accepts no liability
More informationINSTALLATION INSTRUCTIONS FOR WALL TUB SETS, TWO HANDLE SHOWER SETS AND WALL LAVATORY SET VALVES NUMBERED: RC & RC
P 99061 INSTALLATION INSTRUCTIONS FOR WALL TUB SETS, TWO HANDLE SHOWER SETS AND WALL LAVATORY SET VALVES NUMBERED: 8090536RC & 9090536RC 2222 Camden Court, Oak Brook, IL 60523 Telephone: 800-PHYLRICH (749-5742)
More informationPressure Balance Shower Only Dual Control (Volume & Temperature) Ceramic Disc Cartridge Platinum Shower Trim Kit
Shower Only PL8900-00 & TR-SH Pressure Balance Shower Only Dual Control (Volume & Temperature) Ceramic Disc Cartridge Platinum Shower Trim Kit - Installation Instructions Before Your Installation Read
More informationTraditional Wall Mounted Potfiller
TOOLS NEEDED FOR INSTALLATION 1/4 hex wrench (provided in installation kit) 3/32 hex wrench (provided in installation kit) Pencil or marker PTFE tape Small level, or carpenters square Power Drill with
More informationcaroma marc newson wall basin mixer
caroma marc newson wall basin mixer water efficient tapware (nominal flow rate = 5 L/min) PLUMBERS INSTALLATION INSTRUCTIONS IS1213A(07/12) Important Information Brazed connections should NOT be made directly
More informationINSTALLATION GUIDELINES
IMPORTANT: To ensure this product is installed properly, you must read and follow these guidelines. The owner/user of this product must keep this information for future reference. This product must be
More informationAcrylic Claw Foot Tub
Acrylic Claw Foot Tub Wrench or socket Drill & Bits Parts Recommended 2-2 x12 boards 4 Lag Bolts 4 Flat Washers Be sure to re-inforce the floor before securing tub. We recommend 2-2 x12 s securely fastened
More informationSEBASTIAN TUB FAUCET INSTALLATION
BEFORE YOU BEGIN We recommend consulting a professional if you are unfamiliar with installing plumbing fixtures. Signature Hardware accepts no liability for any damage to the faucet, plumbing, bathtub,
More informationINSTALLATION INSTRUCTIONS FREE STANDING TUB FILLERS
INSTALLATION INSTRUCTIONS FREE STANDING TUB FILLERS Model # 2040-4261 Model # 2480-4261 Congratulations on the purchase of your Newport Brass product, an excellent choice, that will give you years of quality
More informationINSTALLATION INSTRUCTIONS FOR INSTALLING T-SERIES EXTRA HEAVY DUTY LEVER LOCKSET
HIGH EDGE 2 1/4"(57mm) 03079400070 INSTALLATION INSTRUCTIONS FOR INSTALLING T-SERIES EXTRA HEAVY DUTY LEVER LOCKSET IMPORTANT: THIS LOCK IS NON-HANDED. LOCK IS FACTORY PACKED PREADJUSTED FOR 1³ ₄" (45mm)
More informationGP-SD GENIE PROBE SMALL DIAMETER
For GENIE PROBE SMALL DIAMETER Installation and Operation Instructions 2 for s Locking Mechanism (if supplied) Set Screws Backed Out To ensure that the is Locking never accidentally loosened or Mechanism
More informationMS25 OPERATION MANUAL
SAFETY INSTRUCTIONS SPECIFICATIONS OPERATING INSTRUCTIONS MAINTENANCE ADJUSTMENTS REPLACEMENT OF PARTS MS25 DIAGRAM MS25 PARTS LIST MS25 OPERATION MANUAL SAFETY INSTRUCTIONS Please read these instructions
More informationVICTORIAN WIDESPREAD FAUCET
VICTORIAN WIDESPREAD FAUCET SKU(s): 900889, 900890, 900907, 903778, 918910, 918911 BEFORE YOU BEGIN We recommend consulting a professional if you are unfamiliar with installing plumbing fixtures. Signature
More informationWILLIS WALL-MOUNT FAUCET INSTALLATION
SKU(s): 924620 BEFORE YOU BEGIN We recommend consulting a professional if you are unfamiliar with installing bathroom fixtures and plumbing. Signature Hardware accepts no liability for any damage to the
More informationFlash Rough-In Valves
Flash Rough-In Valves American Standard I Flash Rough-In Valves I 1 Take Your Time Back At American Standard, we are constantly thinking about how our products can improve the way you work every day. Every
More informationMUELLER GAS. DH-5 Drilling Machine. For use on 1 1 /2 & 2 Line Stopper Fittings. Reliable Connections. General Information 2
operating Instructions manual MUELLER GAS TAble of contents PAGE DH-5 Drilling Machine For use on 1 1 /2 & 2 Line Stopper Fittings General Information 2 Installing and Stopping-off 1 1 /2 and 2 Line Stopper
More informationWILLIS WIDESPREAD FAUCET
SKU(s): 924621 WILLIS WIDESPREAD FAUCET BEFORE YOU BEGIN We recommend consulting a professional if you are unfamiliar with installing plumbing fixtures. Signature Hardware accepts no liability for any
More informationCaution: Installation and Operation Instructions. Locking Mechanism (if supplied) Set Screws Backed Out. Mounting Orientation
Genie Probe Regulator (GPR)/ Genie Probe (GP2)/ Genie Probe for Composite Sampler (CSA)/ And (Model H) Installation and Operation Instructions Caution: Not designed for external fire. Prior to use in a
More informationwww.wildmanconstruction.com Changing your toilet is an easy project that should take half a day or less. The most common toilet has a separate tank that mounts on top of the bowl. These instructions apply
More informationH8508 Impact Wrench SERVICE MANUAL. Model (Serial Code FWN) Model (Serial Code FWP)
SERVICE MANUAL H8508 Impact Wrench Model 48755 (Serial Code FWN) Model 48760 (Serial Code FWP) Read and understand all of the instructions and safety information in this manual before operating or servicing
More informationMUELLER. Improved, Centurion Series, Modern Improved, and 107. Fire Hydrants. Inserting Extention Sections. Reliable Connections
insertion Instructions manual MUELLER Improved, Centurion Series, Modern Improved, and 107 table of contents PAGE Centurion Series Fire Hydrant Adding an Extention 2-3 Improved Fire Hydrant Inserting Extention
More informationBodyspray INSTALLATION INSTRUCTIONS
Bodyspray P22077 P22079 2014 KALLISTA 1 of 8 THANK YOU FOR CHOOSING KALLISTA Bodyspray We appreciate your commitment to KALLISTA quality products. Please take a moment to review this manual before you
More informationStep by Step Installation Instructions. Poly Shutters. Customer Service or visit us online at smithandnoble.com
Step by Step Installation Instructions Poly Shutters Customer Service 800.248.8888 or visit us online at smithandnoble.com Thank you for purchasing from smith+noble. Your new window treatments have been
More informationChiltern Model Steam Engines
Chiltern Model Steam Engines Mill Twin Cylinder Model Steam Engine v2 Assembly Instructions v1.0 Notes: 1. In overview the engine should first be assembled "dry" with no oil/lubricants, thread lock or
More informationOTECO INC. MODEL ,000 PSI 4-1/16 PORT DM GATE VALVE MAINTENANCE MANUAL
Page 1 of 7 OTECO INC. MODEL 45 4 5,000 PSI 4-1/16 PORT DM GATE VALVE MAINTENANCE MANUAL Page 2 of 7 TABLE OF CONTENTS 1. Assembly Blowout 2. Repair Kit Contents & Technical Specifications 3. Disassembly
More informationMUELLER. Improved, Centurion Series, Modern Improved, and 107. Fire Hydrants. Inserting Extension Sections. Reliable Connections
insertion Instructions manual MUELLER Improved, Centurion Series, Modern Improved, and 107 table of contents PAGE Centurion Series Fire Hydrant Adding an Extension 2-3 Improved Fire Hydrant Inserting Extension
More informationFig. 2 DORMA-Glas Stand/Issue 02/03 Seite/Page 1/7
FSW Installation instructions Track rail 75 x 72 mm 1. Ceiling substructure and installation of the track rail (Fig. 1): The track rail must be bolted over its entire length (including the stacking track
More informationEP-60 END OF CAR JUNCTION BOX KIT and ASSEMBLY AND INSTALLATION INSTRUCTIONS
EP-60 END OF CAR JUNCTION BOX KIT 786282 and 786438 ASSEMBLY AND INSTALLATION INSTRUCTIONS Figure 1 EP-60 End of Car Junction Box Kit Item No. Qty. Description P/N Kit No. 786282 Kit No. 786438 1 2 Screw,
More informationGeneral Array Layout Sketch
General Array Layout Sketch Cold TO Panels Hot FROM Panels OR Cold TO Panels Hot FROM Panels 1 Introduction This document describes how to install EZ series panels. The EZ series panels are designed to
More informationROTUNDA WALL-MOUNT FAUCET INSTALLATION
SKU(s): 919045 BEFORE YOU BEGIN We recommend consulting a professional if you are unfamiliar with installing bathroom fixtures and plumbing. Signature Hardware accepts no liability for any damage to the
More informationPet Door Panel Installation Manual
Pet Door Panel Installation Manual 400-558-1 1 4/3/03, 3:26 PM Components: Pet Door Panel Panel Latch Assembly Foam Weather-stripping Glass Sweep (4) Binding Posts (6) #6 x 1/2 Sheet Metal Screws (4) 8-32
More informationBathroom Installation Guide
Bathroom Installation Guide Please read instructions carefully and check products before starting. Products should be fitted/installed by an experienced and competent fitter, failure to do so may invalidate
More informationCut-True 16M Manual Paper Cutter
Cut-True 16M Manual Paper Cutter 2/2013 OPERATOR MANUAL FIRST EDITION TABLE OF CONTENTS TOPIC PAGE Specifications 1 Safety Guidelines 1 Assembly 2 Overview 3 Description of Equipment Parts 3-4 Operation
More informationShim (2) Supplied. Strike Plate. (3) x 5/8" PFHMS or 10 x 1" PFHWS. Top Latch. (3) x 1/4" PRHMS. Latch Cover. (2) 8 x 3/8" PFH AB SMS
Installation Instructions ED5400 (A) Series ED5470 (B) Series Surface Vertical Rod Exit Devices Strike Angle Must Engage Strike Top Strike 10-24 PFHMS Top Bracket and Strike required for ED5470. Shim (2)
More informationSHUR-LOK CORPORATION TECHNICAL SALES BULLETIN
Page 1 of 11 1.0 INTRODUCTION: 1.1 This Technical Sales Bulletin describes installation procedure of SL850 Blind-Threaded and SL854 Thru-Threaded Pull-up type inserts. These procedures use the SLPGA850
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS TOOLS REQUIRED Rechargeable, variable speed drill 3/8 diameter drill bit 3 Robertson bits #0, #1 and #2 Slot screwdriver Non marring hammer with 1 head Level Caulk or sealant
More informationClocking a TD-04 Turbo Compressor Housing. Appendix A : AWIC Silicone and Tubing Fitting
Clocking a TD-04 Turbo Compressor Housing Appendix A : AWIC Silicone and Tubing Fitting Revision A: 7-13-2015 Tools: Metric Sockets (10, 12, 14, 17mm) 5mm Hex Key Large Internal Snap Ring Pliers 3/8 Socket
More informationMechanical Frappe Press
Mechanical Frappe Press Operation Manual CONTENTS OPERATIONAL INSTRUCTIONS PRECAUTIONS PART NAMES INCLUDED ITEMS BASIC OPERATION MAINTENANCE REPLACEMENT PARTS Thank you for using The Frapptastic Five Mechanical
More informationFor installation assistance, contact SARGENT at DOORS SHOWN HERE SWING IN FOR ILLUSTRATION PURPOSES ONLY.
SARGENT Installation Instructions for LP8600 x LR8600 & 12-LP8600 x 12-LR8600 Series Low Profile Panic and Fire Exit Devices on Double Egress & Double Doors or LS8600 & 12-LS8600 Low Profile Exit Device
More informationSHELTON THERMOSTATIC SHOWER PANEL
SKU(s): 413241 BEFORE YOU BEGIN We recommend consulting a professional if you are unfamiliar with installing plumbing fixtures. Signature Hardware accepts no liability for any damage to the plumbing, floor,
More informationBETTIS SERVICE INSTRUCTIONS FOR MODELS G01 THROUGH G10 SERIES HYDRAULIC SPRING RETURN ACTUATORS WITH M11 HYDRAULIC OVERRIDE
ENGLISH LANUAGE BETTIS SERVICE INSTRUCTIONS FOR MODELS G01 THROUGH G10 SERIES HYDRAULIC SPRING RETURN ACTUATORS WITH M11 HYDRAULIC OVERRIDE PART NUMBER: 127072E REVISION: A DATE: December 2001 Page 1 of
More informationBSM, GSM & GSS. Joint Kit Instruction. (Modified for IMPACT) (NSF Certified) Curved Glass Fresh Meat Delicatessen and Seafood Merchandisers
BSM, GSM & GSS Joint Kit Instruction (Modified for IMPACT) (NSF Certified) Curved Glass Fresh Meat Delicatessen and Seafood Merchandisers February, 1999 JOINT ASSEMBLY PARTS LIST Item Quantity Description
More informationBETTIS SERVICE INSTRUCTIONS FOR MODELS G01 THROUGH G13 SERIES HYDRAULIC ACTUATORS WITH POWER MODULE TIE BAR CONSTRUCTION
ENGLISH LANGUAGE BETTIS SERVICE INSTRUCTIONS FOR MODELS G01 THROUGH G13 SERIES HYDRAULIC ACTUATORS WITH POWER MODULE TIE BAR CONSTRUCTION PART NUMBER: 124839E REVISION: C DATE: 06 July 2006 Page 1 of 31
More informationA SRF/SERF A SRF/SERF
A1100-055SRF/SERF A1100-056SRF/SERF Remote Fill Assembly INSTALLATION INSTRUCTIONS **CRITICAL - MUST READ** This unit can only be used for new installations or tank level retrofits that allow access to
More informationThermostatic Valve Trim
Thermostatic Valve Trim P23052-CR, P23052-LV, P23122-LV, P23222-RK, P23222-LV, P24022-CL, P24022-CR, P24022-KL, P24022-RB, P24022-RL, P24122-CR, P24122-LV, P24129-CR, P24129-LV, P24421-CR, P24421-LV, P24422-CR,
More informationHALSEY TAYLOR OWNERS MANUAL Contour TM Series Barrier-Free Water Coolers Refrigerated Fountains with Back Panel
HALSEY TAYLOR OWNERS MANUAL Contour TM Series BarrierFree Water Coolers Refrigerated Fountains with Back Panel Figure HRFSERQ Figure HRFERQ Figure HRFSRQ Figure Not Shown Model HRFSERQ HRFERQ HRFSRQ HRFESRQ
More informationTools Needed Hardware Provided (per shade) Hardware Needed
Baby Grande or Grande Motorized (XQ5 Premium) Shade with Cables and Housing Installation Instructions Tools Needed Hardware Provided (per shade) Hardware Needed Drill 3/8 Metal Drill Bit Measuring Tape
More informationCRCODE-202. Mechanical Lock. Instruction and Programming Manual. Before Installing:
CRCODE-202 Mechanical Lock Instruction and Programming Manual Before Installing: 1. Please read the instructions carefully to prevent missing important steps. *Note: Improper installations may result in
More informationInstallation Instructions
EZ Launch Accessible Transfer System Installation Instructions Models 500900L, 500900R, 500901L, 500901R 500890, 500906L, 500906R For questions about features, operation/performance, parts, accessories
More informationLPK1550 Hydraulic Crimping Tool 15-ton
SERVICE MANUAL LPK1550 Hydraulic Crimping Tool 15-ton Serial Code FYF Read and understand all of the instructions and safety information in this manual before operating or servicing this tool. Register
More informationA500 ASSEMBLY & INSTALLATION INSTRUCTIONS
ASSEMBLY & INSTALLATION INSTRUCTIONS 1 CONTENTS 2 Component Parts A B Canopy Mounting Plate C Cap (3) D Threaded Nipple E Threaded Standoffs (2) F Anchors (8) G #10 Screws (8) H Safety Cable (2) I Safety
More informationChin Strap, Sealed Pull Pins and Swing Catch for Fiberglass Helmets. Contents
Chin Strap Chin Strap, Sealed Pull Pins and Swing Catch for Fiberglass Helmets Contents BTM-1 1.1 Chin Strap BTM-4 1.2.3.1 Preparation BTM-1 1.1.1 Chin Strap Removal BTM-4 1.2.3.2 Disassembly BTM-1 BTM-2
More informationDublin Stalls Installation Instructions
Dublin Stalls Installation Instructions RAMM Horse Fencing and Stalls 13150 Airport Hwy. Swanton, OH 43558-9615 1-800-434-8456 Rev. 9/13/17 Part Identification Round Track Bracket (4) (Not Painted) Round
More informationCAELI THERMOSTATIC SHOWER PANEL
SKU(s): 300280 CAELI THERMOSTATIC SHOWER PANEL BEFORE YOU BEGIN We recommend consulting a professional if you are unfamiliar with installing plumbing fixtures. Signature Hardware accepts no liability for
More informationThis product is designed for a water supply pressure range of 20 psi (137kPa) minimum to 80psi (550 kpa) maximum.
We appreciate your commitment to Kohler quality. Please take a few minutes to review this manual before you start installation. If you encounter any installation or performance problems, please don t hesitate
More informationB-Too Drilling and Tapping Machine Instruction and Maintenance Manual
B-Too Drilling and Tapping Machine Instruction and Maintenance Manual Thank you for your purchase of the B-Too Drilling and Tapping Machine. Please read and understand this short operation manual. Our
More informationSUPER PRO GUN & SUPER PRO GUN II
MAGNUM VENUS PRODUCTS Maintenance & Repair Manual Part No. M6707-1-1 Revision 04.14.01 Maintenance & Repair Corporate HQ & Mfg. Phone: (727) 573-2955 Fax: (727) 571-3636 Email: info@magind.com Web: www.magind.com
More informationLow Base 3, 4 and 5-Piece Showers with SnapJoint 3/4/5 LBS SJ
ARCHITECTURALS INC. Architectural Products for Barrier Free Living Barrier Free Architecturals 2788 Bathurst Street Toronto, On Canada M6B3A3 1(877) 717-7027 or visit: www.barrierfree.org EMAIL: info@barrierfree.org
More informationTABLE OF CONTENTS REQUIRED TOOLS
TABLE OF CONTENTS SECTION SECTION TITLE PAGE NO. 1 2 3 4 5 Assembling Mounting Structure Installing Bicycle Supports Mounting Rack to Wall Adding Sections Customizing Rack Configuration REQUIRED TOOLS
More informationThe Virgo/Libra Steam Engine
The Virgo/Libra Steam Engine Congratulations on becoming the owner of a Virgo or Libra Steam Engine. With careful use and maintenance it will give many years of satisfying performance. Contents 1) Notes
More informationHB Coupling Expander Instructions
HB Coupling Expander Instructions Vice or Bench Mounted Hand Operated Pull Through Type Used to attach: All 520-H Series Holedall Petroleum fittings ¾" - 2" All 570-H & 580-H Series Holedall Petroleum
More informationINSTRUCTIONS FOR USE Pro-Ject 9 Pro-Ject 9c Pro-Ject 9cc Pro-Ject 10cc Pro-Ject 12cc
INSTRUCTIONS FOR USE Pro-Ject 9 Pro-Ject 9c Pro-Ject 9cc Pro-Ject 10cc Pro-Ject 12cc 1 Finger lift * 2 Headshell 3 Tonearm tube 4 Tonearm rest 4a Removable transport lock 5 Tonearm lift lever 6 Anti-skating
More informationHQ Hideaway. Installation and Operation Version 2.2, April 2015 Part # QT40100
HQ Hideaway Installation and Operation Version 2.2, April 2015 Part # QT40100 Copyright 2015 Handi Quilter, Inc. All rights reserved. Printed in the U.S.A. Table of Contents Page Overview 3 To install
More informationHYDRO-TOWER INSTALLATION INSTRUCTIONS
HYDRO-TOWER INSTALLATION INSTRUCTIONS IN-WALL TANK K-06T-PNE/K-06K-PNE/K-07T-PNE/K-07K-PNE K-08T-PNE/K-08K-PNE/K-78073T-PNE/K-78073K-PNE K-78074T-PNE/K-78074K-PNE/K-78075T-PNE/K-78075K-PNE K-20341T-PNE
More informationSnap Tabs, Chin Strap, Swing Catch, Sealed Pull Pins Stainless Steel. Contents
Snap Tabs, etc. Stainless Steel Helmets Snap Tabs, Chin Strap, and Earphone Retainers Snap Tabs, Chin Strap, Swing Catch, Sealed Pull Pins Stainless Steel Contents SSBTM-1 1.1 Snap Tabs, Chin Strap, and
More information1. Fasten press to bench or work surface using the mounting holes provided (Item 3).
INSTRUCTIONS AND PARTS LIST FOR Models 1-202, 1-204, 1-210, and 1-220 Air Arbor Presses WARNING LABELS To the left is the safety Alert symbol. When you see these safety alert symbols on your press, be
More informationTOOLS REQUIRED Metal Wood Wood and Metal Screws. #16 Drill #12-24 Tap. 1/8 Drill
DEVICES COVERED IN THIS DOCUMENT: 4700S Surface Vertical Rod Device 4700SF Fire Exit Surface Vertical Rod Device TOOLS REQUIRED Metal Wood Wood and Metal Screws Sex Bolts #7 Drill ¼ -20 Tap #16 Drill #12-24
More informationDiptych Bath Screen Installation Guide
v1 These instructions are for left and right handed screens. The diagrams show a right handed screen. Page i Thank you for purchasing this Diptych Bath Screen. Please study these instructions carefully
More informationINSTALLATION GUIDE 2009-CURRENT HUMMER H3T PRODUCT CODE:
INSTALLATION GUIDE 2009-CURRENT HUMMER H3T PRODUCT CODE: 268 June 22, 2010 TOOLS NEEDED COMPONENTS INCLUDED P2 Tip 3/8" Drill Rubber Gasket(s) x 2 Bracket(s) x 2 1/2" Drill Bit Bulkhead Flange #2 Phillips
More informationWHITE ARCHIPELAGO PRESSURE BALANCE MIXING VALVE TRIM ONLY, TO SUIT M ROUGH
INSTALLATION INSTRUCTIONS CW-00 WHITE ARCHIPELAGO PRESSURE BALANCE MIXING VALVE TRIM ONLY, TO SUIT M-0 ROUGH CB-00 BLACK ARCHIPELAGO PRESSURE BALANCE MIXING VALVE TRIM ONLY, TO SUIT M-0 ROUGH CW-0 WHITE
More informationLaminate Cabinet Installation Instructions
Laminate Cabinet Installation Instructions www.easygaragestorage.com/installation How To Use These Instructions Thank you for your purchase! Please read each step of this manual thoroughly to ensure proper
More informationInstallation Instructions ED4400, ED4400M & ED4400MA Series Surface Vertical Rod Exit Devices
Installation Instructions ED4400, ED4400M & ED4400MA Series Surface Vertical Rod Exit Devices In U.S.: Corbin Russwin, Inc. 225 Episcopal Road Berlin, CT 06037 USA www.corbinrusswin.com In Canada: Door
More informationSERVICE INSTRUCTIONS Model 9670 Lubricant Pump
TM TM SERVICE INSTRUCTIONS Model 9670 Lubricant Pump 9670 DESCRIPTION Model 9670 Lubricant Pump is designed to pump light to heavy oils directly from the original container. This design features a 10:1
More informationBALANTINE WALL-MOUNT FAUCET INSTALLATION
SKU(s): 911574, 911575 BALANTINE WALL-MOUNT FAUCET INSTALLATION BEFORE YOU BEGIN We recommend consulting a professional if you are unfamiliar with installing bathroom fixtures and plumbing. Signature Hardware
More informationED5800 (A) Series. Installation Instructions. Concealed Vertical Rod. Exit Device WARNING
Strike Shim (2) Supplied Strike Plate (3) 10-24 x 3/4" PFHMS (6) 10-24 x 1/2" PFHMS Top Latch TopTube Concealed Vertical Rod Exit Device Important: For use with metal doors only. Device is packed ready
More informationREPAIR INSTRUCTIONS. Cat. No Cat. No MILWAUKEE ELECTRIC TOOL CORPORATION. SDS Max Demolition Hammer. SDS Max Rotary Hammer
Cat. No. 9-0 SDS Max Demolition Hammer Cat. No. -0 SDS Max Rotary Hammer MILWAUKEE ELECTRIC TOOL CORPORATION W. LISBON ROAD BROOKFIELD, WISCONSIN 00-0 8-9-0 d 000 8-9-0 d Special Tools Require Forcing
More informationReliance SG800 Series Steel Water Gage Valves
Installation, Operation, & Maintenance Instructions R500.541D1 10/16/2016 Reliance SG800 Series Steel Water Gage Valves Note: Design variations in Steel Water Gage Valves necessitate typical illustrations,
More informationREPLACEMENT TARP for SRT-2 SPOOL ROLL TARP
REPLACEMENT TARP for SRT-2 SPOOL ROLL TARP NOTICE TO INSTALLER: Even if familiar with product, read instructions prior to installation as improvements may be made without notice. Always handle components
More informationInstallation and Maintenance Instructions
Limited One Year Warranty T&S warrants to the original purchaser (other than for purposes of resale) that such product is free from defects in material and workmanship for a period of one (1) year from
More informationHANDHOLE SEAT GRINDER
1041-1601 HANDHOLE SEAT GRINDER OPERATING INSTRUCTIONS & SERVICE MANUAL Rev: A, 9/17/2007 TO REDUCE THE RISK OF INJURY AND EQUIPMENT DAMAGE USER MUST READ AND UNDERSTAND OPERATOR S MANUAL. Thomas C. Wilson,
More informationB235 Mobius Sconce Page 1 of 6
Mobius Sconce 28-9450 Page 1 of 6 CAUTION: FAILURE TO INSTALL THIS PRODUCT PROPERLY MAY RESULT IN PERSONAL INJURY OR PROPERTY DAMAGE. We recommend installation by a qualified individual trained in the
More informationGLENBROOK/GLENGUARD VITREOUS CHINA DRINKING FOUNTAIN/CUSPIDOR
GLENBROOK/GLENGUARD VITREOUS CHINA DRINKING FOUNTAIN/CUSPIDOR BEFORE YOU BEGIN HOW TO USE THESE INSTRUCTIONS Please read these instructions carefully to familiarize yourself with the required tools, materials,
More information