Visions Tub Door & Backwall

Transcription

1 Visions Tub Door & Backwall TUB DOOR & BACKWALL INSTALLATION INSTRUCTIONS IMPORTANT DreamLine reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings, manuals, warranty information or additional details please refer to your model s web page on DreamLine.com STEP : Tub Backwall Installation Instructions STEP : Tub Door Installation Instructions For more information about DreamLine Shower Doors, Tub Doors & Enclosures, please visit DreamLine.com VISIONS TUB DOOR & BACKWALL 07 DreamLine. All Rights Reserved

2 Q-WALL TUB BACKWALL ACRYLIC BACKWALL INSTALLATION INSTRUCTIONS IMPORTANT DreamLine reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings, manuals, warranty information or additional details please refer to your model s web page on DreamLine.com MODEL #s SHBW For more information about DreamLine Shower Doors, Tub Doors & Enclosures, please visit DreamLine.com Q-Wall Tub manual Ver Rev /07 07 DreamLine. All Rights Reserved

3 Table of Contents Page # Section title Preparation Tools Detailed Diagram of Shower Wall Components 4 Parts List 5 Installation Steps 6-8 Tub Glass Shelves Installation (optional) 9 Product Maintenance 3 Overall Dimensions 56 " " 56"--- 60" 60" Q-Wall Tub manual Ver Rev /07 8"--- 3" 8 8"--- 3" " -3 "-- 07 DreamLine. All Rights Reserved

4 Preparation. Prior to installation, examine all boxes and packages for shipping damage and compare the piece count with the packing slip. After opening all boxes and packages read this introduction carefully. Check that all of the necessary parts are included in the package by checking off the components on the Detailed Diagram of Shower Door Components. If the unit has been damaged, has a finishing defect, or has missing parts, please contact our customer support department within 3 business days of the delivery date. Please note that DreamLine will not replace any damaged products or missing parts free of charge after 3 business days or if the product has been installed. Contact DreamLine if you have any questions, and please provide an order number, job name or other proof of purchase to help identify the original order.. Please note that you should consult your local building codes with questions on installation compliance standards. Building and plumbing codes may vary by location, and DreamLine is not responsible for code compliance standards for your project and will not accept any returns. 3. This acrylic wall system is specially designed to be installed over any solid surface. If you are installing the acrylic walls over the existing tiles, remove all loose tiles before the installation. If you are installing over the existing painted walls, remove all loose paint. Note that some cutting and drilling will be necessary during the installation process. 4. Make sure to turn off the water supply, remove faucet, handles or any fixture trims protruding from the wall. Remove any soap film and dirt from all wall surfaces using regular household detergent, then wipe dry. 5. If this unit is going to be installed in a new construction, please install all of the required plumbing and drainage before installing the shower. Use a competent and licensed (if required by local code) plumber for all plumbing installation. 6. Side walls must be trimmed to size in most cases (straight edge and a razor knife or other tool suitable for trimming acrylic). Use a straight edge and score the acrylic wall several times to cut to size. 7. Use an adhesive that is safe to use with acrylic walls: i.e. LN75, LN95 etc. Use caulk to seal around the bottom/ top edges, top corners and around any fixture cutouts. 07 DreamLine. All Rights Reserved 8. Designed to be installed over drywall or tile not intended for installation against bare studs. 9. Making cutouts for shower fixtures will not void the warranty. However making cutouts for window openings will void the warranty. 0. Professional installation recommended. Q-Wall Tub manual Ver Rev /07

5 Tools Tape Measure Level T-Square Hole Saw Caulk Pencil Power Drill Knife Hammer Drill bit (Ø 5/6") Phillips Screwdriver (acrylic safe) Adhesive to be sure that the correct model size has been ordered.! Tip: Prior to installation, cover the shower/tub drain with tape to prevent losing screws or small parts.! Tip: Set screw gun clutch to low setting when installing screws and bolts to prevent stripping the heads. 07 DreamLine. All Rights Reserved Tip: Measure the opening before proceeding with the installation! NOTE: Unpack your unit carefully and inspect it. Lay it out and identify all parts using the detailed diagram and packing list in this manual as a reference. Before discarding the carton, check for small hardware bags that may have fallen to the bottom of the box. If any parts are damaged or missing, please contact DreamLine for replacement. The shipping boxes may contain extra parts not used in your model configuration. NOTE: Retain these installation instructions for future reference. Q-Wall Tub manual Ver Rev /07 3

6 Detailed Diagram of Shower Wall Components DreamLine. All Rights Reserved 0 Q-Wall Tub manual Ver Rev /07 4

7 Parts List ITEM # PART NUMBER DESCRIPTION QTY Side panel pcs Back panel pcs Decorative edge molding pcs Corner cover pcs Center cover pc Wall anchor pcs Countersunk screw ST4. 30 pcs Decorative cover 5pcs Glass shelf pcs Shelf bracket 6pcs 07 DreamLine. All Rights Reserved 0 Q-Wall Tub manual Ver Rev /07 5

8 Installation steps. Measure the distance of the back wall of W the tub from corner to corner. Record this measurement as W. (Fig ) W W Fig. Divide the W measurement in half (W/). W/ Draw a plumb line to mark the center of the back wall (Fig ) 07 DreamLine. All Rights Reserved W/ Fig Q-Wall Tub manual Ver Rev /07 6

9 3. Measure the side walls from the corner to the front point where the Side Panel (#0) will be trimmed to size. Record this measurement as D. (Fig 3) D D Fig 3 Draw plumb Vertical Reference lines from the corners 4a. Measure from the corners and draw plumb, 07 DreamLine. All Rights Reserved vertical reference lines on the walls at both corners. (Fig 4a ) Fig 4a Q-Wall Tub manual Ver Rev /07 7

10 4b. Measure the location of the holes on the wall S = (D- ) where the fixtures will be installed. Use these measurements to drill the cutouts in the corresponding Side Panel (#0) in Step #7. " A back Take exact measurements: corner of walls from the vertical reference line to the center of the fixture holes: (A, B, C, G) from the tub deck up to the center of the fixture holes: (E, F, H). (Fig 4b) Vertical Reference line from corner! Note: This diagram represents the wall, not the acrylic side panel. Note: This diagram represents a typical fixture hole layout. E F Measure from the Vertical Reference line from corner H B Trim line Measure the fixture locations on the wall C G D Fig 4b Record all applicable dimensions here: A shower head B lever C lever D 07 DreamLine. All Rights Reserved S (D- ) trim line E F G tub filler H Right side wall fixtures shown as an example Q-Wall Tub manual Ver Rev /07 These dimensions will be used in Step#7 to drill the holes into the acrylic Side Panel (#0). 8

11 5. Place the Center Cover (#05) vertically on the back wall centerline (from Step#) and mark the drilling holes through the predrilled holes in the Center Cover (#05). Drill the holes using a Ø5/6 drill bit and insert the Wall Anchors (#06). (Fig 5a and Fig 5b) 3 4 Ø5/6 Fig 5a Fig 5b 6. Place the Corner Cover (#04) to the corner of the wall and mark the drilling holes through the DreamLine. All Rights Reserved predrilled holes in the Corner Cover (#04). Drill the holes using a Ø5/6 drill bit and insert the Wall Anchors (#06). (Fig 6a and Fig 6b) Ø5/6 Fig 6a Q-Wall Tub manual Ver Rev /07 Fig 6b 9

12 reference line 7. Determine the finished cut size for both Back Panels (#0). centerline (If the finished overall width of the back wall= 59-/ from corner-to-corner, then it will not be necessary to trim the back panels. Proceed to Step #9). L NOTE: (a) = Narrow edge (3-3/8 ) toward the center line on the back wall. (do not trim this edge) (b) = Wider edge (4-5/8 ) toward the corner of the back wall. (trim this edge only) Measure the back wall from the reference line in the corner to the center line drawn in Step#. This will be dimension L. Trim the back panel to this dimension, cutting from the wider edge (b) of the back panel only. (Fig 7a) Place a mark on the wider (b) edge of the Back Panel (#0) with a distance of L from the (a) edge of the Back Panel (#0). Use a straight edge and draw a straight cut line from top to bottom. (Fig 7b) this edge to corner L Fig 7a these edges to center L b a this edge to corner 07 DreamLine. All Rights Reserved b Fig 7b Q-Wall Tub manual Ver Rev /07 0

13 8. Place the Back Panel (#0) onto a flat piece of plywood or particle board. Use a T-square and a sharp industrial knife to score along the cut lines (from the previous step) on the Back Panel (#0) and continue scoring until fully cut through the panel. (Fig 8a and Fig 8b) L L a Fig 8a Fig 8b 9. Install the Center Cover (#05) to the center of the back wall using the Countersunk Screws ST4. 30 (#07). Do not fully tighten the screws yet. Leave the Center Cover (#05) loose on the wall for now. (Fig 9) 07 DreamLine. All Rights Reserved 0. Apply adhesive to the entire back surface of the left Back Panel (#0). (Fig 0) Fig 9 Fig 0 Q-Wall Tub manual Ver Rev /07

14 . Slide the right edge of the left Back Panel (#0) behind the Center Cover (#05) and push the Back Panel (#0) flat against the wall up to the vertical reference line in the corner. Adjust the position of the Back Panel (#0) before the adhesive sets. Apply equal pressure to the whole surface of the Back Panel (#0) from top to bottom. Fasten the Corner Cover (#04) to the left corner of the backwall using the Countersunk Screws ST4. 30 (#07). Do not fully tighten the corner cover screws yet. (Fig ) 3 Fig. Repeat Step#0 and Step# to install the right Back Panel (#0) to the right side of the back wall. (Fig ) 6 07 DreamLine. All Rights Reserved 5 4 Fig Q-Wall Tub manual Ver Rev /07

15 3. Align both Back Panels (#0) at the top and tighten the screws on the Center Cover (#05) to secure this assembly in place. Do not tighten the screws on the corner covers yet. (Fig 3a and Fig 3b) Fig 3b Fig 3a reference line Trim line S Note: Refer to the D dimension from Step #3 to determine the finished cut size S for the Side Panel (#0) in the next steps. (D - = S) 4. Measure from the reference line to the D 07 DreamLine. All Rights Reserved dimension line from Step #3. This will be dimension S. (Fig 4) Fig 4 Q-Wall Tub manual Ver Rev /07 3

16 5. Mark the finished cut size S for both Side these edges to the corners Panels (#0). NOTE: (a) = Narrow edge (3-3/8 ) toward the corner reference line (do not trim this edge) S S (b) = Wider edge (6-3/8 ) toward the outside of the side wall. (trim this edge only) Trim the side panels to the S dimension, cutting from the wider edge (b) of the side panels only. a b Place a mark on the wider edge (b) of the Side Panel (#0) to the dimension of S from the corner side of the Side Panel (#0) to the front edge and draw a straight cut line from top to bottom. (Fig 5) b Fig 5 this edge to outside this edge to outside 6. Place the Side Panel (#0) onto a flat piece of plywood or particle board. Use a T-square and a sharp industrial knife to score along the cut lines (from the previous step) on the Side Panel (#0) and continue scoring until fully cut through the panel. (Fig 6a and Fig 6b) S S 07 DreamLine. All Rights Reserved a Fig 6a Fig 6b Q-Wall Tub manual Ver Rev /07 4

17 7. Transfer the fixture hole measurements (from Step #4) onto the Side Panel (#0) that will be installed onto the wall with the fixtures. Drill the holes in the Side Panel (#0) using the appropriate diameter hole saw or a handheld jig saw. (Fig 7a and Fig 7b) Hole Saw! NOTE: Be sure to drill the holes on the correct surface of the side panel to match the dimensions from Step# Fig 7a Fig 7b Right side wall fixtures shown as an example 8. Apply adhesive to the entire back surface of the Side Panel (#0) 07 DreamLine. All Rights Reserved and around the drilled fixture holes. (Fig 8) Fig 8 Q-Wall Tub manual Ver Rev /07 5

18 9. Slide the edge of the Side Panel (#0) behind the Corner Cover (#04) and push the Side Panel (#0) flat against the wall up to the vertical reference line toward the outside of the tub (Fig. 9a.3). Align the top of the Side Panel (#0) with the Back Panel (#0) before the adhesive sets. Apply equal pressure to the whole surface of the Side Panel (#0) from top to bottom. *Peel off the adhesive tape on the back side of the Decorative Edge Molding (#03) and attach it to the front edge of the Side Panel (#0). Apply pressure to the Decorative Edge Molding (#03) from top to bottom. (Fig 9a) 3 4 Fig 9a TIP: *If also installing a shower door, the wall profile can be installed to hide the edge of the Side Panel (#0) behind the wall profile and not use the Decorative Edge Molding (#03). (Fig 9b) Wall Profile Side Panel Side Panel Wall Profile Wall Fig 9b 0. Apply adhesive to the entire back surface of the Side Panel (#0) 07 DreamLine. All Rights Reserved for the opposite side wall installation. Use the same technique to apply pressure over the entire surface and make the top edge even with the adjacent acrylic wall panel. (Fig 0) Fig 0 Q-Wall Tub manual Ver Rev /07 6

19 . Repeat Step#8 to install the second Side Panel (#0), tucking the Side Panel (#0) behind the corner cover and fully tightening the screws. (Fig a and Fig b) 3 4 Fig a Fig b. Tighten the screws for the Corner Covers (#04) and the Center Cover (#05) to secure the Side Panels (#0) and the Back Panels (#0) in place. (Fig ) 07 DreamLine. All Rights Reserved Fig 3. Use the Decorative Covers (#08) to cover the screw holes in the Corner Covers (#04) and the Center Cover (#05). (Fig 3) Fig 3 Q-Wall Tub manual Ver Rev /07 7

20 4. Apply a good quality mildew-resitant caulk or silicone along the top edge of the panels and corner covers and along the connection of the bottom edges of the panels with the tub. (Fig 4)! Allow 4 hours for the adhesive and silicone/caulk to cure before using the shower. 4 Hours Fig 4 To install the optional Glass Shelves (#09), continue onto the next steps. 07 DreamLine. All Rights Reserved! ATTENTION: The installation of the Q-WALL-Tub walls is complete. Q-Wall Tub manual Ver Rev /07 8

21 Glass Shelves Installation Instruction (optional) 5. Determine the preferred height for the Glass Shelves (#09) and mark the locations on the wall. (Fig 5) NOTE: Both Glass Shelves can be installed in one corner, or one shelf in each corner. G H Fig 5 6. Mark the location for the Shelf Brackets (#0) according to the measurements in Fig 5.. Drill the holes using Ø5/6 drill bit and insert the Wall Anchors (#06). (Fig 6) 3-/" 3-/" 3 07 DreamLine. All Rights Reserved 3-/" Ø5/6" Fig 6 Q-Wall Tub manual Ver Rev /07 9

22 7. Mount the Glass Brackets (#0) to the wall using the Countersunk Screws ST4. 30 (#07). NOTE: The Glass Brackets (#0) should be installed with the set screws on the bottom. Slide the upper Glass Shelf (#09) into the Glass Brackets (#0) and tighten the set screws at the bottom of the brackets. Then slide the bottom Glass Shelf (#09) into place and tighten the set screws. (Fig 7a and Fig 7b) 3 Fig 7a 07 DreamLine. All Rights Reserved 4 Hours Fig 7b Q-Wall Tub manual Ver Rev /07 0

23 Product Maintenance BASES and BACKWALLS: To ensure long-lasting life for your acrylic back walls, wipe them off after each use with a soft cloth. To clean the acrylic back walls use non-abrasive sprays or cream based cleaners. Avoid the use of aerosol spray cleaners. Never use abrasive cleansers, metal brushes or scrapers that could scratch or dull the surface. GLASS: To ensure long-lasting life for your glass shower products, wipe them off after each use with a soft cloth. Rinse and wipe off the glass using either a soft cloth or a squeegee to prevent soap buildup and water spots (Hard water can etch the surface of the glass over time if left to dry). To prevent scratching the surface: never use abrasive cleaners or cleaning products that contain scouring agents. Never use bristle brushes or abrasive sponges that may scratch the surface. HARDWARE: To ensure a long-lasting finish, wipe off the metal parts after each use with a soft cloth. Do not use abrasive cleaners or cleaning products containing ammonia, bleach or acid. If accidentally used, rinse the surface as soon as possible to prevent damage to the finish (peeling or corrosion). After cleaning the polished finishes, rinse thoroughly and wipe dry with a soft cloth. Clean stainless steel surfaces at least once a week. When applying stainless steel cleaner or polish to stainless steel hardware, work with (not across) the grain. Never use an abrasive sponge or cloth, steel wool or wired brush as these may permanently scratch the surfaces. 07 DreamLine. All Rights Reserved NOTE: To maximize the life of your door, it is important to regularly inspect the glass and all hardware for misalignment, proper attachment, and/or damage. Contact DreamLine with any questions or concerns. Q-Wall Tub manual Ver Rev /07

24 TEL: FAX: DREAMLINE.COM For more information on DreamLine Shower Doors and Enclosures please visit DreamLine.com 07 DreamLine. All Rights Reserved

25 VISIONS SHOWER DOOR & TUB DOOR INSTALLATION INSTRUCTIONS IMPORTANT DreamLineTM reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings, manuals or any other details please refer to your model s web page on BathAuthority.com Please read these instructions carefully before installing. If you have any questions regarding installation, please contact our technical support specialists Monday through Friday 8:00 AM 7:00 PM EST at Phone: , Fax: or our technical support group at Support@BathAuthority.com For more information about DreamLineTM Shower Doors & Tub Doors please visit VISIONS Ver Rev 7 07/05

26 Preparation. Prior to installation, examine all boxes and packages for shipping damage and compare the piece count with your packing slip. After opening all boxes and packages read this introduction carefully. Check that all of the needed parts are included in the package by checking off the components on the Detailed Diagram of Shower Door Components. If the unit has been damaged, has a finishing defect, or has missing parts, please contact our customer support department within 3 business days of the delivery date. Please note that DreamLineTM will not replace any damaged products or missing parts free of charge after 3 business days or if the product has been installed. Feel free to contact DreamLineTM if you have any questions, and please provide an order number, job name or other proof of purchase to help us identify your original order.. Please note that you should consult your local building codes with questions about installation compliance standards. Building and plumbing codes may vary by location, and DreamLine is not responsible for code compliance standards for your project. 3. Install all of the required plumbing and drainage before securing the shower. Have a competent and licensed (if required by local code) plumber or tradesman perform and/or approve your plumbing installation. 4. Please make sure that prior to beginning the installation, the surfaces are leveled and solid and will be able to support the total weight of the unit. Also make sure the walls are at right angles. Irregular installation surface level, radius corners or improper angle of side walls will result in serious problems for your installation. Please, note that some adjustments and drilling may be necessary during the installation process. 5. Please protect all primary surfaces of the product during installation. Never set your glass down directly onto a tile floor. Leave corner protectors in place until necessary to remove them. Always use a piece of wood or cardboard to protect the bottom edge and corners of the glass prior to and during installation. 6. This unit must be installed upon a finished threshold and against finished walls. Tools Required Caulk Tape Phillips Measure Pencil Screwdriver Drill bit (Ø=5/6") Drill bit (Ø=/8") Level Caulk Gun Power Hammer Miter saw or Hacksaw Drill VISIONS Ver Rev 7 07/05

27 Detailed Diagram of Shower Door Components Packing List 0 Glass profile pcs 0 Round head screw ST pcs 0 Wall profile pcs Round head screw ST4.x5 8pcs 03 Guide rail pcs Round head screw ST4.x0 4pcs 04 Glass door pcs 3 Flat head screw ST4.x6 4pcs 05 Stationary glass pcs 4 Decorative cover 4pcs 06 Handle pairs 5 Wall anchor 8pcs 07 Magnetic strip pair 6 Glass holder 4pcs 08 Anti-water strip 4pcs 7 Wheel assembly 4pairs 09 Single side strip pcs NOTE: Unpack your unit carefully and inspect it. Lay it out and identify all parts using parts diagram and part list in your manual as a reference. Before discarding the carton, check for small hardware bags that tend to fall to the bottom of the box. If any parts are damaged or missing, please contact DreamLine TM for replacement. VISIONS Ver Rev 7 07/05 3

28 . Measure the distance between the two finished walls at the top, middle and bottom. This distance is marked as W. Also check the threshold for level and the walls for plumb. Shower Door Installation See Fig. for details. W Fig.. Your Guide rails (#03) have been precut for the model width of: 60. (the rails are shorter than the model width by design). If W is less than 60" (W<60 ), then you will need to cut the Guide rails (#03) equally from both ends. Model Width-Finished opening W = L The length to cut off will be "L". In order to keep the pre-drilled center stopper holes centered, it is necessary to cut the top and bottom guide rails equally from both ends. Take L and divide by and cut off equally from each end. L L L Example: 60"(model) -58" opening = " " divide by = " (cut from each end) See Fig. & Fig. 3 for details. Fig. VISIONS Ver Rev 7 07/05 4

29 Fig Once the Guide rails (#03) have been cut, you will need to reinstall the roller stoppers on each Guide rail (#03) on both ends. It is important that these stoppers are installed at the correct location. Remove the existing stopper. Mark the drilling hole at a distance of from the cut off end of the Guide rail (#03). Drill a new hole using an Ø /8 drill bit; then re-attach the stopper with the screw. ATTENTION: Do not drill all the way through the Guide rail, only drill into the first layer. See Fig. 4 for details Ø/8 Fig. 4 VISIONS Ver Rev 7 07/05 5

30 4. Fasten the bottom Guide rail (#03) to the Glass profiles (#0) with the Round head screws ST4.x5 (#). See Fig. 5 for details. TIP: For ease of assembly, add some liquid soap or wax to lubricate the screws prior to attaching the glass profiles to the guide rails. Also, use a low setting on your power drill to prevent stripping the screws during assembly. Fig Slide both pieces of Stationary glass (#05) fully into the grooves of the Glass profiles (#0), and then secure them using the Glass holders (#6) to the bottom Guide rail (#03) using the ST4. x 6 FH screws (#3). It may be necessary to drill an Ø /8 hole in the rails to attach the Glass holders (#6). Mark the holes and remove the glass to drill these holes to prevent damaging or breaking the glass while drilling. See Fig. 6 for details. 3 Fig. 6 VISIONS Ver Rev 7 07/05 6

31 6. Install the Single side strips (#09) in-between the Stationary glass (#05) and the Glass profiles (#0). The strips should be inserted on the side that is facing the inside of the shower. (See detail in Fig. 7) ATTENTION: Do not use a screwdriver or other metal objects to install the Single Side Strip; you can scratch or damage the glass and aluminum. inside 7. Repeat Step #4 and Step #5 to fasten the upper Guide rail (#03) to the Glass profiles (#0) and secure the Stationary glass (#05) with the Glass holders (#6). See Fig. 7 for details. Fig Slide the Wall profiles (#0) all the way into the Glass profiles (#0) on both sides. Make sure the flanges of the Wall profiles (#0) face inside the shower. See Fig. 8 for details. Fig. 8 VISIONS Ver Rev 7 07/05 7

32 9. Move the finished frame to the designated position on the shower base, the bathtub or the threshold (depending on your installation); push it against the walls. If your top and bottom wall opening measurements vary or if the walls are out-of-plumb, make adjustments by sliding the Wall profiles (#0) out of the Glass Profiles (#0). Use a level to adjust the frame so that it is plumb. See Fig. 9 for details. Fig Using help to hold this assembly in the right position, mark the drill holes on the wall through the holes on the flange of the Wall Profiles (#0). 4. Gently set the assembled unit aside; drill the holes using a Ø 5/6 drill bit and insert the Wall anchors (#5). Apply silicone caulk along the Wall profiles (#0) and around the holes on the wall. Also apply silicone under the bottom Guide rail (#03). Place the whole shower assembly back into the designated position and secure it to the walls using the Round head screws ST4. 30 (#0). Ø5/6 5 See Fig. 0 for details. 3 6 Fig. 0 VISIONS Ver Rev 7 07/05 8

33 . Fasten the top and the bottom Wheel assemblies (#7) to the Glass doors (#04). The top wheels can adjust the door level with the adjustable bolt and lock nut. The bottom wheel has a press button to fix the wheel on to the bottom Guide rail (#03). 4 Note: The lock nut of the upper wheel and the press button of the bottom wheel should be pointing up. (Fig. and.) 5 See Fig. for details. 3 6 Fig. 3. Slide the top door wheels into the top Guide rail (#03). Push the bottom wheels into the bottom Guide rail (#03) by pressing down on the button on the Wheel assembly. (Fig.) Use a Phillips screwdriver # to adjust the upper wheels to make sure they track smoothly and the door closes tight. (do not use a power screwdriver to avoid damaging the assembly) 3 4 See Fig. for details. Fig. VISIONS Ver Rev 7 07/05 9

34 4. Install the Handles (#06) to the Glass doors (#04).(Fig 3.) Press the anti-water strips (#08) onto the vertical edges of the Stationary glass (#05) and both vertical edges of the Glass doors (#04). Press the Magnetic strips (#07) onto the vertical edges of both Glass doors (#04) for a tight seal. See Fig. 3 for details. 3 Fig Do the final adjustments of the assembled unit in the Wall profiles (#0). Make sure that the bottom rail is tight to the the threshold. Drill the holes in the Glass profile (#0) through predrilled holes in the Wall Profile (#0) using Ø /8 drill bit. ATTENTION: Do not drill the profile throughout, only the first layer of the wall profile. Ø/8 Secure the Wall profile (#0) to the Glass profile (#0) using the Round head screws ST4. 0 (#). Cover the exposed screw heads with the Decorative covers (#4). See Fig. 4 for details. 3 Fig. 4 VISIONS Ver Rev 7 07/05 0

35 6. Apply a good quality mildew resistant silicone along the profiles and guide rails; on the seams between the bottom guide rail and the profiles as well as along the shower base or threshold. See Fig. 5 for details. Caulk Fig. 5 Product Maintenance BASES and BACKWALLS: To ensure a long life for your acrylic back walls: wipe them off after each use with a soft cloth. To clean the acrylic back walls use non-abrasive sprays or cream based cleaners. Never use abrasive cleansers, metal brushes or scrapers that could scratch or dull the surface. GLASS: To ensure long lasting life for your glass shower products: wipe them off after each use with a soft cloth. Rinse and wipe off the glass using either a soft cloth or a squeegee to prevent soap buildup and water spots. To prevent scratching the surface: never use abrasive cleaners and cleaning products that contain scouring agents. Never use bristle brushes or abrasive sponges. HARDWARE: To ensure a long lasting finish: wipe off the metal parts after each use with a soft cloth. Do not use abrasive cleaners or cleaning products containing ammonia, bleach or acid. If accidentally used, rinse the surface as soon as possible to prevent finish peeling or corrosion. After cleaning the shiny finishes, rinse thoroughly and wipe dry with soft cloth. Clean stainless steel surfaces at least once a week. When applying stainless steel cleaner or polish, work with (not across) the grain. Never use abrasive sponge or cloth, steel wool or wired brushes. VISIONS Ver Rev 7 07/05

36 TEL: FAX: For more information on DreamLine TM Shower Doors & Tub Doors please visit VISIONS Ver Rev 7 07/05