Assembly Instructions

Size: px
Start display at page:

Download "Assembly Instructions"

Transcription

1 RoomScape Furniture System March 2013

2 - Bed Styles bed deck board bed deck board top cap top cap base glide middle side rail frame frame stacking device frame middle lower reinforcement side rail Single Bed base glide Loft Bed top cap frame stacking device bed deck board base glide frame side rail middle Bunk Bed 2

3 Figure 1 frame mounting slot frame assembly top cap frame stacking device frame base glide side rail interlock bracket End Frame Assembly Loft and bunk bed assemblies require a pair of frames at each of the assembly. The pair of frames must be connected with two stacking devices. Base glides (with hole in center) must be attached at bottom where frames meet floor. Place top caps (solid) on upper openings of frames (Figure 1). Single bed assemblies require one frame at each with top caps and base glides (with hole in center) installed as described. Side Rail & Lower Reinforcement Assembly for Loft Beds (For Loft Beds with Megasurface see Page 5) Holding one of frame assembly, attach one side rail to frame by sliding interlock bracket (with hooks downward) into mounting slot in frame. Press down to secure. Repeat procedure with frame at other of assembly. Install the second side rail in the same way making sure both rails are at the same height. Install the lower reinforcement in the same way, near the floor with finished side facing inward (Figure 2). Lower reinforcement is not required for bunk bed installations. For bunk beds, install lower side rails same as above. lower reinforcement Figure 2 3

4 End & Middle Stringer Assembly Slide tongues of and middle s into belt loops on inside of side rails. End s must be positioned so that higher vertical edge faces out at front and back of bed assembly (Figure 3). middle tongue side rail belt loop Bed Deck Assembly Bed deck requires that three deck boards be set in place between side rails and be supported by middle and s. Slide in outside boards first, followed by center bed deck board (Figure 4). Figure 3 bed deck board (center) bed deck board (outside) middle Figure 4 4

5 Figure 5 piano hinge #8x1" Figure 6 #10x1" PowerUp module thumb drop-leaf surface splice plate thumb s worksurface support bracket (left) drop-leaf arm megasurface (left) mega tackboard worksurface support bracket (right) 3 #8-32 x/ 8 megasurface (right) #10x1" side rail thumb anchor bracket top cap hang-on worksurface frame stacking device frame base glide Hang-On Megasurface 1. Assemble two sets of frames as described on page Stand up both frame sets and hang the mega tackboard between them (Figure 5). The mega tackboard has teeth spaced 2 apart so that they can fit around the stacking device collar. 3. Hang one of a side rail into one of the frames at the desired height. Apply outward pressure to the frames to force them apart. The other of the side rail can now be inserted into the opposite frame. Repeat this procedure for the second side rail. 4. Hang one right and one left worksurface support bracket on the frames opposite the mega tackboard. Make sure the top of the brackets are at the same height as the flange of the mega tackbaord (Figure 5). 5. Place the megasurface halves on top of the appropriate right and left worksurface support brackets and flange of the mega tackboard. Fasten the worksurface halves to the support brackets and flange with eight thumb s (Figure 5). 6. Join the worksurface halves with one splice plate and four thumb s. 7. Route the power cord of the power & data module (optional) down through the hole in the worksurface. Snap the module into place and check for proper operation. 8. See page 4 for and bed deck assembly. Drop-Leaf Surface 1. Position both the drop-leaf surface and the hang-on worksurface face down on a soft protective surface. The worksurface edges should be touching and the front and rear edges of both should be flush. 2. Center the piano hinge over the seam where the worksurfaces meet. Using the hinge as a template, mark the holes onto both worksurfaces. Remove the hinge and drill 1 / 8 diameter pilot holes. Take care not to drill too deep, piercing through the surface. Keeping the two worksurfaces together, attach the piano hinge to both with twenty-four #8 x 1 s (Figure 6). 3. Position the anchor bracket on the center of the hang-on worksurface, 2 back from the seam of the two surfaces. Mark the nine holes through the bracket and carefully drill 1 / 8 diameter pilot holes. Attach the bracket to the hang-on worksurface with nine #10 x 1 s (Figure 6). 4. Secure the drop leaf arm to the anchor bracket as illustrated with two #8-32 x 3 / 8 s (Figure 6). 5. With the drop-leaf arm fully exted, rotate it onto the drop-leaf surface. Apply downward pressure to the arm and mark the mounting holes on the surface. Carefully drill 1 / 8 diameter pilot holes. Secure the arm to the drop-leaf surface with two #10 x 1 s. When installing the arm, make sure that enough support is supplied by the arm to keep the drop-leaf surface from sagging (Figure 6). 6. Carefully follow instructions on page 6 to install the hang-on worksurface to the bed frame. 5

6 - Optional Accessories Optional Accessories- Bed Safety Bar 1. Install prior to placing the deck boards into the bed deck assembly (Figure 7). 2. Place the safety rail so that the top lip of the channel goes over the top edge of the side rail (Figure 7). 3. Rotate the safety rail so that its bottom lip is positioned below the bed rail, on the inside of the bed frame (Figure 7). 4. Install the bed deck boards. The deck board will trap the safety rail and keep it from rotating out of position. Hang-On Shelf, Hang-On Flipper Door Unit, Hang-On Coat Rack, Hang-On Dresser 1. Hook the shelf/flipper door into the slots in the bed frame above the worksurface or any other location desired. Mount both sides of the shelf/flipper door at the same time. Press down to secure (Figure 7). Ladder for Bunk Beds 1. Slide ladder through ladder hook, and place the ladder vertically against the upper bed rail (Figure 7). 2. Slide hook over the top of the upper bed rail and tighten hand (Figure 7). 6 Note: The ladder is designed to be vertical, not angled to the bed. Do not angle the bottom of the ladder away from the bed as this will create stress on the ladder hook bracket. Ladder for Loft Beds 1. Begin installation by leaning the ladder against the upper bunk of loft side rail at the location where it is to be installed. Position the ladder hook over the ladder as illustrated. Slide the ladder hook onto the ladder and hook the back tab of the ladder hook onto the bed rail. Do not secure ladder hook to ladder or side rail at this time (Figure 8). 2. For loft beds, a bottom bracket must be installed as illustrated. Capture the lower of the ladder leg with the bracket and hook the teeth of the bracket into the slot in the frame close to the floor. Press down to secure bracket to frame. Using a power driver route two #10 x 3 / 4 Torx head self-drilling s through the two mounting holes and bore them into the ladder (Figure 8). 3. Using a power driver and two #10 x 3 / 4 Torx head self-drilling s, secure the back tab of the ladder hook to the interior of the side rail through the pre-drilled mounting holes in the back tab (Figure 8). 4. Lastly, secure the upper ladder hook to the ladder by using a power driver and two #10 x 1 Torx head self-drilling s. Route the s through the mounting holes on each side of ladder hook and bore the s into the ladder (Figure 8). Drafting Board 1. Drafting board can be placed on any worksurface (Figure 7). Task Light 1. See instructions on page 8. Cord Management 1. Hook the cord manager into the slots below the task light and/ or any place electrical cords are present (Figure 7). 2. Hide the cords by pushing them into the open edge of the cord manager (Figure 7). Hang-On Worksurface 1. Hang one right and one left cantilever bracket at the same height on a bed frame. Hold bracket at an angle to the bed frame to hook top locking tab in. Rotate down and hook tabs into slots. Press down to secure (Figure 8). 2. Place the worksurface on top of the cantilever brackets and attach with four thumb s (Figure 8). Figure 7 Figure 8 ladder hook ladder bed safety bar #10x1 torx head self drilling rail side 3 #10 x/ 4 torx head self drilling ladder lower reinforcement hand bottom bracket (loft beds only) Sliding Keyboard Tray 1. See instructions on page #10 x/ 4 torx head self drilling drafting board ladder hook hang-on shelf unit task light cord manager RoomScape frame hang-on worksurface cantilever bracket sliding keyboard tray

7 - Optional Accessories tackboard center drawer pedestal top hang-on coat rack free standing dresser top Free Standing Dresser Top and Free Standing Pedestal Top 1. Remove backing from two-way tape located on bottom surface of top. 2. Position top over cabinet, align edges, and press into place (Figure 9). Tackboard 1. Hook the tackboard into the slots in the bed frame above the worksurface or any other desired location. Hang both sides of the tackbaord brackets at the same time. Press down to secure (Figure 9). Figure 9 Center Drawer 1. See instructions on page 8. stack-on wardrobe personal shelf Personal Shelf 1. The personal shelf can be hung along the bed rail where desired (Figure 10). Hang-On Megasurface 1. See instructions on page 5. CPU Sling 1. See instructions on page 9 and 10. free-standing wardrobe Figure 10 hang-on flipper door unit hang-on megasurface CPU sling hang-on dresser Free-Standing Wardrobe 1. Can be positioned up against either frame, or at any desired location in room (Figure 10). Stack-On Wardrobe 1. Position onto free-standing wardrobe, lining up clearance holes of free-standing wardrobe with weldnut holes in bottom of stack-on wardrobe (Figure 10). 2. Fasten the two units together with four thumb s from inside free-standing wardrobe. 7

8 Center Drawer Assembly 1. Begin installation of the center drawer by making sure the glides on each side of the drawer are snapped in the closed position. Find and remove the hardware pack which is taped to the inside of the drawer. mounting bracket worksurface front edge 2. Position the drawer unit under the worksurface at the desired location, with the front edge of the drawer being flush with the front edge of the worksurface. Using a pencil, mark the worksurface at the center slots of the four mounting brackets (Figure 11). drawer glide 3. Drill four pilot holes not more than 1 / 2 deep using a 1 / 16 drill bit at the locations marked for mounting the drawer to the underside of the worksurface (Figure 11). 4. Position the center drawer over the pilot holes in the worksurface and secure with four #8 x 1 / 2 Phillips s (Figure 11). Figure 11 center drawer assembly 1 #8 x/" 2 Phillips Task Light 1. Carefully remove task light and brackets from carton. 2. Assemble task light and brackets by sliding brackets through the belt loops at each of the task light (Figure 12). 3. Locate front of task light brackets inside front lip of overhead shelf bottom (Figure 13). 4. Flex rear of task light brackets outward until brackets will pass over rear lip of shelf bottom and slide in place (Figure 14). 5. Route power cord out of sight to a 115 volt grounded outlet. See page 6 and Figure 7 for Cord Management option. 8 belt loop task light task light bracket bracket Figure 12 Figure 13 Figure 14 overhead shelf bottom task light front

9 buckle clip slot "D" CPU Sling Assembly 1. Lay the CPU holder and strap bracket out as illustrated in Figure 15. First route the of the sling strap through slot A and slot B in the strap bracket, and pull buckle to within a few inches of slot A. Next route the strap through slots C and D in the CPU holder as shown. Finally, following the arrow, route the strap through the buckle clip. Follow the above procedure for the other sling strap (Figure 15). 3 #8 x/" 8 slot "C" slot "A" slot "B" 2. Secure the handle to the CPU holder with two #8 x 3 / 8 s at the two holes located above the vinyl feet (Figure 15). handle vinyl feet CPU holder Figure 15 strap buckle sling strap strap bracket 3. To mount the CPU to the CPU holder, first set the CPU onto the straps and strap bracket as shown. Position the CPU holder onto the top of the CPU with the vinyl feet resting against the top of the CPU. The front vinyl feet (at handle ) must set just behind the font bezel on the CPU (Figure 16). 4. Be sure the straps are wrapped around the CPU as illustrated. Snap the buckle together. Hold the CPU securely and pull up forcefully on the strap s to tighten. The straps must be pulled tight to secure, and periodic re-tightening may be required (Figure 16). 5. Determine the correct location to mount the track under the worksurface. The track must be positioned square to the front edge of the worksurface and set back from the front edge to obtain a desirable retraction position for your CPU. Use the track as a template and mark all eight of the hole locations on the underside of the worksurface (Figure 16). 9

10 6. Using a power drill and a 1 / 8 drill bit, drill eight pilot holes, 5 / 8 deep in the underside of the worksurface. Do not drill deeper than 5 / 8 to avoid piercing the top of the worksurface. 7. Mount the track to the underside of the worksurface at the six outside mounting holes using the #8 x 5 / 8 s provided. Press a rubber bumper onto a #8 x 5 / 8 and install bumper into the rear, center hole in track. Make sure all s are tight (Figure 16). 8. Slide the assembled unit and CPU into the groves on the track until it stops at the rear rubber bumper. Press a rubber bumper onto the remaining #8 x 5 / 8 and install the bumper and into the front, center hole in the track (Figure 16). CPU front bezel handle CPU holder front edge of worksurface track rubber bumper (front) rubber bumper (rear) 5 #8 x /" 8 5 #8 x /" 8 9. Position the cap (track guard) in front of the track at the underside of worksurface. Mark the two mounting hole locations (Figure 16). vinyl feet 10. Using a power drill and a 1 / 8 drill bit, drill the two pilot holes 5 / 8 deep in the underside of the worksurface. Do not drill deeper than 5 / 8 deep to avoid piercing the top of the worksurface. buckles strap bracket cap (track guard) 5 #8 x /" Mount the cap (track guard) to the underside of the worksurface with two #8 x 5 / 8 s (Figure 16). Figure 16 10

11 keyboard tray Figure 17 nut lock washer angle bracket tapping extension slide machine Sliding Keyboard Tray Assembly 1. Remove all parts from box: Parts include : One plastic keyboard tray Two extension slides Four angle brackets Four #10-32 x 3 / 8 binding head Phillips machine Four #10-32 hex nuts Four #10 lock washers Four #8 x 3 / 8 truss head Phillips tapping s 2. Place keyboard tray face down on table surface. 3. Position extension slides so that tabs with slots are placed into cutouts on lower edge of keyboard tray (Figure 17). 4. Put tapping s through slots in extension slide tabs and into holes in keyboard tray. Do not tighten (Figure 17). 5. Press extension slide firmly against side of keyboard tray and tighten tapping s (Figure 17). 6. Repeat for other extension slide. 7. Select position for angle bracket and place in position against extension slide. When using the hole shown in the diagram, there will be approximately 3 3 / 4 clearance from the bottom of the table/ desk surface to the surface that the keyboard rest on. The keyboard surface may be moved 1 / 2 or 1 closer by using one of the other two available holes (Figure 17). 8. Insert machine through hole in angle bracket and bracket on extension slide. Slide lock washer over machine. Turn nut onto machine and tighten (Figure 17). Repeat for other three brackets. 9. Determine the location of the tray assembly to be installed. 10. Drill corresponding pilot holes to the pattern formed by the bracket slots (Figure 18). 11. Attach the tray assembly by holding it up to the bottom surface of the table/desk top and inserting s (not included) into the top (Figure 18). 12. It is recommed that at least four s (one for each angle bracket) be installed to adequately secure tray assembly to table/desk surface (Figure 18). Figure 18 11

12 KI 1330 Bellevue Street P.O. Box 8100 Green Bay, Wisconsin Ki is a registered trademark of Krueger International, Inc KI All Rights Reserved Litho in USA. Code KI-60343R2/KI/GT/0313

Assembly Instructions

Assembly Instructions InTandem Table System November 20 InTandem Table System - Worksurface #4 x/" 4 wood screw power beam Tools Provided T-0 Extended Torx Driver T-25 Torx Driver Additional Tools Required Soft protective

More information

Revised

Revised Indentify Non-powered panels and separate from Powered panels. Non-powered panel shown at left.. Powered panel shown at left has powerway mounted at factory. Also separate panels by surface type, width

More information

Workbench Instructions for Assembly

Workbench Instructions for Assembly Workbench Instructions for Assembly Technical Electronic Workstations and Industrial Workbenches Includes: Cabinets Privacy Panels Stringers Bottom Shelves Table of Contents Tools Required for Assembly...

More information

Product must be installed as shown using the screws and brackets provided. Use of incorrect hardware could result in damage to the product.

Product must be installed as shown using the screws and brackets provided. Use of incorrect hardware could result in damage to the product. General Notes These installation instructions are intended to be comprehensive for a typical Keyeira/Presto configuration. Your configuration may differ. If you have questions contact Geiger Customer Service

More information

compile system INSTALLATION GUIDE Updated January 2019

compile system INSTALLATION GUIDE Updated January 2019 INSTALLATION GUIDE Updated January 09 compile system Table of Contents Panels 0 Quick Connect Clips 0 Lock Clips 0 Panel Trims 0 Privacy Glass 0 Post Base Covers 04 Electrical 04 Power Distribution Harness

More information

Assembly Instructions

Assembly Instructions Unite Panel System Hinge Door July 2016 #12 x / slotted hex washer head bolt Figure 1 threshold bracket frame Detail F threshold bracket threshold bracket (installed) #12 x / slotted hex washer head bolt

More information

Workbench Instructions for Assembly

Workbench Instructions for Assembly Workbench Instructions for Assembly FlexWorks is a trademark of Lista International Corporation. Making Workspace Work is a trademark of Lista International Corporation. Document Number: MD002A3 Print

More information

LAN Locker Adjustable Shelves

LAN Locker Adjustable Shelves Adjustable Shelves LAN LOCKER ADJUSTABLE SHELVES * Adjustable Shelves are available for LAN LOCKER widths: 24, 30, 48, 60, and 72. * When installing more than one Adjustable Shelf, it is recommended that

More information

Laminate Cabinet Installation Instructions

Laminate Cabinet Installation Instructions Laminate Cabinet Installation Instructions www.easygaragestorage.com/installation How To Use These Instructions Thank you for your purchase! Please read each step of this manual thoroughly to ensure proper

More information

ZAPF PANEL SYSTEM ASSEMBLY INSTRUCTIONS. It is recommended that the components be installed in the sequence of this assembly manual.

ZAPF PANEL SYSTEM ASSEMBLY INSTRUCTIONS. It is recommended that the components be installed in the sequence of this assembly manual. ZAPF PANEL SYSTEM It is recommended that the components be installed in the sequence of this assembly manual. ASSEMBLY INSTRUCTIONS OFFICE FURNITURE FOR THE INFORMATION AGE Table of Contents INSTALLATION

More information

Installation Instructions

Installation Instructions by Plato Woodwork Installation Instructions Plato Woodwork, Inc. 200 Third Street SW P.O. Box 98 Plato, MN 55370 www.platowoodwork.com 800.328.5924 SECTION GUIDE GETTING STARTED PAGE # Installation Methods...

More information

MANUAL e130. Wallstation

MANUAL e130. Wallstation MANUAL 07.29.13 e130 Wallstation The Enovate Medical e130 Wallstation was designed to set a new standard in quality. Enovate Medical s goal is to provide a wallstation that is ready for years of use,

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS SOLID PHENOLIC TOILET PARTITIONS 1080 DuraLineSeries Class-A Fire Rated Includes Institutional Hardware Option.67 IMPORTANT: Storage and Handling Information on last page. Review

More information

C-Series & S-Series Classic Frame with Transom (Single or Pair)

C-Series & S-Series Classic Frame with Transom (Single or Pair) 1. TOOLS REQUIRED Tape measure 6' magnetic level 3' magnetic level Safety Glasses Screw gun #2 Screwdriver tip #3 Screwdriver tip Philips Head screwdriver (Used to move frame on wall using oval slots on

More information

OXYGEN INSTALLATION. Revision date

OXYGEN INSTALLATION. Revision date 12345 1 Hardware List 12345 Flat head wood screw #9 x 7/8 long with #2 Phillips drive, silver Used to attach surfaces and end panels Hex set screw ½-13 x 2 long with 1/4 hex drive, black Used on Legs Hex

More information

a.k.a. casegoods instructions

a.k.a. casegoods instructions a.k.a. casegoods instructions a a.k.a. workwall installation IMPORTANT NOTES Failure to install product according to installation instruction will result in loss of warranty. Tools required for assembly

More information

How To Measure Your Finished Opening

How To Measure Your Finished Opening 3000 Series Bifold Doors How To Measure Your Finished Opening MEASURE FROM RIGHT TO LEFT 2 PLACES (WIDTH) MEASURE FROM TOP TO BOTTOM 2 PLACES (HEIGHT) Tools Required for Assembly: Tools Needed: Phillips

More information

Interra Installation Manual

Interra Installation Manual Interra Installation Manual Instructions to install the Friant Interra panel system Friant & Associates, LLC Table of Contents Getting Started Introduction... 3 General Tools, Staging & Safety... 4 Before

More information

Preference Collection and Treatment Console INSTALLATION GUIDE

Preference Collection and Treatment Console INSTALLATION GUIDE Preference Collection 5580.69 and 5580.96 Treatment Console INSTALLATION GUIDE WARNING Failure to install the 5580 as described in this installation guide may cause the unit to collapse, resulting in serious

More information

P.O. Box 8400 Green Bay, WI (920)

P.O. Box 8400 Green Bay, WI (920) P.O. Box 8400 Green Bay, WI 54308-8400 (920) 468-2165 Change Notice No. 112 Implemented By: KI-Pembroke Notification By: Scott Vissers Date: 03/15/10 Component Product Title: Series XXI Lateral Filing

More information

Right. Side Tower-Overhead Combination Revised 11/12/05 ON SITE A,B D,E C

Right. Side Tower-Overhead Combination Revised 11/12/05 ON SITE A,B D,E C Right ON SITE Side Tower-Overhead Combination Revised 11/12/05 2 Installation of Side Tower-Overhead Combination units is easy when the correct SEQUENCE is followed. 3 Your unit consists of the following

More information

Linear Hook- on Worksurfaces

Linear Hook- on Worksurfaces Linear Hook- on Worksurfaces Linear Hook-On Worksurfaces come in three depths and seven lengths. Different worksurfaces have different reqirements for installation that are outlined below. 27 inch deep

More information

STAKS. Crossover Casegoods ASSEMBLY INSTRUCTIONS

STAKS. Crossover Casegoods ASSEMBLY INSTRUCTIONS STAKS Crossover Casegoods ASSEMBLY INSTRUCTIONS Installation Sequence 1. Wall Panels a. Connector Kit Part Identification 3 b. T - 3 Panel Connection Preparation 4 c. X Panel Connection Preparation 5 d.

More information

Stuff-Your-Stuff Platform Bed (Twin and Full)

Stuff-Your-Stuff Platform Bed (Twin and Full) Stuff-Your-Stuff Platform Bed (Twin and Full) Pre-Assembly: Please read all instructions before beginning assembly. Assembly by two people is a must. Save all packing materials until assembly is complete

More information

Oxford Stalls Installation Instructions

Oxford Stalls Installation Instructions Oxford Stalls Installation Instructions RAMM Horse Fencing and Stalls 13150 Airport Hwy. Swanton, OH 43558-9615 1-800-434-8456 Rev. 8/15/17 Before You Start Typical stall sizes are 10 x 10, 12 x 12 or

More information

CABINETRY Assembly Instructions

CABINETRY  Assembly Instructions www.hdicabinetry.com Assembly Instructions TABLE OF CONTENTS Category Page(s) Section 1: Framed Series Base Cabinet Instructions Wall Cabinet Instructions Easy Reach Cabinet Instructions 1.01-1.04 1.05-1.06

More information

TIP FOR GETTING STARTED

TIP FOR GETTING STARTED Tip for getting started TIP FOR GETTING STARTED Be careful not to drill into any electrical wires, ductwork, plumbing or other damagable components. If you have any questions on the locations of these

More information

Perks Assembly Instructions

Perks Assembly Instructions Perks 2066779 Revision A-10 Complete Series Master Packet 2008 Kimball International, Inc. T 800.482.1818 F 812.482.8300 Perks Page 1 of 1 Mobile Screens Starter Screen Hex Head Wrench Rubber Mallet Package

More information

Preference Collection 5580 Treatment Console INSTALLATION GUIDE

Preference Collection 5580 Treatment Console INSTALLATION GUIDE Preference Collection 5580 Treatment Console INSTALLATION GUIDE 0 WARNING Failure to install the 5580 as described in this installation guide may cause the unit to collapse, resulting in serious injury

More information

Important Loading Information. Tools Required. Meridian Lateral Files Instructions

Important Loading Information. Tools Required. Meridian Lateral Files Instructions Y Meridian Lateral Files Instructions! WARNING Failure to observe stated capacities below will result in unsafe usage conditions, causing possible product damage or personal injury. Important Loading Information

More information

Angled Side Flush with Panel Face

Angled Side Flush with Panel Face Identify and sort panels by like sizes, fabrics, surface type (tackable vs hard), and NON- POWERED vs POW- ERED. Non-powered panels ship without a powerway. Powered panels include a powerway. See below.

More information

ASSEMBLY INSTRUCTIONS TALL CABINET - MODEL CS30

ASSEMBLY INSTRUCTIONS TALL CABINET - MODEL CS30 ASSEMLY INSTRUCTIONS TALL CAINET - MOEL CS30 To avoid SERIOUS INJURY or AMAGE to personal belongings: O NOT overload the cabinet or the shelves, maximum weight limit for feet or caster installation is

More information

METAL BLINDS. Deluxe GETTING STARTED OPTIONAL HARDWARE. A few simple tools are required: STANDARD HARDWARE

METAL BLINDS. Deluxe GETTING STARTED OPTIONAL HARDWARE. A few simple tools are required: STANDARD HARDWARE METAL BLINDS Deluxe GETTING STARTED OPTIONAL HARDWARE A few simple tools are required: Steel Tape Measure Pencil Level Hold Down Brackets with Screws Extension Bracket Power Drill and Drill Bits Flathead

More information

INSTALLATION INSTRUCTIONS for the JOMY RETRACTABLE LADDER. If there are any questions, please call (800)

INSTALLATION INSTRUCTIONS for the JOMY RETRACTABLE LADDER. If there are any questions, please call (800) INSTALLATION INSTRUCTIONS for the JOMY RETRACTABLE LADDER If there are any questions, please call (800) 255-2591 INSTALLATION INSTRUCTIONS WARNING! Ladder Sections Lock When Closed. Do Not Install or Close

More information

Topo Freestanding Applications - Private Office

Topo Freestanding Applications - Private Office 4 3 2 Topo Freestanding Applications - Private Office Combo Wrench If you have a problem, question, or request, call your local dealer, or Coalesse at 1.800.627.6770 Or visit our website: www.coalesse.com

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS HIGH PRESSUE LAMINATE (HPL) TOILET PARTITIONS 1030 TrimLineSeries 1040 DesignerSeries Includes continuous hardware option.65. IMPORTANT: Storage and Handling Information on last

More information

ED1300/1300F SERIES CONCEALED VERTICAL ROD DEVICE INSTALLATION INSTRUCTIONS

ED1300/1300F SERIES CONCEALED VERTICAL ROD DEVICE INSTALLATION INSTRUCTIONS ED1300/1300F SERIES CONCEALED VERTICAL ROD DEVICE INSTALLATION INSTRUCTIONS Ver.2 1300 SERIES CONCEALED VERTICAL ROD DEVICE Top Strike Latch Screws Strike Screws Release Plunger Top Latch Plunger Screws

More information

All Terrain Flares 2014 Chevy Silverado

All Terrain Flares 2014 Chevy Silverado Page 1/8 Components: 1. Front Flares (2) 2. Rear Flares (2) Tools required: - Utility knife - #2 Phillips driver - Socket wrench - 13 mm Socket - 6 mm Allen Wrench - T-15 Torx bit - Trim Removal Tool -

More information

MobileTrak5 Installation Instructions

MobileTrak5 Installation Instructions MobileTrak5 Installation Instructions PLEASE OPEN ALL BOXES & CHECK TO MAKE SURE YOU HAVE ALL PIECES REQUIRED READ ALL INSTRUCTIONS BEFORE STARTING Tools Required for Assembly 7/16, 1/2 Wrench Phillips

More information

D. Drill Bolt Holes Through Topper Shell and Bed Rails

D. Drill Bolt Holes Through Topper Shell and Bed Rails A. Check Mounting Kit Check to make sure that all of the following items are included in the mounting kit. Call 515-272-4372 if you need to obtain a part from BrandFX. Double-stick tape (1 roll) White

More information

Installing Electronic Media Storage Components into Lateral File Cabinets

Installing Electronic Media Storage Components into Lateral File Cabinets Steelcase, Inc. Grand Rapids, MI 49501 U.S.A. 1-888-783-3522 Installing Electronic Media Storage Components into Lateral File Cabinets 830-CH-9 830-CH-12 830-CH15 836-CH-9 836-CH-12 836-CH-15 842-CH-9

More information

AFCO-Rail Post INSTALLATION INSTRUCTIONS AFCO-RAIL POST

AFCO-Rail Post INSTALLATION INSTRUCTIONS AFCO-RAIL POST AFCO-Rail Post INSTALLATION INSTRUCTIONS TOOLS REQUIRED: Drill Bits (for the appropriate fastener) Drill (with adjustable clutch, recommended) Level String Line Tape Measure Tools to install fasteners

More information

This instruction manual is an in-depth look and explanation of how to assemble and install the Murphy Bed properly and efficiently.

This instruction manual is an in-depth look and explanation of how to assemble and install the Murphy Bed properly and efficiently. This instruction manual is an in-depth look and explanation of how to assemble and install the Murphy Bed properly and efficiently. Don t be put off by the size of the instruction manual as the large diagrams

More information

PRE-ENGINEERED HORSE STALL SYSTEMS SDFD SLIDING DOOR c/w FOLD-DOWN GRILL. & Assembly. Installation Instructions

PRE-ENGINEERED HORSE STALL SYSTEMS SDFD SLIDING DOOR c/w FOLD-DOWN GRILL. & Assembly. Installation Instructions PRE-ENGINEERED HORSE STALL SYSTEMS 4800 SDFD SLIDING DOOR c/w FOLD-DOWN GRILL & Assembly Installation Instructions 4800 SDFD Sliding Door c/w Fold-Down Grill Components - 1 3 /4" x 2" x 88" channels (2)

More information

OB1U INSTALLATION INSTRUCTIONS. Interactive Flat Panel Over White Board Mount

OB1U INSTALLATION INSTRUCTIONS. Interactive Flat Panel Over White Board Mount INSTALLATION INSTRUCTIONS Interactive Flat Panel Over White Board Mount Spanish Product Description German Product Description Portuguese Product Description Italian Product Description Dutch Product Description

More information

Copyright Black Box Corporation. All rights reserved Park Drive Lawrence, PA Fax

Copyright Black Box Corporation. All rights reserved Park Drive Lawrence, PA Fax Copyright 2003. Black Box Corporation. All rights reserved. 1000 Park Drive Lawrence, PA 15055-1018 724-746-5500 Fax 724-746-0746 JULY 2003 RM3010A RM315-R2 RM323-R2 RM329 RM451 RM457 RM3020A RM316 RM324-R2

More information

Yes 20 Charging Wall Cabinet for Tablets

Yes 20 Charging Wall Cabinet for Tablets Built with Anthro-DNA Owner's Manual for Yes 20 Charging Wall Cabinet for Tablets Part # YESCABGMPW Components at a Glance 1 2 4 5 8 7 10 3 6 9 Front of Cabinet (closed) 1. Locking front door to User area.

More information

ASSEMBLY INSTRUCTIONS. enook Pro

ASSEMBLY INSTRUCTIONS. enook Pro ASSEMBLY INSTRUCTIONS enook Pro Product enook Pro for Monitors, 36w Part# EPM3616zz/xx Anthro Corporation 10450 SW Manhasset Dr. Tualatin, OR 97062 Toll-free: 800.325.3841 Fax: 800.325.0045 email: sales@anthro.com

More information

Parts List (Continued) 18 each: #8 x 0.625" Truss Head Phillips Screw 20 each: #8 x 1.75" Flat Head Phillips Screw 4 each: #8 x 1.25" Flat Head Philli

Parts List (Continued) 18 each: #8 x 0.625 Truss Head Phillips Screw 20 each: #8 x 1.75 Flat Head Phillips Screw 4 each: #8 x 1.25 Flat Head Philli EVO Tall Pull-Out Wood Pantry Important Notes Always read the instructions completely and carefully before beginning assembly. Remove and check contents for damage and/or missing parts. Keep the original

More information

STANDARD 430E Series. Bottom mounted full extension drawer runners 430E E E E E E E E E4000

STANDARD 430E Series. Bottom mounted full extension drawer runners 430E E E E E E E E E4000 STANDARD 430E Series Bottom mounted full extension drawer runners Specifications Runner 430E8000 430E7500 430E7000 430E6500 430E6000 430E5500 430E5000 430E4500 430E4000 430E3500 430E3000 430E2500 Nominal

More information

Assembly Instructions & General Overview

Assembly Instructions & General Overview Assembly Instructions & General Overview 1. General Overview & Assembly Order...Page 3 2. Assembling the Structural Components Page 4-11 3. Power, Data, Power Poles and Cable Floor Boxes.Page 12-17 4.

More information

VACUSEAL MODEL 200. HOT TUB PRODUCTS 233 Carrington Road Bethany CT

VACUSEAL MODEL 200. HOT TUB PRODUCTS 233 Carrington Road Bethany CT VACUSEAL MODEL 200 J G F G H L HOT TUB PRODUCTS 233 Carrington Road Bethany CT 06524 860-469-2580 www.vacusealcoverlift.com www.hottubproducts.com Made in USA H K E D C I A P B 10 9 8 7 6 5 4 3 2 1 0 SPAS

More information

Versatrac Bypass Door Units, Conventional and Top Track, 300 and 400 Series

Versatrac Bypass Door Units, Conventional and Top Track, 300 and 400 Series Versatrac Bypass Door Units, Conventional and Top Track, 300 and 400 Series TM Rough opening width (finished opening width plus 9/16") Notch for top track units (used as frame header) Rough opening height

More information

Mirage Installation Manual

Mirage Installation Manual Mirage Installation Manual General Information This installation manual provides necessary information for the safe installation of the Mirage product. WARNING: Failure to follow the instructions in this

More information

INSTRUCTION BOOKLET #34. For Wallbed models: KING SIZE SIERRA WITH STORAGE HEADBOARD

INSTRUCTION BOOKLET #34. For Wallbed models: KING SIZE SIERRA WITH STORAGE HEADBOARD For Wallbed models: KING SIZE SIERRA WITH STORAGE HEADBOARD INSTRUCTION BOOKLET #34 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION

More information

Sentinel Series Cigar Humidor End Tables

Sentinel Series Cigar Humidor End Tables Sentinel Series Cigar Humidor End Tables Assembly Instructions Models: Sentinel 500, 1000 and 1500 Style: Contemporary SENTINEL ASSEMBLY INSTRUCTIONS Congratulations! You have purchased a superior cigar

More information

How to Install Custom Real Wood and Faux Wood Blinds

How to Install Custom Real Wood and Faux Wood Blinds Before you begin your installation: READ ALL INSTALLATION INSTRUCTIONS! Make sure that you have all tools and hardware needed for installation. Check the installation surface (wall, ceiling, or window

More information

Footprint Mobile Assembly Instructions

Footprint Mobile Assembly Instructions Footprint Mobile Assembly Instructions 1998754 Revision -1 Complete Series Master Packet If you have any questions concerning these instructions, please call Kimball Office Customer Service. 20 Kimball

More information

Track Rack. * Track Racks are not lockable

Track Rack. * Track Racks are not lockable The Track Rack s unique staggered, sliding hook design creates the greatest parking efficiency while still providing easy access to any particular bike. When adding or removing a bike to the rack, simply

More information

A MULTI-PURPOSE LOFT THAT CAN BE USED FOR SLEEPING, STORAGE, AND FREEING UP SPACE (Supports 200 lbs max) DIFFICULTY: 6/10

A MULTI-PURPOSE LOFT THAT CAN BE USED FOR SLEEPING, STORAGE, AND FREEING UP SPACE (Supports 200 lbs max) DIFFICULTY: 6/10 A MULTI-PURPOSE LOFT THAT CAN BE USED FOR SLEEPING, STORAGE, AND FREEING UP SPACE (Supports 200 lbs max) DIFFICULTY: 6/10 CAUTION The instructions are only a guide, and should be followed by individuals

More information

Range height adjustable assembly

Range height adjustable assembly Table of contents Digital handset operation 3 Height adjustable bench kit 4-5 Cable carrier 6 Ganging tray and ganging rail 7 Height adjustable return frame kit 8 Cable entry pole 9 24 and 30 d worksurfaces

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS SOLID PHENOLIC TOILET PARTITIONS 1080 DuraLine Series 1180 DuraLine Series Class-A Fire Rated IMPORTANT: Review these instructions thoroughly prior to installation. FLOOR ANCHORED

More information

Exponents Bench Cushion

Exponents Bench Cushion Exponents Bench Cushion Power Drill #2 Phillips Bit Bit Holder Page 1 of 2 939500640 Rev A 1. Place cushion on top of the bench, so the black Coalesse tag is in the right rear corner of the bench. 2. From

More information

ROS-APT Caucus Plinth Table with Trough Note: Details apply, however the actual configuration of your table may vary from what is depicted here.

ROS-APT Caucus Plinth Table with Trough Note: Details apply, however the actual configuration of your table may vary from what is depicted here. ROS-APT Caucus Plinth Table with Trough Note: Details apply, however the actual configuration of your table may vary from what is depicted here. Parts List - Tables Tops, Top Insert Panels and Base panels

More information

ADJUST-A-VIEW HALF CIRCLE INSTALLATION INSTRUCTIONS

ADJUST-A-VIEW HALF CIRCLE INSTALLATION INSTRUCTIONS Omega Mfg. Corporation Two Rivers, WI (800) 874-9594 www.adjustaview.com Proudly Serving Customers Since 1976 Page 1 of 7 MATERIAL LIST ADJUST-A-VIEW User Instructions ADJUST-A-VIEW Installation Instructions

More information

TITAN2-EDGE Public Access Computer Station Dual Track

TITAN2-EDGE Public Access Computer Station Dual Track TITAN2-EDGE Public Access Computer Station Dual Track TITAN2-EDGE Rev A 6/17 Model TITAN2-EDGE ASSEMBLY AND ADJUSTMENT TITAN2-EDGE PARTS AND TOOLS PLEASE REVIEW these instructions before beginning the

More information

Assembly Instructions

Assembly Instructions 10' and 12' Octagon Cedar Gazebo Assembly Instructions Toll Free: 866.768.8465 Hours: 9-5 Monday-Friday EST www.homeplacestructures.com Package ships as shown revised 06/20/09 Cedar Gazebo Assembly Instructions

More information

Installation Instructions

Installation Instructions Installation Instructions For Models: Model Number / Description File Name 1540 Classic Series P-Lam Toilet Partitions 1540.pdf 1 INSTALLATION INSTRUCTIONS LAMINATED PLASTIC TOILET PARTITIONS 1540 Classic

More information

Side Mount INSTRUCTION BOOKLET #C122 BED STYLE: PARK CITY

Side Mount INSTRUCTION BOOKLET #C122 BED STYLE: PARK CITY Side Mount BED STYLE: PARK CITY INSTRUCTION BOOKLET #C1 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION PROCESS COULD RESULT

More information

NEXUS SERIES CABINETS

NEXUS SERIES CABINETS NEXUS SERIES CABINETS STANDARD BASE ASSEMBLY INSTRUCTIONS Also applies to: Galaxy Series, Nexus Series, Ridgeline Series, Statesman Series, and Waterford Series FOR YOUR INFORMATION: These assembly instructions

More information

HOUSE PARTS PACKED IN HOUSE BOX PARTS IN PLASTIC BAG (HARDWARE) PARTS IN SMALL PLASTIC BAG (FLOOR CLIPS) PARTS PACKED IN BUNDLE

HOUSE PARTS PACKED IN HOUSE BOX PARTS IN PLASTIC BAG (HARDWARE) PARTS IN SMALL PLASTIC BAG (FLOOR CLIPS) PARTS PACKED IN BUNDLE Check parts against this list before starting assembly. Refer to illustrations on pages 6 and 7 to view house parts. If any shortages are found, refer to Packing Slip for claim instructions. Item 3 5 6

More information

ASSEMBLY INSTRUCTIONS DIY WALL BED KIT QUEEN BI FOLD DOOR CABINET & MECHANISM. Tools Required For Assembly. 6.5mm Masonry Drill Bit

ASSEMBLY INSTRUCTIONS DIY WALL BED KIT QUEEN BI FOLD DOOR CABINET & MECHANISM. Tools Required For Assembly. 6.5mm Masonry Drill Bit ASSEMBLY INSTRUCTIONS DIY WALL BED KIT QUEEN BI FOLD DOOR CABINET & MECHANISM Tools Required For Assembly No 2 & No 4 Phillips Head Screwdrivers No 2 Slot Head Screwdriver Hammer Electric Drill (Hammer

More information

INSTRUCTION BOOKLET #C20

INSTRUCTION BOOKLET #C20 INSTRUCTION BOOKLET #C0 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION PROCESS COULD RESULT IN SEVERE PERSONAL INJURY TO

More information

FLEXCELL HONEYCOMB BLINDS

FLEXCELL HONEYCOMB BLINDS FLEXCELL HONEYCOMB BLINDS GETTING STARTED BRACKET INFORMATION A few simple tools are required: The brackets you received with your product are REQUIRED for proper installation. s should be installed at

More information

CROWN IMPERIAL ASSEMBLY INSTRUCTIONS

CROWN IMPERIAL ASSEMBLY INSTRUCTIONS CROWN IMPERIAL ASSEMBLY INSTRUCTIONS Standard Drawer Box Page 1 of 14 Standard Drawer Box Parts Parts Supplied B C D A E F G Page 2 of 14 Part Letter Part Name Quantity 300-600 Deep Pan A Base Panel 1

More information

Deck Mount Installation with Bench

Deck Mount Installation with Bench Deck Mount Installation with Bench 1. Mark track with square. 2. Cut tracks with saw. 3. Drill ¼ hole (if needed.) 4. Countersink track. 5. Countersink all track 6. File all track ends. ends. 7. Lay out

More information

FitWork Walkstation Series 7 AdjusTables

FitWork Walkstation Series 7 AdjusTables FitWork Walkstation Tools Required: #2 Phillips Bit with Extension Page 1 of 20 A7TG660606H A7TR663232H FitWork Walkstation 4mm Hex Head Bit A7TG660632H A7TR383030H www.details-worktools.com A7TG663206H

More information

GlideRite Retractable Cover System For HotSpring & Tiger River Spas (except Classic & pre-2000 Landmark Spas)

GlideRite Retractable Cover System For HotSpring & Tiger River Spas (except Classic & pre-2000 Landmark Spas) List of Contents Quantity Description 12 #10 x 1 ½ Flat Head Phillips Screw (see pg. 2) 2 #10 x ½ Pan Head Phillips Screw (see pg. 2) 8 ¼ x 2 ½ Lag Bolt (see pg. 2) 7 ¼ 20 x 5 / 8 Hex Head Bolt (see pg.

More information

INSTRUCTION BOOKLET #C10 Watch step by step installation instructions at: https://www.wallbedsbywilding.com/wallbed-installation-studio-series/ WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY.

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS COMPACT LAMINATE TOILET PARTITIONS 1080 DuraLineSeries 1180 DuraLineSeries Class-A Fire Rated Includes Institutional Hardware Option.67 IMPORTANT: Storage and Handling Information

More information

IMPORTANT: installation. FLOOR ANCHORED CEILING HUNG OVERHEAD BRACED FLOOR-TO- CEILING ANCHORED

IMPORTANT: installation. FLOOR ANCHORED CEILING HUNG OVERHEAD BRACED FLOOR-TO- CEILING ANCHORED INSTALLATION INSTRUCTIONS MAXIMUM PRIVACY COMPACT LAMINATE TOILET PARTITIONS 2080 DuraLineSeries 2180 DuraLineSeries Class-A Fire Rated Includes Institutional Hardware Option.67 IMPORTANT: Storage and

More information

BioPrism Solid Surface

BioPrism Solid Surface Please read all instructions before installing products. These instructions are intended for use with InPro s standard toilet partitions, which include 58 high doors and wall panels, when deviating from

More information

INSTALLATION INSTRUCTION

INSTALLATION INSTRUCTION INSTALLATION INSTRUCTION Soild Phenolic Series contents page 1080 DuraLineSeries...2-21 1180 DuraLineSeries...2-21 2080 DuraLineSeries Maximum Privacy...22-41 2180 DuraLineSeries Maximum Privacy...22-41

More information

INSTALLATION INSTRUCTIONS FOR PLASCORE NARROW STILE DOORS

INSTALLATION INSTRUCTIONS FOR PLASCORE NARROW STILE DOORS INSTALLATION INSTRUCTIONS FOR PLASCORE NARROW STILE DOORS The following information is provided by Plascore, Inc., as a general guideline for the installation of the Plascore Narrow Stile Door and Jamb

More information

Franklin Mills Stackable Movable Lateral Instructions

Franklin Mills Stackable Movable Lateral Instructions Franklin Mills Stackable Movable Lateral Instructions Table of Contents: Table of contents...1 Tools Required...2 Stationary Shelving Assembly...3-7 Mobile Shelving Assembly...8-16 Rail Assembly...8-11

More information

Dura-Lock Roof System

Dura-Lock Roof System DLR-14 Dura-Lock Roof System Assembly and Installation Instructions Read the instructions before starting the job. They explain the steps required to produce a finished product that will meet factory specifications.

More information

PROFILE Flat Panel Console System Installation Manual

PROFILE Flat Panel Console System Installation Manual PROFILE Flat Panel Console System Installation Manual Table of Contents Page Introduction... 2 Important Safety Information...3, 4 Installation Overview... 4, 5, 6 Single Sided/Single Unit... 7 Double

More information

INSTALLATION INSTRUCTIONS KK-K9-F14-K K9 KIT FOR FORD EXPEDITION

INSTALLATION INSTRUCTIONS KK-K9-F14-K K9 KIT FOR FORD EXPEDITION INSTALLATION INSTRUCTIONS KK-K9-F14-K-32 32 K9 KIT FOR 2003-2016 FORD EXPEDITION TOOLS REQUIRED: Power Drill Drill Bit Set Standard & Metric Socket Sets Phillips Screw Driver Open End Wrench Set Wire Cutters

More information

Installation and Operation Manual. Ajustable Valance Kits CAUTION: Duke Manufacturing Co.

Installation and Operation Manual. Ajustable Valance Kits CAUTION: Duke Manufacturing Co. Installation and Operation Manual Ajustable Valance Kits 2502757 2502857 : Please read this manual completely before attempting to install, operate or service this equipment This manual is Copyright 2018

More information

Pickup Box Utility Rack Package Installation (Instruction ID: )

Pickup Box Utility Rack Package Installation (Instruction ID: ) 017 Chevrolet Colorado Pickup - WD (VIN S) Canyon, Colorado Accessory Installation Manual N America Document ID: 3966961 Pickup Box Utility Rack Package Installation (Instruction ID:3144879) Installation

More information

Transit Connect Full/Half Installation Instructions

Transit Connect Full/Half Installation Instructions GATHER THESE TOOLS FOR ASSEMBLY & INSTALLATION 7/16 wrench, T45 Torx socket, 7/16 socket, 3/8 drive ratchet - 3/8 socket One 1/8 square end driver bit provided - Electric drill/driver/18v cordless One

More information

Height Adjustable Benching End Panel and Utility Pole

Height Adjustable Benching End Panel and Utility Pole Height Adjustable Benching End Panel and Utility Pole Tools required: END PANEL Jig Saw Power Drill END PANEL WITH UTILITY POLE Bit Holder Long #2 Square Drive Bit 5mm Hex Drive Bit UTILITY POLE Level

More information

Assembly Instructions 10 X 10 Aluminum Frame Building

Assembly Instructions 10 X 10 Aluminum Frame Building Assembly Instructions 10 X 10 Aluminum Frame Building 27 97 9 8 47 36 74 52 10 10 X 10 Square Building W/ Dome Includes: The Steel Entry Door with a Dead Bolt Lock assembly and Aluminum Door Frame. Metal

More information

INSTRUCTION BOOKLET #C21. For Wallbed models: KING SIZE

INSTRUCTION BOOKLET #C21. For Wallbed models: KING SIZE For Wallbed models: KING SIZE INSTRUCTION BOOKLET #C1 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION PROCESS COULD RESULT

More information

Insolroll Clutch Operated Shades Installation Instructions Installation Instructions

Insolroll Clutch Operated Shades Installation Instructions Installation Instructions All clutch operated shades are shipped fully assembled and ready for installation. Mounting screws are not provided. Screws for chain guide installation to meet the child safety standards are provided.

More information

RAMPAGE P R O D U C T S. INSTALLATION INSTRUCTIONS BRONCO ZIPPER FASTRACK TOP PART #984xx BRONCO TOOLS REQUIRED

RAMPAGE P R O D U C T S. INSTALLATION INSTRUCTIONS BRONCO ZIPPER FASTRACK TOP PART #984xx BRONCO TOOLS REQUIRED RAMPAGE P R O D U C T S 84 (+/- 1/4 ) INSTALLATION INSTRUCTIONS BRONCO ZIPPER FASTRACK TOP PART #984xx BRONCO 1966-1977 TOOLS REQUIRED 3/8 WRENCH 7/16 WRENCH ½ WRENCH #2 PHILLIPS SCREWDRIVER 1/8 DRILL

More information

S6 User s Manual USER S MANUAL ver. 1.0

S6 User s Manual USER S MANUAL ver. 1.0 S6 User s Manual SKEETER - 1U LOW PROFILE SOLUTION Table of Contents Tabletop Configuration 2 Tabletop Configuration Accessories 4 Slide Configuration 5 slide configuration accessories 7 rack Mount configuration

More information

https://www.wallbedsbywilding.com/wallbed-installation-studio-series/

https://www.wallbedsbywilding.com/wallbed-installation-studio-series/ For Wallbed models: KING SIZE INSTRUCTION BOOKLET #C1 Watch step by step installation instructions at: https://www.wallbedsbywilding.com/wallbed-installation-studio-series/ WARNING! ALL MURPHY/WALLBED

More information

Assembly Instructions Above Worksurface Riser Shelf Systems and Back / End Stops

Assembly Instructions Above Worksurface Riser Shelf Systems and Back / End Stops Assembly Instructions Above Riser Shelf Systems and Back / End Stops Back Stops and End Stops Adjustable Riser Shelves Instrument Riser Shelves Stationary Riser Shelves IMPORTANT PLEASE READ THESE INSTRUCTIONS

More information

NOTE: Top section pole (Q) is packed INSIDE bottom section pole (S)

NOTE: Top section pole (Q) is packed INSIDE bottom section pole (S) Form 0905-0 Instructions and Parts List TM- Mini Castle (modified) MARTIN SAFETY SYSTEM NOTES: () A complete system is packed in two boxes post box and house box. House box contains hardware for both post

More information