COURTYARD PATIO COVER INSTALLATION INSTRUCTIONS
|
|
- Ira Newton
- 5 years ago
- Views:
Transcription
1 COURTYARD PATIO COVER INSTALLATION INSTRUCTIONS Recommended Tools: Electric Drill w/ Bits, Rachet or Nut Driver w/ Sockets, Level, Tape Measure, Screw Drivers (Phillips & Regular), Ladder Before You Begin: 1.) Please read all instructions carefully. Check Bill of Materials for any missing parts, and gather all necessary tools. The paint finish can be scratched so place materials on tarp or cardboard to prevent scratching. 2.) Note that this awning cover kit is not designed to carry additional loads such as hanging plants, swings, people, trellis's, or other objects. Rev'd - 11/01/05
2 COURTYARD AWNING PARTS LIST 1. Lower Column Bracket 2. Upper Column Bracket 4. Tension Tube Cap 5. Tension Tube 6. Mounting Strip 7. Awning Fabric 8. Fabric Valance /2" Sq. Post or Decor. Column Front Splice Bar (Optional) 10. Front Frame Rail /2" Lag Screw 14. 1/4" x 2 1/2" Bolt w/ Wing Nut 15. 3/16" x 1" Bolt w/ Wing Nut 3. Tension Bolt Assy. 16. #8 x 3/4" Tek Screw
3 STEP 1 Mark screw holes in mounting channel at 12" or 16" O.C. as per wall stud location and drill 1/4" holes. Determine proper mounting height before marking and drilling holes in wall using mounting channel as a guide. Be sure to allow for ample head room above out swinging doors and accomadate the required amount of drop. (Refer to Fig 1-2 for Mounting Height Table.) 1 1/2" Lag Screw (refer. to Step 8) Wall Mounting Channel MOUNTING HEIGHT ** See Fig. 9-1 for Illustration of Terms ** Mounting Height Column Height + Recomended Drop 1.) Use Table Below to Determine Rec'd Drop. 2.) Add Rec'd Drop to Col. Ht. to Find Mtg. Ht. - or - if You Know Mtg. Ht. Subtract Rec'd Drop from it to find Col. Ht. for Step 9. Awnings w/ Textilene Fabric Recom'd Projection Drop Awnings w/ Sunbrella Fabric Recom'd Projection Drop 6'-0" 12" 6'-0" 16" 8'-0" 14" 8'-0" 22" 10'-0" 16" 10'-0" 26" 12'-0" 18" 12'-0" 30" Fig. 1-1 Fig. 1-2 STEP 2 Spread out fabric and slide side frames onto each end of fabric (see Fig. 2-1). Slide front frame onto front of fabric until ends are even with side frames (see Fig 2-2). Awning Fabric Fig. 2-1 (Grommets to the Front) Fig. 2-2 Front Frame Rail Awning Fabric
4 STEP 3 (OPTIONAL FRONT FRAME SPLICE) If front frame rails of your awning require splicing simply insert the center splice bar into adjoining ends of the front frame rails and secure threw the existing holes w/ 4 - #8 x 3/4" Tek Screws (see Fig 4-1). Front Frame Rail Fig. 4-1 #8 x 3/4" Tek Screw Center Splice Bar STEP 4 Lock front frames into side frames by inserting front frame ends into the pre-cut notches provided in the side frames Fasten frame ends and fabric together using a 1/4" x 2 1/2" bolt w/ wing nut at each end (see Fig. 3-1). Grommet in Awning Fabric Front Frame Rail 1/4" x 2 1/2" Bolt Corner Splice Bar Fig /4" Wing Nut
5 STEP 5 Slide mounting channel onto fabric (see Fig. 5-1). Place two 3/8" nuts onto tensioner bolts as shown in the Parts List on pg.2. Insert the tension bolt into mounting Channel and slide all but the outer 2 bolts into position. Be sure to align tension bolts with tensioning tube caps on front frame (see Fig. 5-2). Wall Mounting Channel Awning Fabric Awning Fabric Wall Mounting Channel Tensioning Nut Fig. 5-1 w/ Tensioner Cap Fig. 5-2 Locking Nut STEP 6 Insert outer two tension bolts into tube caps on side frames. Place bolt heads into mounting strip by sliding strip back and forth (see Fig. 6-1). Tighten The tension bolts to mounting channel by turning 3/8" nut closest to mtg. channel. Place tensioning tube caps onto tensioning tubes (see Fig. 6-2). Wall Mtg. Channel Tensioning Bolt Assy. Awning Fabric Tensioner Cap Fig. 6-1 Fig. 6-2 Tighten Locking Nut to Mtg. Strip Move Tnsn. Nut Towards Cap to Tighten Fabric
6 STEP 7 Place tensioning tube caps onto tensioning tubes and slide cap/tube assemblies onto the remaining tensioning bolts (see Fig. 7-1). Seat the open end of cap/tube assemblies into caps mounted along the front frame (see Fig. 7-2). (Note: We recomend completing Step 7 with the Awning Assy. turned upside-down as shown in Fig. 7-1 & 7-2.) Wall Mounting Channel Tensioning Bolt & Nut Assy. Fr. Frame Rail w/ Caps Attached Fabric Tensioning Tube Tensioning Tube Cap Tensioning Tube Fig. 7-1 Fig. 7-2 STEP 8 Lift the assembly up to the desired location and support the front with a ladder. Attach the mounting channel to wall using 2" lag screws (see Fig. 8-1). Turn tensioning nuts on the tensioning bolts toward the front of the cover until fabric becomes taunt (see Fig 8-2). Wall Mounting Channel 1 1/2" Lag Screw Locking-Nut Tightened to Mtg. Channel Adjust Nut As Shown to Tighten Awning Tensioning Tube/Cap Assy. Reconnect Mtg. Channel to Wall w/ 1 1/2" Lag Ladder Screws (See Fig 1-1) Fig. 8-1 Awning Assembly Fig. 8-2
7 STEP 9 Cut Columns to length making sure to to get the required amount of drop (see Fig. 1-1 & 9-1). NOTE: Refer Fig. 1-1 for recomended drop as per projection. Fasten column brackets to one end of columns using 2 - #8 x 3/4" Tek screws per bracket, and slide column/bracket assembly into slot along front frame (see Fig. 9-2). Upr. Column Bracket #8 x 3/4" Tek Screw Fr. Frame Rail Fig. 9-1 Fig. 9-2 Decoritive Column STEP 10 Insert Lower Column Brackets into bottoms of columns, level columns, and anchor brackets to ground with 2-2" lag screws per bracket. Secure columns to brackets with 2 - #8 x 3/4" Tek screws per bracket (see Fig 10-1). Once columns are anchored, drill a 3/16" hole through the upper column bracket / front frame connection and fasten with 3/16" x 1" bolt and wing nut (see Fig. 10-2). Decor. Column #8 x 3/4" Tek Screw Fr. Frame Rail 1 1/2" Lag Bolt 3/16" x 1" Bolt w/ Wing Nut Fig Lwr. Column Bracket Fig Decor. Column
8 STEP 11 Cover rough and sharp edges on front corners with velcro strips. Begin installing the valance by sliding it into front frame (see Fig 11-1) and followed by feeding both ends into side frames (see Fig 11-2). Side Frame Center Valance in Front Frame Rail First Valance End Front Frame Rail Fig Fig CONGRATULATIONS, ASSEMBLY COMPLETED! Other Products by Americana Building Products Include: Fabric Window Awnings, Aluminum Patio Covers and Window Awings, Glass Enclosures, Screen Enclosures, Park Shelters, Aluminum Railings & Columns, Retractable Fabric Awnings & More!
COURTYARD DOOR CANOPY INSTALLATION INSTRUCTIONS
COURTYARD DOOR CANOPY INSTALLATION INSTRUCTIONS Recommended Tools: Electric Drill w/ Bits, Rachet or Nut Driver w/ Sockets, Level, Tape Measure, Screw Drivers (Phillips & Regular), Ladder Before You Begin:
More informationOZARK DOOR CANOPY ASSEMBLY INSTRUCTIONS
OZARK DOOR CANOPY ASSEMBLY INSTRUCTIONS Recommended Tools: Level, Pliers, 3/8" Electric Drill, Carpenters Square, Tape Measure, Metal Hack Saw, Silicone Caulking, Screw Drivers (Regular & Phillips) Before
More informationLevel, Pliers, 3/8" Electric Drill, Carpenters Square, Tape Measure, Metal Hack Saw, Silicone Caulking, Screw Drivers (Regular & Phillips)
Delta Door Canopy Installation Instructions Recommended Tools: Before You Begin: Level, Pliers, 3/8" Electric Drill, Carpenters Square, Tape Measure, Metal Hack Saw, Silicone Caulking, Screw Drivers (Regular
More informationLAS VEGAS PATIO COVER INSTALLATION INTSRUCTIONS
STEP 8. Drill 2-5/8" dia. holes in the outer face of the ledger board spaced evenly (approximently 24" O.C.). Hoist the ledger board into place, centering it in front of the gutter. Anchor the inner face
More informationATTACHED PERGOLA ARBOR INSTALLATION INSTRUCTIONS
ATTACHED PERGOLA ARBOR INSTALLATION INSTRUCTIONS Recommended Tools: Before You Begin: Saftey Glasses, Tape Measure, Carpenters Level, Framing Square, Hex Head Nut Drivers, Chalk Line Elec. Drill w/ Bits
More information4-SIDED NAVAJO SHELTER ARIZONA MODEL INSTALLATION INSTRUCTIONS
4-SIDED NAVAJO SHELTER ARIZONA MODEL INSTALLATION INSTRUCTIONS Recommended Tools: Before You Begin: Saftey Glasses, Tape Measure, Carpenters Level, Framing Square, Hex Head Nut Drivers, Chalk Line, Elec.
More informationRecommended Tools: Before You Begin:
Recommended Tools: Before You Begin: Saftey Glasses, Tape Measure, Carpenters Level, Framing Square, Hex Head Nut Drivers, Chalk Line Elec. Drill w/ Bits (Masonry Drill, Bits. & Anchors maybe required
More informationIMPORTANT -- SPECIAL INSTALLATION INSTRUCTIONS
IMPORTANT -- SPECIAL INSTALLATION INSTRUCTIONS ** READ ALL INSTALLATION INSTRUCTIONS BEFORE STARTING!** If at any point, you have questions, call 1-800-851-0865...(The manufacturer will not be responsible
More informationIMPORTANT -- SPECIAL INSTALLATION INSTRUCTIONS
IMPORTANT -- SPECIAL INSTALLATION INSTRUCTIONS ** READ ALL INSTALLATION INSTRUCTIONS BEFORE STARTING!** If at any point, you have questions, call 1-800-851-0865...(The manufacturer will not be responsible
More informationIMPORTANT -- SPECIAL INSTALLATION INSTRUCTIONS FOR AZTEC SHELTER
IMPORTANT -- SPECIAL INSTALLATION INSTRUCTIONS FOR AZTEC SHELTER ** READ ALL INSTALLATION INSTRUCTIONS BEFORE STARTING!** If at any point, you have questions, call 1-800-851-0865...(The manufacturer will
More informationIMPORTANT -- SPECIAL INSTALLATION INSTRUCTIONS
IMPORTANT -- SPECIAL INSTALLATION INSTRUCTIONS ** READ ALL INSTALLATION INSTRUCTIONS BEFORE STARTING!** If at any point, you have questions, call 1-800-851-0865...(The manufacturer will not be responsible
More informationINS T A L L A TIO N INS T R U C TIO N S. Ceiling Mount Track System
Ceiling Mount Track System 10.26.2016 Specifications Ceiling Post: Unassembled 2-7/8 Assembled 1-11/16 7/8 7-9/16 5-7/8 3/8 2 Tubes 1/2 2-3/8 5 Parts and Tools Tools Needed Tape Measure Pencil Drill with
More informationALUMA-VENT AWNING REGULAR END STYLE INSTALLATION INSTRUCTIONS
ALUMA-VENT AWNING REGULAR END STYLE INSTALLATION INSTRUCTIONS Contact us at: 1-888-442-2928 or www.americana.com Options in your kit: A. Splice Pg 16 B. Column Pg 17 C. C-Channel Brace Pg 19 D. Runner
More informationATTACHED DOUBLE HEADER PERGOLA ASSEMBLY INSTRUCTIONS
ATTACHED DOUBLE HEADER PERGOLA ASSEMBLY INSTRUCTIONS Before You Begin: Recommended Tools: Note on Masonry Units: Note on Electric Drills: Note on Cutting and Drilling: 1) Please read all instructions and
More informationATTACHED SINGLE HEADER PERGOLA ASSEMBLY INSTRUCTIONS
ATTACHED SINGLE HEADER PERGOLA ASSEMBLY INSTRUCTIONS Before You Begin: Recommended Tools: Note on Masonry Units: Note on Electric Drills: Note on Cutting and Drilling: 1) Please read all instructions and
More informationALUMA VENT AWNING REGULAR END STYLE ASSEMBLY INSTRUCTIONS
Contact us @ (800)851-0865 ALUMA VENT AWNING REGULAR END STYLE ASSEMBLY INSTRUCTIONS Recomended Tools: Elec. Drill or Battery Powered Screw Driver 1/4" Socket Phillips Screw Driver Pliers Plus: The correct
More informationFREESTANDING DOUBLE HEADER PERGOLA ASSEMBLY INSTRUCTIONS
FREESTANDING DOUBLE HEADER PERGOLA ASSEMBLY INSTRUCTIONS Before You Begin: Recommended Tools: Note on Masonry Units: Note on Electric Drills: Note on Cutting and Drilling: 1) Please read all instructions
More informationAssembly and installation help
Assembly and installation help A supplement to the directions The Purpose of this tutorial is to expand (not replace) upon the directions that come with the system and to help provide shortcuts, the first
More informationAWNING / PATIO COVER INSTALLATION INSTRUCTIONS
AWNING / PATIO COVER INSTALLATION INSTRUCTIONS Before You Begin Read the installation instructions thoroughly before beginning the installation procedure. Perspective In the Awning Instructions, Back means
More informationYUKON PATIO COVER INSTALLATION INSTRUCTIONS
YUKON PATIO COVER INSTALLATION INSTRUCTIONS Before You Begin: Consult your local building department for any required permits You may be required to obtain a building permit for this structure. Contact
More informationBox Track INSTALLATION INSTRUCTIONS
Box Track INSTALLATION INSTRUCTIONS BOX TRACK Recommended Tools Level Tape Measure Pencil Drill with 1/8, and 1/4, Drill Bits, Phillips Bit and Slotted Bit Socket Wrench with 9/16 Socket 9/16 and 5/8 Wrench
More informationDura-Lock Roof System
DLR-14 Dura-Lock Roof System Assembly and Installation Instructions Read the instructions before starting the job. They explain the steps required to produce a finished product that will meet factory specifications.
More informationINSTRUCTION BOOKLET #C0 Watch step by step installation instructions at: https://www.wallbedsbywilding.com/wallbed-installation-studio-series/ WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY.
More informationContinuous Handrail Kit Installation Instructions
Continuous Handrail Kit Installation Instructions ALUMINUM RAILING SYSTEM Canadian Version Wall Application (see page 2) Railing Application (see page 7) Wall anchors not provided Hardware included: 1x
More informationALUMA VENT AWNING WITH VALANCE END ASSEMBLY INSTRUCTIONS
Contact us @ (800)851-0865 ALUMA VENT AWNING WITH VALANCE END ASSEMBLY INSTRUCTIONS Recomended Tools: Drill or Elec. Screw-driver 1/4" Socket Phillips Screw Driver Pliers Plus: The correct screws/anchors
More informationINSTRUCTION BOOKLET #C10 Watch step by step installation instructions at: https://www.wallbedsbywilding.com/wallbed-installation-studio-series/ WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY.
More informationHeavy Duty I-Beam Trolley
Heavy Duty I-Beam Trolley ASSEMBLY INSTRUCTIONS I-BEAM TROLLEY Recommended Tools Level Tape Measure Pencil Drill with 1/8, 1/4, and 3/8, Drill Bits and Phillips Bit Socket Wrench with 9/16 Socket I-BEAM
More informationAustin Standing Seam Awning Assembly and Installation Instructions. Assembly Instructions
Austin Standing Seam Awning Assembly and Installation Instructions Be sure to use safety glasses when assembling and installing the awning. Some metal parts may have sharp edges. Use work gloves to handle
More informationSide Mount INSTRUCTION BOOKLET #C122 BED STYLE: PARK CITY
Side Mount BED STYLE: PARK CITY INSTRUCTION BOOKLET #C1 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION PROCESS COULD RESULT
More informationFor Wallbed models: KING SIZE INSTRUCTION BOOKLET #C1 Watch step by step installation instructions at: https://www.wallbedsbywilding.com/wallbed-installation-studio-series/ WARNING! ALL MURPHY/WALLBED
More informationALL SEASON PATIO COVER
ALL SEASON PATIO COVER 61 Where the All Season Patio Cover is to be attached to the home, create a level line showing where the top of the mounting rail is to be located. Install each section with the
More informationWorktop. Weight Capacity. 100 lbs. 21 Corner Worktop. 48 Worktop. Fits over 2 Cabinets. 72 Worktop. Fits over 3 Cabinets. 200 lbs. 150 lbs.
Bold.0 Warning: Excessive weight hazard! Use two or more people to move, assemble or install cabinets and locker to avoid back injury. Do not leave children unattended near cabinets. High risk of tipping
More information3 D Printer Enclosure Assembly Instructions
3 D Printer Enclosure Assembly Instructions Tools Required: 2.5 mm Allen wrench (included) Phillips screwdriver Adjustable Wrench Parts Included: Plexiglas Back with fan and filters installed (29.5 x 35.5
More informationInstallation Instructions
Please read all instructions before installing Installation Instructions Important 1. Acclimate materials 24 hrs before installation. Maintain temperature controlled environment after installation 2. Install
More informationINSTALLATION INSTRUCTIONS CONTOURED LIGHT BAR APPLICATION: CHEVY EQUINOX/ GMC TERRAIN PART NUMBERS: ,
INSTALLATION INSTRUCTIONS CONTOURED LIGHT BAR APPLICATION: 2010-2014 CHEVY EQUINOX/ GMC TERRAIN PART NUMBERS: 32-21020, 32-21025 ITEM QUANTITY DESCRIPTION TOOLS NEEDED 1 1 CONTOUR BAR TORQUE WRENCH 2 1
More informationCABANA / PAVILION ASSEMBLY ALUMINUM FRAME MODELS
Assembled cabanas are large & heavy. Assemble at place of use. CABANA / PAVILION ASSEMBLY ALUMINUM FRAME MODELS Step 1 CAUTION: To avoid damage to the finish of your Cabana frame, prepare a smooth, non-scratch
More informationInstallation Instructions 800/800W/855/G2-800 Continuous Bracket Handrails
Important 1. Acclimate materials 24 hrs before installation. Maintain temperature controlled environment after installation 2. Install in accordance with manufacturer s installation instructions. Failure
More informationWorktop INDEX eight Capacity Unpacking
Pro.0 Series Warning: Excessive weight hazard! Use two or more people to move, assemble or install cabinets and locker to avoid back injury. Do not leave children unattended near cabinets. High risk of
More informationSliding Door Kit
YOU MUST READ THIS DOCUMENT BEFORE YOU BEGIN TO ASSEMBLE THE DOOR KIT. Thank you for purchasing this GrowSpan door kit. When properly assembled and maintained, this product will provide years of reliable
More informationInstallation Instructions
Important 1. Acclimate materials 24 hrs before installation. Maintain temperature controlled environment after installation 2. Install in accordance with manufacturer s installation instructions. Failure
More informationHeavy-Duty Bypass Track System
Heavy-Duty Bypass Track System Please Note: This track system must be installed with the screws going into a solid surface such as studs or a header. Due to the spacing of the holes on these Brackets,
More informationhttps://www.wallbedsbywilding.com/wallbed-installation-studio-series/
For Wallbed models: KING SIZE INSTRUCTION BOOKLET #C1 Watch step by step installation instructions at: https://www.wallbedsbywilding.com/wallbed-installation-studio-series/ WARNING! ALL MURPHY/WALLBED
More informationAssembly Instructions
Unite Panel System Hinge Door July 2016 #12 x / slotted hex washer head bolt Figure 1 threshold bracket frame Detail F threshold bracket threshold bracket (installed) #12 x / slotted hex washer head bolt
More informationIMPORTANT -- SPECIAL INSTALLATION INSTRUCTIONS
IMPORTANT -- SPECIAL INSTALLATION INSTRUCTIONS ** READ ALL INSTALLATION INSTRUCTIONS BEFORE STARTING!** If at any point, you have questions, call 1-800-851-0865...(The manufacturer will not be responsible
More informationM10 x 75mm Sockethead Cap Screws. 5mm Fender Washer (12) Included - (8) Required. #10 x 2.5" PH Wood Screws. (30) Included - (24) Required
Door System Unit - Hardware Tools Included: (2) 2mm Allen Wrenches, (2) 3mm Allen Wrenches, (2) 4mm Allen Wrenches, (2) 6mm Allen Wrenches, and (1) 8mm T-Handle Allen Wrench Tools Required: Phillips Screwdriver,
More informationGlideRite Retractable Cover System For Hot Spot Spas (SE & SLX only)
List of Contents Quantity Description 12 #10 x 1 ½ Flat Head Phillips Screw (see pg. 2) 2 #10 x ½ Pan Head Phillips Screw (see pg. 2) 8 ¼ x 2 ½ Lag Bolt (see pg. 2) 7 ¼ 20 x 5 / 8 Hex Head Bolt (see pg.
More informationDouble Screen Door Installation Instructions
Double Screen Door Installation Instructions (36) #8x1 tek screws (20) #8x1/2 tek screws Package Includes: (2) PCA Screen Doors (1) Astragal (1) Left Hand Z-bar (1) Right Hand Z-bar (1) Header Z-bar (2)
More informationSliding Door Kit
YOU MUST READ THIS DOCUMENT BEFORE YOU BEGIN TO ASSEMBLE THE DOOR KIT. Thank you for purchasing this GrowSpan door kit. When properly assembled and maintained, this product will provide years of reliable
More informationDublin Stalls Installation Instructions
Dublin Stalls Installation Instructions RAMM Horse Fencing and Stalls 13150 Airport Hwy. Swanton, OH 43558-9615 1-800-434-8456 Rev. 9/13/17 Part Identification Round Track Bracket (4) (Not Painted) Round
More informationSeries 1100 Aluminum Door Canopy
Series 00 Aluminum Door Canopy with Support Arms It is our recommendation that you read instructions carefully prior to assembly and installation. Series 00 with Support Arms MOUNTING BAR (A) TOP TRIM
More informationINSTALLING INVISIRAIL GLASS PANELS POST INFORMATION... 2 PRE-INSTALLATION... 2
Contents POST INFORMATION... 2 PRE-INSTALLATION... 2 STEP A1: MEASURING FOR INVISIRAIL CUSTOM GLASS PANELS (skip if using Standard Sized Panels)... 2 STEP A2: GATHER ADDITIONAL TOOLS/SUPPLIES... 2 STEP
More informationLOFT DOOR HANGER BARN DOORS & HARDWARE. Hardware Installation Instructions. Page
LOFT DOOR HANGER Page 1 Specifications 2 7/16" 3/8" 1-1/2 1-3/4 Ø3 3 7/8" 11-1/16 Page 2 Parts and Tools Tools Needed Tape Measure Pencil Drill with 1/8, 1/4 and 3/8 bits, 1 spade bit and Phillips bit
More informationABRI Fixed Classic Roof / Single Rail System Step by Step Assembly Instructions
ABRI Fixed Classic Roof / Single Rail System Step by Step Assembly Instructions Before You Begin These installation instructions will lead you through the process of installing your new shelter. The installation
More informationINSTALLATION GUIDE 2009-CURRENT HUMMER H3T PRODUCT CODE:
INSTALLATION GUIDE 2009-CURRENT HUMMER H3T PRODUCT CODE: 268 June 22, 2010 TOOLS NEEDED COMPONENTS INCLUDED P2 Tip 3/8" Drill Rubber Gasket(s) x 2 Bracket(s) x 2 1/2" Drill Bit Bulkhead Flange #2 Phillips
More informationRough Country JK Modular Winch Mount Bumper With Light End Caps
Rough Country JK Modular Winch Mount Bumper With Light End Caps Note: These instructions involve cutting parts of your vehicle. Please read all instructions prior to starting. Note: This installation also
More informationInstallation Instructions 1200/1255/G Handrails International Compliant
Important 1. Acclimate materials 24 hrs before installation. Maintain temperature controlled environment after installation 2. Install in accordance with manufacturer s installation instructions. Failure
More informationTherma-Tru Door Gallery Setup Instructions Swing Unit with Hardware Kit - Hardware Part # MADGSWU15 (Swing Unit) Part # MADGHKSU10 (Hardware Kit)
Swing Unit with Hardware Kit - Hardware Tools Included: 4mm Allen Wrench, 6mm Allen Wrench, 8mm T-Handle Allen Wrench (1) 3/4" Drill Bit, (1) 7/32" Drill Bit and Hole Template Guide Tools Required: Phillips
More informationPOWER PET. Low-E Automatic Patio Pet Door Installation and Operating Instructions
POWER PET Low-E Automatic Patio Pet Door Installation and Operating Instructions Power Pet, Regular Height, Patio Door Assembly Steps Estimated assembly time: Under 1 hour STEP 1: Assemble the tools you
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS For Wallbed models: Do-It-Yourself BOOKLET #C90 WARNING! ALL MURPY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION
More informationThe Festival Assembly Instructions
The Festival Assembly Instructions Toll Free: 866.768.8465 Hours: 9-5 Monday-Friday EST www.homeplacestructures.com Package ships as shown CONTACT INFORMATION: HomePlace Structures 301 Commerce Drive New
More informationInstallation Manual MODEL NE-42
Installation Manual MODEL NE-42 GET TO KNOW YOUR UNIT 1 1. CROSS BRACES - Stud Finder - 12-14 Level - Tape Measure - Small Flathead Screwdriver Tools Needed: - Electric Drill (with 1/4 & 1/8 drill bit)
More informationTHANK YOU FOR PURCHASING FROM HERITAGE PATIOS
Installation Guide THANK YOU FOR PURCHASING FROM HERITAGE PATIOS Your purchase is engineered by nearly a half century of commercial and residential product design proudly manufactured in the USA from responsibly
More informationREVIEW ENTIRE INSTALLATION GUIDE. This step gives you the opportunity to contact your dealer to answer any questions before you begin.
Cabriolet Shelter (Retractable Roof) Step by Step Assembly Instructions Before You Begin These installation instructions will lead you through the process of installing your new shelter. The installation
More informationParts Included: Tools Required: Canvas Office Landscape Interiors Off Module 90 Connector Kit Installation and Disassembly for Recycling Instructions
Y Parts Included: Canvas Office Landscape Interiors Off Module 90 Connector Kit Installation and Disassembly for Recycling Instructions FT127.A N Shim A Light Seal B Foam Light Seal C G H Double-Face Tape
More informationArtisan Vinyl Pergola
Artisan Vinyl Pergola Assembly Manual Thank you for your purchase of this Pergola. Beefy Vinyl Pergola Assembly Manual This manual is designed to simplify the assembly process, however we recommend having
More informationRipple Hanger ASSEMBLY INSTRUCTIONS
Ripple Hanger ASSEMBLY INSTRUCTIONS RIPPLE HANGER Recommended Tools Drill with 1/8, 1/4, and 1/2 Drill Bits, 1-1/8 Forstner Bit or 1-1/8 Spade Bit, and Phillips Bit 9/16 and 5/8 Combination Wrench Socket
More informationICU TRACKLESS SLIDING DOOR
Interior View 0 Installation Instructions Tools Required: Screwdrivers Small Straight (Flat Blade) - for Terminal Block wiring # Phillips (Crosspoint) - for various #8, #0, and #4 screws Wrenches / Sockets
More information10x10 Trellis Pergola
0x0 Trellis Pergola ASSEMBLY GUIDE Ver.-007 Table of Contents PAGE 0x0 Trellis Pergola Introduction & Overview...................................................... Pergola Materials Overview..............................................................
More informationCONTENTS TOOL LIST U P S I D E I N N O V A T I O N S, L L C RAMP AND STEP SYSTEM ASSEMBLY INSTRUCTIONS. Revised: June 2013
U P S I D E I N N O V A T I O N S, L L C RAMP AND STEP SYSTEM ASSEMBLY INSTRUCTIONS TOOL LIST Required Tools: - Reciprocating Saw with Metal Cutting Blade - Drill - 7/16 Drill Bit for Metal Drilling -
More informationSeries 1500 Aluminum Door Canopy
Series 500 Aluminum Door Canopy with Sidewings It is our recommendation that you read instructions carefully prior to assembly and installation. Series 500 with Sidewings mounting bar (A) top trim (B)
More informationBaby Grande or Grande Crank Shade with Cables and Housing Installation Instructions
Baby Grande or Grande Crank Shade with Cables and Housing Installation Instructions Tools Needed Drill 3/8 Metal Drill Bit Screwdriver (Flat & Phillips) Measuring Tape Pencil 4 Level Plumb Line ¼ Masonry
More informationESA-200 Fixed Sidelite
Exterior View Installation Instructions For use with ESA II Controller 1 Tools Required: Suggested Fasteners Required - (Not supplied) Screwdrivers Small Straight (FlatBlade) - for Terminal Block wiring
More informationWILDING WALLBEDS INSTALLATION INSTRUCTION Side Mount
WILDING WALLBEDS INSTALLATION INSTRUCTION Side Mount For Wallbed models: Do-It-Yourself Insturction booklet C92 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE
More informationStag Hanger ASSEMBLY INSTRUCTIONS
Stag Hanger ASSEMBLY INSTRUCTIONS STAG HANGER Recommended Tools Drill with 1/8, 1/4, and 3/8 Drill Bits, 1-1/8 Forstner Bit or 1-1/8 Spade Bit, and Phillips Bit 9/16 and 5/8 Combination Wrench Socket Wrench
More informationContour Hanger ASSEMBLY INSTRUCTIONS
Contour Hanger ASSEMBLY INSTRUCTIONS CONTOUR HANGER Recommended Tools Drill with 1/8, 1/4, and 3/8 Drill Bits, 1-1/8 Forstner Bit or 1-1/8 Spade Bit, and Phillips Bit 9/16 and 5/8 Combination Wrench Socket
More informationIndustrial Hanger ASSEMBLY INSTRUCTIONS
Industrial Hanger ASSEMBLY INSTRUCTIONS INDUSTRIAL HANGER Recommended Tools Drill with 1/8, 1/4, and 3/8 Drill Bits, 1-1/8 Forstner Bit or 1-1/8 Spade Bit, and Phillips Bit 9/16 and 5/8 Combination Wrench
More informationInstallation Manual for Metal Toilet Partitions Standard Series
For Video instructions http://www.hadrian-inc.com/tech-data/installation/toilet-partitions.aspx P a g e 1 Table of Contents Page General Notes and Tools Required 3 STEP 1: Establish Floor Bracket Locations
More informationWireCrafters, LLC. General Information
WireCrafters, LLC. General Information 6208 Strawberry Lane 502/363-6691 www.wirecrafters.com Louisville, Kentucky 40214 502/361-3857 FAX 1-800-626-1816 The following General Installation Instructions
More informationInstallation Instructions 800/800W/855/G2-800 Handrails
Important 1. Acclimate materials 24 hrs before installation. Maintain temperature controlled environment after installation 2. Install in accordance with manufacturer s installation instructions. Failure
More informationINSTRUCTION BOOKLET #C21. For Wallbed models: KING SIZE
For Wallbed models: KING SIZE INSTRUCTION BOOKLET #C1 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION PROCESS COULD RESULT
More informationV nyl Gazebo truct c it Assembly Instr ons
V nyl Gazebo Vi Assembly Instr ct tr t u ru ons ct c i ti Pre-assembly Instructions A C B #1 - Site properly prepared. 4" - 6" clean stone 9 linear blocks 2" x 8" x 16" C C A A B B #1a - 12" sauna tubes,
More informationInstallation Manual MODEL ANE-42
Installation Manual MODEL ANE-42 GET TO KNOW YOUR UNIT 1 2 1. CROSS BRACES 2. SIDE BRACKETS - Stud Finder - 12-14 Level - Tape Measure - Small Flathead Screwdriver Tools Needed: - Electric Drill (with
More informationBlackout Fan Kits with Breathable Wall Light Traps
Blackout Fan Kits with Breathable Wall Light Traps 2018 Growers Supply All Rights Reserved. Reproduction is prohibited without permission. Maintain controlled airflow without sacrificing blackout environments.
More information4-lite Patio Door. Installation Instructions
4-lite Patio Door Installation Instructions IMPORTANT: Read the instructions and familiarize yourself with the door parts and pieces before beginning assembly and installation. Note: Only the 5-0 x 6-8
More informationTERRACE / TERRACE CONCEPT Retractable Classic Roof / Double Rail System Step by Step Assembly Instructions
TERRACE / TERRACE CONCEPT Retractable Classic Roof / Double Rail System Step by Step Assembly Instructions Before You Begin These installation instructions will lead you through the process of installing
More informationINSTRUCTION SHEET U19
U19 All Refrigerator and All Freezer Trim Kit Installation Product Line: U19 All Refrigerator and All Freezer Models Parts Included in Kit TRIMKITEZ1 (Part# 297333500): Single Trim Kit Components Single
More informationESA-100 Fixed Sidelite/Non Breakout
/Non Breakout Exterior View Installation Instructions For use with ESA II Controller 1 Tools Required: Suggested Fasteners Required - (Not supplied) Screwdrivers Small Straight (FlatBlade) - for Terminal
More informationSpoked GARRICK HANGER
Spoked GARRICK HANGER ASSEMBLY INSTRUCTIONS SPOKED GARRICK HANGER Recommended Tools Drill with 1/8 and 1/4 Drill Bits, 1-1/8 Forstner Bit or 1-1/8 Spade Bit, and Phillips Bit 9/16 and 5/8 Combination Wrench
More informationEZ-MATRIX I N S TA L L AT I O N I N S T R U C T I O N S EZ-MATRIX
TM I N S TA L L AT I O N I N S T R U C T I O N S READ THESE INSTRUCTIONS page 2 Installer Tips: Installation is best completed with the help of one or two people. Prior to beginning, please read through
More informationGlideRite Retractable Cover System For HotSpring & Tiger River Spas (except Classic & pre-2000 Landmark Spas)
List of Contents Quantity Description 12 #10 x 1 ½ Flat Head Phillips Screw (see pg. 2) 2 #10 x ½ Pan Head Phillips Screw (see pg. 2) 8 ¼ x 2 ½ Lag Bolt (see pg. 2) 7 ¼ 20 x 5 / 8 Hex Head Bolt (see pg.
More informationOxford Stalls Installation Instructions
Oxford Stalls Installation Instructions RAMM Horse Fencing and Stalls 13150 Airport Hwy. Swanton, OH 43558-9615 1-800-434-8456 Rev. 8/15/17 Before You Start Typical stall sizes are 10 x 10, 12 x 12 or
More informationROCKWELL. Two Panel Door. Half X Door. Double X Door. Z Combination Door
ROCKWELL 4 in 1 DOOR Choose between four door styles with this Door Kit. Our versatile Rockwell Door Kit is very easy to assemble. All materials and hardware needed to assemble any of the four styles are
More informationINSTRUCTION BOOKLET #34. For Wallbed models: KING SIZE SIERRA WITH STORAGE HEADBOARD
For Wallbed models: KING SIZE SIERRA WITH STORAGE HEADBOARD INSTRUCTION BOOKLET #34 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION
More informationECLIPSE: TV COVER INSTALLATION GUIDE
ECLIPSE: TV COVER INSTALLATION GUIDE 1 Congratulations on purchasing your Eclipse Vanishing TV Mirror! Installing your TV into the Eclipse Mirror is a very simple process following these instructions.
More informationYardistry. External Display YP *Time required for assembly approximately 1.5-2hrs
Yardistry External Display YP40030 *Time required for assembly approximately 1.5-2hrs Components 4 Packages of Panel Clips (Includes 6 Panel Clips and Hardware) 3 16 1/2 x 16 1/2 Signs (hardware Included)
More informationMONKEY BARS OVERHEAD RACK INSTALLATION
MONKEY BARS OVERHEAD RACK INSTALLATION Thank you for purchasing the New Monkey Bars Overhead storage rack. The most innovative overhead rack on the market WARNING THE PROPER INSTALLATION OF THIS STORAGE
More informationTWIG Hanger ASSEMBLY INSTRUCTIONS
TWIG Hanger ASSEMBLY INSTRUCTIONS TWIG HANGER Recommended Tools Drill with 1/8, 1/4, and 3/8 Drill Bits, 1-1/8 Forstner Bit or 1-1/8 Spade Bit, and Phillips Bit 9/16 and 5/8 Combination Wrench Socket Wrench
More information11 6 Round Building Assembly Instructions
11 6 Round Building Assembly Instructions 11 6 Round Building Hardware List 1. Pro Rib Brite White 36 Wide X 68 Long (Siding Steel) 11 2. Top Wall Wheel Ring 3 3. Base Ring 3 4. 1 ½ X 68 Aluminum Tubes
More informationIDR assembly instructions:
IDR assembly instructions: Required Tools: 2 X 12mm Open End Wrench 14mm open end wrench #2 Phillips Head Screw Driver (Drill with adjustable torque clutch recommended) 8mm nut driver (Supplied in IDR-AK)
More informationWAREHOUSE HANGER INSTALLATION INSTRUCTIONS R H INS T A L L A TIO N INS T R U C TIO N S
INS T A L L A TIO N INS T R U C TIO N S WAREHOUSE HANGER NOTE: Due to the size and weight of the Warehouse Hanger it is recommended that this Hanger be installed on 3 4 or wider doors. 10.11.2016 2-3/16"
More information